MacBook will not boot after iTunes 10.5.2, iPhoto, and Safari update

My MacBook (mid 2007) will no longer boot after the iTunes 10.5.2, iPhoto and Safari update. It will load Lion but will no open any applications. After running Repair Disk Permissions and Repair Disk in the Recovery HD, Lion will ask for my password, log in, then display the menu bar and a grey background and remain unresponsive. I tried downloading a new copy of Lion in Recovery HD but it will not get past about 1/8 of the download bar before freezing and becoming unresponsive. Any ideas?

Any ideas?? I really need to see if this is fixable! Thanks!

Similar Messages

Help Please! Macbook will not boot after MacOffice install

I've never used a mac before until now. I've a 2.2ghz, 2gb ram macbook(late '07, it has an *hitachi HD* which I've had for less than a week and was running fine until I installed mac office 2004 student edition.
During the installation process i was prompted to update macoffice and after a while i couldnt see the microsoft update status bar and i just got to the screen where it said installation complete, I clicked 'finish'and then I waited for 30mins or more where i got a spinning colour wheel, and the fans were spinning a lot and it felt quite warm so I decided to turn it off.
When I booted up again I got a *flashing folder with a question mark* on the white/greyish screen. After resetting the P/VRAM(?) a number of times I eventually got into the desktop. Thinking that microsoft must have corrupted some system files. I decided to do an erase and install but when i tried to do it I got a warning screen with 'install failed'and 'the installer is experiencing errors installing on "macintosh HD" The disk may be damaged. Please try installing on another disk...click restart and try again'.
I then tried to use 'disk utility'using the os x disc. I ran first aid on the macintosh HD. I verified and repaired disk permissions but when i tried running verify/repair disk i get in red 'Invalid b-tree node size, volume check failed..Error:filesystem verify or repair failed.'
The lines for apple care are shut today as well..any light shed on this problem appreciated. Any ideas what i can do...I really hope it isnt hardware failure..but the hard shutdown/restart suggest it may be?
Message was edited by: Anon87
Message was edited by: Anon87
Message was edited by: Anon87

The question mark means that important system files needed for startup are either missing or damaged. The only solution is to boot from your Installer DVD and perform an Archive and Install or an Erase and Install.
How to Perform an Archive and Install
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger) and/or TechTool Pro (4.5.2 for Tiger) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Macbook will not boot after 10.5.2 install

After installing the 10.5.2 update via software update (from 10.5.1) my macbook will no longer boot. I get the Apple logo for about 5 seconds then I get the 'You need to restart your computer' message. I can't get past this point. Any suggestions on how to get my laptop back to life would be appreciated.

Start by:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now shutdown the computer for a couple of minutes and then restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Then download the standalone updater and reinstall 10.5.2. If that doesn't solve your problem then you will have to do an Archive and Install.
How to Perform an Archive and Install
1. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
2. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
3. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
4. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
5. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

Macbook Will Not Boot After Updating Leopard

I just reinstalled Leopard after having some trouble with my partition tables, and everything ran smoothly and worked fine. After the install I let software update update everything including the 10.5.5 update. It prompted me to reboot, and when I did it got to the grey Apple screen and the thing spun for about 30 seconds before it restarted and did it again. This happened a few times and then I booted from a Leopard disk to look at disk permissions and they seem to be fine. Anyone have any idea why this is happening or how I would fix it?
Thanks in advance, hope to get this sorted out quickly, I thought I had finally gotten my computer working fine again when I reinstalled Leopard. :P

At start up, press 'C' to boot directly from a CD/DVD. Or, you can press 'Option' and you should get a list of bootable selections (CD/DVD, external hardrives) that you can boot from - assuming you have something that IS bootable.
I recently had a problem and ended up reinstalling my OS (via TimeMachine). I also confirmed that you can boot from your original OSX install disk. As part of this process I also discovered I could NOT boot directly FROM the AppleCare provided TechTools Deluxe disk. Supposedly you can boot INTO that disk via a restart but that seems kind of silly to me.
However, if you have signed up for AppleCare and go to the Apple Support web site, you can download TechTools Deluxe and it can be made bootable by burning the .dmg file via Apple Disk Utilities. I don't understand Apple logic of not making the provided AppleCare TechTools Deluxe disk bootable.

Macbook will not boot after last 10.5.2 airport update

Installing the latest airport update to 10.5.2 killed my macbook. If I do a opotion+apple key+s, I get the following message
loading system\library\extension.mkext .............error x0000008 or something like that.
Any suggestions on how to fix that? I seen something on the internet about deleting mkext file, but am a little afraid I will make things worse. Is there a way to boot up with this error like a safe mode, or do I have to boot with external USB disk or installlation disk? Any little details would help. I am familiar with Linux and WinXP, but not mac OSX.

This problem has been solved. Booted of USB drive and deleted the file. It started after, although it took awhile.

My Macbook will not let me close out of my iPhoto and it's continuously saying that it's importing pictures when I have nothing plugged in. What should I do?

It is making me very fustrated.

Apple menu - Force Quit - iPhoto. Then I would restart the mac and make sure that iPhoto behaves.

My Macbook will not boot the operating system. It just goes to a blue screen after the apple logo and the spinning wheel goes off. I took the battery out and held the on/off button for five seconds and reset the PRAM. I have the old mac os disk.

My macbook will not boot. It goes to a blue screen after the logo and wheel goes off. I have taken the battery out and held the on/off button for five seconds and reset the PRAM. I have the the original os disk but have not put it in for fear of losing un backed op data.
Thanks
Rich

You won't lose any data unless you erase your hard drive.
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.

Macbook will not boot up after running Software Update

My MacBook will not boot up after running Software Update (Security update + Java?) earlier today. I have only the gray start up screen + Apple logo + gear wheel constantly rotating. I have tried restarts several times and tried to start up from my original system DVD - this makes no difference.
I called Apple support, tried resetting the power and PRAM - still no difference. He had no knowledge of other problems reported; although I note recent post may have same issue.
I cannot get an appointment at my Apple Store before Monday.
Any suggestions?

Still no success. When I hold down the option key when powering up I get the hard disk icon plus arrowhead (only). When clicking the arrowhead it goes to the gray screen + apple logo+ rotating gearwheel.
This happens both with DVD in slot and without DVD. the DVD image is not coming up on screen. When I start up without DVD the hard disk icon appears promptly. When I start with DVD in the DVD is spinning for a short period before the hard disk icon appears. On clicking the arrowhead to hard disk icon the DVD spins again for a while then stops. Apart from the DVD spinning, both situations result in gray screen + apple logo+ rotating gearwheel.

After updating Airport software, Macbook will not boot

I see others have updated with the new Airport software without incident, but not me.
I just ran software update to install the Airport update (hoping it would cure the problem I've had -- and other users as well -- with the connection dropping every 5 minutes with Linksys routers [check the Airport discussion board for much discussion of this]).
After installing, upon restart my Macbook will not boot fully. I get the Apple symbol, then the spinning gear symbol, then a light blue screen and that's it. After a while the fan comes on.
Call it the light blue screen of death.
All was working fine until the update.
I have boot camp and I can boot into Windows.
I have tried removing the battery and resetting the PRAM. No help.
Sigh... Applecare is closed so I cannot call until Friday morning. Anyone have any suggestions of what I can try?
I have my Mac hard disk backed up from a few days ago using Super Duper on a USB drive but I am reluctant to try booting from it as I fear corrupting the drive. Unfortunately I don't have my Mac system CDs with me as I am away from home at the moment.
I just switched to the Mac 6 weeks ago after 3.5 years with a Dell laptop. Never had a single problem like this in all that time. But I still like my Mac.
PD

Well, I spoke too soon. Last night I was able to start up as described above, but this morning when I tried to start it did not even get to the Mac symbol. It just hung at a dark blue screen for several minutes.
Tried restarting with the shift key held down but it would not go into safe mode. Just the dark blue screen.
Resetting PRAM made it startup.
But I'm pretty nervous about this.
So, is there a way in Mac OS X to roll back to the system before the update? In Windows XP this is very simple under System Restore. I have the impression OS X doesn't have this feature and won't until next year with Time Machine.
And I see now I'm not the only user with this problem.
PD

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

It rained in my window last night, on my power strip. My macbook adaptor (charger) and iphone adaptor were both plugged into the strip. The power strip is dead. Iphone is fine. Macbook will not boot up and charger light doesn't go on.

It rained in my window last night, on my power strip. My macbook adaptor (charger) and iphone adaptor were both plugged into the strip. The power strip is dead. Iphone is fine. Macbook will not boot up and charger light doesn't go on. I borrowed another charger and still no luck. What should I do? (Charger wasn't plugged into Macbook until I dried it off.)

Spill Cleaning
And, don't think that just because it was two teaspoons and not a glassful that there is a difference.
Some liquid has just spilled into your Mac. What should you do?
Do
Immediately shut down the computer and unplug the power cord.
Remove the computer's battery (if you can)
Disconnect any peripherals (printers, iPods, scanners, cameras, etc.)
Lay the computer upside down on paper towels to get as much liquid as possible to drip out.
Note what was spilled on your Mac.
Bring the computer into an Apple store or AASP as soon as possible.
Don't
Don't try to turn it back on. Liquids can help electrical current move about the components of your Mac in destructive ways.
Don't shake the computer (this will only spread the liquid around).
Don't use a hair dryer on it (even at a low setting a hair dryer will damage sensitive components).
Do not put in a bag of rice in as much as rice will get into the ports and optical drive and do further damage.

My MAcBook will not boot up. I get A white screen along with the light on the front of the mac with a beeping.

My MacBook will not boot up all I get is a white screen with the light on the front of the mac blinking and a beeping.

Check this Apple support article https://support.apple.com/kb/HT1547

MacBook will not boot after iTunes 10.5.2, iPhoto, and Safari update

Similar Messages

Maybe you are looking for