MacPro eSata Port/Card doesn't work with new Hard Disk

I just bought 4 x 3TB Hard Disc http://tinyurl.com/d2rglvn (specs of disc)
Which I put in Macally Enclosures to work on my Barracuda internal Hard Drive externally http://tinyurl.com/clg8yjo
I already have like 5 x 1,5 TB that works perfectly well with eSata connections (with exact same enclosures)
**My problem is that my 4 new Hard Discs works really fine with my Mac Pro but only with the USB connections but won't work with the eSata Connection. I tried it on a MacBook Pro with an ATA to eSata adaptor and it works perfectly fine (So my discs are not the problem) **
I am working on a Mac Pro (bought in 2007) - Mac OSX 10,6,8 and this is (I think) the card where I put the eSata :
PCI Card :
pci1095,3132:
Type:    Other Mass Storage Controller
Driver Installed:    Yes
MSI:    No
Bus:    PCI
Slot:    Slot-2
Vendor ID:    0x1095
Device ID:    0x3132
Subsystem Vendor ID:    0x1095
Subsystem ID:    0x3132
Revision ID:    0x0001
Link Width:    x1
Link Speed:    2.5 GT/s
I am kind of new using Mac and its support so what want to know is :
Do I need to update my PCI Card ? If yes how can I do that ?
If not, what can I do to make my disc work ?
My disks are eSata III (6GB/s) is it compatible with my Mac Pro ?
Thank you Very Much for your time

Difference between the disk that works in eSata and those that doesnt is this....
Works : ** 1.5TB 7200 RPM 32MB Cache SATA 3.0Gb/s 3.5"
Doesn't Work : **3TB, SATA III (6Gb/s), 3.5", 7200RPM, 64MB
it is probably the problem but i don't know what to do to fix it !

Similar Messages

Ethernet card doesn't work with new arch install?

Hi guys,
so this is kinda my first post, not that I'm new to arch i just never had an issue i couldn't figure out on my own... But i love arch i have been using it for about a year now and have had no serious problems except for this. I have had arch running on an older dell vostro 200 desktop before i reinstalled with a vary similar issue except that the fix i came up with doesn't work anymore. I will tell you about the first issue first because i ALMOST posted on here about it originally but i figured out a way to make it work even though it was a hassle.
After cold/rebooting my computer the network card doesn't work at all. lspci reported that the kernel module e1000e was the correct one (i have verified this) and that the kernel has loaded it, i verified that with dmesg but still it wouldn't work. After much much anguish and hairpulling, I realized that it had to have something to do with the module so i tried forcing it to reload with rmmod e1000e and modprobe e1000e and it still wouldn't work until i physically unpluged the ethernet cord and pluged it back in until the light on the NIC turned on. After that everything works as normal i could even unplug and plug it back in with no problems. So eventually i wrote a script that did this for me (except for the uplugging and plugging part) and i used that when i cold/rebooted.
But now i have the exact same issue after reinstalling arch to the T except for the fact that the (crazy) fix i came up with doesn't work now. I used my "fix" after booting from the arch cd and it worked just like it always has. And now after rebooting into my fresh system the fix doesn't work anymore. So now i'm back where i was to begin with but i have no idea what to try next. I didn't do anything particularly different during installation except i added a udev rule for the e1000e module just to see if somehow that would fix the problem... it didnt and i have since deleted that (to see if it was the problem). The only other thing that is different is the root and home are now btrfs partitions instead of ext4.
I have booted several other live cds and dvds (diferent distros) including arch derivatives such as manjaro and they all worked just fine, using the same kernel module (e1000e). I'm not sure what that could mean but i know that it means there is a fix for this some way or another. I am going to hook up a wifi adapter and connect that computer to the internet to put some more information up if it's needed (asked for) but for now lspci -vnn | grep -i -A 10 net reports
00:19.0 Ethernet controller [0200]: Intel Corporation 82562V-2 10/100 Network Connection [8086:10c0] (rev 02)
Subsystem: Dell Device 0238
Flags: bus master, fast devsel, latency 0, IRQ 42
Memory at fdfc0000 (32-bit non-prefetchable) [size=128k]
Memory at fdfff000 (32-bit non-prefetchable) [size=4k]
I/0 ports at ff00 [size=32]
Capabilities: [c8] Power Management version 2
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [e0] Vendor Specific Information: Len=06 <?>
Kernel driver in use: e1000e
Kernel modules: e1000e
ip a reports:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
3: enp0s25: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 00:1d:09:8c:36:f6 brd ff:ff:ff:ff:ff:ff
4: wlp0s29f7u3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether 64:66:b3:16:92:10 brd ff:ff:ff:ff:ff:ff
inet 172.16.1.55/16 brd 172.16.255.255 scope global wlp0s29f7u3
valid_lft forever preferred_lft forever
inet6 fe80::6666:b3ff:fe16:9210/64 scope link
valid_lft forever preferred_lft forever
lsmod | grep e1000e
e1000e 215644 0
ptp 17692 1 e1000e
any help on what to do next would be greatly appreciated.
Last edited by mvheart/dev/null (2014-08-18 04:02:12)

Sorry I was thinking that it was say "state up" after that, I was looking in the wrong place... It's been a long time since I was playing around with this. So it is as i thought it was before?
[aaron@arch-box Arch-Linux]$ sudo systemctl start [email protected]
[sudo] password for aaron:
Job for [email protected] failed. See 'systemctl status [email protected]' and 'journalctl -xn' for details.
[aaron@arch-box Arch-Linux]$ systemctl status -l [email protected]
● [email protected] - dhcpcd on enp0s25
Loaded: loaded (/usr/lib/systemd/system/[email protected]; disabled)
Active: failed (Result: exit-code) since Mon 2014-08-18 11:20:29 EDT; 4min 11s ago
Process: 17650 ExecStart=/usr/bin/dhcpcd -q -w %I (code=exited, status=1/FAILURE)
Aug 18 11:19:59 arch-box dhcpcd[17650]: version 6.4.3 starting
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: adding address fe80::ae3:ee04:7099:77c5
Aug 18 11:19:59 arch-box systemd[1]: Starting dhcpcd on enp0s25...
Aug 18 11:19:59 arch-box dhcpcd[17650]: enp0s25: waiting for carrier
Aug 18 11:20:29 arch-box systemd[1]: [email protected]: control process exited, code=exited status=1
Aug 18 11:20:29 arch-box systemd[1]: Failed to start dhcpcd on enp0s25.
Aug 18 11:20:29 arch-box systemd[1]: Unit [email protected] entered failed state.
Last edited by mvheart/dev/null (2014-08-18 15:50:10)

SessionManager doesn't work with new xerceimpl.jar?

Hi,
Does anybody know the solution to the problem below?
The toplink sessionmanager, which loads sessions.xml for database session pooling, doesn't work with new xerce parser(xerceimpl.jar). It is tieing to old xerces.jar parser, which has been upgraded to have more functions.
Thank you in advance.
Praveen

Hi Raanan,
It works with old xerces.jar. But in-order to get new functions from new xerces jars from apache, I got xml-apis.jar, xercesImp.jar. They got modified from old ones. So this is breaking toplink sessions.xml load to work.
Did you face this problem?
Thanks
Praveen

Replacing tunes in iTunes in computer with new hard disk

I recently had to replace my hard disk. I have authorized my computer (same as old one, but with new hard disk). Can't unauthorize the previous one. But want to transfer the music (from my CDs) currently on my iPod to iTunes on my computer. Having problems doing this. Any way to do so? Thanks.

Connect your iPod to your computer. If it is set to update automatically you'll get a message that it is linked to a different library and asking if you want to link to this one and replace all your songs etc, press "Cancel". Pressing "Erase and Sync" will irretrievably remove all the songs from your iPod. When your iPod appears in the iTunes source list change the update setting to manual, that will let you use our iPod without the risk of accidentally erasing it. Check the "manually manage music and videos" box in Summary then press the Apply button. Also when using most of the utilities listed below your iPod needs to be enabled for disc use, changing to manual update will do this by default: Managing content manually on iPod and iPhone
Once you are safely connected there are a few things you can do to restore your iTunes from the iPod. If you have any iTunes Music Store purchases the transfer of purchased content from the iPod to authorised computers was introduced with iTunes 7. You'll find details in this article: Copying iTunes Store purchases from your iPod or iPhone to a computer
The transfer of content from sources such as songs imported from CD is designed by default to be one way from iTunes to iPod. However there are a number of third party utilities that you can use to retrieve the music files and playlists from your iPod. You'll find that they have varying degrees of functionality and some will transfer movies, videos, photos, podcasts and games as well. Have a look at the web pages and documentation, this is just a small selection of what's available, they are generally quite straightforward. You can read reviews and comparisons of some of them here:
Wired News - Rescue Your Stranded Tunes
Comparison of iPod managers
TuneJack Windows Only (iPhone and iPod Touch compatible)
iPod2PC Windows Only
iDump Windows Only
SharePod Windows Only
iPodRip Mac & Windows
YamiPod Mac and Windows
Music Rescue Mac & Windows
iPod Music Liberator Mac & Windows
Floola Mac & Windows
iGadget Mac & Windows (iPhone and iPod Touch compatible)
iRepo Mac & Windows (iPhone and iPod Touch compatible)
iPod Access Mac & Windows (iPhone and iPod Touch compatible)
TouchCopy Mac & Windows (iPhone and iPod Touch compatible)
There's also a manual method of copying songs from your iPod to a Mac or PC. The procedure is a bit involved and won't recover playlists but if you're interested it's available on page 2 at this link: Copying Content from your iPod to your Computer - The Definitive Guide
Whichever of these retrieval methods you choose, keep your iPod in manual mode until you have reloaded your iTunes and you are happy with your playlists etc then it will be safe to return it auto-sync. I would also advise that you get yourself an external hard drive and back your stuff up, relying on an iPod as your sole backup is not a good idea and external drives are comparatively inexpensive these days, you can get loads of storage for a reasonable outlay.
Message was edited by: Zevoneer

Satellite M40-129: PCMCIA Card doesn't work with Linux

I have D-Link DWL-G650 with Atheros Chipset which is good supported under linux (madwifi). But if I boot Linux the card is not found. I tested the card with an Fujitsu Siemens Notebook and it worked out of the box!
Any idea why it doesn't work with my M40-129 ?

Hi
Like you know Toshiba doesnt support the Linux and there are no Toshiba drivers for the Linux OS but I was able to find this useful Toshiba page about the notebook configuration with Linux:
http://newsletter.toshiba-tro.de/main/
You should check the OS machine compatibility and the other areas.
Im sure you will find many useful tips.
Good luck

Seems RTL8192EE wireless card doesn't work with Linux 3.19

Hi all, I just fresh installed ArchLinux on my new Thinkpad T450s. The installation has been smooth enough. I can use wifi-menu on ArchISO image (which is based on kernel 3.18.6) to get my wifi connected. Everything works great. But when I reboot into the new hard disk installation, the WiFi connection always fails.
I have tried to connect manually via wpa_supplicant and dhcpcd. It didn't show any error information like driver issue or so. The problem I can see is the link is really slow: too slow to get authenticated by router. At a small chance I can connect to the WiFi but then failed to get dhcpcd work. And at a really really small chance I can get an IP from the router but the ping latency to gateway is about seconds, so I cannot visit any service via this network.
This issue happens to Linux 3.19. I have tested on 3.19.2 in core and 3.19.3 in testing.
Is there any of you have the same issue, and is there a solution for this currently?
EDIT: typo
Last edited by sunng (2015-04-02 07:16:12)

fabiopicchi wrote:
For those using kernel 4.0, the problem is partially gone. The wireless connection doesn't randomly drops and you can always connect correctly but you can get really slow speed, and sometimes all packages are lost.
Installing this new version of the driver solves the problem:
sudo git clone http://github.com/lwfinger/rtlwifi_new.git
cd ./rtlwifi_new
sudo make
sudo make install
sudo modprobe -v rtl8192ee
Yes, rtlwifi_new works for me. I do hope this can be merged into mainline some day.

Pxie 8108 does not boot with new hard disk

Hi
I'm currently using PXIe 8108 with PXIe-1062Q.
The previous hard disk was borken so I had to install a new hard disk.
The new hard disk is fommatted as NTFS format, and it is currently mounted on 8108.
Unfortunately I don't have recovery disk avaialble so I'm trying to install Windows 7 on empty hard disk.
When you boot, the PWK OK LED light is on all the time, DRIVE orange LED is on for few seconds only when I turn the switch on.
Labview RT switches are all off, I cleared CMOS many times from the board but, the screen shows nothing.
I have tried use my DVI monitor with other device as well, and it worked so there is no problem with the monitor.
In addition, I tried to go to window safe mode by pressing F8 or Del it didn't work, so I see nothing on the screen when its booted up.
I tried to put as much information I can it will be very appreciated if you can help me with this issue please.

You said you can't get into Windows safe mode, have you installed Windows on the hard drive? Are you able to get into the BIOS for the controller?
If you aren't able to access the BIOS for the controller, it may be due to bad RAM. If you are comfortable installing RAM and you have some extra laptop RAM of the same type (I think it's DDR3 for your controller) laying around, you can try swapping out the RAM.
Was your hard drive damaged through some event, or did it just stop working?
AC - LV Solver

ESATA express card does not work with Mavericks. Any suggestions?

This is an Apiotek II 300 Express Adapter. I went out to Apiotek.com and it appears the domain is for sale. Is there any way to get a software update or do I have to buy a new Express Card that allows eSATA drives to work with Mavericks. I did a backup before I upgraded using X 10.7.5 and everything worked fine. The eSATA drive is not seen using Disk Utility either.
Thanks for any help or suggestions.

The driver has to come from the manufacturer of the card, so your two options are to get another card or to use your full backup to go back to 10.7.5. That assumes it's a clone backup and not Time Machine.

Why my new Mac mini DVI dual link mini display port adapter doesn't work with my 30"display (LG W3000H)?

Hello There
Can any of you advise on the below? Tried to connect Mac mini with a 30" display through a DVI dual link mini display port adapter. For the first try Mac mini go connected to the display, then i've chosen the highest resolution (2560x1600, native) and right at that moment they got disconected. Since then the display stays black. What can be the issue, is it possible DVI dual link mini display port adapter is not compatible with 30"display (LG W3000H)? It works with DVI male-male cable plus DVI HDMI adapter as long as the resolution stays under 1280x800. Any idea is much appreciated.
Thank you, Vera

Hi,
I can report that my Mac Mini Intel Duo connected instantly and without even having to set it up (on the first try) with my 1366x768 native resolution DELL 50" Plasma Display. It's so beautiful that I just want to stand there and fondle my HDTV as I drool haplessly like Homer Simpson with a doughnut in his mouth. Seriously, no problems.... guess I bought the right cable (ebay).
Before you buy a Duo, make sure you're aware of the airport and bluetooth issues that so many (maybe everyone who tries to use them together) are having. It seems that bluetooth interferes with airport, or maybe the other way around. Anyway, it's messed up. Also, Airport reception is generally VERY poor with the new Intel Mac Mini.
Despite these things, I still love mine (I now have 2 base stations and an airport express for my powerhouse wireless needs, and an external DLink bluetooth-2-USB dongle solved the bluetooth/airport issues... in my case).
FWIW,
awk
667-MHz Ti PowerBook G4. Mac OS X (10.3.9)

Globe SIM card doesn't work with my iPad

I really desire to use my iPad as my alternate Text messaging gadget but the problem is my Globe micro-SIM doesn't work on it. The name and Signal strength of my Telco, however, do appear on the upper left corner of my iPad. I cannot send text messages from my iPad using my Local service provider (Globe Telecoms Philippines). Any suggested solution to my problem, please...

The micro-SIM on an iPad is used only for internet data connection (web browsing, email, etc.), not SMS or voice.
Depending on what facilities are available to the people with whom you wish to communicate, you might be able to use one of the many internet-based forms of messaging. (For example, iMessage within the Apple ecosystem, AIM, Jabber, or GoogleTalk.)

Wireless Music doesn't work with new software

Hello-
I can't get my wireless music to work after I update the software to the latest version. The only one that will work is when I install it from the CD. But, I would like to use the most recent version of the software. As soon as I update, the Media Server won't launch on my computer. I am using a linksys WRT54G wireless router. If I check DHCP clients, the wireless music receiver is successfully getting an IP address. I have tried all of the things that linksys suggested (disable WEP, firewall, broadcast SSID, etc...) to no avail. Has anyone gotten the latest media server software to work with WRT54G? I have tried it on both my XP and W2K machine, with the same results (doesn't work).
Thanks,
Rich

Hi Jeremy
I have the similar problem, I've installed the software on my desktop, no error messages (apart from the certificate) and everything seems to be fine. After about 2 minutes the message appears that the network is not ready and consequently the media server is not running.
Without the server running I can't setup the Network and the entire system is not working. I could ping it but that was about it.
I've reset my router, renamed the SSID, tried with and without WEP, MAC, without firewall, opened a new account on my desktop with admin rights installed the software again into a new folder - result still not working, same error message.
To make really bad, I installed it on my laptop, same procedure and it works fine! So it seem that it has nothing to do with my wireless devices or configurations, there must be a problem while setting up the software on my desktop.
I really would appreciate your help a lot!

Cheers

Balz

Can't get GeForce GTX 560 Ti card CUDA to work with new Premiere Pro CC 2014 version

In the past I've been able to get CUDA on my GeForce GTX 560 Ti card to work with Mercury Playback engine by adding "GeForce GTX 560 Ti" to the cuda_supported_cards.txt file. But with the new CC 2014 version of Premiere, that file isn't in the Premiere Pro directory anymore. Is there a way to get my GTX 560 Ti to be listed as a CUDA-supported card with CC 2014?

Okay, I figured it out. I installed the latest graphics driver and then opened the NVIDIA control panel. In there I selected "Manage 3D settings" and went to the "program settings" tab. I selected Adobe Premiere (adobe premiere pro.exe) from the list and under the "CUDA - GPUs" feature, I changed it to "Use these GPUs" and selected my GTX 560 Ti (which was the only one listed).
After doing that, I opened Premiere Pro CC 2014 and selected "Project Settings - General" and was then able to choose "Mercury Playback Engine GPU Acceleration" under Renderer (which had previously been unavailable).
Hopefully this will help someone else if they encounter the same problem.

Recovery discs do not work with new hard drive

Hi I have come here desperately seeking help as I am not too knowledgeable with the workings of computers and I have spent an incredible amount of time just trying to get my laptop to some level of functionality. I purchased a HP Envy and it had a corrupt hard drive which would not work from day one, laptop was new. After a year of constant pressure on HP they finally decided to replace it and let me choose any laptop so I went with the Beats Envy 14 as it was the best one offered from the selection. Low and behold the thing would not work properly from day one, again my brother who is much more of an expert said that there was definitely a hard drive issue so for the past 3 years I have put up with a computer that constantly crashes with BSOD, where I have lost data on numerous occasions (only so often I can back up), that I have had to constantly reset the thing using HP recovery discs, and that generally cannot cope when performing multiple tasks. HP are most certainly shocking builds from my experience. Then just last week the hard drive just craps itself and the laptop no longer will boot up. I took it to a guy to get it at leYst working again so he has installed a new hard drive but with an old version of Windows 7. I want to go back to the Windows version I was akin to on the HP recovery disk , and essentially have it all set up as before except for now having a workable hard drive however I get the message: "This computer is not supported by the System Recovery Discs.You will not be able to continue to recover this system with these discs.Error: 0100 - 3385 - 3078" I also tried out of interest to load my old Windows 7 disc I had and XP but had no success. Tried booting from startup etc and various things suggested on help forums. Please tell me I am not stuck with this version of windows. Whilst the discs included Windows 7 it was a totally different version, this home premium one is terrible. Any help/advice would be gratefully received. Thanks

no they were both 500gb. I read about that already, I heard about creating a partition for recovery etc but this is all a bit above me , as I said I am not very technical when it comes to the working of a computer. These discs worked perfectly before but now with the new hard drive will not load at all. I essentially hate the Windows Home Premium verions the guy who fixed it put on, whilst the discs had Windows 7 on them the icons were way smaller, the desktop neater, the buttons different, everything was a lot more modern and I was used to it. This version looks like something from the 90s, have to constantly adjust size of Mozilla when browsing as it is huge. I have my own version of Windows 7 on another disc but the hard drive will not let it load either........considering waiting for Windows 10 but again unsure if this new hard drive will even let that update Thanks

Recovery did not work with new hard drive

The original Toshiba HD(250G, sata1) of my laptop( ) crashed.
I bought new one (320G, sata 2, Western digit )
The problem is that, when I tried to use the recovery CD that I used to use it with old HD before, it did not work with this new HD well!?
After cd1 and cd2 finish installing it ask to take it out then restart, I do so, but when it comes to setup setting of windows.
An error message come out says " Windows Setup could not configure Windows on this computer’s hardware”
It restart and says again " Windows could not complete the installation. To install Windows on theis compuiter, restart the installation."
I have been trying to solve this a lot, but no way
I tried what in this link, but it drive me with another problem http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-could-not-complet...
I hope that I get the right thing to do, from ur forum by this post.
Thanks a lot

Did you folks search here for "advanced format drive"? People have had numerous weird problems with the new advanced format hard drives in older Toshibas. I can't look up all the threads for you. But here is one:
http://forums.toshiba.com/t5/System-Recovery-and-Recovery/Recovery-won-t-work-on-new-upgraded-hardri...

Intel Wireless Card doesn't work with Linksys?

My wired computer works great with the WRT54GX2, but my wireless cannot hold a signal for very long. Support says they can't help me because I have a Intel wireless card. Intel does not support for that card anymore and I can't see where to buy a Linksys card. Please, help.
Bonnie

check the link for the linksys retailers
Retailers
Message Edited by Maximus on 07-21-2006 05:48 PM
I do know everything, just not all at once. It's a virtual memory problem.

MacPro eSata Port/Card doesn't work with new Hard Disk

Similar Messages

Maybe you are looking for