Maintenance optimizer configuration Steps
Dear All,
I am stuck with Maintenance optimizer configuration.
Can somone provide a usefull link for the same i am using SOLMAN 4.0 with SP 15.
Best of regards,
Gaurav Sood
Hi ,
Here are the steps :-
MAITENANCE OPTIMIZER STEPS
1) Create the system in solution manager (Tr.code-SMSY)
2) For this System to create the rfc destinations.
3) Create the logical component for system.
4) Maintain technical settings of OSS in the transaction code: OSS1
5) In TR code AISUSER maintain the user and OSS id
6) In DSWP transaction codeu2014in settings-global settings have to maintain OSS id and Password.
7)go to tr code DSWPu2014changemanagementu2014support packagesu2014click on maintenance optimizeru2014select the systemu2014continue-confirm files in download basketu2014complete transaction.
Thanks
Abullais
Similar Messages
-
Maintenance Optimizer config step-by-step
Hi All,
I am not a SAP Basis Person,I install Solution Manager 4.0.
Now i want to configure it for SAP Service Pack downlod purpose.
Can any one help me in this regard in simplest way to configure Maintenance Optimizer.
Regds
GyanHi Gyan,
when setting up the Maintenance Optimizer, you will have to carry out the basic configuration steps from the Implementation Guide of your Solution Manager system (transaction SPRO):
SAP Solution Manager
- Basic Settings
-- SAP Solution Manager System
Follow the instructions step by step! Another important point from the Implementation Guide can be found under:
SAP Solution Manager
- SAP Solution Manager System
-- Activate Integration with Change Request Management
Furthermore check, if all necessary BC-Sets have been activated (Transaction SCPR20), these BC-Sets are as follows:
SOLMAN40_SDESK_BASICFUNC_000
SOLMAN40_CHARM_BASICFUNC_001
SOLMAN40_MOPZ_TTYP_SLMO
Make sure to have the table AISUSER maintained as described in the IMG, and check if the destination SAP-OSS (transaction SM59) is having the right settings.
Do not forget to assign a Logical Component to your Solution Landscape in the transaction SMSY.
Please check also note no. 990534.
Further information on the Maintenance Optimizer you will find under http://service.sap.com/solman-mopz
In case of any problems, just ask me again!
Regards
Csaba -
Maintenance Optimizer Configuration Guide
Hi All
I have a fully installed version of Solution Manager 4.0 SP12 and I am looking to configure the Maintenance Optimizer for monitoring our ECC and BW systems.
However, I feel that rather than using the wizards I need to set it up step by step.
My question, is there any documentation on how to set this up from Start to finish?
Manay thanks
PhilHello Guys..
The Step by Step Configuration of Maintenance Optimizer link is :
https://websmp105.sap-ag.de/~sapidb/011000358700000235502007E
Revert points is appreciated
Thank you.. -
Maintenance Optimizer Configuration
Hello,
I have 2 issues with maintenance Optimizer. I am using Solution Manager Support Package 9. I applied the notes related to it including the 1024932 and 990534.
1. When i press the button Continue in step 1, I sometimes have a runtime error PXA_NO_FREE_SPACE. I read that I have to change the buffer size, but I don't know how i can do it.
2. When I don't have this runtime error, in the step 2 when i press the button Select files, it opens an error page "the page cannot be displayed".
Thanks in advance
FrançoisHI François Maillard
For this you can ask to your BASIS Guy, If this server is test system, Then a simple restart will work in your condition.
Please let me know it it doesnt work,
Regards
Sukhii -
Solman_setup and maintenance optimizer configuration
Hi
We've newly installed Solution Manager 7.0 EHP1 and we want to configure maintenance optimizer for approving SP. Is it mandatory to use solman_setup tcode or can we configure maintenance optimizer via tcode solution_manager and smsy.
Best Regards...Hi
IT better if u use Solman_setup because it will run a wizard and do the needful and in a proper manner but still if u are expert and have already done the setting in previous version then u can it urslf.
Go through the links to know more about this solman_setup wizard settings.
New Guided Procedure for Configuration of SAP Solution Manager
https://websmp203.sap-ag.de/~sapidb/011000358700001927282008E
Demo on Guided Procedure for Configuration of SAP Solution Manager
https://websmp203.sap-ag.de/~sapidb/011000358700000316542009E/Procedure_Configuration.exe
Hope it will help ur more
Regards
Prakhar -
Error in Maintenance Optimizer in step "Select files for component "
Hi everybody,
i would like to download patches for my system. I have defined a solution and now i will start the Maintenance Optimizer procedure to download, but when i press a button "Select Files..." an error "the page cannot be displayed" occurred.
Does anybody know what should i check in my configuration? Where can I find more details for error?
Regards
BogdanHi,
Here is the whole solution for you.
Hope you have implemented the note 990534 properly.
This is what I have done to resolve the same issue -
Apply patch ST-ICO 8 and 9
generate BC set SOLMAN40_MOPZ_TTYP_SLMO_000
generate BC set SOLMAN40_CHARM_PROXYFACT_001
If the error still persist, you will need to work on the below notes. (997780)
Goto SPRO - IMG>SAP SOL MGR>SCENARIO SPECIFIC>CHANGE REQ MGMNT>EXTNDED CONFIG>CHANGE TXN>CONSISTENCY CHECK IN CHANGE REQ MGMNT (define basic settings SOCM_CHECK_002)
Deselect the 'Integr' field (integration with change management is required) for the checks listed below. The system issues a message stating that changes are not allowed and that the entries are SAP property. This is only a warning message. Choose ENTER to ignore the message and save your changes.
Checks:
IB_SYST_CHK
S_USER_CHECK
REQUEST_IN_PROCESS
SOLUTION_ASSIGNMENT
PRODUCT_ASSIGNMENT
S_USER_CHECK
EMPTY_CONTAINER
SYSTEM_STATUS_OK
If you are getting the error "no active ibase" after this, try to implement 1030498.
Hope this helps. If this corrects your issue, please mark the question as answered and award points.
Thanks,
Mehfil Meherali -
Maintenance Optimizer, approval step of download basket
Hello!
Im trying to download an update for our portal from the SAP web site, using download manager. But i can't get the file in download because this one has to be approve. I ve seen that this is done in Solution manager, but i can't find how to do it.Does someone know the step to solve this probleme?
Thanks & Regards
ChrisHi,
Have you setup maintenance optimizer?
The first Pre-requisite to setup maintenance optimizer is
SOLMAN to be
SP10
Also check these
[Tutor|https://websmp201.sap-ag.de/~sapidb/011000358700006477102006E.sim]
[Note|https://websmp201.sap-ag.de/~form/handler?_APP=01100107900000000342&_EVENT=REDIR&_NNUM=1024932&_NLANG=E]
This will solve your problem.
Feel free to revert back.
--Ragu -
Maintenance Optimizer configuration for SM7
Hi,
I am try to configure Mopz in my SM7.0 setup.
But at time of assigning S-user in tcode AISUSER, it is asking for "SAP Customer Number"
So my question is,
Is this the new field they mention in SM7.0? if yes then can anybod guide me how to configure it?
your help will be highly appriciated.
Thanking you
Regards
PranavHi,
Check with following sites.
1. https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/60d6ce0d-734f-2a10-e596-adbce4df51a8
2. http://www.sap.com/korea/services/pdf/Solman_4.0_Maintenance_Optimizer_Setup_Guide.pdf
Regards,
Srini Nookala -
Maintenance Optimizer "local logical system is not defined"
hello, i would like to create a new maintenance transaction to upgrade from SAP ERP 6.0 to SAP ERP 6.0 Enhanced Package 4 i follow the steps in the "maintenance optimizer configuration guide" BUT when i click to create a new maintenance transaction i faced an error told me "local logical system is not defined"!!! so how i can define Local logical system?
thanks in advance
Amr M. Abdelazeez
Mobile: 002 011 40 85 200
Linked In: http://eg.linkedin.com/in/amrabdelazeez/
Alexandria, EgyptThis should be configuration issue, please check the description in the Implementation Guide (tr: SPRO) at following point:
SAP Solution Manager
- Basic Settings
SAP Solution Manager System
General Settings
Maintain Logical Systems
After having maintained the logical systems, the error should not be displayed any longer. -
Client for maintenance optimizer
Hi friends,
Which client is to be ussed for maintenance optimizer configuration (its 000 or 001)
Kindly advice.
Regards
Ayush johriHi Thomas,
I want the automatic calculated delta of available support packages and the actual support package level of my systems and for this i have to connect my DEV system and assign them to a logical component
1. How can i connect the DEV system to the logical component (if you can guide me through the steps )
2. As of installing Sol Man i havent created any solution manager landscape, now as you said sol man landscape would be used for connecting the DEV system to it. how can i do this ?
Please advice.
Your suggestions would be highly appreciated
Regards
Ayush -
Solution manager optimizer configuration
hi
I am in solution manager 4.0 optimizer configuration step here i face an error when i type the t code solution_manager it displays the appropriate screen then i click on new button
here i entered the
solution name sandbox landscape
language english
then when i click on continue button here nothing is happening actually it has to go to the next screen but the screen stands as if, nothing is happening no reponse at all
support pack updated to stack 09
internet explorer 7 version is installed and all prerequisite is done
please help me
regards
senthilHi,
Can you tell what the error is? I may be able to help you.
Amol -
How to approve in maintenance optimizer for download.
Dear All,
I need to download support pack and other software like SAP JVM Switch tool 1.0 from service market place.
It is asking for approval, Could you please specify which tcode is needed for maintenance optimizer and step by step
solution to approve the software.
Regards,
DilipHi Dilip,
refer link :
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/304f52c1-3aae-2910-6081-8d1deace58f3?QuickLink=events&overridelayout=true
look for section Maintenance optimizer - Screens , where step by step screen shots are provided to approve packages.
You need to go to Tcode DSWP --> go to correct/active solution --> Change management --> Maintenance optimizer
Make sure that the SAP user id you are trying to access have S user id linked , check Tcode AISUSER
Regards, -
How to configuration Maintenance Optimizer in Solution Manager 4.0?
Hi All,
Can any tell me How to configuration Maintenance Optimizer in Solution Manager 4.0?
If any one having the document for same then please give me.
My mail id is : - <email address removed by moderator>
Thanks a lot,
HarshalHello Harshal,
Please go to service.sap.com/solutionmanager, click on the "maintenance optimizer" link, then a step-by-step guide is available there.
Another document is attached in Note 990534.
If you have further issues, Note 1024932 might be a good starting point.
Best regards,
Victor -
Configuring Maintenance Optimizer issue
Hi All,
This is the first time I am configuring SM 4.0. I am done with installation, and want to conigure maintenance optimizer.
I followed the IMG guide step by step.
But after all done, there are no systems listed under the maintenance optimizer of my Solution Landscape.
Instead I get a message:
<b>Change requests cannot be displayed or created, because the RFC connection has errors, or is not maintained.
Check whether the RFC connection to the Change Man agement system is under the key CHARM_DEST (APPLI field in the DESTINAT field), in the view BCOS_CUST. You need authorization for the cross-client view/table maintenance (S_TABU_DIS and S_TABU_CLI).
Check the RFC connection in the transaction SM59. If your SAP Solution Manager system is also your Change Manager system, the internal connection must be 'NONE'. You need authorization for the administration of RFC connections (S_RFC_ADM).</b>
Meanwhile I have issue with my J2EE engine not starting due to some UME issues, which I am working on parallely.
Please do let me know what would be the issue.
I have followed the note 990534 and doen with the BC sets.
But I am not sure where am I making a mistake.
One more doubt is, does maintenance optimizer connect to the SAP service market place through SAPOSS??? and am I not seeing anu system because my SLD is down. Please bear with my ignorance, I am a little lost here.
I have completed the solution landscape, logical component, etc.
Please help...
Regards,
SapfanHi JP,
My current SP levels are:
SAP_BASIS - 0011
SAP_ABAP - 0011
PI_BASIS 2005_11 - 0011
ST-PI 2005_11 - 0003
SAP_BW - 0011
SAP_AP - 0007
BBPCRM 5 - 0007
CPRXRPM - 0007
ST400 - 0010
ST-ICO - 0008
ST-SER - 0007
The issue is I did not connect to SAP yet, as I have only one RFC generated i.e. SAPOSS> Since my SAPRouter is not yet configured, I will connect to a valid SAPRouter once all the SM config is done.
I als got sone error in generating RFC for the main system when I used the wizard. I selected Change management and customizing directory and also selected Assign RFC for system monitoring.
I changed back the UME source to client 001, but still same.
Moreover the maintenance optimizer is not showing the satellite system.
I am really stuck.
Please let me know if you require more information.
I created the main system and defined the solution, as per the SPRO->Solution Manager -> Advanced Configuration -> Basic settings ->
I started this only after applying SP10.
Now I don see the systems both for Setup Solution monitoring and in maintenance optimizer.
WIll the system not reflect is the java ebngine is down???
Regards,
P.K -
Configuration of Maintenance Optimizer and IMG-configuration
Hi!
I am installing SAP Solution Manager 4.0 and two ERP-systems and would like to ask, whether a suitable detailed documentation about
Configuring Maintenance optimizer
IMG-Configuration
does exist?
P.S. Besides the document "Step by step Confugaration of Maintenance Optimizer" or .sim-File.
Thank you very much indead!
regardsDear Axel,
Kindly review the URL :
http://service.sap.com/solman-mopz
On the first page at the bottom end you would find an PDF for configuration of Maintenance Optimizer and also an SAP Tutor file for the same.
Follow the steps and you are ready with the optimizer for downloading packages.
Hope the above information helps.
Regards
Amit Devale
Maybe you are looking for
-
Mobility Radeon 7500 OpenGL issues
Whenever I attempt to use anything involving openGL, my CPU usage hits 100%. Complex openGL programs will drop to a framerate of less than 10, and sometimes crash Xorg. How can I fix this? General system info: lspci 00:00.0 Host bridge: Intel Corpor
-
Select option in time using oracle
i attach an excel file in oracle, i have a time field in my table, i give the select option in time ie, i select the time 4:00:00 - 6:00:00 in that time period data will display, for example html format ie, output format.
-
Hi I have a problem I forgot my pass for unlocking iphone with Touch ID.If someone know how I can remuved please tell
-
Hi, could some, how to make this effect in Motion?. http://vimeo.com/16285916 Thanks
-
Tree based on ViewObject with bindparams
Hi, We have some pages that are tree-form based; the tree and the form and based on two different viewobject usages, but the same viewobject. This VO uses a bind parameter to limit the data. With JHeadstart we can provide this bindparameter with the