Managed system user locking because of solman_setup wrong information

Hello,
Each time I go to solman_setup -> Managed system,
there are two systems with a red point because of non
working rfc connection.
When I reconfigure them (3. connect managed system), I change the
user/password to connect to the managed system.
But our solman still connects to the managed system with the wrong
username and password.
Then the user is locked in the managed system (too many connections with a wrong password),
How could I proceed to tell solman to stop using the old username
password provided?
Regards,

Hello Beniot,
I has similar issue some time back, please have a look at below link.
RFC error in third step while performing managed system configuration
reset the password and retry, and try to check dump in both the system, solman and system which you are trying to do manage system config.
Even after this you are getting error, please paste the screen shot or attach the error.
Regards,
Haseena

Similar Messages

HT201274 my phone is lock because i prees wrong password more than 10 times

My phone is lock because i prees wrong password for more than 10 times. I can open my phone what should i do?

Open iTunes on computer, connect iPhone to computer with USB cable. Hold both Home and Power buttons on iPhone until iTunes recognizes iPhone in Recovery Mode. This usually takes about 20 seconds of holding both buttons. Restore the iPhone Firmware. At the end Restore from your iTunes Back-Up or use iCloud to get your data back.

"System" user locked

Hello all. For entering in Oracle 10g Db we start SQLPLUS. user-name "system" and
password containing @ (my mistake), TNS error view. Presently I know that problem
in "@" symbol. While understood the user "system" is locked....
As possible change password and unlock the user?
Or create the the new user for Oracle....
Please advise ....

ups,
I forgot that part, we are giving the answer in small pieces
Resume for "dummies"
1) Connect to the database
sqlplus "/ as sysdba"
2) Unlock the user ( as William Fee post )
ALTER USER xxxxx ACCOUNT UNLOCK;
3) Change the password ( as my post )
Alter user system identified by <newpassword>
4) a bit optional ( IMHO ) change the profile ( as William Fee post )
ALTER PROFILE DEFAULT LIMIT FAILED_LOGIN_ATTEMPTS UNLIMITED;

HT1212 my iphone is lock because of entering wrong password

my iphone is lock because of wrong entering password

marites rosales wrote:
my iphone is lock because of wrong entering password
If you cannot remember the passcode, you will need to Restore the device...
1) Connect to iTunes on the computer you usually Sync with and Restore...
http://support.apple.com/kb/HT1414
2) If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/HT1808
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup
http://support.apple.com/kb/ht1766

CAM giving error "Locked because of execeeding wrong password attempts"

Hello,
I ahve a 6140 managed through CAM. While discovering I have used a wrong password by mistake for 2-3 times. I have the array now registered with the right password. When I try to update the firmware, I am getting an error message " Locked . exceeding wrong password attempts".
Kindly help me in unlocking the 6140 in CAM so that I am able to upgare the firmware on it.
Many thanks in advance
Ushas Symon

A while ago I had the same problem. I restarted CAM and I could go on with the upgrade.

My ipad is locked because of multiple wrong pin codes. how to fix?

how to unlock ipad when multiple wrond pin codes were entered ?

If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad/iPod into Recovery Mode
http://support.apple.com/kb/ht4097

My apple account is locked because i entered wrong anwers on security questions. What should i do?

Help please!

You need to contact Apple to get them reset. Click here, phone them, and ask for the Account Security team, or fill out and submit this form.
(93379)

Document Management System(DMS)

Dear Expert,
We need to store the Employee revision letters( in PDF format) in DMS. Letters are currently in HTML format which we will convert them in to PDF format & store the same thru Document Magement System (DMS).
I would like to know,
1. How can we use DMS to store the letters in PDF format?
2. Where can I find DMS configuration part in SPRO?
3. I understand that DMS is a unique concept availabe in SAP HR. So how can I link DMS to HCM?
4. Is SAP Archive link related to DMS ?
5. Any documents/links related to this kinldy send it across.
Thanks in Advnace,
Regards,
Damodar Pai.

hi
try with this
SAP DMS - Document Management System
SAP DMS are for storing documents such as CAD drawings, Materials pictures etc.
With the document management system, users will be able to view the documents with ease within their SAP systems.
Installing the SAP DMS requires a little bit of planning on how you want to do it.
You have to give a little thoughts to stuff such as :-
1. The total numbers of documents that will be store monthly.
2. The average file size of each documents.
3. The capacity of your present R/3 system.
4. Your present network bandwidth.
5.   Document Archiving Strategy.
6.   Backup and Recovery Plan.
Additional purchasing of hardware are required, especially if you have large amount of documents to stored.
With this in mind, you can then decide on how you want to do it.
You can do this in a few ways :-
1. Import the documents into the R/3 system.
2. Use an external document server.
3. Have a dedicated PCs where all the documents are stored.
Most companies that intend to used DMS will opt for Option 2 as they does not want to overstretch the R/3 database.
Options 1 requires you to setup the conversion interface.
The conversion interface allows R/3 to automatically covert your files and import it into the R/3 database.
Here is a simple example of storing documents into your PCs, just to have a feel how the SAP DMS works:-
For those using Citrix, you have to set this at the Citrix Server where the SAPGUI is located.
Configure SM30 - V_TDWE_C1
Put this command in your autoexec.bat
SET HOSTNAME=PC1234
Restart your pc.
You can create/manage your documents in transaction code CV01N / CV02N
Assigning Documents to a Material Master Record
Access a material master record in Create or Change mode, and select Basic Data.
To create links to documents, choose Additional data -> Document data.
The Link to Documents dialog box appears.
Assign one or more documents to the material.
If you do not know what the document number is, you can search for it using the search help or by choosing Find document.
When assigning a document to a material, you have the following options:
1. Viewing the document by choosing it in the Link to Documents dialog box.
2. Viewing any originals of the document by positioning the cursor on the document and
   choosing Display originals in the Link to Documents dialog box.
To return to the Basic Data screen, choose Continue.
Save your data.
all the best
madhu

Managed system configuration: Some required roles have not been granted

Hi experts,
I face a strange problem in my SolMan 7.1 SPS 4:
In the configuration of managed system everything is green except the last step "Check configuration" => "Configuration Check".
The error is:
Some required roles have not been granted to user SAPSUPPORT (ID: MANAGED.DUAL.SAPSUPPORT)
Action: Execute step Managed System Configurationn / Create Users
Check Context: Managed systems users/roles | Managed users/roles | SYSTEM =LSM~ABAP
and the same for SMDAGENT_xyz (ID: MANAGED.ABAP.WILYAGT).
The funny thing is that the step no. 7 (Create users) is done successfully. I have also deleted SAPSUPPORT manually and have reexecuted step 7 but no success.
Any ideas? Thanks and best regards, Basti

Hello,
Just a thought... it could be due to a UME role that is not assigned to the user. Have you checked the security guide?? There are a couple of steps to do in Visual Admin for this use as per the guide.
Cheers,
Diego.

How to save ALV extract to document management system

Hi all,
i have a requirement of saving the alv extract to DOCUMENT MANAGEMENT SYSTEM. Could any one of you please help me out in giving a solution to do this.
Thanks in advance.
Kiran

Hi
check this
SAP DMS - Document Management System
SAP DMS are for storing documents such as CAD drawings, Materials pictures etc.
With the document management system, users will be able to view the documents with ease within their SAP systems.
Installing the SAP DMS requires a little bit of planning on how you want to do it.
You have to give a little thoughts to stuff such as :-
1. The total numbers of documents that will be store monthly.
2. The average file size of each documents.
3. The capacity of your present R/3 system.
4. Your present network bandwidth.
5.   Document Archiving Strategy.
6.   Backup and Recovery Plan.
Additional purchasing of hardware are required, especially if you have large amount of documents to stored.
With this in mind, you can then decide on how you want to do it.
You can do this in a few ways :-
1. Import the documents into the R/3 system.
2. Use an external document server.
3. Have a dedicated PCs where all the documents are stored.
Most companies that intend to used DMS will opt for Option 2 as they does not want to overstretch the R/3 database.
Options 1 requires you to setup the conversion interface.
The conversion interface allows R/3 to automatically covert your files and import it into the R/3 database.
Here is a simple example of storing documents into your PCs, just to have a feel how the SAP DMS works:-
For those using Citrix, you have to set this at the Citrix Server where the SAPGUI is located.
Configure SM30 - V_TDWE_C1
Put this command in your autoexec.bat
SET HOSTNAME=PC1234
Restart your pc.
You can create/manage your documents in transaction code CV01N / CV02N
Assigning Documents to a Material Master Record
Access a material master record in Create or Change mode, and select Basic Data.
To create links to documents, choose Additional data -> Document data.
The Link to Documents dialog box appears.
Assign one or more documents to the material.
If you do not know what the document number is, you can search for it using the search help or by choosing Find document.
When assigning a document to a material, you have the following options:
1. Viewing the document by choosing it in the Link to Documents dialog box.
2. Viewing any originals of the document by positioning the cursor on the document and
   choosing Display originals in the Link to Documents dialog box.
To return to the Basic Data screen, choose Continue.
Save your data.
Regards
Anji

Oracle BPEL Default System Users

Hi all,
Oracle BPEL Process Manager system users default, bpeladmin, guest and seventeen other Oracle BPEL Process Manager users
where do i find them exactly and how to access them?
Regards,
- sri

Thanks every one for answering so fast.
Srini,
what you suggested was just perfect,Thanks.
Secondly do you a list of default roles and default profiles.that would be great.
and is there a script to do a complete clean up of the db .so that it sets up like a new db without removing the tablespace only?
I have started the imp on the db - i Googled out some list of default oracle users, but ur list will definitely come in handy.
Thanks again everyone specially srini
Anto

Managed System Configuration Super User Issue

Hi folks ,
I have a strange error in Solman SP8 Managed System Config .
In Step 5 : "Enter System Parameters" , for entering super user , it throws an error even though the user credentials are valid.
This happens for some of the managed systems only . The error says : " Issue with connection to system <SID> <Client>".
It does not seem to be using the right RFC and I feel it is checking for the user in 000 client , regardless of which client we give . Because if we give 000 credentials it works.
Please help . As without this I cannot save any of the system parameters like Load Balancer URL etc.
Thanks,
Shaswat

I have seen this exact issue when my IE cached the page and was stuck with the client 000 RFC's selected on step 3. I just exit managed sys config and clear my cache and start solman_setup again. To avoid this all together I set my IE to check for newer versions of stored pages every time I visit page. (under internet options -> general -> browsing history -> tempory internet files)
Then
In step 3 create the user to avoid security issues or auditor problems later on. This way the SM_ADMIN_XXX will have the proper roles required. Please note (The user is not authorized to use a Trusted RFC (authorization object S_RFCACL). To authorize the user, assign the role SAP_SM_S_RFCACL manually).
Confirm there is no error and hit next. For an explicit save.
Now go to step 5 and select the client that the RFC's were created on and hit test credentials.
This should solve your issue.

SOLMAN_SETUP - Managed System Configuration - DBA_COCKPIT

Dear SAP Colleagues,
I am currently implementing SMD in my Solution Manager system. I use the guided procedure SOLMAN_SETUP. The first 2 phases - Initial and Basic Configuration are completed.
I have starting the 3rd one - Managed System Configuration - Manual Configuration.
I have started the "Configure DBA Cockpit".
I have no problem with most of my managed systems (ERP, BI, EP)..
But when I want to configure the DBA cockpit for my PI systems, I get error.
Even if I personnaly there is nothing to do with the SAP Product, I get an error when I want to configure my all 3 PI system in DBA Cockpit.
1. I select the Managed System in my list
. The DB Host Name is automatically filled out.
. The DB Name is automatically filled out.
. The Schema Name (Optional) is also automatically filled out.
2. Then I click on Next button and I get this error :
The DB connection is no successfully tested.
Please make sure the parameters below are correct and hit ....
Database Name : XDS
Datbase host : xdsci
TNS Name : ???
User Name : SAPXDS
Password : ???
Question :
1. From where (SLD or SMSY) these information (Database Name, Database Host, TNS Name ...)
related to managed system XDS are uploaded ?
In other terms, where are these technical information pre-configured ? In SLD ? In SMSY ?
2. How may I fix this issue ? I did not configure the other managed system and it perfectly works.
Thanks in advance for your help
Best regards
CP

Hi,
I found this OSS Note : 1265070
You can also connect directly to this link :
https://websmp207.sap-ag.de/~sapidb/011000358700000074392009E
Best regards
CP

SOLMAN_SETUP - managed system configuration

I am attempting to use the SOLMAN_SETUP transaction to establish the managed system connections to my ABAP ECC systems. I enter the required user/password info and execute it. I get one error message in the log that says "Cannot get fully qualified name of the server as400q3". The as400Q3 server is the host where the managed system resides. I do not know where to fix this issue.
Best regards,
Russ

Hi ,
You have to mention it in Txn. SMSY- Server->as400q3->Fully qualified host name.
Also, Please make sure the host file entries are maintained correclty on your solman server.
Hope this helps.
Kindly revert if you face any issues.
Thanks,
Jagan

PHP user management system

I have been using an ASP based user management system with an
Access
database and it has worked very well, however, I need to
implement a similar
system on a Linux server. I know you can password protect
sections of the
site using htaccess but I want something similar to what I
get with the ASP
system, ie user reg page and redirection pages for those who
enter wrong
details, duplicate usernames, password recovery, etc. Nothing
fancy, just
the basic functions to allow people to access restricted
areas of the site.
No payment will be involved, my client just wants to limit
access to certain
parts of the site to registered users.
Can anyone recommend something simple and easy to setup and
use? Either a DW
extension or standalone, bearing in mind I don't know PHP but
I can edit
code with a little guidance...
Many thanks in advance

DW has User Authentication server behaviors built in, you
know?
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
==================
"polarl light" <[email protected]> wrote in message
news:g166m7$gvt$[email protected]..
>I have been using an ASP based user management system
with an Access
>database and it has worked very well, however, I need to
implement a
>similar system on a Linux server. I know you can password
protect sections
>of the site using htaccess but I want something similar
to what I get with
>the ASP system, ie user reg page and redirection pages
for those who enter
>wrong details, duplicate usernames, password recovery,
etc. Nothing fancy,
>just the basic functions to allow people to access
restricted areas of the
>site. No payment will be involved, my client just wants
to limit access to
>certain parts of the site to registered users.
>
> Can anyone recommend something simple and easy to setup
and use? Either a
> DW extension or standalone, bearing in mind I don't know
PHP but I can
> edit code with a little guidance...
>
> Many thanks in advance
>

Managed system user locking because of solman_setup wrong information

Similar Messages

Maybe you are looking for