Macbook Pro When warranty start?
Hi guys,
May I know when did the MacbookPro warranty start?
The date of purchased or the date of setup?
I have an unit which haven open or sealed off at all,
but it have been bought from the store a month ago.
I get few version online.
Some said the date of purchase while some said it require user to register online.
Although there are several discussion in earlier,
but that was few years ago. May I have the latest confirm info?
Anyone Please?
I don't know but I assumed the date you bought it and took possession. No not the date you open the box or register online. You have anytime during the first year of possession to buy Applecare extended warranty, a must have for any laptop due to the problems that arise.
for reference:
Direct you to the proper forum for MacBook :
MacBook Series Forums
https://discussions.apple.com/community/notebooks?view=discussions
http://www.apple.com/support/macbookpro
Mac OS X Forum
https://discussions.apple.com/community/mac_os?view=discussions
This forum deals with a desktop/tower 65lb Mac Pro
http://www.apple.com/support/macpro
Similar Messages
-
When trying to upgrade and install OS X Mmavericks to my Macbook Pro as it started to install the computer stopped the install and now is stuck with the OS X Mavericks intall window showing and I can't get out of it or force quit? I can not do anything else because this is stuck with this window/install screen showing. I have tried everything to get back to my regular desktop. I do not want to wipe the drive because I have photos on it that I want to save. So if there is any way to bypass this installer and get back to my regular desktop I would greatly appreciate the help.
UPDATE* Macbook7,1
Mavericks 10.9.4
8GB ram -
My MacBook Pro will not start. When I started it goes to a gray screen with the Apple logo and has the spinning dial. When I started in safe mode it will not start. In safe mode it as an error message that says MacBook Launch_msg(): Socket is not connected
If running 10.7 or later hold down Command-R at Startup.
This should invoke recovery Mode.
Choose Disk Utility.
Select your Hard drive. Inspect the SMART Status in the lower right of the window for "Verified".
Select the Mac OS X Volume (originally Macintosh HD) click (Repair Disk)
If errors, run again until it comes clean or gets stuck.
Report any error messages. -
My MacBook Pro won't start it just goes beep beep beep when I press the power button
My MacBook Pro won't start it just goes beep beep beep when I press the power button
Hi Csound1,
I haven't added any RAM my daughter was using the computer then it hung so powered it down then the beeping started. Do you know if there is a combination of buttons I can press when powering up that will put me in some kind of safe mode so that I can find out what's up, I tried pressing D when the beeping started but it didn't make a difference.
MC -
MacBook Pro's fans start running at high speed when the computer is asleep. Normal?
The other night, my MacBook Pro's fans started running at high speed when the computer was asleep. Loud enough to wake me up. And this just kept on going until I finally decided to turn the computer off. Is this normal? Is this anything to worry about?
This is not normal. See if a SMC reset solves the problem:
http://support.apple.com/kb/ht3964
Ciao. -
MacBook Pro does t start I turned it off during start up I've tried a lot of stuff. When I hold startup my hard disk says efi boot instead of Macintosh hd
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
If this does not work, then you will have to erase and reinstall Mountain Lion:
Install or Reinstall Lion/Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
the Security button and set the Zero Data option to one-pass. Click on
the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion/Mountain Lion and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless. -
HT204347 what to do if my macbook pro is not starting and I do not have warranty?
I need help...my macbook pro is not starting. I tried everything..Can I send it to the Apple store for an estimate and how much would that be?
Thanksemdonahue wrote:
I need help...my macbook pro is not starting. I tried everything..Can I send it to the Apple store for an estimate and how much would that be?
Thanks
Yes and ask the repair tech. -
MacBook Pro will not start up - apple logo and spinnining wheel
*The problem:*
I have a MacBook Pro bought in October 2009 and have had no problems with it up until now. When I went to turn my Macbook on the other day all I got was the initial grey screen with the apple logo and a spinning wheel. The wheel keeps spinning and never loads up my Mac. The battery is charged, I've not just downloaded/installed new soft/hardware, and I'm using the adaptor that came with the MacBook Pro when I purchased it.
*Stuff I've tried so far:*
I've read the forums/manual and have tried the following:
1. Reset the SMC - no effect
2. Reset the PRAM - no effect
3. Opened the MacBook Pro in safe mode - gets two thirds the way through the loading screen and then sops i.e. no effect
4. Done a hardware test - reported no problems
5. Started up my Mac with the original install DVD inserted into the CD drive, and performed a repair in disc utility - says there is a fault in the volume information and then repairs it at the end. Then I run it again and it says there's a fault in the volume information. It doesn't happen how many times I run the repair, it never fixes it.
6. Tried to reinstall the original disc but it cannot find the hard drive.
7. Tried to reboot but it cannot find the hard drive.
Next:
The only thing I have not yet tried is reformatting the drive. I have not tried this yet as I foolishly did not make a time machine (I didn't have an external hard drive) and I've not backed up my work for several months.
I have two questions:
1. Before I reformat, is there any way I can get documents off the system? I expect the answer is no but I wanted to check first.
2. Is the reformat fails for whatever reason, what is likely to happen next? I intend to book a genius appointment but wondered if people had had a similar experience in the past? How long did re-servicing take? The Mac is still under the three year warranty but I am likely to have to pay anything?
Many thanks in advance.
Message was edited by: Stephen BateHello!
Good news: Today I visited the next apple partner and took my macbook with me. He checked my mac with the software "DiskWarrior" which reported three problems which could be solved with this software. Afterwards we tried to restart the macbook - no effort.
He told me, that in a probability of 90% it would be a software problem and it could be solved with re-installing the mac os X software with inserting the original disc, pushing the button "C" shortly after pushing the power-button and simply reinstalling the OS X.
It worked and as it seems no data got lost.
The mac partner dude told me that this software problem can be caused by shutting down the mac one time too much with pushing down the powerbutton more than 5 seconds when everythings freezes...
As I write from my macbook again, I proudly announce that I'm back on mac.
I used windows while having these problems; it sucked
Sincerely, aftermathentertainment
PS: What have I learnt from this: Use TimeMachine! -
My MacBook Pro, does not start after pushing start button. The side bar starts and stops at half way.
Hy myneck,
Happy Holidays! The resource below may provide some steps to try if your MacBook Pro won't start.
Troubleshooting: My computer won't turn on - Apple Support
http://support.apple.com/en-us/TS1367
This article discusses what to do if your Mac won't turn on. To differentiate this from a display issue, be sure that when you press the power button:
You don't hear a startup chime.
You don't hear any fan or drive noise.
There is no video on your built-in or external display
If your computer has power but doesn't display any video, it may have one or more of these similar symptoms when you press the power button:
You may hear a startup chime.
You may hear fan or drive noise.
You may see a light from the Sleep LED (if your Mac has one).
Pressing the Caps Lock key on the keyboard causes it to light.
If any of these display-related conditions occur, see Troubleshooting: My computer has no video instead. Otherwise, continue with this article.
If your computer won't turn on, try each of these steps:
Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
MacBook Pro: How to remove or install memory
MacBook: How to remove or install memory
Mac Pro: How to remove or install memory
Mac mini: How to remove or install memory
iMac (27-inch, Late 2012): Installing or replacing memory
iMac: How to remove or install memory
Reset the SMC.
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
I hope this information helps ....
- Judy -
My MacBook Pro won't start. It's old, c 2008, any ideas?
My MacBook Pro won't start. It's old, c 2008. Have tried many suggestions on line: opt, cmnd, r,p, etc. Any suggestions?
Hey treasure hunter,
I found some help for when your computer won't turn on. Try each of these steps:
Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.MacBook Pro: How to remove or install memory
Reset the SMC.
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).
Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
via: Troubleshooting: My computer won't turn on
http://support.apple.com/kb/TS1367
Welcome to Apple Support Communities!
Regards,
Delgadoh -
I just got to school after getting a new screen put on my 13in macbook pro. when i opend up my macbook there was only a apple simble and the loading sing with a bar at the botton it took fovere to load, one it loaded and opend up there was a few options to pic from saying i could get all my datata back, i got confused and called the tec support where they wanted me to spend 90$ to back up my data, i feel as if they fixed my screen my data should be there when i go on it. I am a broke colage studend and need to get my work done. To sum it all up How do i get all my data back that happend to get lost while my screen was being repaird at the apple store?
Apple has a 90 warranty warranty on all of their repairs. You should take your computer back to the repair shop. Or call Apple Customer Relations (800) 767-2775. Wait for a human to come on the line and ask politely and firmly that you want to be transferred over to the Customer Relations department. Tell them your issue.
pakoning wrote:
I am a broke colage studend
Hard to believe with all the typos in your post! -
In my macbook pro when composing email it coping into thrash as well so how to stop this ?
in my macbook pro when composing email it coping into thrash as well so how to stop this ?
You may have a Bad fan. Make an appointment and take it to the genius bar for an evaluation. It's free, in warranty or out.
-
I was messing around with .kext files in the MacintoshHD and now my MacBook Pro won't start up.
I was messing around with .kext files in the MacintoshHD and moved the system.kext and two others to my desktop and deleted the originals and now the MacBook Pro won't start up. All I get at start up is the apple icon then a bunch of text shows up part of which says Mac OS version: not yet set. then the apple icon turns into the power icon and tells me to turn off the computer. I've tried reinstalling from the install DVD by holding down option when powering on and selecting the install DVD and it just goes to a white screen with the apple icon and stays like that. I didn't have the disk utility on my Mac before this happened because I deleted it to make room on my computer a while ago so I'm not sure if that's why it won't load the install DVD but anyone who knows the solution to this with out going to get it repaired would be greatly appreciated. Thank you!
Never mind my dad just found the original install DVD and that worked. Before I was using an install disc that Apple sent me for another issue I was having, but thanks for replying so quickly and trying to help on this Thanksgiving day!!!
-
TS3423 17" macbook pro won't start blue file with question mark is all that appears on the screen
My old macbook pro will not start up. Worked fine yesterday, today all I gat is the startup sound and a blank blue screen. After a while the screen shows a file folder icon with a question mark in it. Any ideas
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by:
Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
Boot drive's directory has been corrupted - Repair with Disk Utility.
Critical system files are damaged or deleted - Reinstall OS X.
The disk drive is physically non-functional - Replace the hard drive.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD:
Boot From The Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
Hi! My MacBook Pro won't start! HELP !!!
Hi! My MacBook Pro won't start! I have tried everything I can think of like Safe Mode (doesn't work), Recovery (does not find Recovery Drive), Booting with OS Snow Leopard Cd (doesn't work)...
I have really no clue about what to do now... I paid quite a lot of money for this computer and am pretty short of money nowadays! Would like to repair with help rather than having to take it to Apple Store.
Has anyone had this same problem?
All I get is white screen + grey Apple and spinning grey disk... it's 100% frustrating! Any help would be more than welcome since I think i've tried EVERY SUGGESTION on this Support Center and Youtube videos...
This MBP is from 2011, runs on OS X 10.6.8
I tried booting with OS X Snow Leopard CD, it didn't work! (my cd player works! recognizes the Snow Leopard CD, but then never opens it... goes back forever to the with screen + apple and spinning disk)
I don't care about the content, it's OK if i lose all DATA... I just want to bring this Mac BACK TO LIFE!
When i run coomand on root# fsck -fy --> RESULT = my HD was checked and seems to be FINE!
ThanksPlease make a Genius Appointment and take it in for service.
Maybe you are looking for
-
I have an ipod touch and recently performed the latest updates of itunes. It said there were problems with my ipod and it need to be restored. I did that and now it says it's in recovery mode and that I need to restore it. It takes 45 minutes and
-
How do I increase the menu font size for Bible Fox?
I know how to increase page text size etc, but using (brown) Bible Fox theme, I can't increase the menu font size. Is there a way to do this?
-
How do I get my MX420 to print out a fax that is in its memory?
How do I get my MX420 to print out a fax that is in its memory?
-
Finder can't access a mounted windows share - but the Terminal can...
When I mount a drive using the finder's "Go / Connect to Server..." command I can choose the share to connect to and Finder mounts the share, puts it on the desktop etc... but then it tells me that: "The folder "Sharename" can't be opened because you
-
Error: PLS-222: no function with name 'V' exists in this scope
In my application, I used the wizard to create a form on a table with Report (2 pages). Then I go to the Report page and I want to test the edit function. This successfully launches the edit Form. When I change the values in the form and then try to