Major Problem with audio from Final Cut to DVd Studio Pro

I am posting this problem again because no further responses have been received regarding my first post. I purchased an MR-HD100 Firestore device from Focus Enhancements. When I use clips from it alone or with other clips created by digitizing from min DV tape on a sequence or timeline the audio works fine in Final Cut. When I import any type of file and believe me I have been trying all kinds of suggestions and wasting almost a dozen DVDs. Whether it be a Final Cut QT file, going straight to compressor and producing an MPEG-2 file and a dolby audio file .ac3 importing them into DVD SP and making the adjustments that MR. Harbsmeier suggested DIAL NORM at -31dbfs and COMPRESSION MODE to NONE, as well as the suggestion to make an aif file with the audio and importing it into DVD SP as well as the video. I get the same result with every try, the clips made with the firestore are so low you cannot hear them. NOTHING WORKS!!!!. And yes I have tried making a DVD with just digitized footage and yes it turned out fine. I called Apple support today and that gentlemen basically told me I am out of warranty so phone help was not available. However, he made a suggestion of changing sequence presets in Final Cut which has now developed into another problem. I have messed up my settings so bad I don't know where I am I can't LOG & CAPTURE in the manner I used to ???? Could someone please advise as to why this problem exists and the correction to resolve it. I do not understand why the audio works fine playing the sequence on the timeline in Final Cut. It plays fine after making a Final Cut QT file. AND it plays fine in simulation mode in DVD Studio Pro. However after you burn a DVD the audio from the firestore clips are not to be heard unless you crank up the speakers or TV to it's maximum level and you can barely make it out. PLEASE PLEASE PLEASE HELP ME Projects are stacking up and was really hoping to go tapeless

Try building the project to your desktop and then open the Video_TS in the Mac DVD player application.
How does it play/sound? This application is the best way to see and hear how your burned DVD should play vs. just using simulator and burning.
Just to clarify- are you taking your FC QT file into Compressor and creating a MPG-2 and AC3 file or are you bringing your FC QT directly into DSP?
What codec are you exporting from FC? ProRes422, DV, H264?
Open the FC QT in QT and apple+I to see this.
What does it say for audio?

Similar Messages

Problem sending timeline from Final Cut to a Soundtrack Pro Multitrack Project

Hello,
Thank you in advance for reading. I am having trouble sending a timeline from Final Cut to a Soundtrack Pro Multitrack Project. Final Cut makes a new Soundtrack Pro project file just fine and opens Soundtrack Pro as it's supposed to, but the project in Soundtrack Pro only has a portion of my audio tracks. I've tried sending by control clicking the sequence in the browser and selecting 'Send to Soundtrack Pro Multitrack Project' as well as highlighting my entire timeline and doing the same. Both result in the same Soundtrack Pro proejct with about 1/3 of my total 48 audio tracks (lots of sound FX).
I'm using Final Cut 7.0.2 and Soundtrack Pro 3.0.1 My computer is a Macbook Pro running OS 10.6.8, 2.26 ghz intel core 2 duo, 4 gb ram.
Any suggestions (or workarounds, if it comes to that) anyone has will be greatly appreciated.
Thanks again, Gabe

Try building the project to your desktop and then open the Video_TS in the Mac DVD player application.
How does it play/sound? This application is the best way to see and hear how your burned DVD should play vs. just using simulator and burning.
Just to clarify- are you taking your FC QT file into Compressor and creating a MPG-2 and AC3 file or are you bringing your FC QT directly into DSP?
What codec are you exporting from FC? ProRes422, DV, H264?
Open the FC QT in QT and apple+I to see this.
What does it say for audio?

How to import subtitles made with Final Cut in DVD studio Pro?

Hello!
I made subtitles for a movie directly on a track of my final cut timeline. How can I import now this into DVD studio pro to make an independant subtitle track?
thank you.

DVD Studio Pro can work with STL subtitle files. they are nothing more spectacular than a plain text file.
There's a ton of information in DVDSP's online manual, under the Help menu bar item.
search that pdf for "Creating an STL Format Subtitle File".
This file can be configured to display when the user wants to see it or made permanent with the "Force Display" option.
If you export your FCP Timeline the subtitles on it will be burned into the video permanently.

Aperture and other Pro Applications ( Final Cut, Motion, DVD Studio Pro )

Hi folks,
I have bought Final Cut Studio a while back, and have been working with all the tools for a while now ( FCP, Motion and DVD Studio Pro ). Recently I also switched to Aperture to manage / capture / organise my digital photographs ( previously I used iPhoto ).
Now I was wondering how I could use the pictures from my Aperture library in Motion or DVD Studio Pro. When I look at the file Browser, I can easily use some iPhoto pictures, but apparently I can't seem to find anything for Aperture.
What I would like to do is use some pictures from Aperture in a Motion project and also include an Aperture album in DVD Studio as a SlideShow.
What would be the best way to do this ? Do I have to export the pictures I want to use ? Or am I missing something ?
Regards,
Stefaan

Stefaan,
Unfortunately, that type of integration between the Pro Apps is not there (yet). It would definitely be a nice feature to have. We should all send feedback to Apple asking for this feature. For now, you will need to export photos for use in these other apps.
Along the same lines, I would also like to see integration with Aperture and the "iLife" programs. Since Aperture will likely replace iPhoto for at least some of us, it would be nice to be able to use Aperture photos in these apps as well.
--Joe

Please, suggestion about final cut x, dvd studio pro, sound track and color

what to do now, final cut studio cannot exist in same partition of fc x, but at same time fcx does not have anymore dvd studio pro, color and soundtrack, is it replacing the 3 programs? are you really satisfied of it?

Try building the project to your desktop and then open the Video_TS in the Mac DVD player application.
How does it play/sound? This application is the best way to see and hear how your burned DVD should play vs. just using simulator and burning.
Just to clarify- are you taking your FC QT file into Compressor and creating a MPG-2 and AC3 file or are you bringing your FC QT directly into DSP?
What codec are you exporting from FC? ProRes422, DV, H264?
Open the FC QT in QT and apple+I to see this.
What does it say for audio?

FINAL CUT AND DVD STUDIO PRO 4

One quick question is it alright to transfer a project into final cut pro while you have a project in dvd studio pro 4 doing the asset incoding, It seems to be working ok but wasnt sure if that would mess up anything in the encoding,
thanks Bill

It shouldn't make a diifference in the encoding. I usually use Compressor instead for a few reasons I can explain if you are interested. But in answer to your question, the encode should be fine under these circumstances. The only iissue you might expect to encounter would be dropped frames during playback in FCP, because the encoding process might be using the same drive, both reading and writing, and perhaps even the same files, as the media FCP is trying to play back. Shouldn't hurt anything, though.
Hope this helps -
Max Average

Simple Q regarding Final Cut and DVD Studio Pro

Why can you not use .mov files exported through QuickTime Conversion in DVD Studio Pro? What is the best format to use .mov files exported through QuickTime Movie or avi files?

The point being made is why you are doing a QuickTime conversion?
The best practices workflow for many:
1. Export self contained current settings audio and video;
2. Open Compressor and assign the DVD preset for video consistent with the length of the video in minutes and the Dolby2 audio.
3. Take the video m2v file and audio AC3 file and import those into DVD SP.
Do not use DVD SP to do the encoding because it lacks the controls Compressor does and forces the use of aiff audio.

I am having a problem with playback in Final Cut 6.0.6

Hello,
I am having a problem with playback in Final Cut 6.0.6 of 1920x1080 60p footage.
I transcoded MTS files shot on a Sony NEX FS100 into Apple Pro Res mov files but the
playback stutters in Final Cut and QTime making it impossible to edit. Is this because the files
are just so big the computer is having a problem processing them? If so what should I edit in to preserve the
best quality?
I am Running Mac OSX 10.6.8
2x2.4 Ghz Quad Core Intel
32 GB 1066 MHz DDR3
Admittedly my FCUT is out of date, I intend to up to X when I finish off an ongoing project.
Thanks Luci

You might consider running diskwarrior on your drive (alsoft.com). And run diskutility, repair disk. A corruption of the drive could cause problems. Also, drive speed starts to fall sharply as the drive gets full. Make sure you have a minimum of 10% free space on the drive. You might also get a utility to check the speed of the drive. I think Aja has one.
Also, do you have anything else connected to the firewire bus? If so, try disconnecting it. You might also try disconnecting ethernet and turning off your airport. Resetting your fcp preferences couldn't hurt.
https://discussions.apple.com/docs/DOC-2491

Can I mute all audio from Final Cut Pro X?

Can I mute all audio from Final Cut Pro X so that I can listen to music while I do sorting, keywording, favoriting, etc? I'm doing a video where all the camera audio won't be used anyways, so I don't need to hear it in FCPX.. I'd rather just listen to my music instead. Thanks.

For clips in the timeline, andynick's suggestion works fine - temporarily disable the audio roles will play everything without audio and you just have to reenable these roles later.
For clips in the Event Browser, you can also disable and reenable audio for a bunch of clips all at once. Select the all the clips you want, open the inspector, click the audio tab and uncheck the box (for "stereo" or "mono" or whatnot) under "Channel Configuration". Again, to reenable just check this box again.

Converted from Final Cut 7 to Premiere Pro CC

Hello totally awesome community of hard working people who make cool things!
I am converting from Final Cut 7 to Premiere Pro CC. I've been in for 1 day and am impressed that many of the shortcuts are the same.
I have much to learn and am studying every day.
Do you have any recommendations for any great free video tutorial series on this software?
Thanks!
Check out the film I made with Final Cut 7. I'm excited about Premiere Pro CC because it will save me a lot of time!!
Beyond the Music: Soundscapes, El Sistema and the Proven Power of Music | Video Portal (El Sistema USA)

Hi soundscapes,
Here you go: http://tv.adobe.com/product/premiere-pro/
There are more on paid websites.
Thanks,
Rameez

Export from FCP directly into DVD studio pro?

Is it possible to export from FCP directly into DVD studio pro? If not, what is the preferred file format because my exported quicktime files come up as "incompatible format" when I try to add them into my DVD project. Any help is appreciated.

You need to encode audio as well from Compressor. You'll have 2 files - audio and video.
Here's a tutorial:
http://www.youtube.com/watch?v=wFgJpd7DEWw
Message was edited by: Eric Pautsch1

Audio from Final Cut Pro very very low

Hi guys I have not have a problem for awhile. A friend of mine recently move from DPS Velocity system to Final Cut Pro Studio 2 using a Intel Pro 3.2GHZ with all the bell and whistle, so I am giving him some training and tutorial. They have some footage in Velocity which I use MPEG StreamClip to convert to a DV file, I brought it in FCP (Three File one video and two audio makes one clip) it play in FCP Played ok when I export it to DVD studio Pro the audio is extremely low (barely audio able)I open the clip in QuickTime and it did not play. There is other clip in the project, some capture in FCP and others imports in FCP Studio, DVD Studio Pro and QuickTime plays these audio ok. The audio from Velocity are Wave files, I taught anyfile that plays in FCP would play in QuickTime. Does anyone knows how to solve this problem please to help I would like my friend to change both system to Apple and FCP thanks.

Wellcome to the forums!
when I export it to DVD studio Pro the audio is extremely low (barely audio able)I open the clip in QuickTime and it did not play.
I guess you encoded it to Dolby AC3 with Compressor, did you? Then you must chamge the standard Dolby preset as follows to keep the original FCP mix and level:
- Dialog normalization: -31
- Compression preset: none
And QT cannot play AC3 files.
Hope that helps !
Alberto

Best way to go from Final Cut to DVD preserving Color Corrections

What is the best way to take my video project from Final Cut and burn it on a DVD (using DVD Studio), I need to preserve the color corrections I have made (used an external video monitor)? Also my camera shoots at black level IRE 0 and I have edited it that way, but as we all know NTSC TVs use IRE 7.5 is there anyway DVD Studio or FCP can convert the IRE so it matches?

from FC; export to compressor
In compressor, choose appropriate preset (i.e. best quality, >90 minutes, 16x9)
encode the sound as dolby 2 (if you choose "all" you'll get an extra aif file)
take the 2 files (video and audio) into dvd studio to encode.
Not sure about your IRE 7.5 question, I always assumed it was automatically converted but now you have me thinking...

No audio in simulator or viewer - DVD Studio Pro

First project on DVD studio pro.
I imported MPEG2 and AC-3 on the timeline, but when trying to play on either the viewer or simulator there is no audio.

Try to preview just the AC3 by double-clicking on it (assuming that all your system audio stuff is working...) if it plays, you may have an issue with the disk your MPEG-2/AC3 source is on.
If the AC3 doesn't play, you'll want to go back to the source clip you used in Compressor to assure that the audio was exported from the FCP timeline. If the source clip has audio, you'll need to re-open the source in Compressor, add the appropriate codec, test it in Compressor using the Preview function, then transcode it again.
Obviously if the audio was good in the timeline, then an export error occurred.
Post back where the chain broke.
Nevermind...

Is Compressor 4 necessary when sending from FCP X to DVD Studio Pro

I am making a FCP X movie and when it's finished I want to put it on a DVD using DVD Studio Pro. I have done this before but now I'm wondering if I should first export it to Compressor 4 and then to DVD Studio Pro. I understand that if I was puting it on YouTube or an iPod device I would need to Compress it however why would I need to go to Compresss 4 first if ultimately going to DVD Studio Pro? Would I get a better Codec quality then what I get from exporting in FCP X using their default Compression format i.e. Quicktime? Should I use an Apple ProRes Compression from Compressor 4? I guess I really don't understand the encoding quality options very well however I do want the best quality on my finished DVD. The DVD or Sequence is somewhere around 20 - 25 minutes if that makes any difference in your response.

People will tell you that encoding in Compressor will give the best quality, but that assumes you are using a suitable preset and for your length of video the ready made ones are unsuitable and will waste time as they are all 2-pass with variable bit rates (VBR).
For DVDs under 70 minutes long the best quality and fastest encoding times are achieved using a constant bit rate (CBR) of around 7.5mbps.
For your short DVDs you should achieve the highest quality and fastest processing by simply exporting the project from the timeline as it is, drop it into DVDSP and set DVDSP to encode and burn it at the specs I gave above.
Returning to my opening comment, you will frequently find that the theoretically best solution to a problem results in no discernible improvement but often entails a lot more work and time-expenditure.
P.S. You might get marginally better quality by raising the bit rate to 8mbps but you run a slight risk that some old or cheap players may not be able to keep up, resulting in dropped frames.
Message was edited by: Ian R. Brown

Major Problem with audio from Final Cut to DVd Studio Pro

Similar Messages

Maybe you are looking for