MacKeeper for new imac is a program from Apple and ok?
Ich habe neu einen IMAC, da kommt ein Reinigungsprogramm MacKeeper, ist das amtlich und in Ordnung und bringt es was?
MacKeeper ist nicht von Apple, es gemacht wird und von Menschen, die Geld ohne Angabe nützliches Produkt machen wollen gefördert.
Niemand mit Mac Erfahrung empfehlen die Nutzung dieser Anwendung. Diese usless Software verlangsamt den Mac herunter und tut nichts, dass das Mac-Betriebssystem wird kostenlos tun. Installieren Sie es nicht.
Similar Messages
-
How much RAM should I install for new iMAC ?
Hi,
How much RAM should I install for new iMAC* running Logic Studio? It comes with 4 GB - is that enough? (can you run in 64 bit mode..)
*(The 21.5" 3.06GHz Intel Core 2 Duo)
Also, I was planning to get the stock 1 TB Hard Drive & save projects to an external drive.
Does that sound reasonable?
Any other recommendations?
Thanks,
Wm HeartUnless you plan on running huge projects with enormous sampled instruments, 4 GB will do (very) fine. And your disk plan is sound. Choose an external Firewire drive, rather than USB. FW is easier on the CPU and can handle more tracks than USB.
What you should get, instead of more memory, is a (24 bit) external audio interface, if you want to do serious recording and playback.
What type of audio interface you'ld need, depends on what you want to do with it and of course your budget. From decent to brilliant costs from roughly 100 to several 1,000's of europounddollars. Avoid the 16 bit ones, they're worse than the inbuilt audio chip of your iMac. You can recognize 16 bit Audio Interfaces (in webshops) by their prize (often under 100€£$) and the lack of mention of their bitrate.
HTH
Regards, Erik. -
I have an iPad1 and will buy a new one. Is there any exchange program from Apple? Thanks
I have an iPad1 and will buy a new one. Is there any exchange program from Apple? Thanks
No there isn't. You could try to find if a store in your country does have one, but you are likely to get a higher value for your iPad by selling it privately e.g. to family, a friend etc.
-
New iMac is stuck on grey apple screen after restart from Migration Assistant
New iMac is stuck on grey apple screen after startup. It is a 3.4GHz Quad-core Intel Core i5 running OS 10.9.4. The problem occurred after a migration from my older 2009 iMac which is running Snow Leopard 10.6.6. When the restart occurred from Migration Assistant, the new computer will not boot up to the login screen. Disk utility did not solve problem. Followed instructions for a soft reinstall of Mavericks but that also did not solve problem. Any suggestions?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
hey sur. my name anas and am from morocco i've just got a new iMac 2011 with OSX 10.7 and i want to downgrade to 10.6 please could you help sur to solve this it
anas guellaf wrote:
it still make 3 bips before starting the IMAC.
That is another problem not related to the Mac OS X version you are trying to use.
Three beeps at startup means you have a bad ram module in the computer. Did you install the ram or did it come from another owner this way? The first problem you need to solve is the bad ram.
When the iMac starts, go to the apple left side of the menu bar, About This Mac, More Info, System Report, Hardware, Memory and see what the report is on the memory...does the iMac report all memory modules that have been installed as OK or does it show bad memory? If there is not any information, you then need to remove the memory modules and restart one at a time to see which is bad.
On the bottom of the screen there should be a small door that you can remove with a small screw driver. You need to lay the iMac flat, disconnect the power cord, remove that small door and remove the memory modules. You can then put two in (if it has four) and see if it starts without the beeps. Do that with each module so you find out which is bad. Once you know the bad memory, you can buy a new module, just like the ones installed, so the iMac starts without the beeps.
Next, you cannot use a DVD for another computer for your iMac unless it is from one that is identical to yours. So, you need to talk to Apple and have them send the DVD for your particular iMac. -
How to make a boot disk for new iMac?
I just purchased a new iMac equipped with a bare bones 1TB SATA hard drive. I want to replace that disk with a 1TB SSD from Crucial (less than 1/2 of the cost of purchasing the iMac with the SSD). I have a Time machine backup of the iMac on a Time Machine/Airport device; how do I make a boot disk that can get the OS up and running, and able to restore the backup from the Time Machine?
Thanks,
Tony Darst
Baton Rouge, LAtdarst wrote:
I had not given the warranty issue any prior thought; thanks for pointing that out. Is there a way around the warranty issue; such as a "factory authorized" way to install it, that is feasible?
Thanks for the quick response...
TD
You can take it an AASP to have the install done however you probably would be better off returning the machine (assuming it was bought directly from Apple and is less than 14 days old) and buy the configuration you want. Even if an AASP does install the SSD there is no guarantee Apple will honor the warranty, it's 100% at their discretion. -
What is the best and reasonably priced external cd/dvd optical drive for an Imac 21.5 inches from late 2009?
A lot of people have a Mac where the superdrive has been taken out to be replaced with a harddisk. Try to find a friend who has done that, give him a beer and take the superdrive, then buy a superdrive container from OWC or another for afew dollars and put it in there. This slimdrive container has a USB connector. There you go.
-
Best USB CD/DVD 'Superdrive' drive for new iMac
I've been reading several posts about external (USB?) optical DVD +/- burner/reader drives for the latest desktop iMacs, and several comments have been about various third party ones being superior to the external Apple one that's also available (i.e. that Apple drives often give trouble and are less reliable).
Having seen the likes of LaCie, Western Digital and Seagate mentioned, I'd appreciate comments/recommendations before I go ahead and buy a new iMac - along with an external Apple? or third party? drive.The new iMacs use USB 3.0 speeds, now.
I would look for an optical drive that uses the new USB 3 connections.
This will be a very fast drive.
If you can't find an optical drive with USB 3.0, then look for a drive that uses FireWire 400/800 and use an Apple FireWire to Thunderbolt adapter to connect the drive.
FireWire 800 optical drives are pretty fast at up to 85Mbps transfer speeds.
Here is one such drive.
http://eshop.macsales.com/item/OWC/MRF82SD24S/
And the Apple adapter.
http://store.apple.com/us/product/MD464ZM/A/apple-thunderbolt-to-firewire-adapte r?fnode=51
Good Luck! -
There were some updates on my Apps. I updated them on my iTunes but my iPad did not get the same downloads/updates thru iCloud. Does the iCloud only works for "New" Apps or Books downloaded from the store but not the "Updates"?
Purchased music does not count against your iCloud storage and you cannot get rid of them in the purchased tab.
What is backed up
You get unlimited free storage for:
Purchased music, movies, TV shows, apps, and books
Notes: Backup of purchased music is not available in all countries. Backups of purchased movies and TV shows are U.S. only. Previous purchases may not be restored if they are no longer in the iTunes Store, App Store, or iBookstore.
Some previously purchased movies may not be available in iTunes in the Cloud. These movies will indicate that they are not available in iTunes in the Cloud on their product details page in the iTunes Store. Previous purchases may be unavailable if they have been refunded or are no longer available in the iTunes Store, App Store, or iBookstore.
Look here for help on managing iCloud storage.
http://support.apple.com/kb/HT4847 -
I have a brand new iphone 4s unlocked version from singapore and I am experiencing constant network fluctuations on my iphone , no service, call failed, invalid sim, sim failure, bars fluctuating from 5 - 3 - 2 - 1, no signal/bars searching etc... Ifeel miserable after trying out all the options changed multiple sims, tried multiple carriers, restored the phone back and have set-up as new device but the problem does not get solved... its is so frustrating that after investing on a world's most expensive phone you cannot enjoy the calling features which the phone offers which is the main thing you own the phone for.. Rest of the things are working.. The funniest part I am not able to make calls or receive calls but can access the internet.. I have tried every possible thing and really very frustrated with this iphone of mine...I hope the problem gets solved.. would anyone have any solutions to this problem.. Does it mean one should never update software as I hear that after updating to IOS.5.1 the problem has started coming and same has been with there.... Apple says its a hardware failure which is very difficult to digest as sometimes I get 5 bars and able to make and receive calls but 95% of the time I am unable to. If anyone has any solution I will be very happy if he or share can share the same. Many thanks. its so disgusting to experience this on top of this apple does not support global warranty for the phone as you need to go to the country from where you bought the phone for replacement.. Truly sad state of affairs.. very very very dissappointing.
Have a look at this it might help
http://support.apple.com/kb/TS4148 -
I just got my MacBook Pro a month ago. However I am realizing I need more hard drive space due to aps and programs. I use am external but am concerned about the space. Is there a way to upgrade my hard drive from apple and keep my warranty valid?
That would depend on whether your model actually has a hard drive. If you have the new 2013 Retina model, then you have a fixed storage device built-in that cannot be modified after purchase.
-
I got this new Ipad. After a month my charger broke. So what I did is got a new charger that is not from Apple company it was from a different company. After 3 week it doesn't work anymore. What do I do. HELP ME PLEASE!!!!!!!!!!!
Not normal. Take it (iPad, cable & charger) to an Apple Store for evaluation.
Make a Genius Bar Reservation
http://www.apple.com/retail/geniusbar/
Cheers, Tom -
I bought iphone 5s device only from apple and used my o2 sim for sometime, now I want to use 3 sim, can I replace the sim directly or anything Apple has to do on my device?
Yes, I bought iPhone 5s from Apple.com/uk and paid full price(no contracts, not pay as you go). From your reply I take it that it wont be locked on O2 even though my first sim used on the device was on O2. This is helpful to know, I will change it with a new sim from 3 and see (definitely will switch off while doing so). Thanks for your suggestion. After changing the sim probably in a few days time, I will confirm to you again.
-
Firefox upon opening an image in a new tab, centers the image from top and bottom and surrounds the image with a grey frame. Just started having the problem today, searched Google to no avail.
Oh wow, looks like a new feature.
The "page" links in a stylesheet with the address "resource://gre/res/TopLevelImageDocument.css". If you remove that reference, then the image displays in the old style.
'''''Edit: Please skip the rest of this post and check out the next one.'''''
There might be a more elegant solution than that, but you could use a bookmarklet to strip out that link when you want to view the page in its old style. A bookmarklet is a snippet of JavaScript you save on the Bookmarks toolbar for quick access.
First, copy the following code to the clipboard (it's all one long line):
<br>javascript:var ssheet=document.querySelector('link[href="resource://gre/res/TopLevelImageDocument.css"]'); if(ssheet)ssheet.parentNode.removeChild(ssheet); void 0;
Next, if you are not displaying the Bookmarks Toolbar, use View > Toolbars > Bookmarks Toolbar to display it. (If you aren't using the classic Menu bar, press Alt+v to call up the old View menu. Right-clicking the gray area just below the page address also allows you to display the Bookmarks Toolbar.)
Right-click on the Bookmarks Toolbar (or Mac equivalent of right-click!) and choose New Bookmark.
Paste the code into the Location box (the second box).
Then type a useful name in the Name box (e.g., Oldstyle Picture) and click Add.
Now, when you want to tweak the image display, click the button to run the script.
Manual clicking is a hassle, so it might make sense to look into other solutions. (Greasemonkey didn't seem to work; I think it might not run on .jpg files.) -
Hi, is there a support for development ? I have a idear for a docking station. But i want to know some more details about the licence from apple and so on. Is there a special call center or can i call the normal support for my country ???
For liscensing of iOS related hardware? You'd need to contact the Made For iPod Program.
<http://developer.apple.com/ipod/>
Their contact address is <[email protected]>
Maybe you are looking for
-
How to download the SAP client into text file
Hi, I want to download a SAP client to a text file for backup and then upload it again for restoration when needed. Can this be done?
-
Hi here is my progrom : step1 i define status in Sql*plus define entery_status = ' ' This is my part of progrom select ppf.full_name, pha.segment1 | | '-' | | pla.line_num po_nbr, pv.vendor_name, plt.line_type, msi.segment1, trunc(pha.creation_date)
-
Can I use third-party library in the J2ME wireless toolkit? and How? I have trouble using MathFP library provided by http://home.rochester.rr.com/ohommes/MathFP/ with the J2ME wireless toolkit(1.04, 2.1 and 2.2). If I can not use third-party library
-
Mac OSX 10.6.8 Kernel Panic Error
I have a mac with Intel core 2 duo and 4 gb ram. It also has a 500 gb hard drive. When I try restarting the computer, once in about 4 restarts, I get the kernel panic grey screen that says I have to use the power button to shut off the computer. I lo
-
File type problem with email attachments
Hi, I'm using SO_DOCUMENT_SEND_API1 to send email with an attachment. This attachment is a random file uploaded by the user on an ITS web site and sent to my FM. It is all working fine as long as I tell SO_DOCUMENT_SEND_API1 that the doc_type is 'PDF