Maint.Work Center -Length of Break Hours-Reg

Dear PM Guys,
I want to specify the exact timing of Break in Maint.Work Center.Eg
Start time-08.00.00
Finish time 17:00:00
Length of Break:01:30:00
My requirement is I want to specify the 11/2 hours break timing as
12:00:00-13:00:00(1 hr) and 15:00:00-15:30:00.
Where to specify this in work center.

Dear
Pls process the ur req as below
IR02--Cap. tab- Cap Header---
Here u can find shifts, breaks, cap profile, HR assignment.
But using this ensure that shift created at OP4A t codes before doing the above.
our friend is given I/p it will helps you , if its ok close the thread . unless log ur query
Thenna

Similar Messages

Maint. work center

Hi All,
In which report i could see the work done (Hrs) by the maint. work center in whole month?
regards
sunil

Dear,
U can get the total actual work done by that workcenter through IW47. In the transaction u can select Actual work, actual duration, actual start and actual finish etc...
U can get the total actual work done duration for the given period.
Regards
Srinivas

Overload in work center

Hi,
The scenario is like this..
My work center capacity is 10 hours per day.I use the overload field in worcenter & give the percentage as 150 % & my requirement for that particular day is 12 hours. But if i go & see in CM01 & see available capacity it still shows the same capacity & shows that my work center is overloaded ( capacity for that day it still shows in red colour).
I want to know that if i give overload percentage in workcenter wheather it will be reflected in CM01 when i go & see the capacity evaluation for that workcenter.Do i need to do any settings in SPRO for it..
regards
SAP-PP

Hi Ashish,
Your requirement is to use that particular work center for 4 more hours on that particular.If you are try to change the overload % it will be applicable on all the days.
Instead you can try by increasing the no. of working hours in the shifts & intervals tab for that particular day.
To do this choose capacity tab & then go to shifts & intervals.
Here add an interval Eg: 25/05/07, work hours is 06.00 to 18.30 hours,with 0.30 min break.
Regards,
Senthilkumar SD

Any function to calculate actual work hours (deduct the break hours)

Hi expert,
I have defined the daily work schedule & break schedule. Work center is assigned with the daily work schedule. Now I want to calculate each work center actual work hours. I have a table where the start & finish time of working is keep.
for eg.
first break hr 10:00am to 10:15am
second break hr 13:00pm to 14:00pm
The work center might start work from 10:05 and finished at 14:30 or any other case.
I need to deduct the break hrs & get the actual hr worked
Is there any function to calculate the actual work hours base on the daily work schedule & break schedule ?
Thanks

Hello,
Try the below FM's
HR_PERSONAL_WORK_SCHEDULE
WORKING_HOURS = 'X' " you will get the actual work hours
HR_BE_WORKING_SCHEDULE
Try the below class
CL_PT_TIME_EV_WORK_SCHED_UTIL
Regards,
Krishna
Message was edited by:
Krishnakumar

Actual hours done against a work order for a Work Center by non-maintenance

Hi All,
I have below question with respect to work center.
-If there is this actual work hours done on a work order by non- maintenance personnel for a certain work center and same is not reflecting under operation tab of work order, then where & how this hours (done by non- maintenance personnel) for a work order is maintained for that work center?.
-In which database table these hours done by non- maintenance personnel for a work order is stored by work center wise.?
Thanks

Have a look at the document flow button in the order header.
The confirmation data resides in table AFRU
PeteA

Standard Hours Required on a Work Center for a month along with CC

HI Gurus,
My requirement is :
I need a report which fetches how many hours are required in a month on a particular cost center attached to work center for a plant.
Is there any standard report to fetch this . If no how can we develop a report. Which tables we need to combine in CO and PP.

Hi,
Check report S_ALR_8703611.
Regards.

Report for work center hours , maintenance order wise for SAP 3.1i version.

Hi Team,
We are using older version of SAP, that is SAP 3.1i. Here we don't have any transaction code such as IW47. Is there any other way to get report of work center and work center hours-order wise.
Please respond.
Regards,
Kiran

Have a look at table AFRU
PeteA

Work center deletion -reg

Hi,
Can you put deletion flag for a work center ?
or is the only option is go to CR02 and delete ?
Once we delete then latter any thing to revert of trace means what to do ?
is it possible to put deletion flag for a work center and revoke when required again ?
please help
regards,
madhu kiran

Hi,
The question is while deleting the work center , system will not allow to delete unless its taken out from all the routings where ever it is assigned .
But when i put deletion flag its not stopping instead its proceeding further and just setting the deletion flag for the work center
issue is when the work center is in use in routings system should not allow to put deletion flag
once i put deletion flag system should not allow to use the same work center in any of teh routings
but system is allowing both
only at the time of standard cost run we can get an error saying that working center is set deletion flag
instead when i try to set the deletion flag itself ca system prompt and stop me doing that and when i set it should stop me using the work center set for deletion in any routings further
what should be done ?
regards,
madhu kiran

Reg: Combined work center / Capacity requirement planning .

Hi,
i need few informations regarding work center.
1. Can we create Resource (for process industry) similar to that as Work center which we create for (discreate industry)
can i use the workcenters (CR01) instead of Resource(CRC1) to my master recipe. is there any impact by using workcenter instead of resource to master recipe..?
2 In foundry we are using some Iron Plates for resting of Moulds. And these Plates we are having in limited numbers in Foundry.
Arond 30 Now i want to create a resource for this..? How to consider this Plates for resource..? Whether M/C or what..?
We are planning to carry out Proper scheduling and capacity planning for this resource.
3. And May i know how to carry out Proper scheduling and capacity planning of resource.. So if capacity is not available ,i should be not able to go-head even with the releasing of order. How to carry out this. Is any customization required.
4. Can we create combined resource Ex: Crane and laddle.
I need to create these two resource has single resource ..is it possible..? may i know how the costs/ time to capture.?
Please let me know.......THANK U IN ADVANCE.
Edited by: dan01234 on Dec 30, 2010 6:21 AM

Dear
Frist of all , I would appreacite if you can create seperate theard as you have multiple question .Refer : http://wiki.sdn.sap.com/wiki/display/HOME/RulesofEngagement
However , please find the answers :
1.. Can we create Resource (for process industry) similar to that as Work center which we create for (discreate industry)
can i use the workcenters (CR01) instead of Resource(CRC1) to my master recipe. is there any impact by using workcenter instead of resource to master recipe..?
Yes you can with Usage Type 009.But there may be diffienece in Standard Value Key and Formula Key which will be used for calcuating activity and also Capacity Reuiqemenet .
.2 In foundry we are using some Iron Plates for resting of Moulds. And these Plates we are having in limited numbers in Foundry.Arond 30 Now i want to create a resource for this..? How to consider this Plates for resource..? Whether M/C or what..? We are planning to carry out Proper scheduling and capacity planning for this resource.
A resource is plance where certain operation will happend sequentially as per Master Recipe or Routing .If you have Plate where you carry our certain engineering optiaon rather utlising thoem at requorce to excute the opration , then you can very well create them as resource or work centre .This Resource /Work centre will be having optaion , material , scheuling , CRP etc .Do u think that u will doing the same for Plate ??
If you are interested to carry out CRP/Scheduling the refer this theard : Capacity Leveling of Work Center
4. Can we create combined resource Ex: Crane and laddle.I need to create these two resource has single resource ..is it possible..? may i know how the costs/ time to capture.? :
Yes you can if both of them are intregal part of the resource /work centre as per as Setup , Machine , labour hrs is concern based on selection of Standard value Key and Formula Key .Wor centre or Reosurce cost captured through Actvity type ( KP26 with fixed or variable rate aginst costing elenemts) and Formula Key as assinged in the reosurce or work centre -Costing tab .
Check and revert
Regards
JH

Formulas in work center-reg

Hi,
I have few quires on the subject cited .
in the define formula parameters for work centers i have found the and i could not understand the meaning and usage
especially of SAP_11 operation splits , what they mean ?
SAP_09     Operation quantity
SAP_10     Other formula
SAP_11     Operation splits
once we define work centers formulas with these formula parameters how these work ? when standard cost is run for the part number how it takes these defined formulas in to consideration to give the manufacturing cost
please provide some thoughts on these work center formula parameters and formulas and usage
regards,
madhu Kiran

Hi jagadeesh ,
thanks for your details
my doubts are why we define these ? for the purpose of standard cost ?
any way when we run standard cost for the part number , based on the times mentioned in routing it will calculate the cost ?
or is it like this
standard values like handling time , machine time etc.. if we can not enter for an operation ,then for the calculation of these we
define work center formulas and through this system picks the handling and machine times while calculating the standard cost
is this thinking correct ? might be wrong alos , pl let me know
i am really not clear with these work center formulas and their usage
1. for example in our system for a work center the formula defined as
ZPT100 --Cost - Painting & Laquering
formula = ( PITCH CONSTANT * Operation quantity ) / ( JIG DENSITY * Conveyor Speed )
this is defined for the standard value Jig density used in painting
2. for handling time the below formula is defined
ZMG001------COST - Handlng Time
formula = HANDLING TIME * Operation quantity / Base quantity / Operation splits
3. What is the difference between base quantity and operation quanity ?
   is it that base quantity is for the quantity with reference to which we are creating routing ?
operation quantity is the out put of that operation ?
if so operation quantity and all where we mention in routing ? i understand if we wrok on discrete we create routing with base quantity 1 and based on the order quantity , it will become the operation qty
but we work on REm
how to go about ?
can you please thorw ur thoughts on this ?
regards,
madhu Kiran
Edited by: madhu kiran on Sep 18, 2009 1:29 PM

How to assign Asset number to PP work center -reg

Hi,
When we create PP Work center through CR01 can we assign the asset number ?
or while creating asset number through AS01 can we assign the PP Work center ?
Our major issue is
FI : ASSET
PM:Equipment
PP: Workcenter
we are not able to link . we need to have same cost center for all the three . but as of now we dont have the link for the three and what ever cost centers we assignsystem is accepting
how to solve this ?
i could not find any fields in work center either to assign asset or equipment ?
only in equipment i can give PP work center but how it links all the three Asset , Equipment and Work center ?
regards,
madhu kiran.

HI
In euipment you can assign the PP work center and from the asset AS02/AS03 go to environment > additional amster data > you can get the cost center assigned to asset fro this you can relate the cost center to all three.
Hope it will help u
Rgds
Anupam Sharma

Work Center (No. of indiv. cap)

Hi,
I have Assembly Work center for details are as follows,
Start                         06:30:00
Finish                       23:30:00          Capacity utilization 100
Length of breaks     01:00:00           No. of indiv. cap.   2
Operating time          16.00             Capacity             32.00        H
Here available capacity is shown as 16 Hours.
But in actual there are two shift 06.30 to 15.00 with 1 person and second 15.00 to 23.30 with 1 person
So available capacity should be 8 Hours as two person are working in two shift but system shows that two person are working for 16 Hours hence available capacity as 32 hours which is wrong.
Please let me know how we can show available hours as 8 in this case withoout changing utilization,no of ind.
Thanks,
Lalit

Dear Lalit,
1.In the capacity header of that work center,click on intervals and shift and click on interval by mentioning the valid from and to
date and allocate the shift sequence(first shift starting from 06:30:00 and ending at 15:00:00) and the second shift starting at
15:00:00 and ending at 23:30:00(assuming the length of brak for each shift has also been properly defined).
In the capacity header page also mention the active version as 01(for which you have defined the shifts).
2.Now in CM01,for the same work center in the top settings->General->mention the capacity version as 01 and check the
results.
Check and revert back
Regards
Mangalraj.S

What will happen if a maitain both standard available capacity and grouping key ( shift definition and shift sequence) in the capacity header of a work center?

Hi all,
Im little confused with the capacity header in work center. In the capacity header there is one place to give start time, end time, length of break and number of individual capacity. And in grouping key i can define the shift and shift sequence. So if im maintaining both of these ( standard avilable capacity and grouping key), which will be considered to calaculate avilable capacity?

Hi
If you are running three shifts ,please maintain the data as given belwo
start :00:00:00
End:23:59:59
Break :03:00:00 ( 1 Hour per shift so 3 hrs for 3 shifts)
No.of individual capacity :1
System will understand that it is round the clock operation with total three hour brak and you will get 21 hour per capacity
Hope this helps
regards
Prakash

BAPI for reading capacity of a workplace/work center?

Hi,
I'm looking for a BAPI/RFC using SAP MII to read the capacity of a workplace/work center in a given time period (eg. one or more days/weeks/...). I would like to use the import parameters plant ( WERKS ), date from, date to, workplace/work center (eg. CRHD-ARBPL ) and capacity category (eg. KAKO-KAPAR ). As output I would like to get a list of (planed/used) capacities as the working time for the given time period at the specified workplace/work center.
In theory the BAPI CBP_EXC_WC_CAPACITY_REQUEST nearly does what I want. The only drawback is, that it outputs the "wrong" time.
Let me give an example: The work center uses at a given day a capacity from 6 to 22 clock, including one hour break. This gives us a working time of 15 hours for this workplace and day. And "15h" is the time I need. But as there are working 5 worker at this work center the BAPI CBP_EXC_WC_CAPACITY_REQUEST returns 75 hours (which is 5 * 15). But the result "75" is useless for me as long as I don't additonal get the number of workers.
I've searched in our SAP system and in this forum, but wasn't able to find another BAPI that gives me the correct time. As an alternative I would need another BAPI to get me the number of workers for a workplace/work center at a given time. But I also was out of luck finding one.
Looking out for help,
Simon

Thanks for your fast reply!
I have looked to both functions before. Beside that they are both not remote enabled (which is not such a big problem as I could copy them or build a custom BAPI around them) I'm not quite sure how they could solve my problem.
If I got it right, I would first use CR_CAPACITIES_OF_WORKCENTER to get the KAPID and using it as input for CLOI_WC_CAPACITY_READ. But I have problems to understand the output of CLOI_WC_CAPACITY_READ. The data type of the capacity is a float ( FLTP ) and the number seems to be to big, eg. 9.800000000000000E+01= 98h for one day.
Could you try to explain your solution once again?
Thanks,
Simon

Costing in Work Center

Hi all,
I have a work center with an activity assigned. The cost of the activity has been maintained in KP26. E.g. 30 dollar /hour.
In the costing tab of the work center, i have added the activity and put in the formula SAP008.
When i do a calculation of the costing formula, i entered 1 day as the work duration.
The results for the calculation gives me 30*24 = 720. So it is giving me 1 day = 24 hours.
In the capacity tab, i have maintained the start, end and break time. Thus the operating time is 8 hours. Base of unit of measure is put as Days.
Any ideas where i would need to configure such that 1 day = 8 hours and the result of the calculation would be 30*8 =240?
Appreciate any advice.

Hi,
I think this 24 hours is not directly related to 1 day equivalant hours.The time is coming from the formula you have used SAP008.
Please create a formula which will take 24 hours as 8 hours for this resours.
For an example
Create a formuls x=SAP008/3
As 8 hours is availabe hours for your resource.The formula SAP008 use Work (internal proc) as a entry.Divide it by 3 by which you can get the actual run hours.
Hope this will help.
Regards,
kaushik

Maint.Work Center -Length of Break Hours-Reg

Similar Messages

Maybe you are looking for