Mail - random connections

My mail keeps going off line and gives me a message that there is a problem with port 110. But then it randomly comes back and sends/receives emails. This has been happening very sporadically over the last few weeks, but today it is even worse. The Safari internet connection remains ok throughout. Could I have changed a setting without realising it? Why is it happening randomly? Linda.

Lindart,
Since this is happening on port 110, I am going to assume it is a POP3 account. Do you check this account from any other computer or device? And if so, could that be trying to access the mail account at the same time?
This article was written for iPhone, but applies to any POP3 account being accessed from more than one email program:
http://docs.info.apple.com/article.html?artnum=307009
If you are getting errors similar to those in that article, it could indicate a connection issue, or a large message that is causing your mail client to time out. If Mail reconnects before the server has timed out, the server will see that as two connections, and generate the same kind of errors.
Hope this helps,
Nathan C.

Similar Messages

Mail displaying the message "cannot get mail the connection to the server failed" Help!!!

Hi
Overnight both my hotmail accounts on my Iphone 4s, through Mail, have stopped working and I cannot access my email. Every time I try I get the message "Cannot get Mail. Connection to the Server Failed"
I have rebooted my phone, deleted and readded the accoutns and even reset my network settings to factory seeting but nothing works. A few hours ago it randomly started working again but has since stopped.
Please Help!!!

Contact Microsoft to see if Hotmail is having any issues.
The issue described is not an iPhone or iOS issue.

I'm having strange random connection failures. Are there ineffieciency in my config?

I've been having strange, random connection failures and I'm trying to eliminate possible causes.
What happens is while I'm browsing on the net over wifi, a link will at random not connect to the site, but instead fault to the ISP error page. It happens with highly reliable sites like google, or ebay, or whatever. If I direct connect to the cable modem, the problem site is immediately available.
I'm sitting <6 feet from a 871W router (with antenna). There's one router in my building and others are at my neighbors.
Below is the conf file. Just to imagine how rediculious this problem is, here's a screen shot from a web page. This shows a web page I visited, and after clicking on a link (an embedded youtube video), the error showed up within the page itself.
Why would only some URLs fail to connect? Is there inefficiencies in my config?
    Building configuration...
    Current configuration : 4750 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname TooterTurtle
    boot-start-marker
    boot-end-marker
    logging buffered 51200 warnings
    no logging console
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    clock timezone NewYork -5
    clock summer-time NewYork date Apr 6 2003 2:00 Oct 26 2003 2:00
    dot11 syslog
    dot11 ssid TooterTurtle
       vlan 2
       authentication open
       authentication key-management wpa
       guest-mode
       wpa-psk ascii 0 [my wifi password]
    no ip source-route
    no ip gratuitous-arps
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.10.1 192.168.10.10
    ip dhcp excluded-address 10.0.0.1 10.0.0.10
    ip dhcp pool vlan1
       import all
       network 192.168.10.0 255.255.255.0
       dns-server 192.168.10.1
       default-router 192.168.10.1
       domain-name Ethernet
    ip dhcp pool vlan2
       import all
       network 10.0.0.0 255.255.255.0
       domain-name WiFi
       dns-server 10.0.0.1
       default-router 10.0.0.1
    ip dhcp pool MrWizard
       host 192.168.10.100 255.255.255.0
       hardware-address 0011.0917.66fa
       client-name MrWizard
    ip dhcp pool MasterShake
       host 192.168.10.101 255.255.255.0
       hardware-address 0022.681c.fbcc
       client-name mastershake
    ip auth-proxy max-nodata-conns 3
    ip admission max-nodata-conns 3
    no ip bootp server
    ip domain name mydomain.com
    ip ddns update method ccp_ddns1
     HTTP
      add [zone edit account and url]
      remove [zone edit account and url]
    username admin privilege 15 secret 5 [encrypted secret]
    archive
     log config
      hidekeys
    no ip ftp passive
    ip ssh version 1
    bridge irb
    interface FastEthernet0
     description AdminInterface
    interface FastEthernet1
     description MrWizard
    interface FastEthernet2
     description Belkin
    interface FastEthernet3
    interface FastEthernet4
     description ComcastCableModem
     ip address dhcp
     ip verify unicast source reachable-via rx allow-default 100
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     ip nat outside
     ip virtual-reassembly
     speed auto
     full-duplex
    interface Dot11Radio0
     no ip address
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     encryption vlan 1 mode ciphers tkip
     encryption vlan 2 mode ciphers tkip
     ssid TooterTurtle
     speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
     station-role root
    interface Dot11Radio0.1
     description TootersWiFi
     encapsulation dot1Q 2
     no cdp enable
     bridge-group 2
     bridge-group 2 subscriber-loop-control
     bridge-group 2 spanning-disabled
     bridge-group 2 block-unknown-source
     no bridge-group 2 source-learning
     no bridge-group 2 unicast-flooding
    interface Vlan1
     description EthernetOnly
     no ip address
     no ip redirects
     no ip unreachables
     no ip proxy-arp
     ip nat inside
     ip virtual-reassembly
     bridge-group 1
    interface Vlan2
     description WiFiOnly
     no ip address
     bridge-group 2
    interface BVI1
     description EthernetOnly
     ip address 192.168.10.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly
    interface BVI2
     description WiFiOnly
     ip address 10.0.0.1 255.255.255.0
     ip nat inside
     ip virtual-reassembly
    ip forward-protocol nd
    ip route 0.0.0.0 0.0.0.0 FastEthernet4
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http timeout-policy idle 60 life 86400 requests 10000
    ip dns server
    ip nat inside source list 101 interface FastEthernet4 overload
    ip nat inside source list 102 interface FastEthernet4 overload
    ip nat inside source static tcp 192.168.10.100 80 interface FastEthernet4 80
    ip access-list extended vlan1
     deny   ip 10.0.0.0 0.0.0.255 any
     permit ip any any
    access-list 100 permit udp any any eq bootpc
    access-list 101 permit ip 192.168.10.0 0.0.0.255 any
    access-list 102 permit ip 10.0.0.0 0.0.0.255 any
    no cdp run
    control-plane
    bridge 1 protocol ieee
    bridge 1 route ip
    bridge 2 protocol ieee
    bridge 2 route ip
    line con 0
     no modem enable
    line aux 0
    line vty 0 4
     transport input telnet ssh
     transport output telnet ssh
    scheduler max-task-time 5000
    end

I removed the ip router 0 0 to no great effect, which I consider to be a win.
I'm guessing that since overload is what--I understand--translates the one outside to the many inside IPs, that the suggestion to have only one overload configured means I should combine the two ip ranges into one.
I deleted 10.0.0.0 network. Changed the bridge references to 1 and vlan references to 1. Now wifi and ethernet should all be using the same internal network? That's the idea, right? Any more fat?
[EDITED]
dot11 syslog
dot11 ssid TooterTurtle
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 0 [my passphrase]
no ip source-route
no ip gratuitous-arps
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp pool vlan1
   import all
   network 192.168.10.0 255.255.255.0
   dns-server 192.168.10.1
   default-router 192.168.10.1
   domain-name Ethernet
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
no ip bootp server
ip domain name [my url]
ip ddns update method ccp_ddns1
HTTP
add http:...[zoneedit]
remove http:[zoneedit]
no ip ftp passive
ip ssh version 1
bridge irb
interface FastEthernet0
description AdminInterface
interface FastEthernet1
description MrWizard
interface FastEthernet2
description Belkin
interface FastEthernet3
interface FastEthernet4
description ComcastCableModem
ip address dhcp
ip verify unicast source reachable-via rx allow-default 100
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip virtual-reassembly
speed auto
full-duplex
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encryption vlan 1 mode ciphers tkip
ssid TooterTurtle
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
interface Dot11Radio0.1
description TootersWiFi
encapsulation dot1Q 2
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
description EthernetOnly
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 1
interface BVI1
description EthernetOnly
ip address 192.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list 101 interface FastEthernet4 overload
ip nat inside source static tcp 192.168.10.100 80 interface FastEthernet4 80
ip access-list extended vlan1
permit ip any any
access-list 100 permit udp any any eq bootpc
access-list 101 permit ip 192.168.10.0 0.0.0.255 any
no cdp run
control-plane
bridge 1 protocol ieee
bridge 1 route ip

I keep getting an error pop-up when I try to access my email. The pop-up says Cannot Get Mail The connection to the server failed. I get this pop-up on both my iPhone 5 and my iPad. I can still access my email, but the pop-up is real annoying.

I keep getting an error pop-up when I try to access my email. The pop-up says Cannot Get Mail The connection to the server failed. I get this pop-up on both my iPhone 5 and my iPad. I can still access my email, but the pop-up is real annoying. Can someone please help me with this? -Stu

Hi StuNYC,
Welcome to Apple Support Communities.
It sounds like you're seeing an alert message when opening Mail on your iOS devices. Do you have multiple email accounts setup on the devices? Take a look at the article below, it provides suggestions that will resolve most issues that cause an alert like that to appear in when starting the Mail app.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
I hope this helps.
-Jason

I've set up email on my iPad (talk mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this

I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

I've set up email on my iPad (talktalk.net) and can send and receive mails when connected to my home router and ISP. When connected to a router at another location with a different ISP I can receive mail but not send it. Is there any way round this?

My iphone 5 everytime i go into mail it comes up with - Cannot get Mail - the connection to the server failed- i then have to click ok - I am still receiving mail - it is driving me mad having to click this everytime - anybody else had the same ?

My iphone 5 everytime i go into mail it comes up with - Cannot get Mail - the connection to the server failed- i then have to click ok - I am still receiving mail - it is driving me mad having to click this everytime - anybody else had the same problem and have found a solution - only stated happening since iPhone was updated .

Hello there, Badboymbc.
The following Knowledge Base article provides some steps for troubleshooting mail on your iOS device:
iOS: Troubleshooting Mail
http://support.apple.com/kb/TS3899
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Can't get my mail to connect

Hi, just ran into a problem with my mail today. I've never had a problem with my POP account before. Earlier today I opened up Entourage to take a look at it ( I never use it but was just doing a little exploring). After it opened it gave me a prompt - something about changing the keychains - and I clicked OK. But immediately after this I had problems receiving mail in both Mail and Entourage. First I received this pop-up from Mail:
The POP server “oooooo” rejected the password for user “oooooo”
Please re-enter your password, or cancel.
I re-enter my password and then nothing. After several attempts of this Mail stops connecting to the server.
Anybody know what to do?
Thanks

Hi nipponmark.
Open /Applications/Utilities/Keychain Access, choose Keychain First Aid from the application menu, and proceed to repair the keychain. If that doesn’t work, you may try removing the password entry from the keychain and letting Mail create it again the next time it asks for it.
The fact that Mail appears to be trying to connect to the server on port 0 indicates that there could be something wrong with the network or with your network settings.
Go to Apple Menu > System Preferences > Network, choose Network Port Configurations from the Show popup menu, and make sure that the configuration used to connect to Internet appears at the top of the list. Leave checked (enabled) only the port configuration needed to connect to Internet and Built-in Ethernet (in that order if not the same), uncheck (disable) the rest of network port configurations and see whether that helps — if it doesn’t, turn ON again the ones you want enabled.
Now, from the System Preferences > Network > Show popup menu, choose the network interface used to connect to Internet, go to the Proxies section, and try disabling the SOCKS Proxy if it’s enabled.
Try using a different method to connect to Internet, if possible, or connecting the computer to Internet as directly as possible (i.e. bypassing any routers that might be present, using an ethernet cable instead of wireless, etc.), or shutting down both the computer and the router/modem used to connect to Internet, restarting, and see whether that makes a difference.

Mail server connection problem

Mail in my macbook pro from time to time interrupts mail server connection (mac mini server). As i discoveredn turn off turn on wi fi reestablish connection. Does anybody know how to solve the problem?

Check the server log for details on the local mail server activity. These mail server logs are available via Console.app or via Server.app.
To verify local DNS services — a very common cause of problems — launch Terminal.app and issue the following harmless, diagnostic command:
sudo changeip -checkhostname
You'll need to enter an administrative password for the sudo, might then see a one-time message describing the use of sudo, then some server network configuration information if and as available, and finally an indication that there are no changes required, or that there are DNS or network or other issues.
You'll need to be referencing your local DNS server — you cannot reference your ISP DNS servers, nor any other off-LAN DNS servers here — in your clients. This either by explicit configuration in the clients, or via the DNS server settings distributed by your local DHCP server. Do not reference both local and off-LAN DNS servers, either — just your own local DNS server(s) on your local NAT'd network. No off-LAN off-NAT'd-network DNS servers can provide valid DNS translations for your local LAN, and SMTP traffic is based on properly configured DNS.

Reading Inbox - javax.mail.MessagingException: Connect failed;

I get an error message while trying to read emails by connecting to a company mailbox. The message is as follows:
javax.mail.MessagingException: Connect failed;
nested exception is:
     java.net.ConnectException: Connection refused: no further information
     boolean com.sun.mail.pop3.POP3Store.protocolConnect(java.lang.String, int, java.lang.String, java.lang.String)
     void javax.mail.Service.connect(java.lang.String, int, java.lang.String, java.lang.String)
     void javax.mail.Service.connect(java.lang.String, java.lang.String, java.lang.String)
     void GetMessageExample.main(java.lang.String[])
The code is very simple and as follows:
import java.io.*;
import java.util.Properties;
import javax.mail.*;
import javax.mail.internet.*;
import javax.activation.*;
public class GetMessageExample {
public static void main (String args[]) throws Exception {
String host = "companyname.com";
String username = "user";
String password = "xxxx";
try{
// Create empty properties
Properties props = new Properties();
// Get session
Session session = Session.getInstance(props, null);
// Get the store
Store store = session.getStore("pop3");
store.connect(host, username, password);
// Get folder
Folder folder = store.getFolder("INBOX");
folder.open(Folder.READ_ONLY);
BufferedReader reader = new BufferedReader (
new InputStreamReader(System.in));
// Get directory
Message message[] = folder.getMessages();
for (int i=0, n=message.length; i<n; i++) {
System.out.println(i + ": " + message.getFrom()[0]
+ "\t" + message[i].getSubject());
// Close connection
folder.close(false);
store.close();
} catch (Exception e) {
e.printStackTrace();
I have a two part question:
1. At home I am using a dial-up connection it works when I change the settings to an email account as provided by the local ISP.
I have tried it with both "pop3" and "imap" in
Store store = session.getStore("pop3");
for the company email but it does not work.
Is this a problem with company security? Maybe firewall/proxy error? If so how do I get around it?
2. Also, when I am in the office (LAN used to connect to Internet) I cannot even get a connection to the ISP account - similar problem or different?
Any thoughts and help most appreciated.
Thanks in advance,
Mark

It could be that the mail server is not accepting connections from the machine you are on. Have you tried using Outlook Express or the Netscape email client to connect to the server/account from the machine that is getting the failure?

Javax.mail.MessagingException: Connection refused: connect on localhost

Hello,
I am using Tomcat5.0.28 for a javamail servlet program. I am giving the hostname as localhost. After entering the input details in my html file, i get the error- "javax.mail.MessagingException: Connection refused: connect; nested exception is: java.net.ConnectException: Connection refused: connect " .
can anybody help me regarding in solving error.
Thanks.

First, you're using a very old version of JavaMail. Please upgrade. Some of the properties you're setting aren't supported in that old version.
Second, you don't need the socket factory properties, get rid of them.
Finally, it looks like you're trying to connect on port 143 using SSL. Port 143 is the non-SSL port. That's probably not going to work. Still, it looks like something is refusing to let you connect at all. If you really can telnet from the same machine your program is running on to the same server machine on port 143, then you probably have some sort of firewall that's preventing your program from connecting. Please post the entire debug output if it still fails after correcting the problems above. (Move the setDebug call to before the getStore call.)

I updated to mountain lion and now mail cannot connect to my server

I updated to mountain lion and now mail cannot connect to my server. It says check your user name and password are correct. Well they are, and were. Nothing has changed except the mac OS.
Has anyone else suffered this and knows a way around it? Too annoying to log into my mail every 15mins via a web page anymore.
Efforts tried to resolve this so far:
retyped user name and password, removed account and created a new account, restarted computer, software update, searched forums. so far all have proved unsuccessful.
I have also written to my mail provider and am waiting for feed back from them, but if anyone has any advice it would be gratefully received.
Many thanks,
Mike

Many users upgrading to Mountain Lion have run into this problem, myself included. You likely have corrupted settings for your "Outgoing Mail Server (SMTP)" for each of the failed Accounts. Open Mail>go to Mail's Preferences>Accounts>select an Account in the left column to work on>then set up your Outgoing Mail Server which will INCLUDE resetting up your Password, as its asking you to. Click on "SMTP Outgoing Mail Server" near the bottom of the Accounts window while your mail account is highlighted in the left hand column. When you click on SMTP... you will see a drop down box icon offered at the right side of the line. Click it and then select at the bottom of the the list "Edit SMTP Mail Server". Fill in the required settings for your ISP mail account using their recommended settings.

Since I upgraded to Moutain Lion I'm dealing with wifi problems : no connection or random connection

Since I upgraded to Moutain Lion I'm dealing with wifi problems : no connection or random connection. With OS X Lion wifi was OK.

So, Darrall, it seems to be fixed. Mind you, this has happened through a seemingly unrelated, but hopefully replicable sequence of events. You be the judge.
I went to my other login account, which as it happens is also an admin account. Voila, the secondary click worked fine. So I returned to my primary account, where I did the following:
First, I unpaired the trackpad. then I remembered I needed something to move the mouse with, so I re-paired the magic mouse I'd had before. I thought I'd turned off the trackpad, but apparently not, so the computer re-paired it automatically. None of this had any immediate effect, as you'd imagine.
Then I went to Mission Control in Preferences. There, I deselected "Show dashboard as a space", and in the hotcorners, I deselected Mission Control from the bottom left, where it had been. I didn't replace it.
Now, my secondary click works. Uh huh. I was suspicious that it might have more to do with Mission Control and/or Dashboard than the trackpad, only because I'd beaten that horse till my arm hurt and this was all I could think of.
Never did I imagine this would get fixed short of creating a new login account and somehow copying everything - since I didn't know what was wrong, I could easily have copied the error too - so I'm very pleased and relieved. If you haven't fixed yours yet, try this. Let me know what happens!

Setup Database mail that connect with tcp/ip to the instance

I want to setup database mail that connect to the named instance via a fixed TCP/IP port.
This is a named instance that works with a fixed TCP/IP port
Database mail works fine if shared memory is enabled.
If it is disable I get the following log entry in the application log.
Log Name: Application
Source: DatabaseMail
Date: 18/11/2014 20:56:05
Event ID: 0
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: Server.dom.be
Description:
1) Exception Information
===================
Exception Type: Microsoft.SqlServer.Management.SqlIMail.Server.Common.BaseException
Message: There was an error on the connection. Reason: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL
Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified), connection parameters: Server Name: server\instance, Database Name: msdb
Data: System.Collections.ListDictionaryInternal
TargetSite: Void OpenConnection(Microsoft.SqlServer.Management.Common.SqlConnectionInfo)
HelpLink: NULL
Source: DatabaseMailEngine
StackTrace Information
===================
at Microsoft.SqlServer.Management.SqlIMail.Server.DataAccess.ConnectionManager.OpenConnection(SqlConnectionInfo connectionInfo)
at Microsoft.SqlServer.Management.SqlIMail.Server.DataAccess.DataAccessAdapter.OpenConnection(String dbServerName, String dbName, String userName, String password, String appName, Int32 connectionTimeout)
at Microsoft.SqlServer.Management.SqlIMail.Server.DataAccess.DataAccessAdapter.OpenConnection(String dbServerName, String dbName, String userName, String password, Int32 connectionTimeout)
at Microsoft.SqlServer.Management.SqlIMail.IMailProcess.QueueItemProcesser.ProcessQueueItems(String dbName, String dbServerName, Int32 lifetimeMinimumSec, LogLevel loggingLevel, Byte[] encryptionKey, Int32 connectionTimeout)
Is there a way to change the connection parameters?
PS the Browser Service is not running

Hello,
If the instance is a named instance, then SQL Server Browser service should be started to be able to connect to the instance
using TCP/IP.
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com

Java Mail throws Connect failed error in Oracle 11g Enterprise Edition

Hi,
I am using Oracle 11g Enterprise edition.I have a java class which is used for reading outlook 2010 inbox and download attachments from mails .For Connecting to OutLook from oracle i am using "POP3S" protocol in my java class. Which is working fine until my database is oracle-11g standard edition. Last week we are upgraded our database from oracle 11g standard edition to oracle 11g enterprise edition after that i can't connect to mail server through my java class which throws an error as follows.
DEBUG: setDebug: JavaMail version 1.4.4
DEBUG: getProvider() returning javax.mail.Provider[STORE,pop3s,com.sun.mail.pop3.POP3SSLStore,Sun Microsystems, Inc]
DEBUG POP3: mail.pop3s.rsetbeforequit: false
DEBUG POP3: mail.pop3s.disabletop: false
DEBUG POP3: mail.pop3s.forgettopheaders: false
DEBUG POP3: mail.pop3s.cachewriteto: false
DEBUG POP3: mail.pop3s.filecache.enable: false
DEBUG POP3: mail.pop3s.keepmessagecontent: false
DEBUG POP3: mail.pop3s.starttls.enable: true
DEBUG POP3: mail.pop3s.starttls.required: false
DEBUG POP3: mail.pop3s.apop.enable: false
DEBUG POP3: mail.pop3s.disablecapa: false
DEBUG POP3: connecting to host "194.42.133.180", port 110, isSSL true
javax.mail.MessagingException: Connect failed;
nested exception is:
     javax.net.ssl.SSLException: Unrecognized SSL message, plaintext connection?
     at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:210)
     at javax.mail.Service.connect(Service.java:295)
     at javax.mail.Service.connect(Service.java:176)
     at GetNoonReport.Connect2Mailserver(GetNoonReport:338)
     at GetNoonReport.ReadMail(GetNoonReport:103)
Caused by: javax.net.ssl.SSLException: Unrecognized SSL message, plaintext connection?
     at com.sun.net.ssl.internal.ssl.InputRecord.handleUnknownRecord(InputRecord.java:501)
     at com.sun.net.ssl.internal.ssl.InputRecord.read(InputRecord.java)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.readRecord(SSLSocketImpl.java)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.performInitialHandshake(SSLSocketImpl.java:1025)
     at com.sun.net.ssl.internal.ssl.SSLSocketImpl.startHandshake(SSLSocketImpl.java:1038)
     at com.sun.mail.util.SocketFetcher.configureSSLSocket(SocketFetcher.java:507)
     at com.sun.mail.util.SocketFetcher.getSocket(SocketFetcher.java:238)
     at com.sun.mail.pop3.Protocol.<init>(Protocol.java:107)
     at com.sun.mail.pop3.POP3Store.getPort(POP3Store.java:261)
     at com.sun.mail.pop3.POP3Store.protocolConnect(POP3Store.java:206)
     ... 4 more
Is Oracle Enterprise Edition supports "POP3S" protocol?, Or Enterprise edition needs any additional configuration for establishing outlook connection with "pop3s" ?.
Any help is appreciated
Regards ,
Nisanth

907833 wrote:
Hi,
I am using Oracle 11g Enterprise edition.I have a java class which is used for reading outlook 2010 inbox and download attachments from mails .For Connecting to OutLook from oracle i am using "POP3S" protocol in my java class. Which is working fine until my database is oracle-11g standard edition. Last week we are upgraded our database from oracle 11g standard edition to oracle 11g enterprise edition after that i can't connect to mail server through my java class which throws an error as follows.
I suspect root cause is with Java not Oracle.
Oracle RDBMS does NOT speak any "protocol" except SQL natively.

On my hotmail email, a sign comes up saying *cannot get mail* the connection to the server failed

i have a new itouch and have hotmail as my email account, today 21stn july 2012, when i went onto my mail account, a sign saying the following
cannot get mail the connection to the server failed, what do i do now as i am not receiving any emails and my junk box is missing ?

Hi kristafromne!
I have an article here that I believe will help you with this issue. This article is about troubleshooting email accounts on your iPhone and can be found here:
iOS: Unable to send or receive email
http://support.apple.com/kb/ts3899
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Mail - random connections

Similar Messages

Maybe you are looking for