Macbook wont move past initial wireless setup

I got my macbook yesterday and it started up with the welcome sequence, asked me to select languages and then asked to connect to a wireless setup
I selected my router, put in the password and it said "configuring computer"... I thought it would take a moment, but 3 hours later it STILL read "configuring coumputer"

I would recommend calling 1-800-My-APPLE and have a tech help you out. That will be the fastest way to resolve your problem.

Similar Messages

My macbook wont get past the gray startup page !!

my macbook air wont get past the gray startup page!!
i read about it and i think its because of the HD low space !
so what should i do ?
i tryed to repaire it and it didnt work !!

With an external drive, after it has been setup, partitioned, etc., go to System Preferences and Time Machine, or if TM is showing on your dock, just click on it, and turn time machine on...you can then give it the name of the partition on the external drive where you want to backup. TM will do that in the background and you don't have to think about it.
I have the Mercury Elite Pro drive from OWC, 2 TB, that I partitioned into a backup partition and working partition...so TM backs up regularly and I can use the other partition for either another bootable Mac OS X space or just point applications to that space for file storage.
You can clone the operating system using Carbon Copy Cloner or SuperDuper which are both free downloads. They make a bootable copy of the operating system for you.

My Macbook wont load past the apple screen.

ok so I have a macbook from late 2007 and it's not loading past the apple screen. Yesterday it froze so decided to turn it off and it hasnt started up since. Ive tried safe mode, resetting the NVRAM/PRAM, and then i decided to restart it and press command v and a screen popped up saying.
npvhash=4895
PRE enabled
64 bit mode enable
darwin kernel version 18.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/release_1386
vm_page_bootstrap: 246299 free pages and 15845 wired pages
standard timeslicing quantum is 10000 us
mig_table_max_displ = 73
AppleACPICPU: Processor Id=0 LopicId=0 Enabled
AppleACPICPU: Processor Id=1 LopicId=1 Enabled
calling mpo_policy_init for TMSafetynet
Security policy losded: Safety net for Time Machine (TMSafetyNet)
calling mpo_policy_init for Quarantine
Security policy Loaded: Seatbelt sandbox policy (Sandbox)
Copyright (c) 1982, 1986, 1989, 1991, 1993
     The Regents of the University for Californai. All Rights reserved.
MAC Framework successfully initialized
isong 5242 buffer headers and 4096 cluster 10 buffer headers
IOAPIC: Verdion 0x20 Vectors 64:87
ACPI: System state [so s3 s4 s5] (s3)
PFM64 0xf10000000, 0xf10000000
[ PCI configuration begin ]
PCI configurstion changed (bridge=1 device=1 cardbus=0)
[ PCI configuration end, birdges 4 devices 17 ]
AppleIntellCPUPowerManagement: (built 16:44:45 Jun 7 2011)ninitialization complete
mbinit: done (64 MB memory set
for mbuf pool)
FireWire (OHCI) Lucent ID 5811 built-in now active, GUID 001cb4fffe8bb384; max speed s400.
rooting via boot -uuid from /choosen: 49342205-A733-3921-9F2C-4D88EAA7EB64
Waiting on <dict ID="0"><key><string ID="1">[0Resources</key><string ID= "1">I0ResourceMatch</key><string ID= "2">boot -uuid-media-</string></dict>
com.apple.AppleFSCompressionTypeZlib Kmod start
com.apple.AppleFSCompressionType L\load succeeded
appleIntelCPUPowerManagementClient : ready
Got boot device = IOService:/AppleCPIPlatformExpert/PC1000/AppleACPIPCI/SATA@1F ,2/AppleAHCI/PRT2@2/I0AHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice /
IOBlockStorageDriver/ST980811AS Media/IOGUIDPartitionScheme/Untitled 102
BSD root: disk0s2, major 14, minor 2
[Bluetooth: :CSRHIDTransition] switchToHCIMode (legacy)
[Bluetooth: :CSRHIDTransition] transition complete.
CSRUSBBluetoothHCIController: :setupHardware super returned 0
AppleYukon2: Marvell Yukon Gigabit Adapter 88E8053 Singleport Copper SA
AppleYukon2:RxingSize <= 1024, TxRingSize 256, RX_MAX_LE 1024, TX_MAX_LE 768, ST_MAX_LE 3328
disk0s2: 1/0 error.
     0 [level 3] [ReadUid 0] [Facility com.apple.system.fs] [ErrType 10] [ErrNo 5] [10Type Read] [PbnukNum 50624960] [LblkNum 8] [FSLogMsgID 142858201] [FSLogMsgOrder First]
     0 [level 3] [ReadUid 0] [Facility com.apple.system.fs] [DevNode root_device] [MountPt /] [Path /usr/lib/dyld/ . .namedfork/rsrc] [FSLogMsgID 1462858201] [FSLogMsgOrder Last]
/SourceCache/AppleFSCompression/AppleFSCompression-24.4/Common/commonUtilsKern.c :344: VNOP_GETXATTR com.apple.ResourceFork for /usr/lib/dyld: 5: error
/SourceCache/AppleFSCompression/AppleFSCompression-24.4/Compressors/Type4/Compre ssorType4Imp.c.304: fh_getxattr /usr/lib/dyld: 5: error
/SoundCache/AppleFSCompression/AppleFSCompression-24.4/Common/commonUtils.c:223: supplyChunk: error
decmpfs.c:1149:decmpfs_pagein_compressed: err -1
CODE SIGNING: cs_invalid_page(ox7fff5fc22000): p=1[launchd] clearing CS_VALID
Sleep prevented by SB 1, SS 0, RS 1

reading this, your hdd has unfortunately died. have you backed your system up? if you have it is not as bad as it seems.
you will have to buy a new drive and simply restore to that drive from the backup.

Ok.. macbook wont go past grey screen.

ok so i was normally using my macbook(despite its shutdowns, ive been using it with the shutdown problem for a while now..)
anyway, it all began with my USB ports// my macbook wouldn;t recognize anything.
then i tried playing a DVD.. my macbook asked me what i wanted to do wit the BLANK cd. (um, it wasnt blank!! it was a movie)
so i decided to restart, and viola. screwed!!!
now my macbook is stuck on the start up screen. it wont go beyond the apple+scrolling sign. thats all it stays at. so i put in my installation CD 1, and restarted it with the C button pressed.. ran disk utility and it shows there is nothing wrong ( verified and no repair needed to disk)
i removed the installation CD and tried restarting. nothing. it stays on the start up screen...
help anybody? week 20 macbook.. going to call apple on friday, coz i get back to town on thursday night. someone tell me wat to do. plz..
thx

Okay, since booting to safe mode didn't seem to work try booting to the install disk one.
To do this put the disk in the computer when it is turned on. Next shut the computer down (hold down the power key until it turns off). Then turn the computer on and hold down C key until you are asked to select your main language. (I am going to assume English.) After selecting the language press the arrow. The installer will load, don't proceed with the installer. Instead wait for the top menu bar to appear. Select "Utility," then Disk utility. In disk utility select the Mac HD. Then make sure that the First Aid tab is selected. Press the "verify disk" if there are any errors click "repair disk". If the errors are not repaired the first time around try repairing once more. Once it is repaired double check by clicking verify disk.
Here is an article with some possible error messages
http://docs.info.apple.com/article.html?artnum=302672
To get out of the install disk quit disk utilty then go to installer by the blue apple, go to the Installer Menu and then quit installer and then restart.
Doing the above will in the very least save you some time on the phone with Apple. If you can't repair the disk with disk utility write down any errors and let Apple know.
I hope this helps.
p.s. the steps in the article in my previous steps do also apply to 10.4

2010 MacBook wont boot past grey screen, even after a new hard drive and install CD.

Hey guys, I received a 2010 Macbook last year as a gift (no warranty). It worked fine untill a few days ago. It wouldn't boot past the grey apple logo. I took it in to an Apple store and they said it was a bad HDD. Since I didn't have much stored on it, and I have everything backed up to my desktop, I got a new, larger capacity HDD and replaced it with no issues. I started the Macbook with the OSX Leopard install CD, but it didn't identify the HDD, and now it won't boot past the grey screen.
Any ideas? Is it the motherboard?
Thanks a lot!

House3917 wrote:
I started the Macbook with the OSX Leopard install CD...
Leopard is done for, call Apple via phone and order the 10.6.3 white retail disks and use those.
Use these install instrcutions for best operation and performance.
How to erase and install Snow Leopard 10.6

Macbook wont get past second screen (blue)when turned on

just recently, my macbook (13 in 2008)started acting wrong for no apparent reason.when i turn it on it does the chime and the apple screen then goes to a blue screen and gets stuck there.if i start in safe mode, it doesn't even get past the apple screen. i've also tried to reset the pram, but no luck.

did you try _*resetting the System Management Controller SMC*_ ?
if still no joy, try booting from the install DVD, launch disk utility and run a +repair disk+ session. if DU reports problems, repeat until no more errors appear. if DU insists the disk can't be repaired, you may need to get DiskWarrior or [_*TechTool Pro*|http://www.micromat.com/index.php?option=comcontent&task=view&id=202&Itemid=107].
JGG

Macbook wont go past grey screen with spinning cog below...HELP!

PLEASE, PLEASE....could someone advise urgently, was using machine ok, left it for a few mins & it went to sleep...then I couldn't log back in. Restarted and now can't get past this grey screen....have tried all recommendations...tried re install and says it can't. Tried the fsck...it say's "volume check failed". Tried the disk check...it said there was no problem. I am in Spain (Palma) and about to set off acrosss the Atlanntic to S.Maarten...my warranty expires in April and I am unlikely to be anywhere with a mac dealer or authorised service place in the next 6 months...my life is on this machine!! PLEASE HELP????

What happens if you boot from your system install disk and run Disk Utility? Does the utility see the drive and can you verify/repair the drive?
-Bmer
Mac Owners Support Group - Join us @ MacOSG.com
  Mac611 Mobile Mac Support - about.Mac611.com
   iTunes:MacOSG Podcast | YouTube.MacOSG.com
                   An Apple User Group 
Have an iPhone or iPod touch? Enter Mac611.com in Safari on it for 'mobile Mac support.'

My hp stream wont move past cursor on screen

Help, my hp stream is stuck on black screen with a cursor. How can I reset?

Hi @sbpope ,
Thank you for visiting the HP Support Forums and Welcome. I have read about your HP Stream Notebook and not getting past HP Logo on startup. Try performing a hard reset.
When performing a hard reset please note remove any and all USB devices. Disconnect all non-essential devices.
You can do a system restore. System restore will help if something automatically updated and did not go well on the Notebook.
Hope this helps you.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Display hard to close and wont get past initial boot screen - turns off

I didn't drop it and if someone else did, they won't fess up. It doesn't look bent anywhere.
I turn it on, it has grey boot up screen with apple and rotating timer thingy. The hard drive is noisy like it is in a constant read mode and then it just turns off.
I would suspect the HD is shot, but why is the lid hard to close now? Any thoughts greatly appreciated.

Bring it to an Apple store or authorized Apple repair center.

HP Color LaserJet Pro MFP M177fw makes horrible noise and will not move past initializing

Makes horrible noise and will not move past initializing.

Hi @HealthITLadyRed,
I read your post and see that the printer is making noise and is stuck initializing. I would really like to be able to help you resolve this issue.
I have provided some steps to try to see if we can resolve this issue.
Check and remove any packaging material inside the printer and toner.
Disconnect the USB/Network/FAX and power the printer on Standalone.
Do a hard reset to see if that will resolve the issue.
Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
This ensures the printer is receiving full power and may help this situation.
If the issue persists, perform a power drain by disconnecting the power cord from the back of the printer and keeping the power button pressed for 30 seconds and in case of a power switch keep the switch in ON position for 30 seconds before reconnecting the power chord.
Update the printer's firmware by a USB connection. Software and Drivers.
Select Option 2 and wait for the page to load and then select the link for firmware. This resolved the previous posters issue.
I can send a private message with another step to try.
In the forum beside your handle name just click on the envelope to view it.
How is the printer connected? (USB/Ethernet/Wireless)
What happened prior to this issue? (paper jam, changed toner) Any feedback would be appreciated.
Is this a new printer?
If you appreciate my efforts, please click the Thumbs up button below.
If there is anything else I can help you with, just let me know. Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

My Mac mini turns on but doesn't move past the grey screen..... HELP??

Hi,
I have had my mac mini for 3 months and i went to turn it on today and it wont move past the grey screen with the apple logo and the swirling icon underneath. It had started to drop internet signal and also reacting slow and now this has happened. I have only had it three months from new and i dont know what to do. I have done a safe reboot etc and nothing has worked !! HELP!!

Intermittent problems are by far the most difficult to identify and correct. You can run a test one time and it passes with flying colors and the next time it fails. Apple Hardware Test and Disk Utility are definitely the not the most rigerous tests available and are not nearly as thorough as the tests available to the Genius Desk personel.

Pronblems my macbook wont pass the apple logo

i have a macbook with the snowleopard osx 10.6.4 and my macbook wont boot past the apple logo!
i've tried pratically everything
cmdoption+pr
snowleopard dvd+c after the booting sound
cmd+v
taking of battery
taking of adpter
press the shift button after hearing the boot sound
evry single thing but it wont just past that hateful apple logo!!
the last operation i did was to cancel from my avast antivirus for mac (log system file) that was "according to the antivirus" a decompression bomb so i eliminated it directly from the source in finder library and after that pages won't just open and so i tried rebooting the system hoping it'll solve the problem but then it just keeps remaining stuck at the apple logo!!
it just stays there for about 2 days now coz i tried waiting thinking it was only slow!!
i can't take it to repair without an applecare it'll just be a **** of money!
can anyonepls help me??
i'm despirate!!

Boot with the Apple Hardware Test disc and run the extended tests.

Macbook wont login

macbook wont go past login screen it will start to login but go back to login screen

Wrong forums. These are for Snow Leopard, not Leopard.

My macbook pro wont get past the grey screen at startup. Help!!

After doing a run of the mill software update on my macbook pro (running snow leopard) it froze during the "moving items into place" stage. I forced a shut down and now it wont get past the grey screen with apple logo and spinning wheel. I have tried booting from the original DVD but it still freezes. When I boot it in verbose mode it seems to stop at "jnl: unknown-dev: update_fs_block: error reading fs block # 3597880! (ret 5)", the Apple AHCD Disk Queue manager :: set power state is timing out and there is a disk I/O error. I have tried to reset the power manager (not sure if it worked or not) and I have also tried clearing the PRAM (again, not sure of that worked). When I try to look at the hard drive using target mode on my imac the hard drive doesn't come up but the DVD does. I'm concerned that my hard drive is fried. Any suggestions?

It would help to state in your post which remedies you tried that didn't work.
Start here > OS X Lion: If you see a gray screen at startup
If nothing there helped, try Starting up in Safe Mode
Safe Mode deletes some system caches that may help.
A Safe Mode boot takes longer than a normal boot so be patient. Once you are in Safe Mode, click Restart from the Apple menu.
If a Safe Mode boot didn't work, since your Mac has OS X v10.7 installed, restart your Mac while holding down the Command + R keys so you can access OS X Recovery built in utilities. The startup disk may need repairing.
Tip: Hold down the Eject key while starting up your Mac to eject a disc.

On the initial set up for apple tv it just sits there trying to set the date and time . it is a wireless setup and the ipaddress and router address is correct . I can't get by this screen

On the initial set up for apple tv it just sits there trying to set the date and time . it is a wireless setup and the ipaddress and router address is correct . I can't get by this screen. The setting is on automatic and I have picked a city in my time zone yet it still tries to set a time and date but fails.
thanks

Make sure router is up to date. Try ethernet to rule out any wifi issues. Reboot ATV and router.

Macbook wont move past initial wireless setup

Similar Messages

Maybe you are looking for