MacBook Pro won't boot after 10.6.8 update.

I completely erased my hard drive, reinstalled Snow Leopard and updated to 10.6.7. I then performed an Apple Hardware Test and verified the disk using disk utility. Both tests were successful. I then updated to 10.6.8 using the combo update and restarted my MacBook Pro. The boot process ran fine until the system locked up on the bright blue screen. No peripherals were connected to the laptop during this process. I powered the laptop down using the power button and turned it on again. This time, I entered verbose mode. The last line of text that I see before the screen turns black is "[ PCI configuration begin ]". Can anyone assist me with this issue?
My System Profile is as follows.
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro3,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          4 MB
Memory:          3 GB
Bus Speed:          800 MHz
Boot ROM Version:          MBP31.0070.B07
SMC Version (system):          1.16f11
Serial Number (system):          System Serial#
Hardware UUID:          00000000-0000-1000-8000-001B639863A4
Sudden Motion Sensor:
State:          Enabled

Might be time to replace the PRAM battery. That's not the normally accessible battery, but it is one that often fails after 4 years.

Similar Messages

Macbook pro won't boot after installing update 10.9.3

macbook pro won't boot after installing update 10.9.3

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear.

MacBook Pro won't boot after trying to install 10.7.3 update. Start up stalls at Apple logo and spinning gear. Computer won't even start in safe mode.

My daughter's MacBook Pro was doing exactly the same thing. I don't know if it had anything to do with the latest update. She called me about a week ago saying that her MacBook began running slower by the day . She then called me Friday and told me that it wouldn't get past the gray screen and the gear just kept on spinning. I did everything I could over the phone including Safe mode which it wouldn't go into and thought maybe it was the hard drive. She took it to the Apple store. Originally, they also thought it was the hard drive. It ended up being a corrupted operating system (Lion). Apple genius simply re-installed Lion and she's back up and running. Good thing she backed up right before it crapped out. She'll be restoring everything tonight. Don't know if re-installing Lion will help your situation, but it did the trick for my daughter.

MacBook Pro Won't Boot after Firmware Update

So I just upgraded to a MacBook Pro which came in the mail yesterday. I removed the Apple-installed HD and swapped it out for a bigger, faster HD. I installed OS X from scratch, imported everything from my Time Machine backup during the Setup Assistant, and then started installing updates. Everything was running swimmingly until the last updates.
What happened is when I rebooted my MacBook Pro and logged in after a series of updates, I got presented with both a Bluetooth update and a Firmware update at the same time. Both required a restart so I thought I would kill two birds with one stone. I installed the Bluetooth update, and then when it asked to reset I installed the Firmware update instead. However, the firmware update didn't behave as advertised because instead of shutting the MacBook Pro completely down, it restarted and then started installing the firmware update.
Ever since the firmware update (which I think installed correctly but don't know how to verify), I cannot boot my MacBook Pro. Using the OS X install DVD I can view my firmware version using System Profiler, and the number it is reporting is MBP53.00A.B03.
I have tried booting in verbose mode to try and get a feel for the problem, and it eventually hangs on an infinite loop saying something about not being able to find something on disk0s2.
I also thought I would fix the problem by doing an Archive and Install, but it quit at the very beginning of installing with the error "unknown error".
Also I thought I would format the disk with Disk Utility and then try installing again, but Disk Utility reports that it in unable to unmount the volume.
Any help you can provide would be greatly appreciated. Thanks!
-- Update --
Remember how I'm unable to unmount the drive? I force unmounted it and then used Disk Utility to repair the volume, but still no luck.
I think the key to the problem is this new HD I put in runs at 3 Gbps. I think I read somewhere that the new MacBook Pro's don't support that.
I think next I should try swapping out the new HD in my MacBook Pro with the one it originally came with. What do you think?

I, too, have a brand new MBP 15" that I put an Intel X25 in. At the 1.5 (Prior to Firmware Update) setting, it worked fine. I rant the Firmware Update, all looked fine, but the drive is no longer able to be seen.
Flash the PRAM, per other suggestions to no avail. Boot off of the DVD and disk utility nor Profiler sees the drive.
Replace the drive with the stock that came with the MBP (which I had never even used) and it works.
Put the Intel X25 into a Windows machine and it works fine. Reformatted it (in windows) and put it back into my MBP. Still not able to see it (from the Disk utility after booting off the DVD).
Intel's firmware for the drive says its up-to-date (new drive) and if I attempt to "re-run" the Mac Firmware Update, it says that the machine is already up-to-date.
Seems odd that it worked before an now it doesn't. Also seems odd that the X25 works in other machines. And that my MBP works just fine with the stock Hitachi 7200 320GB drive.
Ideas? Intel says to call Apple Support. Not sure what I can say to them.

My Mac Pro won't boot after installing the latest update

Im running the latest OSX on my mac and recenty did a small updated that i believe contain a few security thing and bug fixs but when restarting the machine after the update it would not boot again after the apple logo has appeard apple script is displayed on the screen contain what i think is boot script failing to run. I have been able to boot the system in safe mode. does anyone have and solution for this as i realy don't want to reinstall the OS
Thanks

The most common cause for "Won't boot after software Update" is Directory Damage that existed before the Update, but was made worse by adding files during the Update.
The most common cure for that Directory Damage problem is to boot in Safe Mode, which takes five minutes to repair the disk, then comes up demanding your username and password, even if you normally auto-login.
Rarely, third-party add-ons are made obsolete by an update. In this case, booting in Safe Mode (with few Apple extensions and NO third-party extensions loaded) works fine, even if normal mode does not work.
Have you tried normal mode again after your Safe Boot?

Macbook pro won't boot after update to 10.6.8

Hi everyone,
Yesterday I bought an used macbook pro (15 inch early 2008). When looking at it, it was in good shape and the previous owner just did a fresh install of snow leopard. I took it home and whas happy with it. In the first two hours of using it, everything was fine. After installing the update to 10.6.8 my macbook needed to be shut down.. After shutting down it started up again but the screen stayed black. I had no idea why. So I rebooted it by pressing the power button. The same problem remained, it seemed to start up (I could hear the harddrive and fan) but it didn't boot into Mac Os. After a couple of attempts, it now shutsdown immediatly after pressing the powerbutton (3 seconds after). No chime or nothing.
At first I thought this would only be a software problem, because the problem started immediatly after updating. So I put in my snow leopard dvd to boot into that, but I can't even get it to boot into the install dvd. Because it shuts down immediatly after pressing the power button. Then I started suspecting an hardware failure, which would be a very big coincidence to show up immediatly after booting up. These are the things I have tried so far, to no avail:
- Plugging of the power cord and removing the battery, then pressing and holding the powerbutton for at least 5 sec
- Holding the option, command, P and R keys during boot.
- Replacing the memory
- Replacing the hard drive
- Unplugging the super drive
- Starting up holding the d key
At a certain point I was hoping that It would be an harddrive or memory problem. I replaced both with examples I know for sure they are working. But still the same problem; macbook shuts down almostimmedialty after pressing the power button.
There is no warrany anymore, and technical support would cost me 49 euros per incident.. to probably hear that the macbook is beyond repair. I feel i have just thrown away 300 euro's for an nightmare experience. Does anybody now anything to try, i'm really desperate here

After installing the update to 10.6.8
What update was that?
So I put in my snow leopard dvd to boot into that, but I can't even get it to boot into the install dvd.
Did the previous owner also give you the discs that originally came with the computer? Those are what you need to troubleshoot with. You also need disc 1 to run the Apple Hardware Test.
There is no warrany anymore, and technical support would cost me 49 euros per incident..
Apple Store and AASP diagnostic testings are free. Suggest that you take full advantage of it. This way you can find out exactly what is wrong with your computer. Post back here with the diagnosis and someone will post DIY repair sites.

Macbook Pro won't boot after update

I have a macbook pro3,1 (early 2008) that I received from someone else. When I received it, it had os x 10.8.3 installed. Initially I tried to update it to maverick, but after it rebooted it would not boot, just continued to reboot over and over. I then was able to boot into restore mode and do a repair on the disk. After that I was able to boot into 10.8.3.
I decided to update to 10.8.5, and received the same results as before. This time I was unable to restore with a disk repair.
I also created a bootable usb with Mavericks on it. Again, it will not boot to allow an install.
I was able to boot into safe mode, but that did not fix the installation. I tried repartitioning the hard drive and install mavericks on the new partition, but that failed also.
After looking at the logs, I see that there is a kernel panic that happens. Everytime I boot normally, it seems to get just before the login screen before it reboots. Below is the log.
Sat May 31 19:34:08 2014
panic(cpu 0 caller 0xffffff7f881ad8a1): NVRM[0/1:0:0]: Read Error 0x00003250: CFG 0xffffffff 0xffffffff 0x92000000, BAR0 0x92000000 0xffffff804e3b5000 0x084700a2, D0, P2/4
Backtrace (CPU 0), Frame : Return Address
0xffffff804e00b590 : 0xffffff8007a1d636
0xffffff804e00b600 : 0xffffff7f881ad8a1
0xffffff804e00b6c0 : 0xffffff7f88512849
0xffffff804e00b700 : 0xffffff7f884f6480
0xffffff804e00b740 : 0xffffff7f884f9567
0xffffff804e00b8a0 : 0xffffff7f88272911
0xffffff804e00ba20 : 0xffffff7f882ffd5a
0xffffff804e00bc60 : 0xffffff7f882fb64d
0xffffff804e00bd70 : 0xffffff7f882ff530
0xffffff804e00bdc0 : 0xffffff7f8856a0eb
0xffffff804e00bdf0 : 0xffffff7f882ff149
0xffffff804e00be70 : 0xffffff7f88192afa
0xffffff804e00bf30 : 0xffffff7f881526ec
0xffffff804e00bf60 : 0xffffff8007a3e26e
0xffffff804e00bfb0 : 0xffffff8007ab3257
      Kernel Extensions in backtrace:
         com.apple.NVDAResman(8.1.6)[39D35403-42FB-3F08-999C-9866938D6B3A]@0xffffff7f881 4c000->0xffffff7f883effff
            dependency: com.apple.iokit.IOPCIFamily(2.8)[6C1D646D-7E5E-3D7F-A557-2CBA398FF878]@0xffffff 7f880b2000
            dependency: com.apple.iokit.IONDRVSupport(2.3.7)[F16E015E-1ABE-3C40-AC71-BC54F4BE442E]@0xff ffff7f88138000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.7)[9928306E-3508-3DBC-80A4-D8F1D87650D7]@0 xffffff7f880f5000
         com.apple.nvidia.nv50hal(8.1.6)[BF3CC142-4112-3E23-BCE2-CDCFD5811DDA]@0xffffff7 f883fb000->0xffffff7f886cefff
            dependency: com.apple.NVDAResman(8.1.6)[39D35403-42FB-3F08-999C-9866938D6B3A]@0xffffff7f881 4c000
            dependency: com.apple.iokit.IOPCIFamily(2.8)[6C1D646D-7E5E-3D7F-A557-2CBA398FF878]@0xffffff 7f880b2000
BSD process name corresponding to current thread: kernel_task
Mac OS version:
12F45
Kernel version:
Darwin Kernel Version 12.5.0: Sun Sep 29 13:33:47 PDT 2013; root:xnu-2050.48.12~1/RELEASE_X86_64
Kernel UUID: EA38B02E-2B88-309F-BA68-1DE29F605DD8
Kernel slide:     0x0000000007800000
Kernel text base: 0xffffff8007a00000
System model name: MacBookPro3,1 (Mac-F4238BC8)
System uptime in nanoseconds: 79475358847
last loaded kext at 57319258564: com.apple.driver.AudioAUUC          1.60 (addr 0xffffff7f89b42000, size 28672)
loaded kexts:
org.tgwbd.driver.NullCPUPowerManagement          1.0.0d2
com.apple.driver.AudioAUUC          1.60
com.apple.driver.AppleHWSensor          1.9.5d0
com.apple.iokit.IOBluetoothSerialManager          4.1.7f4
com.apple.filesystems.autofs          3.0
com.apple.driver.AppleHDAHardwareConfigDriver          2.4.7fc4
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.driver.AppleHDA          2.4.7fc4
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ApplePolicyControl          3.4.5
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleLPC          1.6.3
com.apple.driver.SMCMotionSensor          3.0.3d1
com.apple.iokit.IOBluetoothUSBDFU          4.1.7f4
com.apple.iokit.BroadcomBluetoothHostControllerUSBTransport          4.1.7f4
com.apple.driver.AppleSMCLMU          2.0.3d0
com.apple.driver.AppleSMBusPCI          1.0.11d1
com.apple.GeForce          8.1.6
com.apple.driver.AppleUpstreamUserClient          3.5.12
com.apple.nvidia.NVDAStartup          8.1.6
com.apple.driver.AppleMuxControl          3.4.5
com.apple.driver.AppleBacklight          170.3.5
com.apple.driver.AppleMCCSControl          1.1.11
com.apple.driver.AppleUSBTCButtons          237.1
com.apple.driver.AppleUSBTCKeyEventDriver          237.1
com.apple.driver.AppleUSBTCKeyboard          237.1
com.apple.driver.AppleIRController          320.15
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.iokit.SCSITaskUserClient          3.5.6
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.3.5
com.apple.driver.AppleUSBHub          635.4.0
com.apple.driver.AirPortBrcm43224          600.36.17
com.apple.iokit.AppleYukon2          3.2.3b1
com.apple.driver.AppleFWOHCI          4.9.9
com.apple.driver.AppleAHCIPort          2.6.6
com.apple.driver.AppleIntelPIIXATA          2.5.1
com.apple.driver.AppleUSBEHCI          621.4.6
com.apple.driver.AppleUSBUHCI          621.4.0
com.apple.driver.AppleSmartBatteryManager          161.0.0
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.8
com.apple.driver.AppleACPIButtons          1.8
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.8
com.apple.driver.AppleAPIC          1.7
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2.1
com.apple.driver.AppleIntelCPUPowerManagement          214.0.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.kext.triggers          1.0
com.apple.driver.DspFuncLib          2.4.7fc4
com.apple.iokit.IOAudioFamily          1.9.2fc7
com.apple.kext.OSvKernDSPLib          1.12
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.4.7fc4
com.apple.iokit.IOHDAFamily          2.4.7fc4
com.apple.iokit.IOSurface          86.0.4
com.apple.iokit.IOBluetoothFamily          4.1.7f4
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.4.1d13
com.apple.iokit.IOBluetoothHostControllerUSBTransport          4.1.7f4
com.apple.driver.AppleSMC          3.1.5d4
com.apple.nvidia.nv50hal          8.1.6
com.apple.NVDAResman          8.1.6
com.apple.driver.AppleGraphicsControl          3.4.5
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.iokit.IONDRVSupport          2.3.7
com.apple.driver.AppleSMBusController          1.0.11d1
com.apple.iokit.IOGraphicsFamily          2.3.7
com.apple.driver.AppleUSBMultitouch          237.3
com.apple.iokit.IOUSBHIDDriver          623.4.0
com.apple.driver.AppleUSBMergeNub          621.4.6
com.apple.iokit.IOSCSIBlockCommandsDevice          3.5.6
com.apple.iokit.IOUSBMassStorageClass          3.5.2
com.apple.driver.AppleUSBComposite          621.4.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.6
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOATAPIProtocolTransport          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.6
com.apple.iokit.IOUSBUserClient          630.4.4
com.apple.iokit.IO80211Family          530.5
com.apple.driver.AppleEFINVRAM          2.0
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOAHCIFamily          2.5.1
com.apple.iokit.IOATAFamily          2.5.1
com.apple.driver.AppleEFIRuntime          2.0
com.apple.iokit.IOUSBFamily          635.4.0
com.apple.iokit.IOHIDFamily          1.8.1
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220.3
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          345
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.21
com.apple.driver.AppleACPIPlatform          1.8
com.apple.iokit.IOPCIFamily          2.8
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
I received the macbook from someone else without installation disks. Also, when try to do a re-install of 10.8.3 from the internet in restore mode, it tells me that the account does not match the one the purchase was made from. I would rather not run 10.8.3 anyway if I could install mavericks.
Below is the system information for the macbook
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro3,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.4 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache:          4 MB
Memory:          2 GB
Bus Speed:          800 MHz
Boot ROM Version:          MBP31.0070.B07
SMC Version (system):          1.16f11
Serial Number (system):          W87422HUYAM
Hardware UUID:          00000000-0000-1000-8000-001B63A5B553
I have tried to reset nvram as well as smc with no result.
I have also done a extended apple hardware test which found no errors.
The macbook does have a bad battery, so I have tried booting without the battery. The results did not change.
I have searched the internet for the kernel panic error and can not find a consistent issue for macbook pros. Some say it is a hardware problem. Others say it is an install problem. What does not make sense to me is if it is hardware problem, why was I able to restore it back once and get it to boot consistently. It seems to be directly the result of updating the software.
I also read that 10.8.5 consistently had boot problems upon install, so I tried re-installing the combo update for 10.8.5
I feel like I have exhausted almost all the resources except taking it to the genius bar.
Please let me know if you can help.
Thanks,

bereanmh,
since your MacBook Pro didn’t originally have Mountain Lion installed at the factory, the former owner erred in leaving it on its internal disk when transferring it to you; Mountain Lion is non-transferable when sourced from the Mac App Store. The former owner should rather have provided you with its original pair of grey installation discs, which hold its original version of Mac OS X, its iLife apps, and its model-specific Apple Hardware Test. If you didn’t receive these discs, you can contact Apple directly to purchase a replacement pair. (They’re not available in Apple stores.)
That being stated, regarding the panic report above, the prime suspect is that NullCPUPowerManagement kernel extension — try uninstalling it to see if that makes a difference.

Macbook Pro Won't Boot After Starting Lion Install

2008 Macbook Pro 17" with Core 2 Dou processor.
Internal Disk has two Partitions
Downloaded Lion from App store and ran installer. Selected 2nd partition which is Mac OS Extended Journaled. (I was intending to do a clean install on this empty partition.)
Installs appears normal, goes to boot and hangs at the gray screen after the chime.
Verbose logging does not show anything obvious, no more info after identifying the network adaptors.
Booting with option key does not give option to boot to Snow Leopard partition.
I

Welcome to Apple Support Communities
Press Command and R keys when your Mac starts and reinstall OS X. Mountain Lion is damaged in the computer

Macbook Pro won't boot after Mountain lion upgrade

I bought the Mountian Lion upgrade and it installed fine on my MacBook Pro, and the machine worked fine yesterday. I performed a normal shutdown, and today it won't boot up. The Apple logo and the spinning pinwheel is all I get. Is there a known issue?

Welcome to Apple Support Communities
Press Command and R keys when your Mac starts and reinstall OS X. Mountain Lion is damaged in the computer

Early 2008 MacBook Pro won't boot after Lion 10.7.1 update

My 2.4 GHz 4GB RAM Early 2008 MacBook Pro wont boot after downloaded the Lion 10.7.1 upate. Upon restarting the screen went dead and now the system does not boot, as if the bootloader has been wiped out. Screen appears dead but was known to be working before hand. The hard drive spins up but doesn't sound like it is searching for data.
Can anyone help me?

Okay, I tried everything I can think of last night. I removed every startup process and every tool or programm that goes deeper into the system (GlimmerBlocker, LittleSnitch, Parallels). Cleaned Up every Cache I could find and refreshed every necessary Cache or Database possible. Took me a couple of hours. But still no luck - the machine doesn't boot, just in safe mode. Right now I copy all my personal stuff to a new external harddrive because TimeMachine doesn't work, after this I will do a clean install of Lion.
It's not hardware related, it's the 10.7.1 update that doesn't work properly. By the way, the only errors remaining are:
WindowServer - kCGErrorFailure
ManagedClient - kCGErrorFailure: CGSPackageGetWorkspaceType: couldn't get workspace type
SecurityAgent - kCGErrorFailure: CGSPackageGetWorkspaceType: couldn't get workspace type
and a lot of:
com.Apple.SecurityAgent.00000000-0000-0000-0000-0000000186A7: CoreAnimation: rendering error 506
that's also the last one I get before the system hangs…

MacBook Pro won't boot after ram upgrade...

Hey everybody! Hope everyone is having a great Christmas! I got a 16gb ram upgrade for my 2012 MacBook Pro 15 today and I am having some trouble with the upgrade. Its an odd problem. I installed the two 8gb sticks no problem, but when I try and boot into OS X the machine shows the apple logo with the spinning wheel underneath, and then it just shuts itself off. I don't know what the problem is. The machine boots fine into my Windows 7 partition, and registers both sticks of ram. OS X restore also boots no problem and lets me reinstall OS X, which is what I am doing currently. IDK if this is just because of a hardare change or what. The ram I installed is Adata pc3 12800 1600mhz ram, so it should be supported.

Replace the Ram, buy from OWC or Crucial, buy the Ram Apple recommend, don't rely on "it should work"

Macbook Pro won't boot after TM restore

Hi.
My MacBook Pro was running snow leopard with all the latest updates, when the hard drive crashed. I booted from the dvd that came with the macbook, osx 10.5.4, restored the latest Time Machine backup. Everything seemed fine until I try to reboot. I get the grey screen and the message:"You need to press the powerbutton for several seconds". I've reset the pram, powermanager and ran a hardware check that turned out ok. Does anyone have any clues as to what's wrong?
Any help would be greatly appreciated,
Regards, Espen Noreger

enoreger wrote:
Hi.
Hi, and welcome to the forums.
My MacBook Pro was running snow leopard with all the latest updates, when the hard drive crashed. I booted from the dvd that came with the macbook, osx 10.5.4, restored the latest Time Machine backup. Everything seemed fine until I try to reboot. I get the grey screen and the message:"You need to press the powerbutton for several seconds". I've reset the pram, powermanager and ran a hardware check that turned out ok. Does anyone have any clues as to what's wrong?
Yes. You need to use your +Snow Leopard+ Install disc, not the Leopard one.

MacBook Pro won't boot after update to 10.10.1

I have just updated to 10.10.1 and my MacBook Pro refuses to come back to life.
All I get is a white screen and no sign of activity.
Any clue?
Pierre

Hey Pierre6405,
I see that you are having issues getting your computer started up into OS X. I have an article for you with some troubleshooting suggestions that should help you get started on addressing the issue:
Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
http://support.apple.com/en-us/HT201177
Thanks for being a part of the Apple Support Communities!
Cheers,
Braden

Macbook Pro won't startup after 10.9.1 update

Early 2013 Macbook Pro 13" retina running Mavericks.
Installed the 10.9.1 update and left it to do that and when I returned it had restarted in Bootcamp in Windows 8.1
Requested in Windows that it startup in OSX. On starting up OSX a message came up saying there was a problem starting.
It tries to startup a couple of times then a circle with a line though it comes up and it goes no further.
Tried booting into recovery mode to check permissions etc. in disc utility but that's not coming up either.
Any suggestions on what else to try?

Chose startup disk manually:
Hold the Command button during startup, then select your macintosh partition.
Reset the nvram:
Turn on your mac while holding Command-Option-P-R until the chime sounds for the second time.
Safe boot:
Boot while holding down the RIGHT shift button.
If you have a Time Machine, you can use that to restore.
Reinstall via recovery:
Hold down Command-R during boot, then hit reinstall in the menu.
Other than that, you'll have to go to a Genius Bar.
Hope this helps!

Macbook pro won't boot after updating to 10.9.3

I ran the update to 10.9.3 yesterday. After reboot the Mail program gave me an error that it might not be compatible with the OS. I restarted, now I get the a progress bar. It goes for about 30 seconds then powers the macbook down.
Here's what I've tried.
1. Booting into recovery mode (both Internet recovery and regular recovery)
2. I cant repair permissions or repair the disk. It says that it needs to be reloaded, etc
3. I tried a reinstall. I'm getting a disk locked error on the Macintosh HD and recovery HD.
4. Can't boot into safe boot. I get a driver error and Mac OS Version: not set yet.
5. I tried Turning off Encryption. It won't turn off.
6. When I choose the startup disk to boot to, it still shows 10.9.2, even though the app store showed that 10.9.3 was installed.
Pretty much combed the forums, but I'm not really sure what to do at this point. The machine is out of warranty and I don't have another Mac to do any cloning, usb startup disks, etc. I made an appointment with the genius bar tomorrow but I wanted to see if there's something else I can try! Any help would be greatly appreciated!
Thanks.
Dan

Do you have a Time Machine backup? If so, erase the disk and reinstall OS X. HOWEVER, DO NOT CONTINUE UNLESS YOU HAVE A TIME MACHINE BACKUP!!! IF YOU DO NOT HAVE A BACKUP AND STILL DECIDE TO CONTINUE, BE AWARE THAT ALL YOUR DATA WILL BE LOST FOREVER!!!
Erase and Reinstall OS X
Note: This will delete all data on the disk. Back up important files before continuing.
Erasing and then reinstalling OS X can give you a fresh start, making your computer exactly as it was whenever you received it from Apple. This can solve various problems such as corrupt system files.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
Press the Power Button to turn on the computer.
Press and hold both the R and Command (⌘) keys on the keyboard until the Recovery partition loads. If this does not work, shut down the computer, press the Power Button to turn on the computer, and then hold in the Alt (⌥) button immediately after you press the power button. Then, select the Recovery HD partition to boot up in the Recovery HD partition.
Select Disk Utility and then choose Continue.
Select your startup disk (Macintosh HD by default) from the left.
Select the Erase tab.
Choose the Format pop-up menu and choose Mac OS Extended (Journaled), enter a name for your disk, and then click Erase.
After the disk is erased, choose Disk Utility > Quit Disk Utility.
Select Reinstall OS X and then choose Continue.
Follow the instructions.
I hope I helped.
Austin

MacBook Pro won't boot after 10.6.8 update.

Similar Messages

Maybe you are looking for