Mail Problems before and after 10.4.6

On Friday, running under 10.4.5, Mail started acting strangely (it would have the gray wheel around my main accounts -- from two different servers). I would have to force quit. At the same time, address book stopped opening (it would require a force quit as well) and iCal similarly began to have problems (it would not accept new events and would also require a force quit). I upgraded to 10.4.6 and now Mail (2.08) will not open at all and the other problems continue. I have verified the permissions. there is plenty of free space. I am not keen to reinstall and since the problem occurred without any other apparent problem, I wonder if anyone has a solution.
MacBook Pro Mac OS X (10.4.5) Actually 10.4.6

I'm having the exact same problems -- plus Safari is repeatedly crashing. Strangely, it's only happening on one side of the two user set up!!
I reinstalled OS 10.4.5 Monday (4/3) to try to fix the Mail issue, and later that night 10.4.6 was automatically downloaded and installed. That's when the other problems started.
Question: Are fresh versions of just Mail 2.0.8 and Safari 2.0.3 (or later) ONLY available for downloading somewhere?
On Friday, running under 10.4.5, Mail started acting
strangely (it would have the gray wheel around my
main accounts -- from two different servers). I
would have to force quit. At the same time, address
book stopped opening (it would require a force quit
as well) and iCal similarly began to have problems
(it would not accept new events and would also
require a force quit). I upgraded to 10.4.6 and now
Mail (2.08) will not open at all and the other
problems continue. I have verified the permissions.
there is plenty of free space. I am not keen to
reinstall and since the problem occurred without any
other apparent problem, I wonder if anyone has a
solution.
MacBook Pro
Mac OS X (10.4.5) Actually 10.4.6

Similar Messages

Problems before and after Uninstall and re-install CS4

I went ahead and uninstalled and re-installed CS4 because of freeze ups and other difficulties. Program After Effects is now crashing - see attachment. There is also a problem with an importer plugin (I think) may be related. I can't tell. I have not tried any other projects. I did however, disconnect the Matrox MX02 Mini, but still had problems. The MX02 is now re-connected.
I wonder if installing CS4 on top of CS3 is an issue? I remember having a similar problem goiing from CS2 to CS3. I had to downloader a cleaning utility from Adobe (I think) to remove every bit of CS2 and then run CCleaner.
It's my own fault - trying to upgrade software and hardware at the same time. It's hard to isolate. For now, I'l just have to do with Premiere since it is working. But, I'd sure like to know what's going on.

Did you re-install all other Adobe products as well? If not, then that may be the problem. Uninstalling/ reinstalling only one of them messes with MediaCore and certain otehr functions. The quick fix is to download the manuala (!) update packages for After Effects, Premiere Pro/Encore and Adobe Media Encoder from the support pages and run them. This usually bends things in place. If not, then you will probably have to uninstall again, this time including every Adobe app, use the CS4 Clean Script and reinstall.
Mylenium

N8 problem before and after ANNA update

Dear Gent's in Nokia,
Me and my 2 friends have same mobile "nokia N8". When we purchased phones we have had one very annoying problem , phone resets 1-2 times during the 48hours and always happens when we try to call someone . We have been patient and waited for ANNA update . Finally when arrived we have updated our phones and now we have similar problem ,it's connected with calls again.When we try to call someone phone does'nt resets it says "Call not allowed", this thing happens randomly at least once a day , then we have to turn the phone off and then turn it on so we can make calls again. It happens on three N8 same problem.
Can somebody help us with this problem?
Thank You in advance

Nokia made it possible to re-install the ANNA software,
Connect to OVI SUITE 3.1.1.9 (Updated version 20 September 2011)
Search for new updates
& select : re-install
see more about this issue :
http://forums.techarena.in/portable-devices/1430136.htm

TS1424 Hi I had this problem before and you fixed it. I just bought the updated phone and have no mail and it says me itunes purchases are disabled. Can you help me??????????????????

Hi I had this problem before and you helped fix it. I just bought an updated Iphone and now it says my itunes purchases are disabled. They also put spelled my name wrong and I do not have any mail coming thru. Please help me!!!!

We are fellow users here on these forums, you're not talking to iTunes Support nor Apple.
If your account is disabled (I assume that it what you mean by 'my itunes purchases are disabled') then you might be able to re-enable it via this page : http://appleid.apple.com, then 'reset your password'
If you aren't receiving the email to your rescue email account then you can contact iTunes Support / Apple in your country via this page and see if they can enable it : http://support.apple.com/kb/HT5699
You might then need to log out of your account on your phone by tapping on your id in Settings > iTunes & App Store and then log back in so as to 'refresh' the account on it.
Not sure what you mean by 'they also spelled my name wrong' - where are you seeing it ? Your name should be appearing how you entered it.

GREP: How can I place a (for example) "*" before and after bold text with GREP?

Hi there.
I have a string of text as such:
I want to use GREP to insert a "*" (asterisk) before and after each bold part. Can I do that with GREP?
(if asterisk is a problem, I can use a different character)
Any help would be appreciated.

Hi Schmaltzkopf,
try this:
Have fun

My phone is not working at all. I had this problem before and I was trying to find a solution. However, at Apple Store in UK I was told to send my phone to Canada due to fact that I bought it there. What should I do and who will cover all my payments?

Hello,
My phone is not working at all. I had this problem before and I was trying to find a solution. However, at Apple Store in UK I was told to send my phone to Canada due to fact that I bought it there. What should I do and who will cover all my payments for a mail?
Thank you!

The iphone warranty is not international. It is based from the original country of purchase. You will need to ship to someone you know in the Canada to bring it to Apple for evaluation. Then that person will have to ship the phone back to you. Shipping and insurance will be at your expense. In the terms of the iphone warranty:
http://images.apple.com/legal/warranty/docs/iPhone_4_warranty.pdf
IMPORTANT RESTRICTION
Apple may restrict warranty service to the country where Apple or its Authorized Distributors
originally sold the Apple Product.

Compare BEFORE and AFTER image in replicat

Do any of You experts know how to make the following code smaller?
...,p_kolonner=@STRCAT("ID='",@IF(@COLTEST(BEFORE.ID,PRESENT),BEFORE.ID,""),"'>'",@IF(@COLTEST(ID,PRESENT),ID,""),"'¤",
"OBSOLETED_ON='",@IF(@COLTEST(BEFORE.OBSOLETED_ON,PRESENT),BEFORE.OBSOLETED_ON,""),"'>'",@IF(@COLTEST(OBSOLETED_ON,PRESENT),OBSOLETED_ON,""),"'¤",
"SMRT_ID='",@IF(@COLTEST(BEFORE...The actual parameter would look like:
P_KOLONNER: ID=''>'11531'¤OBSOLETED_ON=''>''¤SMRT_ID=''>'1'¤SM_SMID=''>'2011X0074-00'¤SMT_ID=''>''...
This code is part of the params section of a sqlexec in a replicat file where I want to concatenate before and after images of a table into one parameter. I have to replace all NULLs with '' or the whole string evaluates to NULL when one of the columns are NULL. I have a procedure receiving the parameter.
How do I write this code shorter? I have to use less code to accomplish the same thing.

Hi Yosemite:
You're right, the correct term is "Key Fields", in the previous post I made a mistake when referring to it as "Key Part", I'm sorry for the confusion.
Anyway, it is not clear to me if you managed to solve the problem or if you're still struggling with your data loads, if this is the case, Could you please elaborate?
-Which is the data source you are working with?
-Did you map the ROCANCEL field both to the 0STORNO and 0RECORDMODE InfoObjects?
-Are you using Addition or Overwrite on the Update Rules/Transformation Rules to the DSO?
-Have you applied any relevant SAP Note to fix this issue?
In case you have not read the blog by Swapna Gollakota, take a look at it, you might find it useful.
How does a datasource communicates "DELTA" with BW?
/people/swapna.gollakota/blog/2007/12/27/how-does-a-datasource-communicates-delta-with-bw
Regards,
Francisco Milán.
Edited by: Francisco Milan on Oct 29, 2010 12:31 PM

Everyone: This time repair your permissions before and after 10.4.8 update

Hello All,
Just a reminder for all those who are updating to OS 10.4.8.
While many people do ignore all the recommendations that we provide and still come through fine, please do consider observing the following to minimize your problems.
To insure the best chance of success, please consider downloading the Combo Updater for your computer instead of using Software update.
For PowerPC Mac's, this would be:
http://www.apple.com/support/downloads/macosx1048comboupdateppc.html
For Intel Macs, this would be:
http://www.apple.com/support/downloads/macosx1048comboupdateintel.html
The benefit of using the Combo Updater, is that it replaces all system files that have been changed since the last major release (in this case since 10.4.0).
So, if you have any system files that have become corrupted, the Combo Updater will very likely over-write those, and spare you the headaches that come from updating an operating system that has problems that just haven't come to the surface yet.
In many cases, you can have problems that have not come to the surface, and the "Delta" or Software update method will bring them out to bite you. The reason for this, is because the Delta / Software Update version only changes files that have changed since 10.4.7. And, it works more in a "patch" fashion. So, if there is a problem in one of the files being patched, then the update will cause you some major headaches.
Going with the larger "Combo" update over-writes almost all the System files with clean versions instead of just making patches. So, it is frequently much more successful.
Now, with that said, before you update, you should make sure your permissions are all set properly. If your permissions are wrong, then your update will likely have trouble.
So, go into "Disk Utility" in the Applications --> Utilities folder and repair your permissions.
Start by selecting your hard drive on the left window of Disk Utility. Then, go down and click on the "Repair Permissions" button. Once it's completed, then exit Disk Utility.
Now, it is also extremely important to make sure all running programs are closed before you install any system update. So, go ahead and restart your computer.
Restarting will make sure that all programs are closed, and that nothing weird is stuck in memory before you install.
If you have anti-virus programs running, then disable or deactivate them first (you don't want them interpreting this as unauthorized modification or it might prevent certain files from being updated).
Now, with your computer freshly restarted, install the Combo updater you downloaded.
When prompted, click on the "Restart" button when prompted.
Now, the computer will startup, but sit at the spinning wheel for several minutes. It will eventually restart again on it's own. And, finally, it will start-up all the way and you'll be back at your desktop.
Now, immediately go back to Disk Utility and repair permissions as you did in the previous step. You will likely see several permissions that have been repaired. In my case, I had dozens of CoreAudio, Widgets, and other permissions that needed repair. Once permissions have been repaired, go ahead and restart one last time. This makes sure that everything is set and then cleaned-up.
Once it reboots, begin using it and enjoy.
Now, this may sound like a lot. But, it really is simple. It just reads like a lot of stuff.
And, of course, you are free to ignore this and just install it however you like. Many people have their own ideas here. And, many people say you don't have to do anything to prepare. But, for those that have had huge problems in the past, these extra steps will usually save you the major headaches that tons of people inevitably have with every new update.
Anyway, I hope this helps to save at least a few of you any problems. If you don't agree with the ideas above, just ignore it and do as you like.
But, if you want a little extra piece-of-mind and a better chance at success, then please consider exercising this extra caution.
And, for the record, I have updated my machines to 10.4.8 (within minutes of the update being available) and it is working perfectly smooth on my systems.
I hope you find this helpful.

mhunter, thanks and good that you take the time and effort again to remind everyone that it does take an effort to do a major OS update, to ensure maximum stability.
So far my 10.4.8 Update is a-okay, and I have had many trouble-free updates since installing 10.4
I too practice rigourously and "religiously" before and after an OS or Security Update, but I normally use Software Update, equally successful:
1. Before Startup, UNPLUG all external devices, left only keyboard, mouse and internet connection, unless they are all wireless.
2. Startup, disable NAV if any, Repair Disk Permission. Restart again, Repair Permission again.
3. Do Software Update
4. Restart, Repair Permission
5. Shutdown, plug everything back
6. Startup Mac, use Mac
So far these steps have been keeping all my macs both at home and at work very very stable and healthy.
Maybe, just maybe if everyone here, all mac users were to follow these steps, yes they can be a hassle, yes they can take up some time, but then there will be less less complains and "blasts" at Apple, just because perhaps themselves have been too careless or negligance in performing updates.
Cheers

Can we call a method before and after Export operations in ADF 11g

Hi,
My problem is I have to execute a method before and after the export operation.Is this posible in ADF 11g
Regards,
Felix

Hi,
in response to a similatr post of yours, I replied
1. Drop af:exportCollectionActionListener on a command button
2. set the command button to display = false
3. In your Java code, call
ActionEvent ae = new ActionEvent(button);
ae.queue();
Everything you put before
ActionEvent ae = new ActionEvent(button);
ae.queue();
will fires as a pre-trigger, everything after as a post trigger
Frank

I'm unable to update my apps or download new apps to my Iphone. When I try I get a message "An unknown error has occurred". It was happening before and after the last OS upgrade. I've done a hard reboot with no effect. Any suggestions???

I'm unable to update my apps or download new apps to my Iphone. When I try I get a message "An unknown error has occurred". It was happening before and after the last OS upgrade. I've done a hard reboot with no effect. Any suggestions???

Have either of you had any luck with this issue. It began happening to me today when I was trying to purchase music on iTunes. I have purchased music and games in the past and have had no problem. Any help would be appreciated.

Can I control the spacing before and after a signature?

When using the Mail app, can I control the spacing before and after a signature? It seems like the app adds space, but it doesn't add the same amount every time.
Thanks.
Greg

The only way I can think of to maintain equla spacing between the text ov vartying lengths and the vertical lines is to put each icon/text pair in it's own frame fitted to content, make each vertical line a separate object, then select them all and distribute the spacing.

Status page before and after print jobs managed by Jetdirect.

Hey Guys I am receiving an extra page before and after every print job.
Printers are managed from Jetdirect Printer Installer for Unix Version E.10.34
Server has Sun OS 5.10
I have like 19 printers but only 5 HP CB516A are having this problem.
The Print Message displayed is :
Start: fpec4050-2729 Tue Nov 11 15:41:18 EST 2014
End: fpec4050-2729 Tue Nov 11 15:41:18 EST 2014
Its not a major issue but its a nuissance and wastes pages and ink
Any assistance for a resolution to this would be helpful.
Thanks.

@deff
‎Thank you for using HP Support Forum. I have brought your issue to the appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message from an identified HP contact. Additionally, keep in mind not to publicly post ( serial numbers and case details).
If you are unfamiliar with the Forum's private messaging please click here to learn more.
Thank you,
Omar
I Work for HP

Possible to get JComboBox before and after chaged value?

Hi,
I have a JComboBox... whenever the JComboBox value change is it possible to get the before and after changed value? For example:
Let says the JComboBox is showing "One" and the user change it to "Three" after the user chged... I want to System.out.println before chged value ("One") and aft chged value ("Three")
I tried:
put in some code in the itemStateChanged() method... but no success...
Can someone pls provide some pointer or sample code...
Thank you for your time...

Ok, I lost half a day on this (novice problem), but I arranjed a solution that resolve the problem totally. There is the code:
YourComboBox.addFocusListener(new java.awt.event.FocusAdapter()
        int aux_selected;
        // if YourComboBox gains Focus
       public void focusGained(java.awt.event.FocusEvent fe)
            // get index value of selected element
           aux_selected= YourComboBox.getSelectedIndex();
           // create a variable for storing de ItemListener
          ComboBListener = new java.awt.event.ItemListener() {
               public void itemStateChanged(java.awt.event.ItemEvent e)
                   if(e.getStateChange()==java.awt.event.ItemEvent.SELECTED)
                       // compares the selected value with the old one
                       if (aux_selected!=YourComboBox.getSelectedIndex())
                       System.out.println("ComboBox Changed !");
           // add the variable Listener to your Combo
           YourComboBox.addItemListener(ComboBListener);
       // if focus is lost
       public void focusLost(java.awt.event.FocusEvent fe)
          // remove the itemListener from the combobox
         YourComboBox.removeItemListener(ComboBListener);
//Put the Listener variable outside
private java.awt.event.ItemListener ComboBListener; //----------------------------------------------------------------------------------------------------
You only have to change YourComboBox by the name of the combobox.
To all people that help this forum (specially from PORTUGAL) and all java people: YOU ARE DOING A GREAT JOB

Proble with Before and After in camera raw

The problem that I am having is the before and after in Camera Raw. When I press the P key for before and after; CR display the before and after to whole changes that I made and not just to one section. Let say, I am in the Detail section and Just want to see what changes I made in the Detail section only. I used to press the P key, but now I am seeing all the changes that I made to my file. I am using Adobe Photoshop CC and all my software is updated. I appreciatre a fix to this problem with many thanks

Alternatevely you can take advantage of the new function recently introduced in CC. Press "Q" , this will split the monitor in two, (either vertically or horizontally) and each time you go to a new tab and make some change you can go back to previous state by clicking the icon in the bottom right corner (see the picture).
as you can see..you can "toggle between current settings and defaults for the visible panel"

Before and After View

When I'm in my Develop module and I look at some of my edited photos my before and after view is not showing. Sometime I see the original for a second then it resorts to the edited. Now this is happening to some of my collection cause in some collection they are working just fine. Can some explain to me what is happing.
thanks

That's not it. I'm not sure what your talking about or we are talking about two different things. All the files in the collection are before and after are the same this is evident on some other folder in the collection.
I think I figure out the problem
Go to the History located on the left side of your canvas, above the Copy and Paste buttons. You should see Preset, Snapshot, History and Collection. They should have a + beside to expand. Go to History (this is a list of all you edits you made on the image) Go to the bottom where it says import of the file. This is the start point of your file.
Right mouse click on the import xxxx xxxx file ( or how ever you saved your file name). Highlight "Copy History Step Settings to Before."
There you go your good to go
I don't know how to do this on all the images with this problem in the folder all at once. I just do it individually.

Mail Problems before and after 10.4.6

Similar Messages

Maybe you are looking for