Maintenance Plan: Change Yearly cycle

Hello,
We created maintenance plans for an equipment that has: Weekly, Monthly, Quarterly, and Yearly task.
THe date we initiated this maintenance plan was 6/1/2009. Is there a way to change the Yearly task date to 6/30/2010, but still keep the rest of the cycles the same dates?.
*Note we currently have a s'Schedule date of "0 days"
Thanks.

Hi Jay,
I assume that you are using a Time Based Strategy Plan for this. I also assume that you have created Packages of Weekly, Monthly, Quarterly, and Yearly in the Strategy & a Suitable Task list for it.
If you have not done my assumptions, please do them first and then carryout below steps. (Aviod weekly package if you want the date exactly on 06/30/2010, if it is compulsory then you will get approximately yearly package at that time)
After you create a Strategy plan for the Equipment and save.
Set Scheduling Indicator as Time-Key Date. (Possible only with packages in multiplications of Months)
Goto IP10 and Say Start in Cycle & give the Completion date as 6/30/2009 and in the Offset select the package as Yearly.
Now all the dates will adjust based on the requirement.
Regards,
MLN Prasad

Similar Messages

Preventive Maintenance Planning - change call date of future calls

Hello,
we are using time based maintenance plans to schedule our maintenance obligations towards customers. After creating the plan and scheduling (IP10) we get the scheduled calls proposed by the system.
Now we want to use IP10 or IP19 to move those planned call dates that are in the future without releasing the predecssor calls but it gives us an error: "Maintenance plan 16.04.2009: Predecessor to still on hold".
Does anyone know if there is a way around this?
Thanks,
Tobias

Hi Tobias
As per your query... you cannot move the call dates which are in the future. First you have to skip the cal which are before the future cal date. then only you can do...
- Pithan

Table for maintenance plan and maintenance cycle and Unit

Hello,
I need to know the table where the values are stored for maintenance plan, maintenance cycle and Unit.
I know that we can get the maintenance cycle and unit from MMPT table.
Question 1
If the maintenance plan has only a single cycle then the data is stored in above table MMPT, but if a maintenance plan has mutiple cycles like 1 maintenance plan has maintenance cycle as 364 Days and 1092 days then the data is not stored in MMPt table.
Question 2
Requirement is I need to develop a report where in I need maintenance order, maintenance plan and the relevant maintenance cycle and unit. Supose an maintenance order is created for the above maintenance plan which has 2 maintenance cycle how can I identify for which maintenance cycle the order is created.
Regards,
Narendra

Hi,
Please review PM tables
PM/SM/SD Tables
MPOS                       Maintenance Items
AFAB     Network - Relationships
PLKO     Task list
PLAS
AFFH     Operations
PRT assignment data for the work order
AFFL     Work order sequence
AFFT     Order process instructions
AFFV     Order process instruction values
AFFW     Goods movements with errors from confirmations
AFIH     Maintenance order header
AFKO     Order header data PP orders
AFPO     Order item
AFRC     Table of planned changes to conf.: Automatic goods receipt
AFRD     Default values for collective confirmation
AFRH     Header information for confirmation pool
AFRU     Order completion confirmations
AFRV     Pool of confirmations
AFVC     Operation within an order
AFVU     DB structure of the user fields of the operation
AFVV     DB structure of the quantities/dates/values in the operation
MPOS     Maintenance ITEM
AFWI     Subsequently posted goods movements for confirmations
AUFK     Order master data
AUFM     Goods movement for order
MPLA     Maintenance Plans
BGMK     Master warranty header
BGMP     Master warranty item
BGMS     Text item master warranty
BGMT     Master warranty text
BGMZ     Warranty counter information
CRHD     Work Center Header
CRTX     Text for the Work Center or Production Resource/Tool
EQKT     Equipment short texts
EQST     Equipment link to BOM
EQUI     Equipment master data
EQUZ     Equipment time segment
HIKO     Order master data history
IFLO     Functional Location (View)
IFLOT     Functional location (TABLE)
IFLOTX     Functional location: Short texts
IHGNS     Plant maintenance permit segment
IHPA     Plant Maintenance: Partners
IHSG     Object-related permits in Plant Maintenance
ILOA     PM object location and account assignment
IMPTT     Measuring point (table)
IMRG     Measurement document
KAKO     Capacity Header Segment
KONP     Conditions (Item)
KONV     Conditions (Procedure Data)
OBJK     Plant Maintenance Object List
QMEL     Quality notification
QMFE     Quality notification - items
QMIH     Quality message - maintenance data excerpt
QMMA     Quality notification - activities
QMSM     Notification - Tasks
QMUR     Quality notification - causes
STPOA     Name is does not have an A at the end; BOM items
T001     Company Codes
T001L     Storage Locations
T001W     Plants
T077D     Customer account groups
T003O     Order Types
T352R     Maintenance revisions
T353I_T     Maintenance activity type description
T356     Priorities
T357G     Permits
T357G_T     Table 357G texts
T370A     Activity category for PM lists
TINCT     Customers: Incoterms: Texts
TVKO     Organizational Unit: Sales Organizations
TVKOS     Organizational Unit: Divisions per Sales Organization
TVKOV     Org. Unit: Distribution Channels per Sales Organization
TVTA     Organizational Unit: Sales Area(s)
VIAUFKST     Order selection view
MMPT Cycle detail
Regards
Carlos

Maintenance plance with several cycles

hello all
I have a maintenance plan containing several cycles: the most importants are 1 year 6 years and 12 years.
Closing date of an order of any cycle, influences the starting dates of the others.
Meaning: if I close the 6 years 6 moths later, the 12 years is going to have the starting date pushed off for 6 month.
we want to avoid this: we would like the closure of the order not to influence the opening of the next.
apparently there is a user exit that allowas that??
or any other idea?
thank you
Alisa

Here are the two things:
1) if you put the value of all the parameters to zero , the next call date will not be shifted . means if 6 years cycle is delayed by 6 months , the 12 year cycle will call object on the plan date , No shifting will be there for 6 months or so. . So one of your problem will be solved.
2) And if you want to put the completion requirment tick thats ok.
System will not flooded with orders as the orders will come which are planned and that much numbers of orders are expected when you configure the system.
you can put the completion requirement tick and put the values to zero. So order will only be created when last order is TECO and also the dates will not be shifted as per the shift factor.

Maintenance plan report.......

hi all,
please any one help me to solve this issue....
my client wants ... A report to show all preventive maintenance objects call/planned dates of maintencenance plan, which were issued,completed and not completed with status issued,completed and not completed.....for the last 12 months.....
so can any one share the procedure means from which table i can get the info to solve this issue so that i can do customized report with the help of ABAP coding..
thanks in advance.........
regards
gunnu

Hi,
     Check the below tables :-
MHIO     Call Object from Maintenance Order
MHIS     Maintenance plan history
MMPT     Cycle definitions and MeasPoints for MaintPlan
MMPX     Maintenance cycle short texts
MPLA     Maintenance plan
MPOS     Maintenance item
T351     Maintenance strategy
T351P     Maintenance packages
T351T     Maintenance strategy texts
T351X     Maintenance strategy package texts
T399G     Maintenance Plan Sort Field
T399G_T     Descriptions for Maintenance Plan Sort Fields
T399P     Maintenance item category parameter
T399W     Maintenance plan type parameter
T399W_T     Maintenance plan category descriptions
VIMPOS     Maintenance Item (view)
1. You have different status at MP Call object level , Called , Completed, Hold, fixed, skipped, Manual,
2. For MP :- CRTD,Inactive, Locked, Deactivated etc
3. You need to differentiate via Maintenance Plan Category
4. Call Object Status
5. Maintenance Plan status
6. Time period
etc
regrds
pushpa

Change start of cycle date in maintenance plan

Dear Experts,
We would like to change start of cycle date in maintenance plan. Iwe have rescheduled the plan but the start of cycle date remains the same.
could you please confirm, whether it can be changed. The requirement is because of some Mt plan created with future start date in production (Year-2020) and we want to correct the same.
Thanks

Don,
To determine the next maintenance call date you need to tell the system when the last maintenance call occured
Example:
You want the next call date on the 1 June based on a six month cycle. Therefore the last maintenance date would have been 1 January (assuming key date scheduling).
In your case you need to RESTART your single-cycle plan on the 1 January and the system then calculates the next maintenance calls.
PeteA

Change or Add Cycles in a Maintenance Plan (IP02)

good afternoon all,
we have an issue with a number of maintenance plans that were setup as 1 year cycles, and now we want to run them as monthly. Is there a way to either change the yearly cycle to monthly, or add a new monthly cycle?
SAP ECC6
Release 731 sp level 0007.
Thanks.

Greetings Santosh,
You are correct, the key word here is "approximately", as the Cycle Modification Factor has only two decimals of precision, you will need to input 0,08 to reflect the appropriate factor of 1/12=0,08(3) - so that will mean your cycle is 360*0,08=28,8 and not 30 days, which is why I did not propose this route. But if it's not an issue, then yes, that's another way to do this
EDIT: Which reminds me, after switching the cycle to monthly, consider if you require Time or Key Date scheduling on the Maintenance Plan scheduling parameters, as for SAP 1 Month = 30 Days with the former, but with the latter the scheduling is always for the same day of each month.

Changing a cycle in an active maintenance plan

Hello All,
I received a request from an end user to make a change to an active maintenance plan. The plan has a 3mo cycle. The users would like to first, generate a call for March 2011 and second, to change this to a an annual cycle. I am able to use the 'Restart in Cycle' to generate a call in March, unfortunately, I am not able to figure out how to change the cycle from 3mo to 12mo. Is it possible for to change the plan cycle from 3mo to 12mo once the plan is started? The header section in IP10 is grayed out.
At the moment, it looks as though I need to create a new maintenance plan to accommodate the request.
Thanks in advance.
Anna

Mahee,
Appreciate your quick response. This was a strategy plan and I was able to make the changes as you had suggested, through the task list.
Thank you so much for your help!
-Anna
Edited by: Anna Vuong on Feb 24, 2011 10:08 PM

Changing Cycle Modification factor in a maintenance plan.

On the basis of MTBF of an equipment, Can i change cycle modification factor of any maintenance plan.i.e. suppose MTBF of an equipment if reaches to 3 months then cycle modification factor for all preventive plan should get multiplied by 1.5 automatically.
please suggest on this thanx
ravi

hi
in standard it will not automatically change ,you have to make it manually .
another workaround is create it like test equipment and follow the calibration process ,while making the usage decision you can specify the modification factor.
regards
thyagarajan

Change/restart start of cycle for strategy maintenance plan MPLA- STADT

Dear experts,
is it possible to change the start of cycle date in strategy maintenance plan (MPLA- STADT).
The start of cycle was entered incorrectly into the strategy maintenance plan (IP42)
Maint. plan was already started
...and called: Service orders are already created
The existing maint. plan should be used with a new cycle start date.
By using u201Crestartu201D in IP10, a new start of cycle date is entered and the orders are called correctly.
But the cycle start date is not updated in the data base: MPLA- STADT
Why?
Regards,
Philipp

Dear all,
I opened a OSS message. SAP replied that this is not covered by SAP standard. so system works as designed.
SAP:
The described behaviour is the SAP/R3 standard and works as designed.
IP16 only shows this field if it's updated in MPLA-STADT.
The 'Cycle start' resulting of scheduling (IP10) is kept in the table
MHIS (field STADT).
Transaction IP16 takes data from MPLA and does not read the entries
in MHIS. The only value that can therefore be shown as 'cycle start'
is the original value as recorded in MPLA.
Well, this explains why system behaves like it does.
But in my eyes this is not the correct system behavior.
If a maint. plan is restarted, future calls will be calculated based on
the new cycle date - what is ok.
But IP16 indicates the old cycle date!
In my eyes this is not correct because the list will show an incorrect
cycle date.
I was told to take a look at note 11:
Sehr geehrte Kundin, sehr geehrter Kunde,
die von Ihnen benötigte Funktionalität ist leider nicht im SAP-Standardsystem enthalten.
Wenn Sie mit SAP an zukünftiger Produktfunktionalität arbeiten möchten, empfehlen wir Ihnen, dies entweder über die Mitarbeit in einer SAP Anwendergruppe oder über die Mitarbeit in einer der SAP Communities of Innovation zu tun. Eine Liste aller SAP Anwendergruppen finden Sie unter http://www.sapusergroups.org.
Eine Beschreibung der SAP Communities of Innovation können Sie unter http://www.sap.com/ecosystem/communities/index.epx einsehen.
Alternativ können Sie spezielle, von Ihnen gewünschte Funktionalität von SAP Custom Development entwickeln lassen (http://www.sap.com/services/bysubject/customdev).
Weiterführende Informationen finden Sie unter http://service.sap.com/rollin.
Mit freundlichen Grüßen
Ihr SAP Active Global Support
How can I trigger such an improvement?
Regards,
Philipp

Planned Maintenance/ Activity but no cycle time

Hi PM Gurus,
Quite new to Plant Maintenance, and would like to ask a question.
I have a planned program for maintenance of some plantation, which requires maintenance lets say,
on February and October of the year for one type of activity, and maybe June and September of the year, for another activity, so they may not have any cycle time, but they require to maintain it for twice
a year. Its more of a program scheduled for each of numerous activities required to maintain
the plantation.
Is this considered as Preventive Maintenance or Ad-Hoc Maintenance, as there is no exact cycle
time as required to be set for Preventive Maintenance, but its a planned activity.
Thanks so much for your help. Best Regards

pocoyo ford,
The first question you probably need to answer is whether there is any legal requirement to prove you perform planned/routine/preventive/routine type maintenance. If so, then you will probably need to create maintenance plans (although there are other non-SAP methods too).
If the maintenance is Feb/Oct then you can use a standar 6 monthly cycle. However, you may need to use factory calendar for the Jun/Sep cycle.
But if one equipment toggles between a Feb/Oct and a Jun/Sep cycle, then maintenance plans may not be the most efficient way as you would need to change the maintenance plan each time the cycles change and the administration time may be too great...
PeteA
[www.pjas.com]

Start cycle date in maintenance plan

Hello Every one,
In my project i have uploaded all the plans in production server with start cycle date. Now when i am going in change mode i cant see the start cycle date even thoug i can see the scheduling overview in plan as correct date but i m not able to see the start cycle date. Kindly help me in this.
Regards
Abhishek Sinha

Hi,
In Maintenance Plan, once you have mentioned the start of the cycle. Again it wont appear in Change Maintenance Plan, you will have to restart or reschedule the Plan.
Regards,

How to change maintenance Strategy in Maintenance Planning?

Hi Friends
In our maintenance plan, maintenance plan additional data, maintenance strategy is defined as 3M6M. Within this strategy, maintenance cycles are defined. Now we want it to change to the maiintenance strategy, 2M that is bi monthly. How to do it?
Do I need to chage it in the maintenance plan category? I am very new to PM. Pls explain.
Thanks
Sangeeta

Dear,
It is not possible to change the maintenance strategy once assinged to task list,other option just try in the task list select the operation and select the maintenace package ,here delesect all the maintenance package alloted and then try to change it.
First delete all the operations in the task list ,then system wil allow you to change the maintenance strategy.
Best way is to create new maintenace plan with new strategy.
Hope clear to you.
Regards,
R.Brahmankar

Maintenance plan package change resulting in incorrect call dates

When we change a maintenance package on an existing maintenance plan to a package whose frequency is not an exact multiple of the previous package (for example, changing from a 6M 180-day package to a 1Y 365-day package) and then restart the plan, the call horizon of the plan seems to be ignored and the new call dates are always a day or so before the plan date regardles
Why is the call horizon being ignored in this situation?

Hello
Please check the Option Start in Cycle while scheduling the Plan.
Also refer the below thread too
http://scn.sap.com/thread/1788240
Br
Rakesh
Message was edited by: RAKESH MANE

Maintenance Plan which has two call dates for year

Hi all,
I need to create a Maintenance Plan which has two call dates for year. The dates have to be the last Sunday of March and the last Sunday of October for the same Maintenance Plan. Does anyone know the solution? Please do throw some light on it.
Thanks
S
Edited by: Sara Silva on May 14, 2008 11:39 AM

Sara,
You could do this without user-exits...
Create a factory calendar with two working days. Then create a maintenance plan with a package of 1 day.
Once scheduled it should produce the required maintenance cycles.
There are two things you need to be very careful about:
1. Keep the factory calendars updated, say, 3 years into the future
2. Ensure you comprehensively test the IP30 transaction
PeteA
[www,pjas.com]

Maintenance Plan: Change Yearly cycle

Similar Messages

Maybe you are looking for