Mainboard PM8M-V cannot boot from SATA

Mainboard PM8M-V does not have BOOT FROM SATA in the BIOS settings. In fact nowhere in the entire bios SATA is mentioned.
The SATA HDD is properly partitioned. Windows is installed on it, but it boots from an IDE HDD and then continues to load from the SATA.
I tried to set the bios to boot from SCSI, but in vain.
I checked if there is a bios update, but the MSI website linked me to Live Update 5, which even cannot find drivers for the mainboard, not to speak for a bios update.
The version of the BIOS is
Manufacturer : Phoenix Technologies, LTD
Version : 6.00 PG
Date : 03/23/2005 (mm/dd/yyyy)
HELP!

The boot options are:
Floppy, LS120, IDE0,SCSI,CDROM,IDE1,IDE2,IDE3,ZIP100,USB-FDD,USB-CDROM,USB-HDD,LAN,DISABLED
I tried to remove the IDE HDD (also no USB drives were connected) while installing windows, it won't boot anyway.
Even if windows did not write correctly the MBR (well, I used the repair console to with FIXMBR and FIXBOOT), the BIOS should probably say something like "No boot sector", but it just hangs.
After that I installed with an IDE HDD connected.
Presuming that "as i recall boards of yours age listed all drives as ide" is true, shouldn't I have IDE5, since there are 4 IDE channels anyway? I will try all the IDE options, anyway.
I did not understand this question "is the make and size of the sata in that list"?
Quote from: Henry on 06-July-12, 07:31:06
It should ID the drive by model number or at least by brand & size as Wonkanoby said, at least it does on newer MBs.
Some options of the device are shown during boot (some RAID adjustments), but it is not displayed anywhere in the BIOS setup.
Also, on most bioses during oot a message is displayed "Press key XXX for boot options", but this one does not display something like this. Any clue if there could be such a key? F1 and F8 do not work.

Similar Messages

[VIA] Cannot Boot From SATA PCI Controller With On Board RAID Enabled

Hi.
I have a KT3 ULTRA 2 with onboard RAID controller. I have installed a SUNIX 2 port SATA PCI Controller which works perfectly & appears in the selectable boot devices. This is not a problem except for the fact that I have 4 devices on the On-Board Raid Controller. When the on-board raid controller is enabled, the SATA device dissapears from the boot options & I can no longer boot from the SATA controller.
Any help is greatly appreciated.
Many Thanks

I had already tried that....
I set the boot sequence to use the SATA card & then renabled the on-board raid, but after reboot the sata card is not available as a possible boot device & asks me to insert system disk...even if the boot sequence is set to boot from other devices.
Really annoyying this, looks like I am going to have to get a different motherboard for something so silly. I am already at the latest bios release.

Help: Cannot boot from leopard disc anymore, everything else fine

I was working on an ibook and messing with it in firewire mode and was going to install leopard on it that way from my macpro. (just letting you know the context)
I tried to restart my machine(mac pro) and boot leopard both by pushing C and by running the installer.
I get the "You need to hold the power button panic message" everytime I do this. I unplugged external devices and tried this also and it has the same problem.
I cannot boot from the dvd anymore. If I eject the disc, osx loads normally.
Any ideas what I can do? (I have tried safe boot, pram clearing and hold option on boot to check options)
Here is the kernel panic when it finally loads into osx.
here is the kernel panic log when it reboots into OSX
Sat May 17 14:13:09 2008
panic(cpu 1 caller 0x001A7BED): Kernel trap at 0x894ec373, type 14=page fault, registers:
CR0: 0x8001003b, CR2: 0x00000018, CR3: 0x00df8000, CR4: 0x00000660
EAX: 0x00000000, EBX: 0x00000000, ECX: 0x00000000, EDX: 0x0a5a1004
CR2: 0x00000018, EBP: 0x817c3bc8, ESI: 0x0a4c5c00, EDI: 0x0a4c5c00
EFL: 0x00010246, EIP: 0x894ec373, CS: 0x00000008, DS: 0x0a3c0010
Error code: 0x00000000
Backtrace, Format - Frame : Return Address (4 potential args on stack)
0x817c39d8 : 0x12b0e1 (0x4555b4 0x817c3a0c 0x133238 0x0)
0x817c3a28 : 0x1a7bed (0x45e568 0x894ec373 0xe 0x45dd24)
0x817c3b08 : 0x19e517 (0x817c3b20 0xa83c980 0x817c3bc8 0x894ec373)
0x817c3b18 : 0x894ec373 (0xe 0x48 0x10 0x10)
0x817c3bc8 : 0x894db540 (0x0 0xa83c980 0xa4c5c00 0x1)
0x817c3c08 : 0x78d45139 (0xa4c5c00 0x1 0x0 0x13)
0x817c3c68 : 0x78d3e940 (0xa4c5c00 0x2407 0x817c3d2c 0xa4c5c00)
0x817c3c98 : 0x40c515 (0xa4c5c00 0xacd8130 0xacd8130 0x0)
0x817c3ce8 : 0x437535 (0xa4c5c00 0xacd8130 0xacd8130 0x0)
0x817c3d48 : 0x18c8aa (0xa4c5c00 0xacd8130 0x0 0x0)
0x817c3db8 : 0x12d165 (0xa525c78 0xaa76b90 0x817c3df8 0x11ee04)
0x817c3df8 : 0x126247 (0xa525c00 0xa2f9254 0xaad84b0 0x0)
0x817c3f08 : 0x196afc (0x817c3f44 0x0 0x0 0x0)
0x817c3fc8 : 0x19eb34 (0xab382a0 0x0 0x1a10b5 0xa63f208)
No mapping exists for frame pointer
Backtrace terminated-invalid frame pointer 0xbffff378
Kernel loadable modules in backtrace (with dependencies):
com.apple.NVDAResman(5.1.6)@0x894d8000->0x89704fff
dependency: com.apple.iokit.IONDRVSupport(1.5)@0x78cc5000
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x78ac0000
dependency: com.apple.iokit.IOGraphicsFamily(1.5)@0x78d36000
com.apple.iokit.IOGraphicsFamily(1.5)@0x78d36000->0x78d51fff
dependency: com.apple.iokit.IOPCIFamily(2.4)@0x78ac0000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
9A581
Kernel version:
Darwin Kernel Version 9.0.0: Tue Oct 9 21:35:55 PDT 2007; root:xnu-1228~1/RELEASE_I386
System model name: MacPro1,1 (Mac-F4208DC8)

I really appreciate everyone's help.
I am certainly not above taking the machine in but I will say this.....
I have been building and working on PC's for 15-20 years. I have never once used or had the need for a repair shop. It is my hobby. I recently switched to osx to give the mac a try and I love it.
I will say that vista/xp has four times as many problems but at least i can fix whatever comes my way hardware or software.
Any more ideas how to settle this without making my first trip to the repair shop ever?...
Chad

Cannot boot from osx or cd, help

Hi,
I have a problem. My macbook 5.1 boots only to windows, not to cd or osx. I am not sure what has happened but I think I installed the latest security update. I have a backup with time machine (osx) and vista with windows backup. I can wipe the whole disk clean (I do this only if I am absolutely sure it will work, CD is now unresponsive, what about if network fails...).
However, I cannot boot from CD, to verbose mode or to single user mode. None of the keys work (eject, c, s, v, cmd+c, cmd+v, cmd+s) anymore at startup. My installation dvd is stuck into the cd-rom. The eject button does not work in windows (otherwise the vista works perfectly). Also the refit screen has disappeared.
This problem is caused (to my knowlege) due to following actions:
1. security updade => failure to boot osx (hangs to apple-logo and shuts down)
2. recovery from time machine to 2 days old configuration (last known working)
3. current status, no cd, osx or startup buttons
This is my work computer and I need the linux (osx) part on monday. Please help.
Juha
Technical details:
- refit
- osx leopard
- macbook 5.1
- vista created with bootcamp
- timemachine 500Gb

I got the problem worked out. Now that I have the possibility to boot from cd I used the recovery from timecapsule again. Now it worked more properly. There is some issues with some programs and data (missing), but thats another story.
Last time I left the recovery program calculating the space needed (step 1) overnight, as takes a lot of time. I finished the step 2 (choose recovery date and copy the files) in the morning. I was not at the computer when it did the thing and I only saw the text 'recovery complete'.
Apparently there is a 'feature' that if you lose the connection between steps 1 and 2, the recovery program copies the network path that is empty (connection lost -> empty path). The program thinks everything is copied and gives 'recovery complete' message.
The problem is now mostly solved, some programs are not recovered. This is seen as question mark icons in the tray. Overall I have succesfully recovered from the latest security update.
Juha
P.S. My original login name has disappeared from this forum. I am the same guy as Dv3. Could some admin mark this as solved.
Message was edited by: dve_

I cannot boot from HDD nor CD/DVD drive - Satellite C

I want to recover my laptop & i need to boot from cd.
I pressed F12 first time & boot from cd but i discoverd that i have put another cd just when i restarted (correctly) i could not boot from cd neither hdd.
When i log in bios hdd was detected but not available in boot priority menu. Just network adapter was there & now i cannot boot from hdd nither cd/dvd. Bios version is 1.30
PLEASE HELP ME

> When i log in bios hdd was detected but not available in boot priority menu. Just network adapter was there & now i cannot boot from hdd nither cd/dvd.
Does this means that neither HDD nor CD/DVD drive appears in the BIOS boot option?
Strange what notebook model do you have?
Did you try to set BIOS to default?
If not do this (press F9 and save the changes in BIOS)

Win 7 pro installed on hp touchsmart 320-1030, the machine cannot boot from installation DVD. Assist

I have installed Win 7 professional on hp touchsmart 320-1030 with an OEM DVD to overwrite Win 7 premium preinstalled from factory.
I want to reboot the machine with the same DVD after completing the installation, to test for possibility of reimage in case of crash. Although in bios, I specify cd\dvd as firts boot media, the machine cannot boot from installation DVD. I have 20 machines that behave this way. Can anyone assist?
Note: I had to delete all partitions on the PC before doing a fresh installation of Win 7 pro as Premium can not joing domain.

Hello,
So, you installed Window 7 Pro with a DVD, you boot with it to install the O.S, and now it does not work?
Have you tried to load the BIOS default values or even updating the BIOS?
If it had work before, cant understand why it does not work now...
Let me know.
Thanks,
I work for HP! Please remember to provide and if this helped click ON

Cannot boot from DVD since 10.4.6 update.

My Quad cannot boot from the Superdrive at all.Upon updating I decided to repair permissions from the DVD but everytime I got to the Apple logo the fans powered up,full tilt. I had to turn the Quad off from the power button and start up holding down the mouse, in order to eject the DVD.
As far as I remember, I allowed the computer to start up twice, and disconnected all peripherals whilst updating.
I've tried zapping the pram and resetting the nvram to no avail.I've inserted Disk Warrior and that will not boot. The computer runs fine from the HD (although there was one occasion when, briefly, a small OS9-style Mac monitor appeared with a question mark, then made way for a proper boot), but I'm really concerned at this problem. I do not want to wipe the system drive and start from scratch,since I've only just finished migrating a whole buch of software from another G5, and I have TV job looming.
Incidentally, both my other G5's and Mac Mini updated with no perceptable problems. Can anyone shed any light on this and, perhaps, offer a solution (other than a wipe ! ).
Thank you.
G5 Quad 2.5,G5's DP 2.5/2.0,Mac Mini Mac OS X (10.4.5) MOTU 2408's Mk3x3,24i/o,Hammerfall HDSP 9652x3

Any installation can theoretically cause harm. If you aren't backed up, you may be forced to use Target Disk Mode if you can't boot a DVD, or an external DVD burner that supports booting. Both LaCie and Otherworld Computing have external Firewire DVD drives that support booting. Target Disk Mode is described here:
http://docs.info.apple.com/article.html?artnum=58583
Fortunately when you boot via Firewire or use Target Disk Mode, you bypass the hard drive's bootloading software, which you don't when you use the internal optical drive.

K7N2G-ILSR: How to boot from SATA when a raid card is installed

The situation:
1. I have a separate raid controller (Silicon chip) with 2 drives on raid 0.
2. I have another drive (my boot drive) that I want to place on the onboard Promise SATA raid controller.
The problem:
The bios doesn't include an option to specifically boot from SATA, only SCSI. So when I place my boot drive to the onboard Promise SATA raid controller, the system won't boot because it's looking for system files on the raid 0 drive.
Is there a workaround for this?

Well, all my drives are IDE. I did try the SATA RAID using lumberjacker's bios but it isn't stable.
Aside from 3 IDE drives, I also have 2 atapi drives (cdr-w, dvd).
Here's my current setup:
ide 0 - boot drive (master), DVD (slave)
ide 1 - cdr-w (master)
onboard ide (sata controller) - (vacant)
SATA 1 - (vacant)
SATA 2 - (vacant)
promise raid card (2 ide ports)- 2 hard drives on raid 0 (both as master)
What I really want to do is place my boot drive on the SATA port (using a pata to sata converter), or on the onboard promise parallel port. So that it can have it's own port.

Wich Sun machines can boot from SATA disk?

Hi,
I would like to know which (newer and older) Sun machines can boot from SATA disks.
I think this is a feature of the OBP - so the question is:
Are there any updated OBPs for older Sun machines to boot from SATA disks?
TIA
Bernd

Hi,
I am aware the limit with earlier openboot revisions that limit ATA drive size to +130GB>>( search the forum for previous threads on this topic ), I recommend using only
supported drives in Sun SPARC systems. What kind of project are you working on? That's my private test environment. Due to my limited budget I use only older machines there (for example, U10, U30, etc). I was thinking about buying a used V120 or something like that to replace my existing fileserver.
A V120 with two internal 500 GB harddisks would be perfect for that .
Looks like I've to wait until used T1000 are available to a reasonable price.
regards
Bernd

Satellite U925t cannot boot from USB

Hi
I cannot boot from USB flash drive on Satellite U925t. I use bootable USB flash drive inserted (Hiren Boot 15.2, sure booted on another laptop), restart the system. When the splash screen is displayed, press F12 to access the boot menu, selecting USB - but laptop no boot from USB.
Please, Help me.
Thank you very much

From within Windows, try holding SHIFT when you select Shut down. Is there any change then?
Also, try entering the UEFI settings, disabling Secure Boot, and changing UEFI to CSM.
- Peter

Can i try archlinux on usb if my pc cannot boot from usb?

it seems my old pc cannot boot from usb, only boot from hd or cd.
can i use usb? or i have to burn a cd?

If you have a floppy disk you can put the PLoP bootmanager on it:
http://www.plop.at/en/bootmanagerdl.html
This bootmanager has USB support and can boot from an usb stick even though your bios does not support it.
You can also burn PLoP on a CD. This is good if you want to burn only one generic CD and then be able to boot any usb stick instead of burning one cd for each OS you want to boot.

IdeaCenter A310, Cannot boot from CD – Code 5

Installed a developers/trial version of Windows 8 on my A310, only it appears to have somehow completely removed my recovery partition.
Now I have no working OS on the computer and when I attempt to boot with a Windows 7 CD to reinstall I get a 'Cannot boot from CD – Code 5' error.
Why won't it boot from the CD? How can I reinstall Windows? Pleaseee help.

Hi ToxicVoices and welcome to the forum,
If you hit F12 at the bios splash screen, it should bring up a list of bootable devices. Does the cd drive show up there?
If you hit F11, it should take you into the recovery environment if the recovery partition is still there. If the recovery is still there, you should be able to restore from a backup up, (if you made a backup). If no backup, you would have to restore to factory settings.
Dave
T430u, x301, x200T, x61T, x61, x32, x41T, x40, U160, ThinkPad Tablet 1838-22R, Z500 touch, Yoga Tab 2 Windows 8.1, Yoga Tablet 3 Pro
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
If someone helped you today, pay it forward. Help Someone Else!
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

CDBOOT: Cannot boot from CD - Code: 5

When I attempt to boot from my Windows 7 install disc, I get this message on a black background:
CDBOOT: Cannot boot from CD - Code: 5
I'm using a late-2008 13-inch aluminum MacBook running OS X 10.7.
I've attempted burning the install .iso file multiple times (creating a couple of useless DVDs) at the slowest speed possible (which seems to be 2.4x, according to Disk Utility), and that has not solved the problem.
I haven't been able to find any help on this issue for a Mac user who doesn't already have Windows installed. (There seem to be solutions for people who are already running Windows).
Can anyone help?

Hi,
I had the verry same problem and I did multiple things I thought that could fix this problem.
Point one, the burning speed has nothing to do with the quality of your boot disk, you only have to lower burning speed if your burning process fails. So remind this for future burning problems.
1: I did the Lion software update.
2: I got another .iso file, burnd it and made a new partition in bootcamp and ran the setup again.
This time it worked really fine. But I'm not shure wether it was the SU or the new .iso... I checked the SU summary for the lion system update, but there was nothing to find on a boot camp bug and since they've improved boot camp it should work better
I have a 27" imac with the 2TB drive and Solid state so I was thinking that maybe it depended on which fysical drive I made the firtual bootcamp drive. But I tested the new W7 Boot disk on both fysical drives and it worked on both.
UPDATE: I found the reason... I compared the two copies of windows 7 boot disks and the one that works had a different name... Your boot disk should be called "CD_ROM" if not, the bootsequence will not recognize your DVD as a CD which appears to be nescesary for the installation process.
Sorry for the incomplete english, I'm from Belgium.
Message was edited by: Lonely Alien

My Mac can't get passed gray screen, and I cannot boot from cd. Help!

My Mac can't get passed gray screen, and I cannot boot from cd. Help!

Grey Screen
https://support.apple.com/kb/TS2570
https://discussions.apple.com/message/16276201#16276201

Help diagnos. flashing question mark on monitor, cannot boot from CD drive

Any ideas? This is an older G3 tower which was "souped Up" wtih USB and Firewire cards, memory
Mac froze in midst of work last week. Now only get flashing question mark supermimposed on image of a floppy drive.
Tried to re install system (OS9) but cannot get ANY CD to boot from CD drive. I reboot, hold down "C" Key with CD in tray ( and i can hear the CD drive working). But the tray opens and ejects/rejects the CD).
I now suspect the problem is NOT the OS but rather a hardware issue.
Am I correct in this assumption? what else could this be?
I am trying to help an older gentleman who has no backups and has some important documents on the HD.If I can boot up, might be able to retrieve those itesm. (and get a newer Mac!)

Not the answer,Dale (thanks anyway)
I read that article.
I cannot boot from any bootable CD.
Inserted the OS install disk as well as third party bootable CD.
with CD in the CD drive tray, I restarted and held down the C key.
Mac restarted but the CD tray popped open. Would not boot from the CD.
That is why I posted query
not only do we have the flashing question mark but bootable CDs are not booting this Mac. So I can do no diagnostics, no repair, not salvage of files.
I am trying to understand where the problem lies. am guessing Hard Drive failure but why should CD also not work?

Mainboard PM8M-V cannot boot from SATA

Similar Messages

Maybe you are looking for