Major problem with MSI - K7N2G motherboard

i have just purchased an MSI - K7N2G motherboard, when i switch it on the test lights on the back do not light up and the computer does not even boot up the bios. then when i press the restart button the lights will light but hang on this problem - Initializing Hard drive controller, then when i restart again, lights 1,2 and 3 stay completely off and number 4 shows red and it just keeps switching from these two problems. i have also sent it back and they said there was no problem and have sent it back to me, but i still have the same problem can any one help me?? ;(

i have already got one of these pc's running with same spec except different harddrive, and because it was so cheap and easy to make i made another and since then had loads of probs!
here is my spec hope this will help!
MSI - K7N2G motherboard
1.3 Duron
Crucial PC2100 256mb DDR 184pin DIMM
Seagate Barracuda 60GB 7200rpm UDMA100 IDE Hard Drive - OEM
300w Psu
hope you can point me in the right direction
thanks

Similar Messages

  • Optical Out problems with MSI-K8NS Motherboard Adapter

    I have an MSI-K8NS motherboard which came with an extra PCI mount bracket for coax/fiber digital out sound. I just bought a Creative surround sound system set with digital decoder. I hooked the header into where I believe the pins should go into the motherboard and even have a light at the ends of the cable (seemingly has a signal, I presume). I have no idea how to enable this in software, however. The Realtek software that is installed doesn't seem to have any configuration for this digital out, and I can't find a way to use it. I've searched these forums, but still have no idea what's going on. Could someone please help?
    Thanks!
    Edit: Ok, so it looks like the SoundManager software needs to be in 8 channel mode for spdif to work. I don't understand that, but at least I got it working. Hope this bit of info could help someone else out!

    Quote
    My best guess is because you are running the default BIOS. Try running with one stick of ram just to start with, so that you have a stable enough system to upgrade your bios to 1.3
    I tried running the system with a single stick of ram and still the same thing happens
    Quote
    did i miss it or have you not mentioned that since your ram is 166MHZ you have changed the memory divider to 166 in BIOS?
    When I started the computer up, the motherboard automatically picked the memory modules up as 166Mhz.
    To Paul:
    I tried to run the memtest86 several times.  It starts off for a while, then the computer hangs up as pervious situations.  It could just be that the RAM i am using is imcompatible.  I may have to invest into Corsair RAM modules.

  • Major problems with MSI software.

    when i first got my motherboard i put in the cd and installed the MSI pc alert 3 and fuzzy logic 3.  pc alert 3 ran fine and since ive upgraded to 4.  but fuzzy logic gave me a load rushtop NT driver failed.  so i uninstalled it, then upgraded to fuzzy logic 4.  got the load rushtop error again, so i got the newest verion today.  got the rushtop NT driver message.  so i uninstalled it, then went into regedit and searched for fuzzy and deleted every fuzzy key i found.  i rebooted and loaded up fuzzy logic 4 and ran it.  i got a new error message, Load NT hardware Monitor failed.  so i got creative and copied the GLM7x.sys file from my pc alert 4 to my fuzzy logic 4.  i ran fuzzy logic 4 and it started up fine, i looked at the values and they were all blank or 0's and it tried telling me i had a p3 processor.  i uninstalled it again.  then my pc alert 4 stopped working, so i uninstalled it, then reinstalled and now the pc alert screen pops up and it runs but all the values are empty.  anyone know of ways to fix this problem, and/or get fuzzy logic 4 to work?  if not, do you know of any good software overclockers that work with 645 boards and windows XP Pro SP1?

    yeah it gives you an error that says pc alert or fuzzy logic is already running. i think it has to do with that thier system monitoring driver 'GLM7X.sys' is the same in both, but they are different sizes.  this maybe but the problem.  nonetheless i got pc alert 4 running again, just mysteriously started working.  went in and over clocked the fsb to 120.  now i have a 2.4. buti am concerned as this makes the ram and bus to everything else much faster.  the only thing thats really rated to o'c is the northwood. so what im wondering and why i am focusing on fuzzy logic as it allows you to do this, but to set the multiplier higher.  that way only the CPU o'cs and theres not such a danger of $400+ worth of ram, and $150 board along with a $175 processor going up in smoke, instead it would just be the proc.  any suggestions on ocing the multipler?  i know microshaft / intel stopped allowing you to o'c the multiplier, i know some software has this ability...

  • Strange major problem with 975X PowerUp Intel MOBO

    I’m suddenly having a strange major problem with a MSI 975X Platinum PowerUP Edition V2.1 MS-7246 Intel socket 775 motherboard. Previously, it had given me no problems at all.
    It went like this:
    Powered on system in the morning, booting from a cold start.
    Hit DEL key to get into the BIOS.
    Missed the window and the system booted into Windows normally.
    Re-started the system from within Windows.
    Hit DEL key to get into the BIOS and was successful the second time.
    Hit the ENTER key on the first item “Standard CMOS Features”.
    The DATE, TIME and other information was displayed on the next screen, but at this point, the BIOS screen became completely unresponsive to any keyboard input.
    The only thing I could do at that point was to power off.
    Subsequent power on boot-ups resulted in the system always freezing at the BIOS splash screen after the video card sign-on.
    I have switched power supplies, hard drives, keyboards and video cards. I have disconnected everything except the video card, keyboard and one RAM module. I have switched the four RAM modules around and then reduced the RAM to one 256MB module in the proper slot. I even changed the battery on the MOBO, in case it had shorted out and removed and re-seated the BIOS chip. It still halts at the BIOS splash screen.
    The BIOS chip can’t be completely dead, because I powered off and pushed the BIOS reset button on the MOBO to reset the BIOS to the factory defaults. When I re-booted, I could tell that it had actually reset to the factory defaults because I had previously set the BIOS to reboot the system on resumption of power and the factory default was to remain off until the power button was pushed, which was now the default.
    I’m stumped! All I can think of is to get a new pre-programmed BIOS chip and see if that makes any difference, but I’m not sure this system is even worth the expense with no guarantee of success. Any suggestions on how I might get past the BIOS splash screen or do I for sure have a corrupt BIOS chip?

    System specs as per the posting guidelines -
    Board: MSI 975X Platinum PowerUP Edition V2.1 MS-7246 Intel socket 775
    Bios: Version (can’t recall & can’t check since it won’t go past the BIOS splash screen)
    VGA: ASUS EN7600GS nVidia GeForce 7600GS PCI-e 256MB DDR2 (also tried new XFX nVidia
             Geforce 210 PCI-e 2.0 512MB DDR3)
    PSU: Chiefmax 680W ATX (also tried new OCZ 700W ATX)
    CPU: Intel 2.8GHz LGA-775 Core2 Duo Dual-Core Processor
    MEM: 4 x Samsung 512MB 1Rx8 PC2-5300U (2GB total)
    HDD: Seagate Barracuda 250GB SATA2 (also tried Seagate Barracuda 500GB SATA2)
    COOLER: Intel OEM LGA 775 fan/heatsink C25897-001
    OC: No
    OS: Vista Home Premium 32-bit
    I have been through the BIOS reset procedure several times and pretty much as outlined. As I said before, I could tell that it had taken a reset to the factory defaults, because the power on option had changed.

  • Problems with msi p35 neo 2

    Default problems with msi p35 neo 2
        pc works fine when using windows and the net and emails
        only when using 3d mark or games do i ever get problems
        just help in getting the hole story 6 months ago got a msi neo2 install all my old components core 2 duo 4 gig ram form a diffrent board works fine but never used it playing games just used for the net and email shoping seamed to work fine but
        tryed playing a game 2 months later command and conquer 3 pc was some times freeze or graphics artefacts on screen assumed vga card faulty got another graphics card geforce 8600gts installed still the same in the last month got round to playing with the pc again and installed new g7 780 watt power supply and ati hd 4870 graphics card
        now i can use 3d mark some times it will go through once or just freeze or 3d mark stops the test
        temps on the board (from msi dual core center temps cpu 33oc system 47oc)
        memory voltage 2.1
        any one know the settings for the ram
    more details you need
    System Details
    MotherboardEdit Value
        msi p35 neo2 fr
    Motherboard BIOSEdit Value
        latest
    CPUEdit Value
        core 2 quad 6600
    CPU Overclock SpeedEdit Value
        none
    CPU HeatsinkEdit Value
        standard intel that come with cpu
    CPU Idle TempEdit Value
        N/A
    CPU Load TempEdit Value
        N/A
    MemoryEdit Value
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
    Memory VoltageEdit Value
        N/A
    Video Card(s)Edit Value
        ati hd4870
    Video Card SpeedEdit Value
        N/A
    Sound CardEdit Value
        onboard
    PSUEdit Value
        g7 780 watt power extreme
    Hard Drive(s)Edit Value
        mator dimondmax 21
    Optical Drive(s)Edit Value
        N/A
    Other CoolingEdit Value
        3 80mm fans 1 frount 1 back 1 side
    ModsEdit Value
        N/A
    Operating SystemEdit Value
        windows 7

    Quote
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
       Quote
    memory voltage 2.1
    Make sure that the memory timings are not set to 4-4-4-x but that they are set to the defaults values (5-5-5-x).  Also ensure, that the memory clock speed is not set to anything higher than 400 MHz (=DDR2-800).  The voltage at these settings should not need to exceed 1.95V.  So please lower it accordingly.  In case the freezes still occure, please run memtest86+ to check your memory for errors.
    Quote
    msi dual core center
    Please get rid of that tool for all further tests.  Uninstall it completely from your system as it is known to cause crashes and freezes on its own terms when running.

  • I had a major problem with my PC yesterday, and subsequently lost Mozilla Foxfire. When I reloaded it onto my PC it opened up with "Welcome to AOL - Mozilla Foxfire". I don't want AOL attached or tagged to Foxfire. How I do prevent that? And hopefully I h

    I had a major problem with my PC yesterday, and subsequently had to reload Mozilla Foxfire. When reloaded, it opened with "Welcome to AOL - Mozilla Foxfire". I don't want AOL associated or tagged with Foxfire. I went in to "Programs and Files" and deleted everything with AOL, including Quicktime. Tried loading Foxfire again, but it still opened with AOL tagged. I do use AOL for emails and some browsing, but I want to use Foxfire soley for browsing and search engine. And yes, I did also reload AOL. Can't seem to figure out why AOL is tagging onto Foxfire. Hopefully I have not lost all of my Foxfire Bookmarks - that would really suck.
    == User Agent ==
    Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; .NET CLR 1.1.4322; InfoPath.2; .NET CLR 3.5.30729; .NET CLR 3.0.30729)

    Hello Larry.
    Hopefully this support article is what you need:
    http://support.mozilla.com/en-US/kb/How+to+set+the+home+page

  • [Athlon64] Problem with MSI RS480M2-IL

    Hi all,
    I have problem with MSI RS480M2-IL. My problem is My temperature is very high... around 55-60c ... i am using AMD 3000+ Venice and no OC... and SpeedFan unable to detect my Voltage usage... Aida32 also same... 1 more thing is when i tried to run SiSoft Sandra 2005... it will take alot of time to load, sometime will just hang. i Test PCMark04 and found only got 3k for average mark... my friend getting 4k+ and we are using same spec... Below is my Spec:-
    MSI RS480M2-IL
    AMD 64 3000+ Venice E3
    Bios Version 3.8
    Geil PC3200 DDR400 2.5-3-3-6
    Maxtor 60GB HDD 7200RPM 2mb
    Verudium Power Vortex 420W
    Hope some one can advised me what to do... my score too low and my board detect temperature and voltage is not accurate... Hope MSI Engineer will look thought and help me... Thank for Viewing !

    the underlying "Who's fault is it?" question: AMD64 VENICE CORE (E3) PROCESSORS? or MSI RS480M2-IL MOBOS?
    so far, ALL users with this proc/mobo combination HAVE the high (or incorrect) temperature issue. replacing the mobo obviously will not resolve the issue but replacing the proc with one that is NOT a Venice E3 core, does the trick. but of course, not everyone will have the privilege of exchanging their damned proce via the retailer specially if it's beyond the first 21 days of purchase.
    in my case, my retailer refused to have the E3 proc replaced with the 'corrected' E6 version no matter how hard you explained the known issues with the E3. no chance of AMD recalling the E3 cores since problems with are only isolated to the particular MSI RS480M2 boards.
    so for users that are and will be stuck with this combination, what is the solution then to the temperature issue? in my opinion, it's up to MSI to perhaps release a bios update that will correct this. another important thing to consider is the question: IS MY VENICE CORE INDEED OVERHEATING OR IS IT JUST THE MSI MOBO SHOWING INCORRECT READINGS? the proc overheating in actuality is obviously a lot different thatn just having an incorrect bios temp readings.
    based on what i have observed, my Venice core displays the correct cpu temps (33-35*C) when being used on a MSI K8 Diamond mobo. placing the proc back to the R2480M2 board shows a very unusual 61-63*C bios cpu temp. furthermore, if i touch the stock heatsink/fan cooler that i have (for both motherboards), it really does NOT seem to be extremely  hot to think that the cpu is actually overheating. in addition, my system using the RS480M2 performs well and has no spontaneous shutting down problems whatsoever. of course, my sense of touch is not as accurate as a thermometer but more or less, if you consider all the points i mentioned, most of us can say that the whole issue is just a matter of incorrect cpu reading.
    perhaps the ATI chipset is the one to blame since i have notices as well that the Venice core processors do not seem  to have this high temp problems with MSI's K8 mobos with the NVIDIA chipsets.
    one last question: so do you guys think that this problem can be resolved by a simple bios revision? (as a dell tech guy, i do know for a fact that bios updates resolves overheating error messages in Inspiron/Latitude laptops) 

  • I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies

    I am experiencing some major problems with my MacBook Pro. I have had some issues with it turning on/off at random times, but today, when starting, I get the grey start-up screen and a recovery bar. After filling in approx 1/4 of the way, the machine dies. After starting it in recovery mode, it will not allow me to download OS X Mavericks- it says the disk is locked. Any ideas? I do not have a back-up and do not want to erase everything before I have explored my options. Help?

    try forcing internet recover, hold 3 keys - command, option, r - you should see a spinning globe
    most people will tell you to do both pram and smc resets (google) and if you still have issues, either clean install (easy) or troubleshoot (hard)

  • 10.9.3 = major problem with fast user switching

    I've found a major problem with the 10.9.3 update with my 27" iMac, you probably won't see it if your on a laptop. I did all the updates in past few days i.e., 10.9.3 combo update, iTunes 11.2.1.
    Afterward I noticed a bug when Fast User Switching i.e. FUS. I have 5 accounts but the bug can be replicated with only 2.
    I login to userA  have some windows open but you can just open a Finder window. Now make the window at least half the with of the screen and move it to the right side of the screen. Then login in to userB and setup the windows the same way as userA. Now FUS to userA and then back to userB. You will notice that the Finder window has been moved to the upper left corner of the screen. This problem happened's to all user accounts you login to except the first account you logged into.
    Since I didn't know what update caused the problem I had to use Time Machine to revert to my last version of 10.9.2. I then double checked the for the bug and sure enough everything was working fine. I now was going to install one update at a time and to see which one was causing the bug. So I installed 10.9.3 first and found the bug immediately.
    I now know what's happening. When the switch occurs the screen is resized to about the equivalent of a 13" MBP. At this point the windows that fall some ware outside that size get moved to the upper left corner and resized. Then the screen resizes to normal but it's too late, all the window have moved and been resized to fit the 13" screen size.
    You can reproduce this effect by going to System Preferences and selecting Display and then select the Scaled radio button. No select the smallest size, say, 1280 x 720. Now select the Best for display radio button again. You will now see all the windows you have open that were too big no moved and resized to the upper left corner. I know why the Mac moves the windows, it's so you don't have any windows stuck off screen.
    Now when I say 13" it could be some other size but it's about that size give or take.

    Yes, it's when you user Fast User Switching.
    Here's snapshot before the screen resized. Ignore the window in the lower right, I moved it from the upper left before taking the screen shot.
    I hate to say it but I'm glad I'm not the only one with this bug.

  • I am having major problems with my trackpad on my macbook pro.  I can no longer press down on the bottom left and right corners for it to click and follow my command.  Please can anyone help?

    I am having major problems with my track pad on my macbook pro.  Even though my settings haven't changed...my trackpad is no longer responding as it did before.  The left hand corner no longer clicks when I press it and my personal commands which I set up in preferences no longer seem to be workin.  Please help!

    Some websites have an internal mute or volume setting. If that's not the issue, see below.
    From the Safari menu bar, select
              Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data...
    and confirm. Close the window. Then select
               ▹ System Preferences… ▹ Flash Player ▹ Advanced ▹ Delete All...
    In the sheet that opens, check the box marked
              Delete All Site Data and Settings
    then click Delete Data. Close the preference pane.

  • Major problems with Premiere CS4

    Hello there!
    I'm having major problems with CS4. I recently bought a new computer - essentials are as follows:
    Intel Core i7 920 2.66GHz
    2 x Kingston 3x2GB, DDR3 1333MHz (=12 GB RAM)
    Ati Radeon HD 5770 v2
    Asus P6T SE, LGA1366, X58, DDR3, ATX
    2 x 500GB, Barracuda 7200.12 (RAID1), system disk
    2 x 1TB Barracuda 7200.12, media disks
    Windows 7 Pro 64 bit
    Adobe CS4 Production Premium + latest updates
    The problem I have has mostly to do with Premiere although I think the rest of Production Premium softwares should be running better on this computer as well.
    For starters, I was highly disappointed when I couldn't view a single HD clip from the Premiere timeline (it was an .m2ts rip from a previously self-burned Bluray disc) at all. Rendering is very slow and even after that the video doesn't run normally, showing just a few individual frames per second. When I point the timeline at a certain spot, it takes many seconds until even that very frame is shown in the monitor window.
    And this is not all - I decided to try with a basic DV AVI clip, previously captured with my PPro 1.5 on my earlier computer (3.2ghz Pentium from 2005). It's a native file so it doesn't even need rendering and still the same problem occurs. With normal playback only about 6-10 frames are shown per second. It's absolutely ridiculous - even my 2004 laptop runs DV AVIs more smoothly with PPro 1.5.
    While I'm running the Premiere, the level of used RAM comes only up to around 24 percents. The processor, then again, comes close to a hundred when play is pressed on the timeline.
    I haven't had such immense problems with other Production Premium softwares (though as I said, I think they should be running faster as well). Otherwise the computer is running smoothly.
    A friend of mine pointed out that the graphics card I'm using isn't on the Adobe website's list of supported ones with Premiere, but afaik it shouldn't even be a graphics card problem with this high-end machinery.
    So - I sure could use some help and ideas about how to get the Premiere working. My main intention for buying a new computer and Adobe CS4 Production Premium was to start HD editing after all! Thanks beforehand!

    Hi
    Yeah, I hope he solves problem and knows how it got solved and tells us all...it's like being a detective !  " Mr Plum did it in the "svchost" room ! "
    I got a little lost on this....
    You are welcome and I'm glad that it paid off so nicely for you. One more  suggestion, if I may: I'm a big fan of a fixed pagefile size. When making a  fresh install of Windows, one of my first actions is to set a fixed pagefile on  a different disk (min=max) before installing anything else on that different  disk and removing the pagefile on the C drive. This will ensure that the  pagefile in on the fastest part of the drive and will never be  fragmented.
    I think it used to be that I made swapfiles, or swapdisks which now seems to be called pagefile.  That in itself is a little confusing semantic wise, because of the use of mempage stuff.  It used to be that base memory was 640k, with the upper memory (to make up 1024 kb) was mostly for drivers and stuff.  If more memory was needed than 640k (an event the inventor never thought possible...  "who could want more than the enormous amount of 640K ?", he said..)..the extended and expanded memory got invented to swap memory pages from that 640k as needed with the rest of RAM.  That's basically correct right ?  Sooooo, I don't know if that still goes on, but I suspect it does, unless someone totally changes the architecture of the computer and cpu and fsb and everything...  but I don't know what is going on nowadays.  Anyway, there were other ways besides windows OS to create virtual memory on the hard drive, and Photoshop was one of the programs that could do that, I think.
    Why MS would want to call the swapdisk virtual memory "pagefile" is beyond me.
    Anyway, be that as it may, I understand that making the pagefile first on a drive so it's close to the center of the drive (heads don't have to travel far to access).  But I haven't added a lot of drives to a system before, and I suspect I will be pretty soon...and this is the part I don't get...
    You add drives and put OS on them?  So they are bootable ?  I've added a drive or two but just formatted and used as more storage but didn't put OS on them.  So that part is confusing...
    Then you take the pagefile off the C: drive ?  Are you then using the new drive as your boot drive and the C: drive is too full to use accept to run the programs already installed ?
    Thanks again !
    Rod

  • Major problems with CS5

    We just moved to CS5 and are having major problems with crashing and losing text. I haven't seen these kind of issues since beginning the Indesign/Incopy workflow way back in CS2. I've got dozens of users (Indesign and Incopy) slamming me with complaints of crashing. Indesign crashes when exporting to Incopy (usually when exporting a layer), Incopy users are complaining of crashing when peforming copy/paste either from Word or from within Incopy. Also have had incidents where the text in the Incopy story just disappears or the stories corrupt and will not open in the layout or as a standalone file. Trying to open one will crash the application.
    Other departments in our organization who do not use Incopy are not experiencing crashing issues with Indesign CS5, so I have to believe the problem is Incopy.

    Try moving everything to a local harddrive and working on a file there. If you don't get the crashing then you can start checking the network. And please, one thread is enough.
    Bob

  • Really weird problem with msi 815ep pro

    hi all i have searious problem with my sweety motherboard everything should be ok but its not .. the leds are showing that all simm to be fine (4x green) but i cant install any os (linx,windows) its funny cause when i had hdd 850mb windows98 installed perfectly or when i repair a disk everything goes ok i changed disk for known reason (capaticity) to seagate 2,5gb also tried with 120gb and 4,3gb but nothing after starting the instalation its hang up i tried everything i changed processor, ram, hdd connectors, graphics card, cd-rom also switched off integrated audio and others like midi, usb... and still nothing i do not have any more ideas i dont know what to do    i've noticed that few capacitors have minimal belly on top could it be this or what else maybe hdd controller is broken ? how do you think i also cant flash bios to older version dont know why... please help me   

    i've got it those were capacitors !!    i wouldn't expect that but it was my last chance i changed 4 capacitors and really they weren't soo much belly on the top now my motherboard my sweet honey yelly works perfect      hehe greetings for everyone
    love rules !

  • I bought an iphone 5 in the United States. It has major problems with the video. In Italy not fix it. What am I to do?? back in the United States

    I bought an iphone 5 in the United States. It has major problems with the video. In Italy not fix it. What am I to do?? back in the United States

    The iPhone warranty is not international. If you bought it in the US you can only get service in the US. You will need to take it in to an Apple store in the US.

  • Anyone else having major problems with Safari 5.1 on Snow Leopard?

    is anyone else having major problems with Safari 5.1 on Snow Leopard?
    - address bar and search box are not resizing with browser window. the address bar and seach box set their size to the window when Safari is launched and remain that size.
    - anytime i try to customize toolbar items disappear and i have to restart Safari to get them to appear.
    - some 3rd party icons just remove themselves from the toolbar after a period of time
    - when i drag a page from the tab bar to create it's own browser window the window disappears but is listed in the windows menu bar. when i select that window from the menu bar the window appears but i can't click on anything.
    I've repaired permissions numerous times, reinstalled safari numerous times and restarted my machine numerous times and the issues all remain. i've never had any issues with Safari until now and 5.1 is looking like a huge mess.
    besides the bugs above, has anyone had any luck with 1password working with Safari 5.1?

    ok, i narrowed most of my issues down to Web Snapper and Videobox by TastyApps. Removed both of those and now everything works better.
    I went out to lunch and came back an hour later and magically ALL of my previous toolbar icons that were added to my previous version of Safari appeared. Very strange.
    as for 1password, it wasn't working at all before when i posted. everytime i tried installing the extension via the app my, Safari would open a window and hang (never load). I just tried it again and it seems to now be working.

Maybe you are looking for