Macbook Pro will not boot up normally Not Normal Problems

Ok. I have an older 17" Macbook pro 2.33 (10.6 fully updated) that will not boot up in normal mode. When I boot it shows "blocks" of different colors and will not get past the blue screen sometimes. When it does get passed the the blue or grey screen it is a split screen of white back ground with large black blocks seperating the sides. I have tried swapping out harddrives with a known working one with an OSX image on it-no good. I have tried swapping out ram-same thing. I reset the SMC and PRAM-only colors changed in the blocks. I have ran disk utilites disk and permisions with no problems. I can't boot into a restore disk using the c key during boot, It locks up at the same screen. Nothing works except safe mode. I can boot into safe mode and everything works just fine with normal screen and all. Now I tried runing the Lion installer thinking it is and driver issue but I can't get Lion to boot to the hard drive and Snow leopard just reboots back to the same screen. So how can I get Lion to install or Snow Leopard?
What can I do? I noticed this last weekend when I tried to reboot my MB Pro and it started this. Well Apple pushed and update last friday - I needed to restart it again and this happends. I thought it was a logic board at fist until it booted fine in safe mode.

Sorry. What I mean is I selected the SL boot up in the start up panel and it would not boot into the cd. The CD rom sounds like it just keeps reading with it slowly loading from grey screen to blue screen to the Block screen. Almost like it is booting into normal mode from the hard drive.
What I can't understand is why it runs fine is Safe mode?
Also why do I get a " this disk cannot be used to start up your computer" message on my hard drive when trying to install Lion in safe mode? Well why not it's the only hard drive in the computer?
The first screen shot is the Tech tool showing everything passed the hardware test is safe mode.

Similar Messages

Macbook Pro Will 'Tap to Click' but not 'Normally Click'

Hello, my Macbook Pro is not allowing me to click at all now. I can only 'Tap to Click' but when i physically press down on the Touchpad, the Mac doesn't accept it.
I don't know what i should do.
Is my only option to take it to the Genius Bar?
Thanks,
--André

Hi,
I think I have the same issue (new mbpro 15'' jan 2009), the normal "physical" click behaves very strangely, sometimes works sporadically, then doesn't work anymore at all. I had to enable the "tap to click" in order to be able to click :/
I can remember there was a firmware update at the very beginning for this glass trackpad because of those missing clicks and it seemed to be solved. But now, several months after, this seems to be worst than before: I sometimes enter this state with no physical click at all !
André, could you please keep us informed about the feedback you get from Apple if any ? Thanks a lot (I keep on trying finding something about it on the web but unfortunatly I always get articles from Nov 2008 about the 1st missing click issue that leaded to the firmware update... :/)

Macbook Pro won't boot up, recovery not working

A few days ago my macbook pro crashed. it was being unresponsive for about 5 minutes so i turned it off and on again (ive done this a lot). except this time when i went to turn it back on i saw the grey folder with a question mark on it. i looked a lot into what to do but am currently stuck because i have tried everything ive seen and nothing has worked.
i went into internet recovery holding option when starting up because internet recovery was the only option it provided.
i have tried to install a new copy of OSX but when i get to the screen where it asks where i want to install it to, there are no locations for me to chose from.
i have tried going into disk utility but it doesnt give me the option to select my main disk, only the recovery one it just downloaded.
it seems that the computer is completely disconnected from the operating system.
I believe the problem might have something to do with me going a long time without updating software (i know it's stupid but i have a hatred for constant updates when the version i use works just fine)
I need to keep my files from this computer, it is absolutely crucial that my hard drive is not wiped.
is there a way to back up my files from this stage? i don't have a backup from before it crashed (sorry for not expecting my computer to just fail on me)
I have had this computer for less than a year.
so the main thing I need is to recover my files, even if it requires physically taking the hard drive out of the laptop to recover them on another computer.
any help is appreciated, thanks.
(p.s. I forget exactly which OS it was on, but i believe it was Mavericks, not sure which version of it)

The symptoms that you are describing indicate that your internal HDD has died. Your data may be lost or require professional recovery services to retrieve.
Enter the serial number (on the bottom) of your MBP here and post back the model information:
https://selfsolve.apple.com/agreementWarrantyDynamic.do
Ciao.

My macbook pro will only boot in safe mode

Hey,
I have a macbook pro 15-inch, Early 2011 running osx 10.9.4. I have a SSD hard drive that i installed myself a year ago and hasn't shown any defects. Its a 120 gb OCZ-AGILITY3.
My problem:
My macbook will only boot in safe mode nowadays. I have done a complete erasion of my hard drive and installed osx mavericks twice already. After the installation the computer will safely go to the desktop. But if i then do a reboot it won't get further than after the first apple logo, sometime the turning wheel will pop up, before turning off and trying again. i have tried resetting PRAM, I have tried resetting SMC, i have tried avoiding SMC (with big fan rate), but all with no success.
I have done a complete hardware test (the longer one) and it showed "no troubles found".
My guess is that the problem is with the battery. My computer won't run anymore without the adapter, when i pull the adapter out it either stays on for a while before just turning off. Without having it plugged in it won't start. Is it possible that during normal start up there is some kind of communication with the battery that can cause this?
I ran a diagnostic shown in this thread (Will only boot in safe mode) and included it in this post.
Hope someone can help me out.
Thanks,
Bram
Start time: 17:07:42 08/25/14
Model Identifier: MacBookPro8,2
System Version: OS X 10.9.4 (13E28)
Kernel Version: Darwin 13.3.0
Boot Mode: Safe
Time since boot: 10 minutes
Battery
Condition: Replace Now
Diagnostic reports
2014-08-25 UserEventAgent crash
Log
Aug 26 00:41:52 Previous Shutdown Cause: -128
Aug 25 16:23:38 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:24:05 process rpcsvchost[94] thread 917 caught burning CPU! It used more than 50% CPU (Actual recent usage: 99%) over 180 seconds. thread lifetime cpu usage 100.014147 seconds, (82.533432 user, 17.480715 system) ledger info: balance: 90006319931 credit: 100003230498 debit: 9996910567 limit: 90000000000 (50%) period: 180000000000 time since last refill (ns): 90079246240
Aug 25 16:25:50 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): examining extra transactions starting @ 9773056 / 0x952000
Aug 25 16:58:05 jnl: b(1, 3): txn starting at 9773056 (9773056) @ index 80 bnum 2696544 (8192) with disk cksum != blhdr cksum (0x93b69228 0xc647562)
Aug 25 16:58:05 jnl: 0x662b0000 0x451b0000 0x2a0001ff 0x40000000 0xd7330300 0x46001d00 0x6c006f00 0x65006400
Aug 25 16:58:05 jnl: b(1, 3): restarting journal replay (9340928 - 9773056)!
Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
Aug 25 16:58:05 jnl: b(1, 3): journal replay done.
Aug 25 16:58:06 Previous Shutdown Cause: -128
Aug 25 16:59:26 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Aug 25 16:59:59 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
Activity
CPU: user 17%, system 4%
CPU per process: WindowServer (UID 0) is using 30.5 %
launchd
/System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist
- com.apple.AirPortBaseStationAgent
Contents of /System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist (XML document text)
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Label</key>
<string>com.apple.AirPortBaseStationAgent</string>
<key>EnableTransactions</key>
<true/>
<key>LowPriorityIO</key>
<true/>
<key>LimitLoadToSessionType</key>
<string>Aqua</string>
<key>POSIXSpawnType</key>
<string>Background</string>
<key>LaunchEvents</key>
<dict>
<key>com.apple.distnoted.matching</key>
<dict>
<key>com.apple.airport.agent.prefschanged</key>
<dict>
<key>Name</key>
<string>com.apple.airport.agent</string>
</dict>
</dict>
<key>com.apple.bonjour.events</key>
...and 21 more line(s)
Spotlight: Indexing and searching disabled
Font issues: 11
Wi-Fi
link auth: wpa-psk
Restricted files: 1
Elapsed time (s): 278

Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

Macbook pro will no longer boot from main sata bay after Yosemite

Hi!
I am really stuck as to why my macbook pro will no boot from the main Sata bay.
I have the macbook pro late 2011 - a few months ago I installed a samsung 840 evo, and moved the 500gb hdd into the optical bay and all has been working perfectly until last night.
I installed yosemite two days ago and it worked perfectly to begin with... then when I re opened my laptop everything was frozen. I restarted it and it wouldnt get past the grey screen. Then I managed to get it to the internet recovery stage....however it would not recognise the SSD, so I had to install Lion on the HDD.
After I logged on it gave me the message saying that the disc is not readable and on disk utility I can only see the "samsung ssd" but no details about it.
I thought that the SSD may have gone, but when i removed it and plugged it in via USB I was able to boot from it with no issues.
Does anyone know if this has anything to do with the new OS? or whether it is the Sata cable?
Thanks for any help!!!

Hi, I have been having the exact same problem with a late 2011 MBP 15 inch. I replaced the hard drive with a samsung SSD 1.5 years ago, along with a samsung SSD in the optical drive. It worked great until the Yosemite upgrade. The MBP seemed to work reasonably well for a few days after the upgrade, but then it started stalling on various programs (spinning beach ball on Mail, Safari, etc). Start-ups were also longer and had a loading bar each time, which was new since the upgrade. I left the MBP to sleep last night and when opening it, it crashed and tried to restart. On restart it loads to the login screen, then after I enter the password it partially loads (based on the loading bar), then shuts off. I removed the SSD and plugged it in with a USG, but that didn't change anything. Here is a picture after using CMD-V before it shuts off.

MacBook Pro will not boot up. Hardware test found no problems.

MacBook Pro will not boot up. Hardware test found no problems.

Sorry. What I mean is I selected the SL boot up in the start up panel and it would not boot into the cd. The CD rom sounds like it just keeps reading with it slowly loading from grey screen to blue screen to the Block screen. Almost like it is booting into normal mode from the hard drive.
What I can't understand is why it runs fine is Safe mode?
Also why do I get a " this disk cannot be used to start up your computer" message on my hard drive when trying to install Lion in safe mode? Well why not it's the only hard drive in the computer?
The first screen shot is the Tech tool showing everything passed the hardware test is safe mode.

MacBook pro will not boot. I get the gray screen, an apple icon and spinning wheel. Tried to start in safe mode but get the same screen. The only thing different was that I loaded the zedge sync app yesterday. Now getting this problem.

Macbook pro will not boot. I get the gray screen, an apple icon and spinning wheel. I tried to start in safe mode, but get this same screen. The only thing different is that I added the zedge update app to do a sync for adding ringtones to my apple cell phone. How can I get a good boot. I am fairly new to apple computer.

Reset PRAM: http://support.apple.com/kb/PH4405 and then try a normal boot.
Run the Startup Manager to select Startup disk: http://support.apple.com/kb/HT1310
If those did not work your disk may be sick or dying. The top priority at this point is to make a backup copy of your data.
Check the health of the disk. Boot in Recovery Mode (Boot, Command-R). Run Disk Utility. Click on the upper left disk icon. Does the S.M.A.R.T. status say “Verified”? If not the disk/SSD is unhealthy and needs to be replaced. Even if it does not show “Verified” you can still attempt a backup.
Click on the icon indented below, usually called “Macintosh HD” and Verify Disk. If it finishes with a green “OK” message then all is well with the disk. If it shows errors in red then you have found a problem to address once the system is backed up. Do not attempt software repairs until you have secured the data.
If the disk will not show up at all in Disk Utility as your ran the tests above then it may be dead or it may have a bad internal SATA cable. A trip to an Apple store for confirmation would be in order.
If you have an external disk drive you can use as a backup drive then do so. If not Google “Hitachi USB 3.0 external hard drive 1TB” to purchase one or go to a brick-and-mortar store (including an Apple store) to pickup one. Any 1 TB external drive will do.
Assuming it is still breathing you can try to recover the data without booting from the sick disk.
Reformat the external disk. (This will erase all data on the external disk.)
Boot in Recovery Mode. Start Disk Utility. Plug in the new disk. Select it’s disk Icon (the second one down, left justified). Select the Partition tab.
Partition Layout > Single Partition
Name: Emergency Recovery 1 (or whatever name you wish to use)
Format: Mac OS Extended (journaled)
Options… > GUID Partition Table > OK
Apply
Select the Restore tab.
Drag the old system volume (Macintosh HD) to Source.
Drag the new disk volume (Emergency Recovery 1) to Destination.
Click on Restore.
It may take a long time for the backup.
If that will not complete post back for other emergency data recovery methods, including those from a brody.
If the backup succeeds, use the First Aid tab in Disk Utility to select the old volume (Macintosh HD) and Repair Disk. If it does not finish with a green OK message try to repair it once or twice more. If it repairs with a green OK message, will it boot normally? If not, boot from the Recovery Partition and reinstall OS X.
If it is still not healthy, post back for further instructions.

Macbook PRo will not boot, MagSafe adaptor light does not work !

Okay... so i have this issue with my MBP where it will not power up.
The light on the magsafe does not show up at all when connected to the MBP. I have tried another magsafe but failed. I have not tried another battery so im not sure if that is wheret the fault lies.
Ive tried the SMC reset holding the power button down for long, but still no result. However, i left the MBP disconnected from the magsafe and went out for the whole day. Came back, connected the magsafe and thought id try again. I held the power button for 10 seconds and the MBP started booting. It wasnt the normal boot im not sure if it was performing some sort of safe boot, but it was doing something, the screen turned transparent white, restarted and i could finally log in. The battery was very low so i left it on charge with magsafe.
One thing i have noticed is that sometimes i wont get the light showing on the magsafe but it may still be charging at that point.
This morning i wake up and its the same issue all over again. It must have stopped charging or something as i left the MBP on with magsafe connected. Now it will not turn on no matter what i do.
If i tilt the magsafe connector at an angle i can see a dim green light but then id have to hold it in that place to see that light.
Please advise on what i should do next. Excuse the long story !

Hi s.cheslik,
It seems your MacBook Pro will not boot properly and it displaying an error message. Based on the information you have provided, it appears your MacBook Pro needs to be serviced. The following link should help you get started with the process and has links with additional information on topics such as warranty and service pricing, battery replacement, and express replacement service.
Apple - Support - Service Answer Center
Thank you for contributing to Apple Support Communities.
Take care,
Bobby_D

My Mid 2010 MacBook Pro will not boot

My Mid 2010 MacBook Pro will not boot regularly, in safe mode, in recovery mode or from original OS DVD. Is this the logic board?
I've tried resetting the SMC and pram numerous times and even tried switching out hdd's to try and do a clean install on a new hdd.
If I attempt to boot regularly or from recovery drive the grey apple logo appears for a period before the screen goes black and the power LED operates as though in 'sleep' mode. I'm unable to wake it from this state and the same applies to booting in safe mode.
When attempting to boot from the OS DVD that was originally packed with the computer it just freezes on the language select option, this occurs with the other hdd's I have attempted to use.
Any other suggestions to get it working? I fear the logic board has gone and that the repair won't be worth the money.
Thank you in advance.

Hi JRC8.8,
It sounds like you have been on the right track in trying to troubleshoot this issue. You may want to see if your MacBook Pro will boot directly to the Apple Hardware Test, as outlined in the following article:
Apple Support: Using Apple Hardware Test
http://support.apple.com/kb/ht1509
Regards,
- Brenden

Macbook Pro Will Not Boot Windows Disk

I have a late 08 (or early 09) Unibody Macbook Pro 2.53Ghz. I start the Bootcamp Assistant and successfully create my Windows partition. When I restart with the Windows 7 disk, I get a blinking cursor for 1 second then it goes to a black screen and never leaves. I have tried several different Windows 7 disks with the same result. I have even tried booting from a Windows Vista, Windows XP and even a Ubuntu disk all with the same result, stuck at a black screen.
I took the hard drive out of this mac and put it into my wife's older Macbook pro, and it booted off the Windows 7 disk and completed the install to the drive with no issues. I then put the hard drive back into my Macbook Pro and get the same black screen when trying to start the Windows partition, and still have the same problem that it will not boot from any other OS disk be it Windows or Ubuntu. It boots from OS X DVDs without a problem.
Also several months ago I had a Windows XP installation on this computer with no issues. I wiped it just before going to Snow Leopard.
Any clue as to what is going on here?

What is really odd is if I take my hard drive out of my Unibody Macbook Pro and put it into my wife's non-unibody Macbook Pro, it boots the Windows partition with no problem (Remembering I previously swapped these hard drives to complete the Windows installation to my hard drive). Seeing as the disk boots on her machine fine and not in mine, and my Windows cds (DVDs) boot fine on hers and not on mine, it seems to me it's something specific about my machine, but I can't imagine what it is.

Macbook Pro will not boot beyond grey screen. System freezes.

My Macbook Pro will not boot-up or get beyond the grey screen (with spinning gear wheel.) I've tried all the recommended actions: resetting PRAM, disk repair, permissions repair, re-boot in safe mode etc but still the problem persists. When viewing the safe-boot in verbose mode, the system seems to hang at the stage when it's checking the Airport & Ethernet - the last line on the page reads: "AppleBCOM5701Ethernet: 0 0 setFixedSpeed - logic error, speed any?"
Any ideas how to fix this without doing an Archive & Install?
I'm assuming that if I do an "Archive & Install" then I will lose all my Applications (VLC, Handbrake, MS Office for Mac etc.) Will this actually be the case? Will I lose them.
Any help gratefully received. Many thanks.

jfromplymouth wrote: ...I'm assuming that if I do an "Archive & Install" then I will lose all my Applications (VLC, Handbrake, MS Office for Mac etc.) Will this actually be the case? Will I lose them...
Archive and Install just affects the System files, so any apps you have should still be available afterwards. The Installer on the disk that came with your Mac, when you bought it, will tell you this before you proceed. Of course, you can always back out of the Installer if you feel chicken.
Notwithstanding it is still necessary to backup everything. You need to check that Time Machine is set to also backup your Applications folder. It might be set not to do this.
It may not be necessary to worry about this if you have the original installer disc(s). I think any stuff downloaded from iTunes etc can be re-downloaded. However, it's probably quicker to get Time Machine to backup your apps if you can afford the HDD space. It's bound to be quicker than re-downloading the stuff plus any updates. And of course there's those Apps that you have but forgotten about. What about them?

MacBook Pro will not boot

MacBook Pro will not boot. Just get grey screen. When I hold down control + R, I get blank blue screen.

Which model MacBook Pro do you have?
It's COMMAND and R that will take you to your Recovery partion, not Control and R.
If a later model, can you boot into Internet Recovery (booting whilst holding down the command, option and R keys)?
Clinton

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

How do I uninstall Yosemite please ? Since I upgraded my 2011 MacBook Pro will not boot up

My 2011 MacBook Pro will not boot up following my upgrade to Yosemite. How do I uninstall or downgrade back to the previous version of OS please ?

You can't downgrade or uninstall unless you first erase the drive. Try the following:
Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

HT4718 I recently upgrade my OS and now my MacBook Pro will not boot up

I recently upgrade my OS and now my MacBook Pro will not boot up

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

HT3964 My MacBook Pro will not boot up. The screen remains dark although the the comput makes the characteristic start up sound. The sleep light is showing.

MY MacBook Pro will not boot upThe screen is dark, but the sleep light is on and it makes the characteristic start up sound.What is wrong?

There is always the forum for MBP
MacBook Pro
https://discussions.apple.com/community/notebooks/macbook_pro
https://discussions.apple.com/community/mac_os?view=discussions
http://www.apple.com/support/macbookpro

Macbook Pro will not boot up normally ***Not Normal Problems***

Similar Messages

Maybe you are looking for

Macbook Pro will not boot up normally Not Normal Problems