MacBook Pro won't get past the flashing grey file screen?

Ok, so tonight I try turning my MacBook on as normal, it then froze and I saw the rotating umbrella appear. So I restarted it. When trying to turn back on, the system did not load, instead a flashing grey file shape came up with a question mark inside. I have tried restarting with a number of key combinations, Option; option, ALT, P, R. Everything, yet it's not getting past this screen. Whenever I try to do an Internet recovery, it just stays on the wifi selection screen and I select mine, enter the password and then it just goes back onto the selection screen. Nothing is work yet! Incredibly annoyed as it has so much stuff, photos, music everything. I don't even know how I reinstall software as it's stuck... Can someone please help? My software is 10.7 I believe.

Hi PHXSuns,
If you are seeing a flashing question mark on startup, you may find the following article helpful:
Apple Support: A flashing question mark appears when you start your Mac
https://support.apple.com/kb/TS1440
Regards,
- Brenden

Similar Messages

New MacBook Pro, unable to get past the select your country screen during initial setup.

I purchased a new MacBook Pro last night and am unable to get past the initial setup screen where you select your country. The mouse will move around, but won't actually allow me to click on 'continue'. I've also tried the keyboard commands to move to the next screen. Nothing...

I just experienced this, and I am recording the solution here for posterity. I got through the setup using the keyboard (tab to move between controls and space to select), thinking that the mouse click would work when I got through it. But I was dismayed to find that it did not ...
... at least so I thought! But actually, you have to push down the mouse pad, NOT just tap it. You can turn on tap-to-click later, but at the start you must push it until it audibly clicks. It is not obvious if you are used to Windows laptop mouse pads like me, where tap-to-click is the ubiquitous norm.

MacBook Pro won't get past the apple screen on startup

The laptop won't startup. I get to the Apple logo and a spinning gear. I've tried starting it 3 times with the same result.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

My macbook pro will not get past the gray screen with the apple logo and a loading bar.

My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.

You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213

I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?

I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?

sideeque wrote:
I have the same problem. What did you do last time?
What should I do now? Its around 40 miles away the apple store? Would they pay my taxi fare to go and return?
How can we trust this apple product?
You are still under warranty. Call Apple Care.

My Macbook pro won't get passed the grey startup screen

My apple macbook pro is not getting passed the gray screen with the apple and spinning circle. I have tried pressing comand-R or shift-command-v, and nothing happens what so ever. I listened to my hard drive, and it sounds fine. It sounds like it is running, and there is no clicking sounds from it or anything, and haven't been any at all. Nothing seems to make it respond

Direct you to the proper forum for MacBook :
MacBook Series Forums
https://discussions.apple.com/community/notebooks?view=discussions
https://discussions.apple.com/community/mac_os?view=discussions
http://www.apple.com/support/macbookpro

How to get past the Flash Player Download screen when a newer version is already installed?

Does anyone know how I can get past the Flash Player Download? I already have a newer version then what is trying to load. Therefore, I get a screen telling me the same, but I still can't access the files I need. It is a vicious loop I'm stuck in. Can anyone help me?

Hi..
Are you running Lion v10.7 by chance even though your profile indicates v10.6.8 ??
I ask because you can only reinstall apps using Lion Recovery
Much better to ask for help with Safari here before trying to delete the app and reinstall.
Is the Safari app still in the Trash by chance?

Turning on and the apple chime is heard but won't get past the first grey screen

Turning on the Mac and hearing the chime but not able to get past the initial grey screen.

Hello Daryl,
Also let us know what Operating System you have on your Mac.

MacBook Pro won't get past grey startup screen

I have a late 2011 15 inch MacBook Pro running Mavericks. Around a month ago, maybe more, it began to sometimes completely freeze or just turn off while Inwas using it. Sometimes it would start up again, sometimes it wouldn't and would beep three times. Eventually it wouldn't start up at all and would just beep. I started it up in recovery (holding command +R) and ran a disk repair, it said the disk couldn't be repaired. I had it backed up on Time Machine so I replaced the HD and restored from Time Machine. It was fine for a couple days after that, then the old symptoms returned. I took the RAM out and replaced them with some RAM of the same size (2 chips, 2GB each) taken out of a Windows laptop that I had. Again, it was fine for a few days then started turning off and beeping. Then it would turn on but not boot up, i.e. get stuck on the grey screen with the spinning circle. I tried booting in recovery, booting into safe mode, holding option and choosing a disk; in all cases it would just stay stuck on grey screen with the spinning thing. I tried PRAM and SMC reset, no result. At one point, it got through boot up in safe mode but took like an hour to do so. I restarted from safe mode and it took another hour and booted up normally. Then it turned off again and wouldn't turn back on. I opened it up, reseated the RAM and cleaned he fans, which were filled with dust and build up. It turned on and ran normally for a couple days in which I wasn't doing much on it, just watching stuff on VLC or reading, so not really using it and clicking and stuff. Next day, I open it (from sleep, it hasn't been shut down at all since I got it to run again), and try to open Firefox and actually work; it keeps freezing and being incredibly slow, to the point where it was totally frozen and I couldn't force quit or anything. So I held the power key to shut it down; since then it's back to not getting past the grey screen, even when I leave it for over an hour. No idea what to do, anyone have an idea? Thanks in advance.

You have to use Mac specific RAM chips.
You have to buy new RAM modules, I guess.
If you have extended AppleCare, contact Apple.
Best.

MacBook Pro won't get past gray start screen - RunTime corruption error

Hi, I am a novice when it comes to fixing things, so I will make a Genius Bar appointment, but I thought I would consult this community first in case anyone has experienced this same issue:
I was using my 13 in. MacBook Pro this morning after not using it for a couple weeks. (It was running fine last time.) It started up fine, and the few applications I was using worked OK. Then I got an error saying I needed to update my Java in order to access my work VPN. I didn't think twice about downloading the Java upgrade. Once the Java download was complete, I thought I might need to restart to get the VPN to recognize the update. And that was the last time I was able to see my desktop. I restarted, and the could not get past the gray screen. I did this twice. Then I did a safe boot (showing the status of the progression), and that when I saw this message over and over and over:
hfs: RunTime corruption detected on MacIntosh HD, fsck will be forced on next mount.
hfs: BlockMarkFreeInternal () trying to free unallocated blocks (10865570,8) on volume MacIntosh HD
(I snapped a pic with my phone - that's how I transcribed it.)
This ran for about 20 minutes before I suspected it wasn't actually doing anything, and I forced it to shut down by pressing the power button.
I just tried to start it again (fingers crossed, hoping for a miracle), but no such luck. Does anyone have any ideas? Is all lost? Thank you in advance for any recommendations!
Jennifer

I should add that I don't know if the Java download is responsible - could just be a coincidence that it was the last thing I did/downloaded before restarting.

MacBook Pro won't get past Apple logo during boot

Hey, recently while I was using on my MacBook Pro (note: just simply browsing the internet), the battery ran dry and the computer shut down almost immediately. When I plugged it in and turned on the computer again, the familiar Apple logo appeared and looked as though it would start up normally. However, an unfamiliar grey progress bar appeared and the usual grey gear started spinning. The progress bar looks as though it reaches up 10-15% completed but the computer just shuts down after that every time. I know it has nothing to do with the charge in the battery as I tried doing it plugged in and even waiting overnight for the battery to charge fully with the plug plugged in.
So, I tried using Disk Utility on the Snow Leopard Install disc (my original MacBook Pro install discs had Leopard on it so I just used the Snow Leopard discs instead). After using the "Verify Disk" command on the Macintosh HD volume, it stated that 'Invalid node structure' and then stated that the disk could not be verified and needed repair. I then proceeded with using 'Repair Disk' and it did say 'Volume repair complete' but then stated 'Updating boot support partitions for the volume as required.' This was when an error popped up and said "Error: Disk Utility can't repair this disk" and then told me to back up my files and reformat the disk.
I'm hoping that I don't have to reformat the disk as I haven't backed up in a while. I do have a separate partition on the hard drive that has Windows 7 on it that I can boot to. At least that means my hard drive hasn't completely died on me. However, I'm unsure what to do at this point to fix the computer. I tried to Safe Boot but it didn't change the outcome of start up.
Any ideas as to what I can do? I appreciate any help.

Thanks for the replies! Anyway, I gave DiskWarrior a try and it failed to work. The first time I tried it, I put the disc into the drive of my MacBook Pro and booted it from the disc. After going through the rebuild process it told me that due to a hard drive malfunction it couldn't append any changes to the drive. I then tried putting the disk into my iMac and used my MacBook Pro in Target Disk mode. This wouldn't even attempt to rebuild my drive saying that there was a hardware failure.
So, I booted into Windows 7 and saw that Windows was able to access the drive and read the files perfectly. All the files were in tact. I don't understand why disk warrior had a problem with it. Anyway, what I can do is reinstall Mac OS X Snow Leopard onto the hard drive again after moving the data onto an external hard drive using Windows. The only problem is that I would have to reinstall all of my programs while reimporting all of the settings and data that I can from the external hard drive. What I want to know is can I make an image of my hard drive (with SuperDuper?), and append that back onto my Mac's hard drive? Would that work again after reformatting the disk or would it just give me the same problems as before? Would it be better or easier to just start new and reinstall everything? Thanks!

Macbook pro won't go past the apple logo (Lion)

I've installed Java Runtime, and after that tried to use "software update" but the application quit.
Tried to restart, but it stays stuck on the apple logo (with the wheel turning) for ages. Restarted in recovery mode, ran disk utility, repaired permissions and verified disk. no problems found. Restarted again, still the same thing - won't go past the apple logo.
If reinstall is the only way to go, is there a way to access this hard drive to back up files (it is a recent computer, still hadn't made any backups...)
Thank you all, help would be much appreciated!

Shut down and startup holding command-r keys into Recovery Disk from there choose Disk Utility and Repair Disk.
polymolly wrote:
I've installed Java Runtime, and after that tried to use "software update" but the application quit.
Tried to restart, but it stays stuck on the apple logo (with the wheel turning) for ages. Restarted in recovery mode, ran disk utility, repaired permissions and verified disk. no problems found. Restarted again, still the same thing - won't go past the apple logo.
If reinstall is the only way to go, is there a way to access this hard drive to back up files (it is a recent computer, still hadn't made any backups...)
Thank you all, help would be much appreciated!
Ooops you've been there, done that. You can use Target Disk Mode if you have another Mac.
EDIT: Was the Java Runtime from Software Update?

My MacBook Pro won't go past the white apple page

My computer won't go past the white apple page with the spinning wheel when you turn it on.

This should fix the problem:
Reinstalling Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Macbook Pro won't get past admin login screen

2.53 ghz 13" MBP osx 10.6.4
It starts up and gets to the login screen where it usually has the box to put in the password. But now it just shows the account name and little icons below in that window for sleep, restart, shut down. But it's not responsive to any clicks. I can move the cursor, but nothing else. All I can do is hard shut down but then it does the same thing whenever I restart.
Any ideas? Thank you.

I figured it out. A track pad option was deselected in System Preferences that messed it all up. I got past the login screen with key commands then used my 17 MBP to share screen and changed the track pad settings on the 13 MBP. Phew, that was weird.
It was nice having this exchange with myself in a public forum though...

MacBook Pro won't get past the flashing grey file screen?

Similar Messages

Maybe you are looking for