MacBook Pro won't turn on or "wake up" when opened
Hey guys,
I've been having the following issue quite often over the past few days. I always use my MacBook Pro connected to a power source, however, when I go to study at the library or something like that, I don't usually bring my power adapter with me, I just run it on battery power. But once I open it when I get there, I hear the hard drive make the "waking up" noise, but the screen stays blank and doesn't respond to any mouse movements or key presses. I am forced to hold the power button and restart it every time, and it's quite frustrating.
To put it simply, when I use my computer plugged in, close it, unplug the power cord, then open it up (unplugged), it does not "wake up" or turn on.
I was hoping some of you might be able to help me with this!
Note: This happened once today when my I opened my computer again, still plugged in to a power source.
Thanks,
Spencer
Same problem for a couple of weeks.
I've read many posts on this type of problem, and I recently updated my software so I have:
* Leopard 5.2, with...
* Latest Graphics Update
* EFI Update with Boot ROM Version: MBP31.0070.B07
I most often have the problem after suspending my machine which was connected to an external Viewsonic 22" monitor (VX2235wm).
I find that if I let the system hibernate, pull out the battery, put it back in, and then reboot the system that it returns from hibernation with the screen intact but with no responsiveness whatsoever.
If I wake the system up very soon after suspending, less problems. However, if I wait an hour or two to wake-up, I run into the problem.
This may all be anecdotal, I'm just hoping Apple is listening....
Similar Messages
-
My MacBook Pro won't turn on, only a white screen with spinning circle, I've only had it a few weeks! Any ideas what is going on?
Mac OS X: Gray screen appears during startup
-
My MacBook pro won't turn on it just gets 2 the spinning wheel and keeps spinning
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
If this doesn't work then you will need to erase the drive and install Snow Leopard from scratch:
Erase and Install Snow Leopard
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
4. When completed quit DU and complete the Snow Leopard installation. -
My MacBook Pro won't turn on although the battery life is showing full
My MacBook Pro won't turn on although my battery life is showing full ,
Go step by step and test.
http://support.apple.com/kb/TS1365
Note: Steps 5 and 6
Step 5
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own". -
My MacBook Pro won't turn on. What keys do I use toed last week.
My MacBook Pro won't turn on. What are the keys to reboot? This happened last week.
http://support.apple.com/kb/HT3964 if you haven't replaced the PRAM battery in the last 4 years.
If you have:
http://support.apple.com/kb/HT1379
Note, the PRAM battery is not the normal replaceable battery for power. It is the equivalent of the PC CMOS battery. -
My MacBook Pro won't turn on, what's wrong?
My MacBook Pro won't turn on. What's wrong?
gobetty wrote:
My MacBook Pro won't turn on. What's wrong?
Depends upon what you mean by it not turning on, there are various causes.
Is the power button pressed and nothing happens? Disconnect all other devices, then a SMC and NVRAM reset.
Is there a white screen and nearly nothing? A hosed EFI firmware.
Is there a grey screen and a loading bar that gets stuck? Either a failed firmware update or corrupted drive/OS X.
Is there a grey screen with a spinning wheel? Bad third party or Apple at boot kext file.
Are you loading but not able to log in? Possible corrupt third party software designed to startup upon login.
..Step by Step to fix your Mac -
my macbook pro won't turn on and it is plugged into the charger, the light doesn't even turn a color?
Might be a problem with the adapter.
Help here > Apple Portables: Troubleshooting MagSafe adapters -
My macbook pro won't turn on without any reason?
my macbook pro won't turn on without any reason, is there any solution in this case?
You need to hit the "reply" button on post to whom your responding too, it's hard to tell if your responding to me or someone else.
small button on the side of the computer and didn't lightting up( no reponse at all). is their any problems do think with the battery?
Usually if your battery is dead because it wasn't charged you can do the SMC Reset and then check the Magsafe if it's connected and showing the orange light, then let the battery charge up.
Once the battery charges up, the computer will boot normally and then you have to reset the PRAM, time, date etc.
https://support.apple.com/kb/TS1365
Magsafe issues: https://support.apple.com/kb/TS1713 https://support.apple.com/kb/TS4127
*PRAM Reset http://docs.info.apple.com/article.html?path=Mac/10.6/en/26871.html
What's store in PRAM https://support.apple.com/kb/HT1242
Hardware Test
https://support.apple.com/kb/ht1509 -
I have 12,000 photos on iphoto and my macbook pro won't turn on...gray screen turns blue and that is it. HELP!!
Run through this list of fixes
Step by Step to fix your Mac
You can do this to copy and remove files from the non booting internal
Create a data recovery/undelete external boot drive -
my macbook pro won't turn on. it just stays stuck on a white screen with a little circle spinning around and around when you power it on. i don't know how to get it to progress past this loading page.
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstalling Mavericks, Lion/Mountain Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion, Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
If you are not using Lion, Mountain Lion, or Mavericks then use the following procedure:
Resetting your Mac's PRAM and NVRAM
Intel-based Macs: Resetting the System Management Controller (SMC)
Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Reinstall OS X without erasing the drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1. -
My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?
My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?
Yes if your model MBP has a removable battery. If it does not:
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
http://support.apple.com/kb/HT3964 -
My MacBook pro won't turn on! Help?!
My MacBook Pro is less than a year old. When I went to plug it in this morning though, It wouldn't turn on! I tried plugging it in but the charger light went from green immediately to red. I left it plugged in for an hour but it still wouldn't work. The screen is completely black and there is no sound at all. Please help!!
What to do if your Mac won’t power on
First, try plugging in your Mac to allow the battery to charge. If it is not a portable Apple computer, skip this step. Wait a few minutes, and then try powering on the computer.
Next, try resetting your SMC.
Resetting the SMC of an Intel-based portable Mac with a battery you should not remove on your own
Note: This will not delete any data.
The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
On the built-in keyboard, press the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
Release the (left side) Shift (⇧), Control (⌃), and Option (⌥) keys and the Power Button at the same time.
Resetting the SMC of an Intel-based Mac Pro, iMac, Mac mini, or Xserve
Note: This will not delete any data.
The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Unplug the computer’s power cord.
Wait fifteen seconds.
Attach the computer’s power cord.
Wait five seconds and then press the power button to turn on the computer.
Resetting the SMC of an Intel-based portable Mac with a removable battery
Note: This will not delete any data.
The SMC is responsible for controlling various system functions. None of your data will be deleted by resetting the SMC.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Plug in the MagSafe power adapter into a power source and then connect it to your Mac if you have not already done so.
Remove the battery.
Press and hold the Power Button for 5 seconds.
Release the Power Button.
Reconnect the battery and the MagSafe power adapter.
Press the Power Button to turn on the computer.
Next, try resetting the NVRAM/PRAM.
Resetting the NVRAM/PRAM
Note: This will not delete any data.
The NVRAM/PRAM stores information such as speaker volume, screen resolution, startup disk selection, and recent kernel panic information (if any). You should reset the NVRAM/PRAM if you experience issues relating to these functions.
Shut down the computer by going to Apple () > Shut Down…
Select Shut Down or allow the computer to shut down automatically.
Turn on the computer by pressing the Power Button.
On the built-in keyboard, press and hold the Command (⌘), Option (⌥), P, and R keys before the gray screen appears.
Continue to hold down the keys until the computer restarts and you hear the startup chime for the second time.
Release the keys on the built-in keyboard.
If your computer still does not power on
Make an appointment with an authorized Apple service center or by making an appointment at the Genius Bar by going to this link:
http://www.apple.com/retail/geniusbar/
I hope I helped. -
I'm having an issue with turning my MacBook pro on. It's fully charged and when I press the power button I hear a disk chime but nothing happens on the display. Can anyone help please?
Tried connecting the cable? Still won't start?
If you are still under warranty and/or have AC, call them & let them deal w/it.
OOW: Take the MBP to your local AS or an AASP. Diagnostic testing is FREE!
http://support.apple.com/kb/TS1365 Intel-Based Apple Portables: Troubleshooting a computer that will not power on -
Help - MacBook Pro won't turn on
Help - my macbook pro will not turn on even though it is plugged in. Holding down the power button is ineffective. The power cord has the green "charged" light, but when I plugged it in, it wasn't charged and never did charge (the light never was orange). The computer worked perfectly this morning.
Will it not turn on at all or do you just get a gray screen?
If a gray screen, look at this:
https://discussions.apple.com/docs/DOC-5282
If it does not turn on at all, try a SMC reset:
http://support.apple.com/kb/ht3964
If the reset fails to bring life to the MBP, make an appointment at an Apple store genius bar for a free evaluation.
Ciao. -
MacBook Pro won't turn on and just beeps. What's wrong?
My Mac book pro won't turn and instead continues to beep three times, pause and repeats itself. What's wrong?
3 beeps is a RAM problem.
you can try resetting the SMC and PRAM and see if it helps
Or reseat the RAM
or run the AHT
Genius reservation http://www.apple.com/retail/geniusbar/
check warranty https://selfsolve.apple.com/agreementWarrantyDynamic.do
Maybe you are looking for
-
I had my iPod synced with iTunes on my iBook (OS 10.4.11) and then the iBook crashed and I had to replace it with a MacBook Pro (OS 10.6.8). I want to transfer all of the stuff on my iPod to my iPhone 4S through the MacBook Pro. But, I do not want
-
My desk-top is an iMac G5. I use the Firefox brouser exclusively on it and have for a number of years. I now have an iPad [#1] but it only has Safari as a brouser. When I "Sync" my iPad with my iMac it brings my "old" Safari bookmarks list to the iPa
-
IBook, 23" Cinema Display and a G4 DP 867
I'm trying to make a iBook 12" work with the 23" Cinema Display without the use of a VGAtor. I was thinking I could run it through the G4 DP 867 using one of Apple's apps. Can this be done?
-
In Preview I can drag several individual PDF pages into it to create a multiple page document. However, when I try to save, export or print this combined document, all I get is the first page. When I close the document, I lose all of the work I spent
-
I need to copy the data files to a SAN and want to change the number of data files form 4 to 1. This is only a small database (22Gb). I don't know how to delete the data files and re create them. Regards Hans