MacBook Pro. Wont turn on and beeping.

My MacBook Pro screen turned several different colors and began beeping. I shut it off and now when I try to turn it on it beeps and the power light flashes. HELP

If an SMC reset does not help, make an appointment at an Apple store genius bar:
http://support.apple.com/kb/HT3964
Ciao.

Similar Messages

  • My macbook pro wont turn on and is making a bleeping noise

    my macbook pro wont turn on and is making a bleeping noise

    the following article addresses startup tones and beeps for the mac:
    http://support.apple.com/kb/HT2538
    also try doing SMC reset:
    http://support.apple.com/kb/HT3964

  • MacBook Pro not turning on and beeping?

    Help. my MacBook Pro 2010 was just working fine and it randomly shut down. I felt it hot on the bottom. I googled it and said my ram was loose so I tried putting back in and it's still beeping away. I tried pulling the battery out and putting it back in and it's still beeping. I need help. the light on the bottom right flashes as it beeps. it beeps then pauses for about 5 seconds. and beeps again repeatedly. the beep sequence is beep.... beep.... beep... beep..
    help me please. thanks in advanced.

    http://support.apple.com/kb/HT1547 
    1 beep = no RAM installed
    2 beeps = incompatible RAM types
    3 beeps = no good banks
    4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
    5 beeps = processor is not usable

  • My MacBook Pro wont turn on and I can't figure out why...

    Does anyone know what can be wrong with my Mac Book Pro if I attempt to turn it on and it has a grey screen with a small apple and turns off on its own?

    First try the steps in this knowledge base article.

  • My MacBook Pro wont turn on and is plugged into the charger

    My MacBook was frozen for a second and after I closed the computer and reopened it, it looks as if it is off and won't turn back on. Nothing is lighting up. Please help!

    If you are able, try resetting the SMC. If that does not work, take it in for diagnosis.
    Barry

  • My MacBook Pro will turn on and get to the login screen. After I login though it goes to a white screen.

    My MacBook Pro will turn on and get to the login screen. After I login though it goes to a white screen.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • My one day old MacBook pro just turned off and it won't come back on either through mains or battery power

    My one day old MacBook pro just turned off and it won't come back on either through mains or battery power it's as if the unit is completely dead. Even with the mains plugged in there is no green or orange light to say its charging or full charged. The battery was fully charged anyway seconds before the screen went off.

    When you say no green or orange light are you refering to the little led on the magsafe connector?  That could mean either the charger/cable are bad or the circuitry in the MBP is faulty.  Since this is a brand new MBP best bet is to take it back to an Apple Retail store and have the genius bar staff take a look.  They can determine if it needs to be reparired or replaced.

  • MacBook Pro wont turn on; But fan is spinning?

    MacBook Pro wont turn on; But fan is spinning
    Already tried reseting the
    p-ram
    SMC
    Removing the:
    ram
    battery
    hard drive
    MacBook Pro 13in- 2010

    your screen may be broken connect an external monitor. 

  • Macbook Pro - WiFi turns OFF and won't turn back ON

    Hello,
    this is my first time posting something on this forum; I will be as detailed as possible. I bought a Macbook Pro back in 2011 and It came with Lion OS. Last year I upgraded it to Mavericks and so far it has been a nice experience. However, in the past week I have experienced a very strange and irrating problem with my macbook. While doing work all of the sudden the WiFi would turn off and lose all connection to the web. I attempted to turn it back ON by clicking on the wifi signal icon but something weird occured, it was still 'ON' according to my mac and the only option available was to actually turn it OFF, so i clicked on it and the icon would go empty with no curvy lines (i attached a picture). Then i clicked again on the icon to turn it back on, however, as was doomed to remain in this state cause no matter what I tried.. the wifi will remain off even after clicking on the 'turn wifi on' option multiple times. I tried going to the assist me option under network preferences and I obtained multiple results with no fix. I tried sending my mac to sleep though at first seemed to fix the problem.. the wifi inmediately went back to being off and wont catch a signal. The only thing that fixes this is a fresh restart which is annoying and unacceptable...this is really annoying and I need a solution asap because this problem is become very frequent (once every 2 hours)... any help will be appreciated it.
    I attached 2 pictures and the console log when this happened.
    1. A picture of my assist me window before i sent it to sleep, shows the WiFi on the left with the 'Failed' (which confuses me). it also shows the wifi icon empty ( like it was off) but the computer shows as if it was on and would ask you to turn it off... weird?
    A second picture after I sent my mac to sleep. Though it seems like there was no wifi signal available, the router was on and literally next to my mac...but my machine wont catch up the signal. (other devices were connected to the wifi and have no problem with it).
    Here is the console log right before and after my this problem occured:
    3/11/14 1:07:04.000 AM kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=10415[GoogleSoftwareUp] final status 0x0, allowing (remove VALID) page
    3/11/14 1:09:53.500 AM Dock[1091]: CGSSetWindowTransformAtPlacement: Singular matrix [inf 0.000 0.000 inf]
    3/11/14 1:11:19.322 AM WindowServer[83]: disable_update_timeout: UI updates were forcibly disabled by application "BitTorrent" for over 1.00 seconds. Server has re-enabled them.
    3/11/14 1:11:23.445 AM BitTorrent[10434]: *** WARNING: -[NSImage compositeToPoint:operation:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    3/11/14 1:11:23.445 AM BitTorrent[10434]: *** WARNING: -[NSImage compositeToPoint:fromRect:operation:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    3/11/14 1:11:26.820 AM WindowServer[83]: common_reenable_update: UI updates were finally reenabled by application "BitTorrent" after 8.50 seconds (server forcibly re-enabled them after 1.00 seconds)
    3/11/14 1:13:19.619 AM WindowServer[83]: disable_update_timeout: UI updates were forcibly disabled by application "System Preferences" for over 1.00 seconds. Server has re-enabled them.
    3/11/14 1:13:20.899 AM WindowServer[83]: common_reenable_update: UI updates were finally reenabled by application "System Preferences" after 2.28 seconds (server forcibly re-enabled them after 1.00 seconds)
    3/11/14 1:13:27.833 AM System Preferences[10444]: AVF error: Perf capability check failed: 0xe00002bc
    3/11/14 1:13:27.834 AM System Preferences[10444]: AVF error: Branch_QT0::pushBits, Context Creation Failed.
    3/11/14 1:14:47.736 AM WindowServer[83]: _CGXHWCaptureWindowList: No capable active display found.
    3/11/14 1:19:37.821 AM WindowServer[83]: _CGXHWCaptureWindowList: No capable active display found.
    3/11/14 1:22:31.000 AM kernel[0]: MacAuthEvent en1   Auth result for: 60:c3:97:04:d5:b8  MAC AUTH succeeded
    3/11/14 1:22:31.000 AM kernel[0]: wlEvent: en1 en1 Link UP virtIf = 0
    3/11/14 1:22:31.000 AM kernel[0]: wl0: Roamed or switched channel, reason #8, bssid 60:c3:97:04:d5:b8
    3/11/14 1:22:31.000 AM kernel[0]: en1: BSSID changed to 60:c3:97:04:d5:b8
    3/11/14 1:22:31.000 AM kernel[0]: AirPort: RSN handshake complete on en1
    3/11/14 1:25:29.779 AM loginwindow[44]: magsafeStateChanged state changed old 2 new 1
    3/11/14 1:25:32.778 AM parentalcontrolsd[10493]: StartObservingFSEvents [849:] -- *** StartObservingFSEvents started event stream
    3/11/14 1:25:34.241 AM xpcproxy[10494]: assertion failed: 13C64: xpcproxy + 3438 [D559FC96-E6B1-363A-B850-C7AC9734F210]: 0x2
    3/11/14 1:28:50.334 AM WindowServer[83]: disable_update_timeout: UI updates were forcibly disabled by application "System Preferences" for over 1.00 seconds. Server has re-enabled them.
    3/11/14 1:28:50.425 AM com.apple.preference.network.remoteservice[10511]: assertion failed: 13C64: liblaunch.dylib + 25164 [38D1AB2C-A476-385F-8EA8-7AB604CA1F89]: 0x25
    3/11/14 1:28:50.442 AM com.apple.preference.network.remoteservice[10511]: assertion failed: 13C64: liblaunch.dylib + 25164 [38D1AB2C-A476-385F-8EA8-7AB604CA1F89]: 0x25
    3/11/14 1:28:51.249 AM com.apple.preference.network.remoteservice[10511]: Bogus event received by listener connection:
    <error: 0x7fff7e218b50> { count = 1, contents =
    "XPCErrorDescription" => <string: 0x7fff7e218e60> { length = 18, contents = "Connection invalid" }
    3/11/14 1:28:52.237 AM WindowServer[83]: common_reenable_update: UI updates were finally reenabled by application "System Preferences" after 2.90 seconds (server forcibly re-enabled them after 1.00 seconds)
    3/11/14 1:28:52.401 AM com.apple.preference.network.remoteservice[10511]: Could not find image named 'InvalidDataIcon'.
    3/11/14 1:28:52.526 AM com.apple.preference.network.remoteservice[10511]: *** WARNING: -[NSImage compositeToPoint:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    3/11/14 1:28:52.526 AM com.apple.preference.network.remoteservice[10511]: *** WARNING: -[NSImage compositeToPoint:fromRect:operation:fraction:] is deprecated in MacOSX 10.8 and later. Please use -[NSImage drawAtPoint:fromRect:operation:fraction:] instead.
    3/11/14 1:29:02.894 AM WindowServer[83]: window ac1 is already attached to window abe
    3/11/14 1:29:07.775 AM WindowServer[83]: _CGXGetWindowOrderingGroup: Operation on a window 0xac1 requiring rights 0x5 by caller System Preferences
    3/11/14 1:29:11.433 AM WindowServer[83]: window ac5 is already attached to window abe
    3/11/14 1:29:12.861 AM WindowServer[83]: _CGXGetWindowOrderingGroup: Invalid window 0xac5
    3/11/14 1:29:13.000 AM kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    3/11/14 1:29:13.113 AM configd[19]: SCNC: stop, triggered by (19) configd, type PPPSerial, reason Service Disposed
    3/11/14 1:29:13.000 AM kernel[0]: en1: BSSID changed to 60:c3:97:04:d5:b8
    3/11/14 1:29:13.200 AM configd[19]: network changed: v4(en1-:192.168.2.15) v6(en1-:2002:32ac:2b50:1234:62c5:47ff:fe93:4f3a) DNS- Proxy-
    3/11/14 1:29:13.464 AM UserEventAgent[11]: Captive: CNPluginHandler en1: Inactive
    3/11/14 1:29:14.000 AM kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    3/11/14 1:29:14.274 AM netbiosd[10316]: network_reachability_changed : network is not reachable, netbiosd is shutting down
    3/11/14 1:29:17.000 AM kernel[0]: en1: BSSID changed to 60:c3:97:04:d5:b8
    3/11/14 1:29:19.000 AM kernel[0]: en1: BSSID changed to 60:c3:97:04:d5:b8
    3/11/14 1:29:19.000 AM kernel[0]: en1: BSSID changed to 60:c3:97:04:d5:b8
    3/11/14 1:29:21.488 AM WindowServer[83]: window ac8 is already attached to window abe
    3/11/14 1:29:30.829 AM configd[19]: subnet_route: write routing socket failed, Network is unreachable
    3/11/14 1:29:32.747 AM configd[19]: network changed: Proxy
    3/11/14 1:29:37.338 AM CalendarAgent[188]: [com.apple.calendar.store.log.caldav.queue] [Adding [<CalDAVAccountRefreshQueueableOperation: 0x7faef96a4140; Sequence: 0>] to failed operations.]
    3/11/14 1:29:37.356 AM CalendarAgent[188]: [com.apple.calendar.store.log.caldav.queue] [Account refresh failed with error: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7faefb829e00 {NSUnderlyingError=0x7faef9575860 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://hyddro%[email protected]/1362164150/principal///hyddro%[email protected]/1362164150/principal/, NSErrorFailingURLKey=https://hyddro%[email protected]/1362164150/principal///hyddro%[email protected]/1362164150/principal/, AccountName=iCloud, CalDAVErrFromRefresh=YES, NSLocalizedDescription=The Internet connection appears to be offline.}]
    3/11/14 1:30:10.259 AM WindowServer[83]: _CGXGetWindowOrderingGroup: Operation on a window 0xac8 requiring rights 0x5 by caller System Preferences
    3/11/14 1:30:12.162 AM WindowServer[83]: window acc is already attached to window abe
    3/11/14 1:30:18.054 AM WindowServer[83]: _CGXGetWindowOrderingGroup: Invalid window 0xacc

    Thank you for your detailed troubleshooting attempts.  Very helpful.  Sorry, I cannot read "logs."  My eyes just glass over on those things.  Hopefully, a knowledgeable user will come along shortly to decipher for you.
    I noticed from the pics that your location setting is "untitled."  Have you tried the "Automatic" setting?  Run the diagnostic test?  Results?
    Try the basics first:
       Change your router channel number.  Most times this works & is all you have to do.
    Disconnect & reconnect your modem.  unplug it for about 10 seconds.  Plug it back in.  Do the same for Apple’s routers.  Wait for everything to reboot.
    System Preferences>Network
    Click the Assist Me button.
    In the next window that pops up, click the Diagnostic button & do the necessary.
    Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer.   See these basic networking KB Articles:  http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
    http://support.apple.com/kb/HT4628  Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
    Manually provided DNS server addresses are higher priority than DHCP's
    http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
    ============================
    What to do when you can't connect to the Internet
    Also, run the Airport Utility app which is located inside the Utilities folder.
    =====================
    If using a  Linksys router, contact LinkSys Customer Support and/or post in their forums.
    If using Apple's Airport, please re-post over in one of the AirPort Forums.

  • My macbook pro wont do anything and it is just blowing air out the back

    my macbook pro wont do anything it is using its fan rapidly

    Try Reseting the PRAM, It should fix the Problem.
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
        Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
    http://support.apple.com/kb/HT3964

  • Macbook pro wont start with 3 beeps

    hi
    Few months back I purchased a refurbished macbook pro (late 2012 model) with i7 processor and 8 GB ram. Now after 2 months I experienced problem with mac - it wont start with 3 beeps. I looked at different articles in net and found about no memory bank problem. I opened the back and changed slots and it seemed to fix the issue. However the issue was recurring few times and ram was changed. Again the issue seemed to have resurfaced. I tried with memtest in single user mode and RAM passes the tests.
    What else could be the issue around the macbook pro. Do you suggest taking it to local Apple store to get it checked?
    Thanks

    Test each module installed alone while switching slots (power down before switching and remove battery.) Do both modules work alone in each slot? If they do, then it would appear the memory is good as are the slots. So, something else is at play and only an Apple Store has the equipment to go further - make a Genius Appointment and take it in for service.

  • Macbook Pro Wont turn on HELP?

    I turn on my macbook pro on and the the fans will turn on then a second later turns off with a light beep. The keyboard nor screen are lighting up.. Help?

    One beep means the machine couldn't find the RAM.
    https://support.apple.com/kb/HT2341
    Service call.

  • Macbook Pro wont turn on - sometimes

    I have mid-2009, 13 inch Macbook Pro. Recently I am noticing trouble. Once in a while when I put it to sleep by closing the lid, the light stays lit (which is suppose to go on and off indicating sleep). And when I open the lid, there is nothing on the screen and the light goes away. I close the lid, again the light lits up and stays up. So the macbook wont turn on.
    Does anyone have any idea why is this? I sometimes keep the power button pressed for 5-6 seconds and force shutdown and boot again and then it works. Is it a good idea? is there any other way in these situation?
    Is there something wrong in the hardware?
    Please help ...

    Sachadon,
    Welcome to Apple Discussions.
    When you try to wake your computer when opening the lid have you tried tapping one of the keys on the keyboard to wake it?
    If that does not work then try doing a SMC reset follow these instructions.
    SMC RESET
    It is possible you are having hardware problems with the lid sensor but let try some other steps first.
    Regards,
    Roger

  • New Macbook Pro Wont turn after discharge

    Hello everyone,
    I just purchased my 3rd mac in the past 2 years, yeah that's how hooked I am, now windows free 99% and love it...
    My brand new macbook pro has a very annoying issue.. if I use it on battery power and it discharges completely I have to wait up to 15 minutes after connecting it to power to be able to turn it back on again. this is so frustrating as I am sometimes doing some work and have to get away from the computer for a few minutes.. If it discharges within that time and I come back to continue my work guess what.. I need to wait all this time even after connecting it to power to resume my work...
    Does anyone has the same problem? is this normal? I've searched google and haven't found the same problem on anyone else unless they are OK with that and just don't report it... I've never had this problem with any other laptop I own and is extremely annoying, my wife's macbook doesn't do that, if it discharges and goes to sleep you can just connect the magsafe adapter and it will come right back up.
    your comments will be greatly appreciated.

    My MBP has always come back immediately. So has my old iBook. I rarely discharge my battery completely, but will do so on occasion to calibrate it. But I have never had the problem you describe. My personal opinion is that the long delay is definitely not normal.
    Out of curiosity, next time your Mac shuts down like this, remove the battery and see if it will start up immediately. If it does, you could possibly have a faulty battery. If it still takes a lot of time to start up with the battery removed, there is something else wrong. I have never heard of anything quite like this. Since you didn't mention excessive heat, that wouldn't be a factor.
    Be sure you can reproduce the condition for the Apple genius. They have to see it to be able to do anything. Go in a bit early with a low battery and run it out in the store, so you can show them exactly what it is doing.
    Good luck!

  • My 4month old Macbook pro wont turn on unless plugged in, but remains on after unplugged.

    I got a brand new macbook pro 4months old.  What happens is it does not turn un unless it is plugged in when I unplug it though it is fine and will run till it dies, BUT if I were to close it and put it to sleep it will not turn back on. I would have to plug it back in and turn it on then I can unplug it and it will be fine till it falls back asleep.
    Once I do turn it back on, a pop up says that I need to re adjust the clock and another trying to search for the internet, even if I was already connected with is 5 min ago. Even apps like tweetdeck and facbook would reset and I would have to enter all my information again, where as before it would just remain there.
    I have NO idea why it is like this and I am not really familiar with a Mac and its OS but any information would be greatly appreciate!
    Thanks!
    Yoshi

    Bring it to an Apple store or AASP. You are under warranty.

Maybe you are looking for

  • Error while upgrading to maverick and computer hung while reverting back to old OS

    While installing OS maverick, I got an error message on something about recovery file or something not being installed. It gave me an option of restarting the old OS (mountain lion) and after I clicked the button, my computer is now not starting up.

  • HP 470wbt Comparable Network Adapter ???

    The HP store no longer supplies the HP 802.11 adapter for this printer and I have been shopping around online to find one that will work with this printer.  HP recommends HP 802.11 B/G WIRELESS PRINTER ADAPTER.   Can I use in its place any of these m

  • CRM-GATP Integration

    Hello Gurus, I'm configuring CRM-GATP integration in our server. I'm facing few challenges while doing so. CRM team has configured customized transaction types & Item categories in CRM. These ord types & item categories do not exist in ECC system. Al

  • Speeding up spaces: How to disable the transition animation?

    Is there some way the disable the Spaces transition animation? I would like to change between the different virtual desktop as fast as possible. There are some times when it gets quite annoying: when you move to other spaces the screen flickers if th

  • Can't upgrade Aperture 3.2.4 in Maverick - lost serial number

    I have the 3.2.4 version of Aperture which was running perfectly until I installed maverick. Now there is a NO sign on the Aperture icon and if I try and udate the software from the main menu it doesn't work. I don't have the serial number - I probab