Macbook wont powerup, beeps repeatedly when power button is pressed and you need to hold the power button down to shut the beeping off. any thoughts?
Have a 13" macbook. wont power up. upon hitting power button, the computer sounds 3 long beeps constantly until you hold the power button down for 5-10 seconds. any thoughts out there?
Thanks guys, i just read a few articles regarding this. i pulled all the ram and tried swapping and reseating ram. it appears both chipsets are fine but one ram slot is bad. computer will boot with either chipset installed in the one good slot but neither chipset will boot in the other slot. bummer....
Similar Messages
-
My iPhone 6 wont come on when home button is pressed and screen pixels out and fades. Any one have fix or same problem?
When I press the home page the screen activates but stays black. I have to press the side button to turn if off then may have to repeat several times to get my phone to come on. Sometimes while using the phone the screen will become pixelly and start to fade away leaving a white screen with vertical line on it. I have to use the close button to make it go away.If one of the two major buttons of your phone is broken, it is unfair to expect normal operation to be available. The first resolution to any problem involves a usable Home button, as does the second option for resolving any problem. Get your Home button fixed.
-
I have usb driver in may macbook pro 15 retina. When I installed windows 7 and try to download windows support into a CD, boot camp always said it couldn't find my usb driver. My mac version is 10.8.3
Welcome to the Apple Support Communities
Install the Windows support software from the USB drive. Note that Boot Camp Assistant, in OS X 10.8.3, doesn't support the option to burn the Windows support software into a disc.
Instead, you can try a different thing. Start in Windows and download the Windows support software in it > http://support.apple.com/kb/DL1638 Then, decompress the file and run the Boot Camp drivers installer.
If you can't access to the Internet in Windows, start in OS X and download the Windows support software from the same link. Decompress the file, right-click the folder which will show up after decompressing the file and select "Burn". Finally, start in Windows and install the Boot Camp drivers -
when I connect an external hard drive to macbook pro it is very slow to appear on the desktop and Finder window, sometimes 20 mins or more, even with auto backup switched off . any clues?
Hi robfromkinglake west,
Try and isolate the issue. Check if it's only with this drive.
Check the drive with Disk Utility
Using Disk Utility to verify or repair disks
http://support.apple.com/kb/ht1782
I've never seen a drive take 20 minutes to mount.
Nubz -
Trying to download iTunes 10.7 in Windows 7 64-bit. When I click the download now button, it immediately goes to the "Thank you for downloading" screen, but the file has not downloaded. Popups unblocked. Any thoughts? Thanks!
I'd first try downloading an installer from the Apple website using a different web browser:
http://www.apple.com/quicktime/download/
If you use Firefox instead of IE for the download (or vice versa), do you get a working installer? -
When I using the mouse to select portion of the diagram or the panel, or when I moving objects- I found that in all the vi's that I compiled from former versions of labview- there is a delay of close to a second to the actual selection or movement of the item. This happens in 2 machines out of 5 that I tested it, and it happened both in windows 2000 and in windows 98. any suggestions?
Sometimes a video driver issue. Update your video driver.
Or turn down the video driver hardware acceleration. Right-click an
empty area of the desktop, choose the Settings tab, choose the Advanced
button.
The location of this differs in different versions of Windows.
Win2000: go to Troubleshooting, and turn down the slider for hardware
acceleration.
Win98: I think it's on another tab.
Mark
ilan wrote:
>
> Delayed response of when moving objects in diagram and panel, happend
> in LV 6, only for vi's compiled from previous versions. any
> suggestions?
>
> When I using the mouse to select portion of the diagram or the panel,
> or when I moving objects- I found that in all the vi's that I compiled
> from former versions of labview- there is a delay
of close to a second
> to the actual selection or movement of the item. This happens in 2
> machines out of 5 that I tested it, and it happened both in windows
> 2000 and in windows 98. any suggestions? -
Hello, I am trying to use a photo,that I've opened up in pages on a blank landscape, taken from my camera roll and use it as album cover art. All the custom text's will not paste when I copy. Pic and texts are saved as a PDF, how can I paste the doc ?
Hello, I am trying to use a photo,that I've opened up in pages on a blank landscape, taken from my camera roll and use it as album cover art. All the custom text's will not paste when I copy. Pic and texts are saved as a PDF, how can I paste the doc ?
-
My ipod touch stopped working. The screen is black with a small white circle/wheel with ridges/teeth in the middle of the screen. No matter what button is pressed and/or held nothing happenes. Can anyone assist me?
Try the remaining items of:
iOS: Not responding or does not turn on
If not successful and you can't turn the iPod fully off, let the battery fully drain. After charging for at least and hour try again.
- If still problem time for an appointment at the Genius Bar of an Apple store. -
my iphone says 'iphone is disabled connect to itunes' and when i do connect it, it says 'iphone could not connect to itunes because it is locked with a password and you need to unlock it but it doesnt let me as it is diabled???????
hi, may i know how to restore and put it on recovery mode??
as I faced the same problem as you now...
Thanks -
Does anyone know why a web page would suddenly pop up telling me I have a computer virus and need to call them? When I've called they said they needed access to my computer in order to fix the problem - which I didn't do. Is this legit? An Ad?
That is not legit, it is a scam to gain access to your computer and information.
You can protect against pop-up adware with the AdwareMedic tool Thomas Reed has http://www.thesafemac.com Tom is a major contributor on these communities and great security guy. -
When some one calls the caller ID shows the name twice as we'll as when I receive texts it shows up twice. I'm sure it's a simple setting issue. Any thoughts ???
have the same issue on my 9630 after upgrading to 624 version. It momentarily shows the previously callers information before showing the new caller's info.
-
Hello,
I´ve a Problem with Muse.
Why are on the first web page buttons are shaped and following pages don´t? All Pages are based on the same Masterpage.
Any ideas?
StefanI just republished the site, and it looks fine, energievollfit | über
could you please try to republish the site again, and let me know . -
''Duplicate post, continue here - [https://support.mozilla.com/en-US/questions/828024]''
when we using overflow-x and overflow-y in tbody its not working properly. In the previous version i.e. 3.7.1 its working fine the same coding....Please help me.See:
*https://developer.mozilla.org/en/Firefox_4_for_developers#Miscellaneous_DOM_changes
*http://www.cssplay.co.uk/menu/tablescroll.html
A good place to ask questions and advice about web development is at the mozillaZine Web Development/Standards Evangelism forum.<br />
The helpers at that forum are more knowledgeable about web development issues.<br />
You need to register at the mozillaZine forum site in order to post at that forum.<br />
See http://forums.mozillazine.org/viewforum.php?f=25 -
I can't find the deactivate button. I know you need to go to Help > deactivate. But where is this help? On Adobe or on my computer?
Open whatever application you wish to deactivate and from the top toolbar choose Help -> Deactivate. If this is for a Creative Suite then just open any one of the applications that are in it and deactivate thru that - it will deactivate the entire suite.
-
I can't reach recovery system when I reboot- I press 'command' and 'r' quickly, but nothing happens, the progress bar begins to load... Any thoughts? It gets about halfway through loading and then stops, no mouse, no nothing. I think I'll be able to move past it if I can reach the Recovery options.
Thanks!If you are really sure that it's impossible to click in Recovery mode, then something is wrong with the machine.
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed.
Maybe you are looking for
-
How do I pull together multiple PDFs into one Preview Document?
Folow up --- I learned from the video how to create one Preview document from mulple PDFs, but I need to know how to position pdf files in a main PDF Preview presentation document. I need a lot more control over where a pdf is set in the final PDF d
-
I have a Mac OS X 10.6 When I try to send an attachment with email it won't send - keeps saying 'fail'. Please could someone help? Thank you.
-
As a learning resource, I want to convert the Page.Resources and Grid.DataContext to a class structure. Unfortunately I have no idea what route to take. I have looked at the MSDN documentation and found 3 possible ways I could approach this, although
-
From where to start android programming ?
the question pretty much explains it. i have almost completed java programming. i have completed half of java essential classes from oracle java tutorials but what i mean is which ide should i download and from where should i learn it. for java progr
-
Explain Plan not working with 919, was working with 804
Hi, Explain Plan (F6) was working cprrectly with Raptor 804 and is not working any more on 919. This is the same query exactly (select * from mytable). The server is 9.2.0.5.0. The result with 919 is "Invalid Column Name". Regards Eric