MacBook Pro won't turn on or charge or show battery indicator

Yesterday I plugged my phone into my MacBook Pro 13" using a knockoff USB cord (my charger), my phone wouldn't connect and then the screen on my MacBook just went black and it completely shut off. I tried pressing the power button to turn it on and nothing happened. I checked the battery indicator on the side and no lights came on (not even the blinking red one that tells you your macbook's dead or low battery). I plugged in my MacBook charger and it was green for a few seconds and then the light shut off. I unplugged the charger from the socket and then plugged it back into my MacBook and the light starting blinking a faint green and orange and it still would not turn on. I let it sit overnight without being plugged into the charger and today it won't connect to the charger at all and still won't turn on. Any ideas?

If your Mac won't turn on - Apple Support
also free check-up http://www.apple.com/retail/storelist/

Similar Messages

My macbook Pro won't turn on, is it because the battery pack is dead?

My Macbook Pro won't power on. Is it because the battery pack has died?

Well yes if it isn't connected to the AC.

Macbook pro won't turn on or charge. Help?

I used my Macbook Pro last night and it was perfectly fine. I turned it off, still with battery life. This morning I tried turning it on, nothing happened. So I tried plugging it in to charge to see what would happen. Nothing. The light of the charger usually turns bright green. But it didn't light up at all. You could see that it turned a little bit green but you can't notice. Also, my charger was doing fine last night. I haven't been using my mac for even a year yet. I started using it around November to December. I'm a bit disappointed. I take good care of my mac. My Dell laptop is still working and I have had it before I got my mac. I changed it battery once, but it was almost 2 years after I got the Dell. I would really appreciate help. All my school work are in my mac and I have no way of getting to them. I also need it fixed asap. I chatted with Apple Support, but it's still the same. I had to go to school so I couldn't do much either. Thank you very much!!

Hi FilipinoAndProud,
I recently had the exact same issue as you. My laptop wouldn't power on and the charger when plugged in would have a dim green light. I was so frustrated because my Macbook is one month out of the warranty.Anyway I managed to fix the problem by using this post
https://discussions.apple.com/message/22799811#22799811
Budoghost
HT3964 Re: My macbook pro charger won't charger but it has a dim green light on
Aug 23, 2013 10:24 AM (in response to dominic23)
I had this Problem but now solved. I had to disconnect the battery inside your MacBook Plug your MagSafe charger in (with battery still disconnected inside) and the dim green light will go back to bright green again. Insure your MacBook is turned off Reconnect your battery screw case back on and Enjoy your Fix Macbook.
I hope this helps you.

13" Macbook Pro won't turn on or charge

I have a 2011 macbook pro (13") which shut down while I was watching a movie last night. I connected it to the charger this morning and it restarted but the LED on the magsafe charger is green and it said "Not charging" next to the battery icon on the screen. It died after 2-3 minutes of use and won't turn on since then. I am really not sure why this is happening. I have checked that the charger works with another MBP so its not a problem with the charger. When I press the button to check the battery charge the first light flashes for 4-5 seconds. I tried resetting the SMC by following the steps mentioned on here but it still won't restart. Does anyone know what I can do about this problem? I would bring it in to the Apple store but I am travelling and need the computer for work. Any help would be greatly appreciated. Thanks.

Might be something you haven't tried here > Troubleshooting: My computer won't turn on
And here > Apple Portables: Troubleshooting MagSafe adapters

My macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?

my macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?

Might be a problem with the adapter.
Help here > Apple Portables: Troubleshooting MagSafe adapters

My macbook pro won't turn on without any reason?

my macbook pro won't turn on without any reason, is there any solution in this case?

You need to hit the "reply" button on post to whom your responding too, it's hard to tell if your responding to me or someone else.
small button on the side of the computer and didn't lightting up( no reponse at all). is their any problems do think with the battery?
Usually if your battery is dead because it wasn't charged you can do the SMC Reset and then check the Magsafe if it's connected and showing the orange light, then let the battery charge up.
Once the battery charges up, the computer will boot normally and then you have to reset the PRAM, time, date etc.
https://support.apple.com/kb/TS1365
Magsafe issues: https://support.apple.com/kb/TS1713 https://support.apple.com/kb/TS4127
*PRAM Reset http://docs.info.apple.com/article.html?path=Mac/10.6/en/26871.html
What's store in PRAM https://support.apple.com/kb/HT1242
Hardware Test
https://support.apple.com/kb/ht1509

My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?

My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?

Mac OS X: Gray screen appears during startup

My MacBook pro won't turn on all the way gets to the apple with the spinning wheel underneath and that's all I need help asap

My MacBook pro won't turn on it just gets 2 the spinning wheel and keeps spinning

Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
If this doesn't work then you will need to erase the drive and install Snow Leopard from scratch:
Erase and Install Snow Leopard
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. When completed quit DU and complete the Snow Leopard installation.

My MacBook Pro won't turn on although the battery life is showing full

My MacBook Pro won't turn on although my battery life is showing full ,

Go step by step and test.
http://support.apple.com/kb/TS1365
Note: Steps 5 and 6
Step 5
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".

My MacBook Pro won't turn on. What keys do I use toed last week.

My MacBook Pro won't turn on. What are the keys to reboot? This happened last week.

http://support.apple.com/kb/HT3964 if you haven't replaced the PRAM battery in the last 4 years.
If you have:
http://support.apple.com/kb/HT1379
Note, the PRAM battery is not the normal replaceable battery for power. It is the equivalent of the PC CMOS battery.

My MacBook Pro won't turn on, what's wrong?

My MacBook Pro won't turn on. What's wrong?

gobetty wrote:
My MacBook Pro won't turn on. What's wrong?
Depends upon what you mean by it not turning on, there are various causes.
Is the power button pressed and nothing happens? Disconnect all other devices, then a SMC and NVRAM reset.
Is there a white screen and nearly nothing? A hosed EFI firmware.
Is there a grey screen and a loading bar that gets stuck? Either a failed firmware update or corrupted drive/OS X.
Is there a grey screen with a spinning wheel? Bad third party or Apple at boot kext file.
Are you loading but not able to log in? Possible corrupt third party software designed to startup upon login.
..Step by Step to fix your Mac

Macbook Pro won't login after sleep (sleep with low battery -- mac turned off maybe it's called save sleep)

Macbook Pro won't login after sleep (sleep with low battery --> mac turned off maybe it's called save sleep)
So if I hit the powerbutton my mbp booted like it is booting from the save sleep (so very fast and the login screen is there in about 10 sec.and there is no apple logo while booting just the desktop screen in "unsharp" ore foggy however...)
Then when i see the login (if the keyboard backlight turned on) i wand do tipe in my code but it won't work... the trackpad is not working; and when i plug-in a usb mouse the mbp is not powering on the usb-mouse (laser is off)
Why is that this way?
Is there n option to wake up the mbp fromm deep/save sleep without haveing issiues after that?
THX

Sorry for such a long delayed response...
I was able to get to an apple store this past weekend, and let me tell you... I'm about finished with there great "support".
Right before I went to the store, I tried to eject a disk. Well the cloth in the SuperDrive (I assume to protect the drive from dust and such) Pulled up with my disk. So I get the Apple store, describe my problem and what happened with the cloth piece. The "Genius" writes up a form and tells me they have to run diagnostic and it will take a couple days... and I will get a call when its done (1-3 days).
Well on day number 3 I called up the store and they told me it was ready to be picked up? I asked if anything had been fixed and they told me they could not reproduce my "sleep issue", so they couldn't fix that.. but told me the cloth piece in the SuperDrive had been fixed.
I drive an hour (one way) to the Apple store to find that all they did was PULLED OUT the cloth... they did not replace it! So basically I have a hole for a Super Drive.
I asked why I was not called to say that my computer was ready to be picked up... didn't get an answer on that one.
I asked why my SuperDrive was said to be fixed, when nothing was done... they told me that it would have to be sent out to the factory store for that to be fixed (FIRST TIME THEY MENTIONED THAT!) Oh, and that would take 5-7 business days. Well that's not going to happen right now considering I'm a college student that NEEDS a working computer!
So I go home, angry... start just putting all my important documents back on the computer. And the screen starts blinking!!!! I guess now I have the same thing described in another post on these forms...
Lets just say that I'm not very happy with Apple right now! If anybody else has success on either the sleep issue or the screen blinking issue, please let me know!
Thank you!

I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen goes to blue screen and that is it...HELP

I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen turns blue and that is it. HELP!!

Run through this list of fixes
Step by Step to fix your Mac
You can do this to copy and remove files from the non booting internal
Create a data recovery/undelete external boot drive

My macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on.

my macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on. i don't know how to get it to progress past this loading page.

Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstalling Mavericks, Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion, Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
If you are not using Lion, Mountain Lion, or Mavericks then use the following procedure:
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.

Macbook pro won't power up or charge after i cleaned the screen and keyboard with a damp cloth.

My macbook pro won't power up or charge after i cleaned the screen and keyboard with a damp cloth

Do not try to use it. Make an appointment at an Apple store genius bar and have the technicians evaluate it for FREE.
Ciao.

MacBook Pro won't turn on or charge or show battery indicator

Similar Messages

Maybe you are looking for