Magsafe light is dim green and not charging properly

Hello all,
I am hoping that someone could help me out with this. I have a Mackbook unibody from 2008 with the most curent Lion operating system. I recently started having problems with the charing of my laptop. I was using my computer one day to the point that the batery got used up and the laptop turned off. When I brought it home to charge the magsafe light turned on very dim green. It took 4hours for me to be able to start up my computer and has taken 3 days to get to 90% charge which it does not seem to go over. Bellow I have pasted information about my battery which is about 8 months old (new one i bought from apple). For some reason if you look down in the battery information, it's saying that it's not charging. I don't have apple care and money to fix it, any advice would go a long way.
  Fully Charged:    No
  Charging:    No
Battery Information:
  Model Information:
  Serial Number:    9G8******13DB
  Manufacturer:    DP
  Device Name:    bq20z951
  Pack Lot Code:    0
  PCB Lot Code:    0
  Firmware Version:    002a
  Hardware Revision:    5
  Cell Revision:    100
  Charge Information:
  Charge Remaining (mAh):    3787
  Fully Charged:    No
  Charging:    No
  Full Charge Capacity (mAh):    4217
  Health Information:
  Cycle Count:    59
  Condition:    Normal
  Battery Installed:    Yes
  Amperage (mA):    119
  Voltage (mV):    12291
System Power Settings:
  AC Power:
  System Sleep Timer (Minutes):    0
  Disk Sleep Timer (Minutes):    0
  Display Sleep Timer (Minutes):    0
  Automatic Restart on Power Loss:    No
  Wake on AC Change:    No
  Wake on Clamshell Open:    Yes
  Wake on LAN:    No
  Display Sleep Uses Dim:    No
  PrioritizeNetworkReachabilityOverSleep:    0
  RestartAfterKernelPanic:    157680000
  Battery Power:
  System Sleep Timer (Minutes):    0
  Disk Sleep Timer (Minutes):    0
  Display Sleep Timer (Minutes):    0
  Wake on AC Change:    No
  Wake on Clamshell Open:    Yes
  Current Power Source:    Yes
  Display Sleep Uses Dim:    Yes
  Reduce Brightness:    Yes
  RestartAfterKernelPanic:    157680000
Hardware Configuration:
  UPS Installed:    No
AC Charger Information:
  Connected:    No
  Charging:    No
Message was edited by: Host

That battery information looks decent, low number of cycles, capacity is about right for that vintage battery, condition is Nromal as it should be, and the voltage is right where you want it, 12 to 12.5 volts.
Have you worked through the knowledge base article on MagSafe connectors to see all is healthy on that end?
If that is fine, then it could be an issue in the charging circuitry in the MB.  In which case it would be best to have an Apple tech at the genius bar run some diagnostics.

Similar Messages

  • My macbook pro magsafe stays green and wont charge ,what should i do ?

    THe magsafe light stays green ,and wont charge even after 2 hours ,and whe i plug in the orange light does not appear

    Let the battery drain to say 90% and then put in the charger, it should charge to 100%.
    When you put the charger in when the battery is 95% or higher, it will not charge, the light stays green and the battery will stay at the percentage it has.
    If charging does not start when the battery is low, there is something amiss: do the SMC reset.
    Lex

  • Macbook Pro Late 2008 not recognizing battery and not charging

    Hello
    i really need some help please
    i have a Macbook pro 15" Late 2008 running os x 10.7.4
    i will say briefly how did the problem begin and what is the problem
    it stopped charging for some reason the magsafe light was (and still is) dim green and at the battery icon it said not charging but after a couple of hours that it was turned off and connected i found out it is charging really slowly
    later on that week
    i was using an app called DSLR remote connected to my camera i left my macbook on the table outside connected via usb to my camera waited on it and came back
    when i came back my mac was out of battery
    i took it in hook it up to the magsafe nada nothing not charging dim light
    so what i did i knew my magsafe charger is ready to be changed so i bought a new one
    tried it same problem
    later on did an smc reset
    it did turn on biw the fans are really loud the battery icon (x) and it said no batteries available
    so i tried my old fastly drained battery it used to hold up about 1-2 hours then i bought another battery but that was in the past
    so i tried both batteries smc reseting with both same result
    the smcfancontrol app says fan speed 000 rpm and temoerature 0 C
    and one more thing when the mac is off and not connected to the magsafe i click on the battery indicator light on the left side i get a flashing light (battery empty needs to be charged) when i connect the magsafe it stops working even when its off and while its just connected
    so it is and SMC problem
    it has been like that for the past 4 weeks or so
    i really need some help
    and im from israel so no apple genius bars around =_= and i have a good technical knowledge
    Sincerely, Sari Hassoun

    its not about solving or not its about trying to
    i understand nobody wants to make any harm to my macbook
    thats reasonable
    anyway its a hardware faliure of some sort i'll need to check it my self but now im almost sure its not software because i've tried many things
    my other option is to run it off a battery
    the thing is my battery is out so when its attached the battey indicator lights do work (they are controled by the SMC) that might solve it too
    thanks for replying really
    its appreciated

  • Battery 0% and Not Charging

    The battery in my mid 2010 13" Macbook Pro was getting low so I grbbed my 85W power adapter and plugged it in, but there was no light. I tried unplugging and reconnecting it in different directions but still nothing. I figured the power adapter was dead so I purchased a new 60W adapter and it won't charge the computer either. On both adapter the Battery Condition reads Normal and Battery is Not Charging. When plugged in with the 60W Power Source is Listed as the Power Adapter and when plugged into the 85W it is listed as running on batery. My battery is now at 0% and Not Charging. I have tried resetting the SMC but it didn't help. What should I do now?

    Hi Shadow351,
    If you are having battery or charging issues with your MacBook Pro, you may find the troubleshooting portion of the following article helpful:
    Mac notebooks: All about batteries
    http://support.apple.com/kb/ht1446
    Regards,
    - Brenden

  • My iphone 4 is not being detected by any of my computers and not charging when connected to any computer.  It will, however, charge to the car or wall.  The only change that I can think of is that I downloaded a podcast from itunes directly from my phone.

    My iphone 4 is not being detected by any of my computers and not charging when connected to any computer.  It will, however, charge to the car or wall.  The only change that I can think of is that I downloaded a podcast from itunes directly from my phone.  I've since deleted this podcast with no luck.  I've restarted both the phone and the computer, still no luck.  One computer is running Vista and the other Windows 7, both have the latest Itunes Update.  Anyone have a fix for this?

    You clearly did not notice that you have joined a USER TO USER COMMUNITY FORUM
    This is NOT Apple ,Apple do not read nor do they  therefore respond
    So if you would like to wind your neck in ........................
    try a reset of iPhone and then a restore,best, as new and if it then functions correctly try restoring with your backup

  • IPod Touch (2nd Gen) not charging properly and apps won't update

    Hi, I'm not really sure if or how these problems can be linked, but I thought I'd put them together just in case...
    My first problem is that my apps aren't updating properly.  When I try to apply the updates, I get the "waiting" come up but then it just resets having done nothing, sometimes needing me to switch my iPod right off and on again before I can use the app again.  I tried connecting my iPod up to my computer to apply the updates through iTunes and it seemed to work, but none of them actually updated.
    Having connected to iTunes and tried to sync everything, I also got an error message saying that the apps couldn't be synched due to not being able to determine what apps were on my iPod.  However, they were all sitting there looking like they had synched.
    The second part of the problem is that my iPod doesn't seem to be charging properly anymore.  The battery doesn't seem to be lasting as long as it should and I've noticed that sometimes when I'm charging it, I get the symbol come up that means it's running from the mains, when it should actually still be the symbol to show it's currenty charging, so I'm wondering if the problem is that it's not charging properly some of the time rather than the charge isn't lasting long enough.
    If anyone's got any ideas how to resolve any of this I'd really appreciate it
    Thank you
    amethystar

    Sounds like your power receptacle jack may be bad. See repair options in link below.
    Troubleshooting 101
    Some topics covered
    -Basic troubleshooting steps
    -Hard reset instructions
    -Manual restore instructions
    -Hardware troubleshooting
    -Preventive Maintenance
    -Anti-theft & recovery tips
    -Battery-saving tips
    -Repair options
    -Contacting Apple
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G HD + OCZ Vertex 3 SSD Boot HD 
    Got problems with your Apple iDevice-like iPhone, iPad or iPod touch? Try Troubleshooting 101
     In Memory of Steve Jobs 

  • When I plug my ipad in to charge its just coming up with a red bar in the charge icon and not charging

    When i plug in my ipad to charge its just coming up with a red bar in the recharge icon and not charging.... what does this mean and how can it be fixed... checked all cables, not broken

    First make sure you are using the charger that came with the iPad and plug that into a good wall outlet. When the iPad battery is completely drained it may take some time on the charger before the iPad responds. Be patient and let the iPad remain on the charger for at least an hour then reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart. If the iPad restarts let it continue to charge until the battery is at 100%. If the iPad does not restart Make an appointment at an Apple Store to have your device examined by a technician. Or contact Apple Support.

  • My iphone 5 display has been cracked and not charging too. I cant even power on my phone. I have applecare too. what the best I could do regarding this matter. I live Australia

    My iphone 5 display has been cracked and not charging too. I cant even power on my phone. I have applecare too. what the best I could do regarding this matter?
    I live in Australia.

    well my display was cracked like ages ago.. I don realy care about my display. so wud I be able to replace my iphone due to battery problem? cause I have apple care..
    Thanks for helping..

  • G 505S "Plugged in and not charging" (Tried everything!!!)

    Hi everyone!
    I hope someone in the community can help me out. I've tried calling in to Lenovo and I've only been disapointed and VERY ANGRY with Lenovo so I hope someone here can help me.
    My G505s has never properly charged the battery. The battery icon says "plugged in and not charging". I've tried everything, replacing the battery, uninstalling the Microsoft Battery driver, uninstalling Lenovo energy management etc.
    I've tried the work arounds I've found online to no sucess.
    Does anyone have any ideas? Has anyone ran in to this with the G505s and found a fix?
    Thanks!

    hi apb1019
    Welcome to the Lenovo Forums and sorry to hear about your battery problem.
    The plugged-in not charging message is usually triggered when the Lenovo Energy Management / Lenovo Energy Manager is set to Optimized Batteyr Health (Win8) or Conservation Mode (Win8.1)
      - Link to picture
      - Link to picture
    Just to verify:
    1. When you uninstalled the energy management software, are you getting a 0% available, plugged-in not charging message or 60% available, plugged-in not charing ?
     - Link to picture
    2. Have you tried charging the battery (for an hour or two) while the computer is off?
      - Link to picture
    If the battery doesn't get fully charge while the computer is off then it's likely that the battery is failing. In this case, I recommend you contact Lenovo one more time on how to go about getting the unit serviced (they'll most likely send you a new battery).
    Regards
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • HT201263 I tried to reset my iPhone (3gs) with deleting all data. When it power off and automatically again on then it is showing Apple logo only. Not restore and startup my phone. I tried to charge and not charging. What I should do now?

    I tried to reset my iPhone (3gs) with deleting all data. When it power off and automatically again on then it is showing Apple logo only. Not restore and startup my phone. iPhone alerming low charge and I tried to charge and not charging.
    What I should do now?

    Something has gone wrong. Turn your phone off, then force it into recovery mode:
    Leave the USB cable connected to your computer, but NOT your phone, iTunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new. In your case, select "new".

  • X1 (1286) main battery good condition at 1% and not charging

    Hello,
    I recently noticed that the main battery is no longer charging. It is now at 1% and not charging when AC plugged in (screenshots of powermanager attached). Power Mgr says it is in good condition. Since I usually have the slice battery attached on the road or AC plugged in at home, it has always been in Optmize for Health mode.
    The battery gauge reset procedure was performed and hasn't helped.
    I've run the battery firmware update utility and it has stated that battery firmware is up to date.
    And as always the case, 1yr warranty expired  3weeks ago 
    I'll try updating BIOS (1.66) to latest, which I believe is 1.69, and post back if any success. 
    Any clues please? Thanking you in advance. 
    Link to image 1
    Link to image 2
    Details from msinfo32:
    OS Name Microsoft Windows 7 Professional N
    Version 6.1.7601 Service Pack 1 Build 7601
    OS Manufacturer Microsoft Corporation
    System Name THINKX1
    System Manufacturer LENOVO
    System Model 1286CTO
    System Type x64-based PC
    Processor Intel(R) Core(TM) i7-2640M CPU @ 2.80GHz, 2801 Mhz, 2 Core(s), 4 Logical Processor(s)
    BIOS Version/Date LENOVO 8MET66WW (1.66 ), 26/06/2012
    SMBIOS Version 2.6
    Windows Directory C:\Windows
    System Directory C:\Windows\system32
    Boot Device \Device\HarddiskVolume1
    Locale Australia
    Hardware Abstraction Layer Version = "6.1.7601.17514"
    Time Zone AUS Eastern Standard Time
    Installed Physical Memory (RAM) 8.00 GB
    Total Physical Memory 7.89 GB
    Available Physical Memory 5.07 GB
    Total Virtual Memory 15.8 GB
    Available Virtual Memory 12.8 GB
    Page File Space 7.89 GB
    Page File C:\pagefile.sys
    Moderator note: images totalling more than 50k converted to links per forum rules:  Lenovo Community Participation Rules

    Thanks for responding Jin and helping out.
    Unfortunately updating bios and power manager hasn't resolved this. The new version of power manager 6.54 dispays same battery details.
    Furthermore, i am now noticing that the slice battery charges to only 80%  despite setting charge mode to fully charge. Could be experiencing this problem (x1 slice battery won't pass 80% unless internal battery is 100%) too, unfortunately no answers to that post.
    In the process to updating drivers via LSC but not holding my breath 

  • Day after yesterday night, my iphone 4s full off, I don't know why? but not oppen and not charging. What do I do?

    Day after yesterday night, my iphone 4s full off, I don't know why? but not oppen and not charging. What do I do?

    Plug it in to power for at least 15 minutes.  If it doesn't automatically come on, try a Reset... press the home and sleep/lock buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.

  • I am trying to make a purchase and want to use my Apple ID Balance and NOT charge the debit card under my account info.  How do I do this?

    I am trying to make a purchase and want to use my Apple ID Balance and NOT charge the debit card under my account info.  How do I do this?

    As far as I'm aware iTunes always charges the account balance first and when this expires charges any remaining amount to your credit/debit card. The one exception I am aware of (though there could be others) is that Apps purchased from the Canadian store must always be charged to a card rather than a gift card voucher balance due to local legislation.
    tt2

  • My iphone 4 switches off unexpectedly and does not charge properly every time

    My iphone 4 turns off unexpectedly and does not charge properly every time. Can anyone help

    Hey bigstu29,
    Thanks for the question. To completely isolate the issue, you may want to follow these steps:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    - Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    - Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion.
    Learn about LCIs and corrosion.
    - Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    - After at least 15 minutes, if:
                   - The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
                   - The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
                   - Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    - If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
                   - If the display turns on, go to step 4.
                   - If the display remains black, go to next step.
    - Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to
    restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    - If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    For additional information, see this article:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Thanks,
    Matt M.

  • I cannot receive texts on my phone.  They are coming into my iPad.  What happened?  I can send texts, but they are now green and not the blue color.  ??

    I cannot receive texts on my phone.  They are coming into my iPad.  What happened?  I can send texts, but they are now green and not the blue color.  ??

    Turn iMessage on for your devices.
    Settings > Messages > iMessage.

Maybe you are looking for