Macbook shutdown without any warning after 40%, when run on battery.

Hello,
My Macbook when run on battery after 40% shuts off without a warning. Is there a way to avoid it? Is there a setting in the battery preferences where I can change to avoid shut down?
Battery Information:
Model Information:
Serial Number: DP-ASMB016-370e-4db1
Manufacturer: DP
Device name: ASMB016
Pack Lot Code: 0002
PCB Lot Code: 0000
Firmware Version: 102a
Hardware Revision: 0500
Cell Revision: 0200
Charge Information:
Charge remaining (mAh): 2496
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 4276
Health Information:
Cycle count: 142
Condition: Good
Battery Installed: Yes
Amperage (mA): 1488
Voltage (mV): 12281
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 60
Disk Sleep Timer (Minutes): 180
Display Sleep Timer (Minutes): 45
Automatic Restart On Power Loss: Yes
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 60
Disk Sleep Timer (Minutes): 180
Display Sleep Timer (Minutes): 45
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: Yes
If you can suggest me with the above problem will be of great help. Thank you in advance.

Same issues here:
- When powering the MB on the battery, the MB can go off suddenly without warning, usually at about 20% but, since it started about 2 months ago, it occurred also at 7%, between 30 and 40% and even 70% once… It occurs every time when on batteries. And every time, if I start the computer again, it will shut down suddenly without warning after a few seconds/minutes. When back on mains, it can be powered on normally. It does not go to sleep, it's a complete and sudden power off without warning.
- The battery at about 173 cycles sees its capacity dwindling way too much (it's been dwindling since day one, but it's going down faster and faster, the graph since November 2007 in MiniBatteryLogger is edificatory). The capacity right now is between 2900 and 3460 depending of the feel of the day. It's been calibrated regularly since day one in July 2007. Note that the capacity dwindled from its original capacity but never went higher than this value even if along the way it recovered sometimes more capacity.
I have tried all the tricks from calibrating a little bit more often, reseted the SMC, even a complete system reinstall (that I wanted to do anyway as I had to get rid of the evil spotlight bug). All this to no avail.
So what? :-/
Model Information:
Serial Number: DP-ASMB013-3629-1bbc
Manufacturer: DP
Device name: ASMB013
Pack Lot Code: 0001
PCB Lot Code: 0000
Firmware Version: 0102
Hardware Revision: 0300
Cell Revision: 0200
Charge Information:
Charge remaining (mAh): 3320
Fully charged: Yes
Charging: No
Full charge capacity (mAh): 3412
Health Information:
Cycle count: 173
Condition: Check Battery
Battery Installed: Yes
Amperage (mA): -1
Voltage (mV): 12411
System Power Settings:
AC Power:
System Sleep Timer (Minutes): 0
Disk Sleep Timer (Minutes): 0
Display Sleep Timer (Minutes): 5
Automatic Restart On Power Loss: No
Wake On AC Change: No
Wake On Clamshell Open: Yes
Wake On LAN: Yes
Display Sleep Uses Dim: Yes
Battery Power:
System Sleep Timer (Minutes): 5
Disk Sleep Timer (Minutes): 10
Display Sleep Timer (Minutes): 1
Wake On AC Change: No
Wake On Clamshell Open: Yes
Display Sleep Uses Dim: Yes
Reduce Brightness: Yes
Hardware Configuration:
UPS Installed: No
AC Charger Information:
Connected: Yes
Charging: No

Similar Messages

  • HP Probook 4540s Sudden Shutdown Without any Warning

    I have a HP Probook 4540s laptop bought in November 2012. It has Core i5-3210M CPU @ 2.50 Ghz chip with 8 gb ram and 500 GB hard disk. Till 2014 it was all OK. But now it has started giving me problems like it shut downs when it is at low battery say just about to reach 10 %. No low battery message just complete shut down(bam, screen goes dark). Now I have done the following steps
    1. Battery has been calibrated it did solve the problem but it again started to happen.
    2. I got my laptop's fan replaced 28 days back on i guess Jan 5, 2015 and vents are clean
    3. I use Hardware Monitor Software to monitor the temperature and the results are as follows :
              >> During Normal Operations it remains between 50 to 55 C (is it Normal ?) What should be the ideal temperature ?
              >> Hard Disk temp is 60 to 64 C.
    4. I use battery saver mode and everything set to normal
    5. Drivers and BIOS Updated
    6. Used HP Support Assistant to check battery health it shows OK.
    7. I have changed the values also like I set the critical level,low battery and reserve battery but i guess that also not working.
    Now My Question is 
    1. Is it due to overheating ? During normal operations like when plugged in it doesn't shutdown. Works Perfectly.
    2. Or the battery is giving me trouble and needs to be replaced. After 100% charge it gives me around say 1 hr 30 mins of use but when it is about to hit  11 or 10% the system shuts down. 
    Please provide me with a solution
    P.S. I don't use my laptop for gaming

    Deep.
    Download and run BatteryMon.
    http://download.cnet.com/BatteryMon/3000-2094_4-29244.html
    After download click on start.
    In the upper left hand corner you will see a battery tab click on it to get the details of the battery.
    Look at Design Capacity,  Full Charge Capacity and Current Capacity.
    Let us know what you find.
    REO
    HP Expert Tester "Now testing HP Pavilion 15t i3-4030U Win8.1, 6GB RAM and 750GB HDD"
    Loaner Program”HP Split 13 x2 13r010dx i3-4012Y Win8.1, 4GB RAM and 500GB Hybrid HDD”
    Microsoft Registered Refurbisher
    Registered Microsoft Partner
    Apple Certified Macintosh Technician Certification in progress.

  • Satellite A30 always shutdown without any prior warning

    Hi all,
    i'm having a problem with my Satellite A30 notebook. It will always shutdown without any prior warning. But the thing is i don think its a heating issue with the fans. The notebook will only shut down if im running the laptop on high power or on full power by the AC adapter. Tasks that may be taxing like full system virus scan or playing games will cause it to shutdown after about 20 minutes again only on high battery power setting or if its connect to mains and is set on full power. Using word or simple tasks do not affect it.
    Now im thinking there may be a problem with my cpu as it cannot handle it when it has to perform advanced tasks on my notebook. What could the problem be?? On low power my notebook will work fine even when its performing these advanced tasks it's only a problem when its on full or high power.
    Any help/advice?

    Hi
    Thanks for the description I'm still thinking its a overheating problem.
    The notebook power saver controls different power modes if the notebook runs with AC adaptor or with full power the power saver uses different power mode as when the notebook will run with battery only.
    The different power modes support different CPU settings and different cooling method.
    Probably the CPU runs with full performance and getting hot when the AC adaptor is connected.
    I think you should check the cooling modules and fans. Try to clean it carefully with vacuum cleaner. But if you have no experience with such procedures then asks a technician or someone with more experience

  • Macbook Shuts downs without any warning.

    Hi All,
    Recently I have noticed that my Macbook shuts down without any warning when the battery is out of power. Previously i used to get a warning when about 9-10 mins of power was left.
    I have all the updates installed. Also I have not installed any new hardware.
    Is there any settings in the System Preferences. What should I do to correct this situation.
    Best,
    Siva
    Battery Information:
    Battery Installed: Yes
    First low level warning: No
    Full Charge Capacity (mAh): 4600
    Remaining Capacity (mAh): 3580
    Amperage (mA): 1542
    Voltage (mV): 12220
    Cycle Count: 113

    I'd try a SMC reset - that usually clears battery/power related settings and might do the trick.
    Blackbook C2D   Mac OS X (10.4.9)   120Gig, 1Gig, Superdrive.

  • Turn off suddenly without any warning when plugin Adapter(Charger)

    My Pavillion dv6-3208tx turn off suddenly without any warning when plugin Adapter(Charger) and it won't start unless i unpluged the adapter. I can run on battery. Pliz help...!

    Make sure the keyboard is seated properly.
    (Instructions can be downloaded here.)
    Sometimes, plugging in the adapter when the keyboard is improperly seated can cause this behavior.

  • I have big problem with battery, It's not working good just two hours and stop without any warning when the battery in 50% then reach 30% in the same moment, then the iphone stopped,what I can do for that and I live in Egypt???any help

    My Iphone 4 is very good until last Thursday, I used it from sep 2011 without any problems, My problem is the battery is down without any warning and working after 100% then 82% then 50% then 30% and down these things throw less than two hours
    what can I do with that??
    Also, I live in Cairo,Egypt
    waiting your recommendations

    Hi,
    "But it didn't work it's just turning them to black gray scale colors not what i was thinking about."
    If you want it to be colored, you'll need to create a color-palette for the 8bppIndexed bitmaps. The keyword for this process is "Color-Quantization".
    The whole yellow-green pie you get is from the wrong format. If you convert the 32bpp bitmaps to 24 bpp bitmaps, you loose the alpha channel ("transparency"). You can manually set one color to "transparent" with the mMakeTransparent-method
    of the Bitmap class, or simply use gif-images (they are 8bpp with a transparent "key"-color)
    Regards,
      Thorsten

  • HP 250 Laptop - When running on battery turns off without warning and won't restart

    One month after warranty expires this laptop presents with this problem. It shuts down without warning when running on battery, although the battery has plenty of charge. Following shutdown it won't restart on battery. Plugging in power and restarting it displays a message that the battery is cactus before continuing to boot. When trying to run F2 on startup battery check it simply doesn't progress past the initial screen (1%) and [esc] key does nothing. Need to power off. However, REMOVE the battery, boot the computer, shutdown, REINSTALL the battery, turn on and everything is OK - most recent example showing battery with 95% remaining. Continues to work for a few days until it decides to fail again. Suspect the battery is not at fault here, and in any case can't get a replacement (thanks HP for providing equipment with rare and unusual parts) - one supplier has only two on order which will be delivered some time in September!! Usual third party providers don't provide a replacement for this battery. Have seen a lot of references to this sort of mystery "battery failure - shutdown with warning" but no concrete solution. Have tried different power setting including never hibernate, but these seem unrelated. Open to useful suggestions at this point. 

    One month after warranty expires this laptop presents with this problem. It shuts down without warning when running on battery, although the battery has plenty of charge. Following shutdown it won't restart on battery. Plugging in power and restarting it displays a message that the battery is cactus before continuing to boot. When trying to run F2 on startup battery check it simply doesn't progress past the initial screen (1%) and [esc] key does nothing. Need to power off. However, REMOVE the battery, boot the computer, shutdown, REINSTALL the battery, turn on and everything is OK - most recent example showing battery with 95% remaining. Continues to work for a few days until it decides to fail again. Suspect the battery is not at fault here, and in any case can't get a replacement (thanks HP for providing equipment with rare and unusual parts) - one supplier has only two on order which will be delivered some time in September!! Usual third party providers don't provide a replacement for this battery. Have seen a lot of references to this sort of mystery "battery failure - shutdown with warning" but no concrete solution. Have tried different power setting including never hibernate, but these seem unrelated. Open to useful suggestions at this point. 

  • Laptop shuts down without any warning

    My laptop is shutting down without any warning. It has done so twice. When I run the preboot diagnostic, everything is fine. When I run Dell Support Assist app, this is the error message that I got from the System History:
    Application Error
    Fault bucket 86066676302, type 4
    Event Name: APPCRASH
    Response: Not available
    Cab ld: 0
    Problem signature:
    Pl: DllHost.exe
    P2: 6.3.9600.17415
    P3: 54504134
    P4: StackHash_216b
    P5: 6.3.9600.17736
    P6: 55014336
    P7: c0000374
    P8: PCH_CF FROM_ntdll+0x000000000009177A
    P9:
    P10:
    Attached files:
    C:\Users\Raymond\AppData\Local\Temp\WER6C2E.tmp.WERInternalMetadata.xml
    These files may be available here:
    C:\Users\Raymond\AppData\Local\Microsoft\Windows\WER\ReportArchive\AppCrash_OUHost.exe_fcb15f1d8bcda961763f8dc9a8f899f8621977b_30a79b3d_14cf863e
    Analysis symbol:
    Rechecking for solution: 0
    Report 10: toala596-eca4-11e4-bfac-08edb9244ef6
    Report Status: 0
    Hashed bucket: 7b43e3b419dd3feaa74b55be5e190271
    These files may be available here:
    C: \Users\Raymond\AppOata \Local\Microsoft\ Windows\ WER\ReportArchive
    \AppCrash_OUHost.exe_fcb15f1d8bcda961763f8dc9a8f899f8621977b_30a79b3d_l4cf863e

    Hi ,
    Thank you for writing to the Dell Community Forum.I am Jennifer and I work for the Dell Social Media Team .
    To assist me to resolve this issue I would suggest you to try these steps and advise the result ,
    *)Is this issue seen with all applications and any particular applications.
    *)When the system crashed did you experience any over heating issue.
    *)May I know the operating system installed on the system .
    *)Would suggest you to work on this system in safe mode with networking then test if the same issue is seen .
    *)Also as you mentioned that with the preboot diagnostic the system passed all the test so  the system's hardware is working fine.
    If there are any more queries do reply to this post with the system model ,operating system installed on the machine, service tag of the system(sent via private message) so that I can look into the details of the system and assist you better .
    Awaiting a reply from you .
    Kindest Regards,

  • PSE 9 reboots my machine without any warning message..

    I am using Photoshop elements 9. i brought it recently. And the installation went
    well.. but when i am using the software, my machine reboots without any warning message.
    My System Configuration:  INtel Pentium 2.19GH,  80GB Hard Disk and 2GB RAM. and operating system is XP.
    Please help me in this regard.. what needs to be done...???

    Hi,
    Since nobody else is coming up with ideas for your problem, I'll let you know my thoughts.
    As the system is suddenly rebooting, I tend to feel you might have a hardware problem. PSE 9 does use a lot of resource when it is working and could be causing the hardware to fail.
    Just a few questions first:
    1) how much free space on your disk drive?
    2) does the system reboot when using any other software?
    I have seen similar failures caused by overheating - sometimes a fan fails and needs replacing. Other causes could be a problem with the power supply unit - the extra processing load can sometimes cause the voltages to drop.
    Since you said about the screen becomes blurry sometimes, it could be that there is a problem with the graphics card.
    I'm not being rude, but how well are you with computers? If I were to ask you to check the event viewer, would you know what to do or would I have to give detailed instructions?
    Brian

  • SQL developer starts and then disappears without any warning

    Hi, guys:
    I need to use SQL developer where there are existing connections. however, SQL developer 3.1 asked the java.exe location, and I chose java 6, now I can launch SQL developer but not able to continue running it. SQL developer starts and then disappears without any warning. Could anyone help me on this problem?
    Thanks a lot!
    Sam

    Can you start the exe from the BIN subdirectory? That should open a command console, and maybe you can see any error messages there that explain what's happening. For step-by-step directions, here's some help:
    http://www.thatjeffsmith.com/archive/2012/06/how-to-collect-debug-info-for-oracle-sql-developer/
    OR
    Install SQL Developer to a new directory and run it from there and see if that helps you get around your current install's issue.

  • How I could tranfer files from my iPad to my MacBook Pro without any software?

    I never found a method how to do transfering files between iPad and MacBook Pro without any software.
    Exist some method?
    If you know how to do it, please help me as faster as you can!
    THANK YOUU!!

    Hi,
    Unfortunately general file transfer is not currently supported on iOS devices. If you have apps installed on your iPad that support file sharing, you can exchange files with these apps by connecting your iPad to your computer and selecting the Apps tab on the device's page in iTunes. If you scroll down here, you will find a list of apps, that support file sharing, and you can copy file to/from the particular app, but there's no way of accessing the iPad's file system without 3rd party software, and even if you use one, it will be able to access the file storage areas of the file system, but not the OS root folder. You need a jailbroken device to do that.
    iTunes also copies all your photos and videos from your devices. The only official way of moving file between iOS devices is with iTunes. If you consider iTunes a software (it is one) than there's absolutely no way for that, if your device is not jailbroken.
    Just to be clear, I'm against jailbreaking, because it makes your device vulnerable, and can create a lot of problems, that would not exist on a factory device.
    Hope this helps
    Regards,
    Gábor

  • Macbook Pro won't login after sleep (sleep with low battery -- mac turned off maybe it's called save sleep)

    Macbook Pro won't login after sleep (sleep with low battery --> mac turned off maybe it's called save sleep)
    So if I hit the powerbutton my mbp booted like it is booting from the save sleep (so very fast and the login screen is there in about 10 sec.and there is no apple logo while booting just the desktop screen in "unsharp" ore foggy however...)
    Then when i see the login (if the keyboard backlight turned on) i wand do tipe in my code but it won't work... the trackpad is not working; and when i plug-in a usb mouse the mbp is not powering on the usb-mouse (laser is off)
    Why is that this way?
    Is there n option to wake up the mbp fromm deep/save sleep without haveing issiues after that?
    THX

    Sorry for such a long delayed response...
    I was able to get to an apple store this past weekend, and let me tell you... I'm about finished with there great "support".
    Right before I went to the store, I tried to eject a disk. Well the cloth in the SuperDrive (I assume to protect the drive from dust and such) Pulled up with my disk. So I get the Apple store, describe my problem and what happened with the cloth piece. The "Genius" writes up a form and tells me they have to run diagnostic and it will take a couple days... and I will get a call when its done (1-3 days).
    Well on day number 3 I called up the store and they told me it was ready to be picked up? I asked if anything had been fixed and they told me they could not reproduce my "sleep issue", so they couldn't fix that.. but told me the cloth piece in the SuperDrive had been fixed.
    I drive an hour (one way) to the Apple store to find that all they did was PULLED OUT the cloth... they did not replace it! So basically I have a hole for a Super Drive.
    I asked why I was not called to say that my computer was ready to be picked up... didn't get an answer on that one.
    I asked why my SuperDrive was said to be fixed, when nothing was done... they told me that it would have to be sent out to the factory store for that to be fixed (FIRST TIME THEY MENTIONED THAT!) Oh, and that would take 5-7 business days. Well that's not going to happen right now considering I'm a college student that NEEDS a working computer!
    So I go home, angry... start just putting all my important documents back on the computer. And the screen starts blinking!!!! I guess now I have the same thing described in another post on these forms...
    Lets just say that I'm not very happy with Apple right now! If anybody else has success on either the sleep issue or the screen blinking issue, please let me know!
    Thank you!

  • Macbook Pro crashes when running on battery

    Hi.
    My Macbook Pro crashes when running in battery. It seems it doesn't happen when connected to the power.
    Is there any way to know if it's a battery malfunction?
    Because Apple changed the motherboard a month ago or so because Nvidia broke. So it could be also the connector to the battery?
    Is there any tests I can run?
    Thanks

    I would take it back to Apple and have them check it. You may have got a replacement logic board with a problem. Apple usually use rebuilt ones.
    Dave M.
    MacOSG Founder/Ambassador  An Apple User Group  iTunes: MacOSG Podcast
    Macsimum News Associate Editor  Creator of 'Mac611 - Mobile Mac Support'

  • My macbook pro 2.0 early 2011 will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

    Alo, my Macbook pro i7 2 GHz Intel Core i7 (early 2011) will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

    There is no output from that command line?   Maybe the pid changed.
    I'll repeat what I am trying to find out...
    1. You do a pmset -g on the terminal.
    2. The output from that pmset should have a line that says "sleep 0 (imposed by n)" where n is some number.
    3. The ps ax | grep n is supposed to display what the process associated with n is.
    It's the output from step 3 that should indicate what is causing you not to sleep.
    But speaking of sleep, that's where I am going.

  • My macbook won't turn it on when running by battery

    my 13" macbook won't turn it on when running by battery even the battery is completely charged. Even though plugging by power my macbook still works. What should I do to make sure the battery of the macbook to make it work again.

    You might try to reset the SMC and/or PRAM. If that doesn't help you should contact apple service about getting it replaced.

Maybe you are looking for

  • File will not open nor move to trash, and unexpectedly closes finder

    I downloaded a file and saved it in my movies folder on my mac book pro. When i click on the movies folder in finer it will automatically close finder down. If i search for the folder that i downloaded it appears but will not move to trash nor open,

  • Error creating appsutil.zip on RHEL5

    Hi all, I want to configure autoconfig follow link : http://www.in-oracle.com/Oracle-Apps/11i/migrate-autoconfig-DB.php but I have a problem when create appsutil.zip file. when i run "$perl $AD_TOP/bin/admkappsutil.pl" i got this error "environment n

  • Shippment details IDOC/BAPI

    Hi I am working on a project to bring shipments details to external system. Please let me know, how to send the shipment details from SAP to external system. If it is through IDOC, please let me know the IDoc type (there are SHPMNT01 to 05 available,

  • Crop sizing control

    How do I keep pictures I've cropped from enlarging mostly out of view (to fill the screen) when preparing and watching a slide show?

  • Progress Bar doesn't look correct in Windows 7

    I use a progress bar control and set ATTR_USE_PROGESS_BAR_VISUAL_STYLES attribute. It works perfect in Windows XP. The progress bar looks identical to Windows ones. Though now check how it looks in Windows 7. No matter either aero windows style is on