Macbook Pro Wi-Fi causes mouse lag for Logitech MX Revolution
I just got the new 15" Macbook Pro 2.4ghz on Tuesday, October 28th. Yesterday, I tried using my Logitech MX Revolution mouse with it only to discover that it was nearly unusable. The cursor would lag terribly, sometimes sticking in one spot for several seconds and it was often not registering mouse clicks or scrolling. I tried it on my old Powerbook G4 that I had been using it on without issue for over a year. It had the same issue all of a sudden so I tried it on my co-workers 2007 Macbook Pro, he works across the office from me, and the mouse worked perfectly again. Next, I brought my old Powerbook over to his desk to see if there was some interference at my desk, and sure enough, it worked on that Powerbook again. So I then tried disabling the wifi on my new mac and lo and behold, the mouse worked perfectly on that machine.
I've tried switching the channel on our office router (it's a 1TB Time Capsule) a few times and that would help for a few seconds, and then the mouse lag would begin again. I doubt there's a way to change the frequency on the Macbook's wifi card, but if there is let me know. Beyond that, I'm not sure what to do. I will be a little upset if this mouse (which cost me $100) is obsolete because of my Macbook upgrade. There must be a way to get it working again. Ideas? Thanks!
Hi,
I use a new 2,53ghz Macbook Pro togeter with a MX Revolution mouse. I use 2 Airport Extreme base stations in my w-lan and until now see no issues using the mouse.
Do you have the chance to try and check if the same promlem occuors when using an other MX Revolution / receiver combo , maybe there is an issue there.
Similar Messages
-
my macbook pro is frozen, the mouse moves, but it will not click. I have restarted and it is still the same... Can anyone help me ?
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test. -
When trying to Airplay from my Macbook Pro Retina, to AppleTv3 it plays for only a few minutes, and then jumps back to the Mac. It seems to do this no matter what I play, music, movies or pictures. I just bought a new router. This could affect it.
I have been playing whole movies before from VLC without problems.
Any Ideas?Welcome to the Apple Community.
Yes it's network issues or settings that cause these types of problems most of the time.
The following article(s) may help you.
Troubleshooting AirPlay
Troubleshooting Wi-Fi networks and connections
Recommended Wi-Fi settings
Wifi Diagnostic Software (for Mac users)
You may also find some help on this page, where I’ve collected some of the more unusual solutions to network issues. -
I have a macbook pro mc700, And the scrolling lags or doesn't respond at times. What can I do to fix it?
There is excessive swapping of data between physical memory and virtual memory.
That can happen for two reasons:
You have a long-running process with a memory leak (i.e., a bug), or
You don't have enough memory installed for your usage pattern.
Tracking down a memory leak can be difficult, and it may come down to a process of elimination.
In the Activity Monitor application, select All Processes from the menu in the toolbar, if not already selected. Click the heading of the Real Mem column in the process table twice to sort the table with the highest value at the top. If you don't see that column, select
View ▹ Columns ▹ Real Memory
from the menu bar.
If one process (excluding "kernel_task") is using much more memory than all the others, that could be an indication of a leak. A better indication would be a process that continually grabs more and more real memory over time without ever releasing it. Here is an example of how it's done.
The process named "Safari Web Content" renders web pages for Safari and other applications. It uses a lot of memory and may leak if certain Safari extensions or third-party web plugins are installed. Consider it a prime suspect.
If you don't have an obvious memory leak, your options are to install more memory (if possible) or to run fewer programs simultaneously.
The next suggestion is only for users familiar with the shell. For a more precise, but potentially misleading, test, run the following command:
sudo leaks -nocontext -nostacks process | grep total
where process is the name of a process you suspect of leaking memory. Almost every process will leak some memory; the question is how much, and especially how much the leak increases with time. I can’t be more specific. See the leaks(1) man page and the Apple developer documentation for details. -
How do I use my Macbook pro retina display as a monitor for a PC?
How do I use my Macbook pro retina display as a monitor for a PC?
MacQueries wrote:
How do I use my Macbook pro retina display as a monitor for a PC?
Unfortunately, that is not possible. The computer only can "output" your display image, it cannot "input" an image from an external computer and display it on your MacBook's retina display. -
I have an early 2011 MacBook Pro which has been running slow for a while. After looking at responses to similar problems I have downloaded and run EtreCheck. Please can someone help me with what it all means.
Thanks in advance.
EtreCheck version: 1.9.15 (52)
Report generated 19 September 2014 08:07:14 GMT+8
Hardware Information: ?
MacBook Pro (13-inch, Early 2011) (Verified)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2 cores
4 GB RAM
Video Information: ?
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ?
OS X 10.9.4 (13E28) - Uptime: 0 days 0:4:29
Disk Information: ?
Hitachi HTS545032B9A302 disk0 : (320.07 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted>: 209.7 MB
Macintosh HD (disk0s2) / [Startup]: 319.21 GB (147 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
MATSHITADVD-R UJ-898
USB Information: ?
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ?
Apple Inc. thunderbolt_bus
Gatekeeper: ?
Mac App Store and identified developers
Kernel Extensions: ?
[not loaded] com.seagate.driver.PowSecDriverCore (5.2.4 - SDK 10.4) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_4 (5.2.4 - SDK 10.4) Support
[not loaded] com.seagate.driver.PowSecLeafDriver_10_5 (5.2.4 - SDK 10.5) Support
[not loaded] com.seagate.driver.SeagateDriveIcons (5.2.4 - SDK 10.4) Support
[loaded] com.sophos.kext.sav (9.1.55 - SDK 10.7) Support
[loaded] com.sophos.nke.swi (9.1.50 - SDK 10.8) Support
Launch Daemons: ?
[loaded] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[running] com.sophos.autoupdate.plist Support
[running] com.sophos.configuration.plist Support
[running] com.sophos.intercheck.plist Support
[running] com.sophos.notification.plist Support
[running] com.sophos.scan.plist Support
[running] com.sophos.sxld.plist Support
[running] com.sophos.webd.plist Support
[running] com.trusteer.rooks.rooksd.plist Support
Launch Agents: ?
[loaded] com.divx.dms.agent.plist Support
[loaded] com.divx.update.agent.plist Support
[running] com.sophos.uiserver.plist Support
[running] com.trusteer.rapport.rapportd.plist Support
User Launch Agents: ?
[loaded] com.adobe.ARM.[...].plist Support
[running] com.amazon.music.plist Support
[loaded] com.google.keystone.agent.plist Support
[not loaded] jp.co.canon.Inkjet_Extended_Survey_Agent.plist Support
User Login Items: ?
iTunesHelper
TomTomHOMERunner
AdobeResourceSynchronizer
Dropbox
Internet Plug-ins: ?
FlashPlayer-10.6: Version: 15.0.0.152 - SDK 10.6 Support
DivX Web Player: Version: 3.2.1.977 - SDK 10.6 Support
AdobePDFViewerNPAPI: Version: 11.0.09 - SDK 10.6 Support
AdobePDFViewer: Version: 11.0.09 - SDK 10.6 Support
Flash Player: Version: 15.0.0.152 - SDK 10.6 Support
EPPEX Plugin: Version: 10.0 Support
Default Browser: Version: 537 - SDK 10.9
OVSHelper: Version: 1.1 Support
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.4.4 - SDK 10.6 Support
iPhotoPhotocast: Version: 7.0 - SDK 10.7
Safari Extensions: ?
Ultimate
Audio Plug-ins: ?
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 2.0 - SDK 10.9
AppleAVBAudio: Version: 203.2 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
iTunes Plug-ins: ?
Quartz Composer Visualizer: Version: 1.4 - SDK 10.9
3rd Party Preference Panes: ?
Flash Player Support
Perian Support
Trusteer Endpoint Protection Support
Time Machine: ?
Skip System Files: NO
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 297.29 GB Disk used: 160.38 GB
Destinations:
Data [Network] (Last used)
Total size: 2 TB
Total number of backups: 99
Oldest backup: 2012-04-20 17:05:32 +0000
Last backup: 2014-09-18 23:49:25 +0000
Size of backup disk: Excellent
Backup size 2 TB > (Disk size 297.29 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU: ?
6% InterCheck
5% iCalExternalSync
3% WindowServer
2% CalendarAgent
2% SystemUIServer
Top Processes by Memory: ?
152 MB SophosScanD
147 MB InterCheck
106 MB SophosAntiVirus
66 MB Dropbox
57 MB com.apple.iTunesLibraryService
Virtual Memory Information: ?
161 MB Free RAM
1.55 GB Active RAM
1.41 GB Inactive RAM
902 MB Wired RAM
611 MB Page-ins
0 B Page-outsUninstall Trusteer software
http://www.trusteer.com/support/uninstalling-rapport-mac-os-x
Remove Sophos
https://discussions.apple.com/message/21069437#21069437 -
I just created a new profile/user on my MacBook Pro. My pointer/mouse on my trackpad. It works fine in my older user profile, but when I go to the new profile my mac will not respond to clicks. The Mouse moves but will not click. Already tried restarting and the pram zap. The problem starts when I log out of my main profile. I get to the login screen and my laptop stops responding to clicks. When I manage to make my way back to my main profile the mouse works perfectly. Should I just delete the new profile and try again?
If the modem is also a router, either use the modem in bridge and run pppoe client on the TC.. that is assuming ADSL or similar eg vdsl. If it is cable service.. and the modem is a router, then bridge the TC.. go to internet page and select connect by ethernet and below that set connection sharing to bridge.
Please tell us more about the modem if the above gives you issues. -
Cannot get iPad 2 charged beyond 1%. All charging ports tried: AC adapter(s), USB 2 port on MacBook Pro. ITunes shows iPad only for a few seconds. iPad displays alternately: Apple logo, battery w/slim red band, then battery w/1% charged information. How can I get it to charge beyond 1% so I can proceed to troubleshoot?
I have had your exact problem with my old 3GS, now I cannot even get it to turn on, I still see that it is supposed to be charging though, but it never charges any so it seems.
I replaced the Lower Dock Connector Assembly back when it still charged while hooked to my PC, and it found it made no real difference.
http://www.amazon.com/gp/product/B003Y5YXLK/ref=oh_details_o05_s00_i00?ie=UTF8&p sc=1
At this point I am not sure if I should replace the battery and hope for the best, or just junk the phone, I cannot really sell it if I cannot reset it... -
I have just transferred my iTunes library from a hard drive previously connected to a windows laptop to a MacBook Pro and now all my options for editing info are greyed out. I have seen the answers if still using windows but could find a similar situation to this one.
Eels290776 wrote:
if my external hard drive is not connected to either of my machines, and I download something onto my iMac and then something different onto my Macbook, where are my machines going to be storing the new downloaded media
when the drive is not connected, +iTunes media folder location+ will default back to <MacintoshHD>/users/<yourname>/music/iTunes/iTunes music (or media)
and when I next connect the external hard drive how will I easily get the newly downloaded media onto the external HD
you'd have to point +iTunes media folder location+ back to the external via preferences > advanced > iTunes media folder location, then file > library, organize library > consolidate files
and essentially, to have it easily readable on both machines?
in that case it might be best to copy the entire iTunes folder to the external. then, on each machine, launch iTunes while pressing option on your keyboard. when prompted, click on +choose library+ and navigate to the iTunes folder on the external.
note only one iTunes can access the iTunes library @ a time !
also, make sure the external is mounted on either machine before launching iTunes.
JGG -
How do I stop the indexing on my MacBook Pro? It's been indexing for 2 days.
How do I stop the indexing on my MacBook Pro? It's been indexing for 2 days.
Step 1
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Triple-click anywhere in the line below on this page to select it:
syslog -F '$Time $Message' -k Sender mdworker -o -k Message Rne Norm -k Sender mds | tail | pbcopy
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Paste into the Terminal window by pressing the key combination command-V. I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign ($) to appear.
The output of the command will be automatically copied to the Clipboard. If the command produced no output, the Clipboard will be empty. Paste into a reply to this message.
The Terminal window doesn't show the output. Please don't copy anything from there.
If any personal information appears in the output, anonymize before posting, but don’t remove the context.
Step 2
Enter the following command as in Step 1 and post the output:
mdutil -as 2>&- | pbcopy
You can then quit Terminal.
Step 3
Launch the Console application in the same way you launched Terminal. In the Console window, look under the heading DIAGNOSTIC AND USAGE INFORMATION on the left for crash reports related to Spotlight. If you don't see that heading, select
View ▹ Show Log List
from the menu bar. A Spotlight crash report has a name beginning in "mds" or "mdworker" and ending in ".crash". Select the most recent such report, if any, from the System and User subcategories and post the entire contents—the text, please, not a screenshot. In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post any other kind of diagnostic report, such as hang logs—they're very long and not helpful. -
i kept a dual boot of windows 7 and mac os x lion in macbook pro. so, should i keep antivirus for windows 7? which is prescribable between bit defender(bd) and microsoft security essentials(mse)?does bd and mse un-installs easily?
lower your font size unless you have difficulty
MS Security Essentials is excellent
Then again maybe time to investigate Windows 8 RP (which uses Defender) -
HT3211 Should we press to click on something in macbook pro ? Mine is not touch for clicking !!
Should we press to click on something in macbook pro ? Mine is not touch for clicking !! I mean i must push the trackpad to click but for other functions it is touch and it doesnt need to be pushed ! Is it broken ?
Not necessarily. Do you have Tap to Click turned on?
-
have a macbook pro, looking at getting an iMac for home, can i share files easily i.e through a thunderbolt cable? dont want to use dropbox as it will take too long, need direct access to my macbook via the imac
Assuming you have a wireless network at home, just use file sharing. System Preferences / Sharing. Choose a folder you want to share and you're done.
-
Can I take my new MacBook Pro retina to an apple store for them to transfer files
Can I take my new MacBook Pro retina to an apple store for them to transfer files from my PC? I am migrating from window 7. I was planning on doing myself but it looks like you need two thunderbolt to Ethernet adapters and two Ethernet cables? What is the best way to transfer? I live in a rural area and think maybe wirelessly may not be the best way? Thanks for any assistance!
Can I use my back up from my PC to transfer? I just backed up my PC to WD My Book. Will that work?
Probably will work fine. It's worth a try and won't do any harm.
http://support.apple.com/kb/ht2518
What you can transfer to your Mac depends on the files.
Photo files (.jpg .tiff etc) fine
Music files - some may need conversion software to be used in iTunes (unless you had iTunes on your PC) but free converters are there
Video files - ditto, some will work in iMovie, others may need converting to work
Text - Pages will read .doc and .docx files. Most Word processing files/spreadsheet files/presentation files can be read in iWork but if not, can use Open Office or Libre Office (both free downloads)
Windows programs (eg those with a .exe suffix) won't work on a Mac without installing Windows (e.g. via BootCamp). -
I'm having trouble with my macbook pro, I have only had it for three months, when I plugged a camera sd card into the sd slot it isn't appearing anywhere on the computer and i can not access my photographs. can somebody please help me?
Shootist007 wrote:
Clifton I must disagree with you on the above statement. It is my opinion and experience that you should never connect the camera directly to any computer, Mac Windows Whatever.
It is always best to Remove the memory card from the camera and put it in a card reader, whether an external reader or one built into the computer, to copy images from the card.
Hi Shootist. I would be interested in hearing some reasoning on this. I almost always use a USB cable to connect my camera to the MBP for transferring pictures, and have moved about 30,000 this way over the last 6 years since my photography went digital. Recently, on the rare occassions when I have only a few to transfer and I was too lazy to go for the cable, I have used the card reader; about half those times I have difficulty getting the MBP to recognise the card. I find I have to press the card very hard into the slot for it to be recognised.
My rationale is quite possibly wrong, but I feel that the USB connectors are more robust and hard-wearing than the flimsy connectors on an SD card. Also, I haven't measured it, but I think the data transfer is faster with the cable. (I just came across this test, which reports noticeably faster transfer for cable than built-in card reader, but the computer was a PC)
Chiara, sorry for hijacking your thread.
Maybe you are looking for
-
Restore Time Machine backup on fresh Leopard install without disc.
I just got my iMac back from the Apple Store where they fitted a new hard drive with a fresh installation of Leopard. I've got an external drive with a Time Machine backup of my old HD, but don't know how to restore it. Unfortunately I forgot to ask
-
Hi All, I have to configure the scenario to send the data from r/3 to webservice . Receiver side we need to send a JMS message. How can we send the JMS messages to webserver as we have to use SOAP/HTTP adapter to communicate with webservices. Any on
-
Open yahoo and click the News tab in IE, and do the same for Firefox. IE displays real news but Fire fox is now displaying a watered down news and absolutely nothing of a controversial nature.
-
Displaying parameter form in Portal
we have reports created using 9i reports builder and are running them using 9ias portal version 9.0.2.2.22 can we get the parameter form displaying before the report is run, as at the moment it either gives an error because parameters have not been e
-
Weblogic apache plugin and webservices
Can I use the weblogic plugin on a DMZ based Apache server and use a 3 tier architecture to implement webservices. Using this model can a external application contact my webservices running in my internal network and can my weblogic/webservices serve