Management port in Cisco Switches (are they really physical port)

Hi all,
I have been taught to console into my cisco switch for configurations through console cable + putty (serial terminal).
Then I have been taught to configure a management ip and gateway on the cisco switch.
Switch# conf t
Switch(config)# interface vlan 1
Switch(config-if)# ip address 192.168.1.11 255.255.255.0
Switch(config-if)# no shut
Switch(config-if)# exit
Switch(config)# ip default-gateway 192.168.1.1
All the while, i thought this is the way to remote in to the switch via putty/telnet through the network to configure the switch, until i saw the picture below (cisco catalyst 2960)
=======================================
There is a physical port call ethernet management port. What is it ? What is the difference between this port and the earlier example of setting a management ip in VLAN 1 ?
If i set an IP on this particular interface and I ssh in, will i see the same screen/display/console from the earlier example in which i set a management ip in VLAN1 and I ssh in ?
Regards,
Noob

Hi Leo,
Sorry if you find it hard to explain to me.
I have understood to think of the ethernet management port as a separate entity from the original switch.
Maybe with the help of the diagram below, can you let me know if i have understood correctly ?
*please assume connected port is a management port separated from the normal switch ports
q1) does the ethernet management port need to be connected to another switch ?
I have thought of it as a device on the network and it is mentioned by you previously that it will be connected to a switch
"he traffic goes up the cable connected to the Management port and up a switch. Now that switch holds all the information because it is a switch. "
q2) In the current setup then, terminal B will be able to access the management port - am i right ?
q3) you mentioned that the management port is not able to set any gateway, (which is the router fe0/5 - 192.168.0.3 in my illustration), in that case do you mean that terminal A will not be able to access the management port remotely and it can only be accessible locally ?
Please do correct me if my understanding is wrong.
Thank you so much for your advices.
Regards,
Noob

Similar Messages

Yosemite 10.10.2 server app. FTP help. I have a program running in my local server enviroment that wants to FTP to my mac folder. It asks for the server , name, password, port and path. what are they?

So I have set up a localhost area in my Mac. I have the new server.app and I am running yosemite 10.10.2 .
I have a program running in my local server enviroment that wants to FTP to my mac .
It asks for the server , name, password, port and path. what are they?
I am pretty certain that the Serveris "localhost",
Name is my macs name (like my-mac-min)
password is "my login password"
and they suggest port 21.
But what is the file path, lets just say my site is set up http://localhost/siteftp and is actually at my Users/Sites/siteftp folder.
Why cant this program connect to the mac.
Is it because they are both operating in the same localhost enviroment,
could it be my folder permissions are not correct on siteftp folder?
Help please !

I tried turning the computer off and then back on. The alerts don't show the notice to update as resolved. Hopefully this is not a problem or an indicator or another problem. Should I ignore or reload 10.10.1 from the app store to trigger a resolved check in a green circle?
Interesting that I had to buy server software after my free Yosemite download. I would have hoped that the two pieces of software would have gone together without any complication. It is not positive to end up buying a problem. Ah well, time to move on.

Changing SSH port in Cisco switches

Hello everyone
I have switches with different platforms 2950 , 3750 , 3560 ...... I want to change the port of SSH , but the command ip ssh port not found ... be informed that the IOS is ipservice type for layer 3 switches

Sorry but you cannot change the port (tcp/22) used by ssh on Cisco switches.
The best practices for securing it it include:
- enforce ssh version 2,
- apply an access-list to your vty lines,
- set a timeout and retry lockout, and
- possibly control plane policing.

Cisco switch 300 configure vlan and ports

Hi i need help
i cant see the vlan on port vlan membership
i did create the vlan and i did configure the port the access
but when i try to port vlan membership to tell which port to wich vlan i cant see the vlan i have created in the list
thanks to help

Hi,
This forum is focusing on the issues related Windows Server.
To get better help, please post your question on the forum of cisco.
Here is the address,
https://supportforums.cisco.com/
Best Regards.
Steven Lee
TechNet Community Support

Imessages showing as delivered. Are they really being received

I am just curious as to if the person I am sending the message too, and they don't have the "read notification" turned on, if my messages are really going thru even though they say delivered? Does that make sense?

"Delivered" tells you that they were delivered to that Apple ID/phone number. It tells you nothing else. I have never had any reason to doubt the accuracy of "Delivered". If the person you're messaging doesn't want to turn read norification on, that's as much information as you're going to get.

Can't contact Adobe... Are they really that unprofessional?

I'm a Camtesia Studio User and I am looking at
converting over to Captivate. The software continually crashes on
me. It is a trial version that I have just downloaded. I understand
that things like this happen and I am not so upset about that. I am
however rather frustrated that I cannot seem to even send Adobe an
email about how to fix the problem.
Here is the problem...
The software crashes sometimes upon opening a new project.
The software crashes everytime upon ending a recording. In my
search I found another person with the same problem. One user
responded with suggestions. I followed those suggestions to no
avail. I have uninstalled the software... cleaned up my system and
reinstalled to no avail.
So I would think that my next course of action is to contact
Adobe and ask.... "How can I get your software to work?".
45 minutes of searching Adobe.com and I can't find anyway of
contacting them to ask such a basic question.
Am I missing something? Is Adobe really that
unprofessional?

The contact method has been supplied though I agree they
could make it
easier - one thing Adobe said they looked forward to with the
Macromedia
integration was the community relations Macromedia brought to
the table.
It seems that aspect of the integration hasn't been all that
successful
so far...
Anyway, Captivate crashes as you describe I would suspect
being a result
of video card issues. Try adjusting the Troubleshooting
slider (assuming
XP; Display Properties > Settings > Advanced >
Troubleshoot). Bringing
that down a notch or many may help the stability...though may
also
effect the quality of the captures.
HTH
Erik
westonweb wrote:
>
I'm a Camtesia Studio User and I am looking at
converting over to
> Captivate. The software continually crashes on me.
Erik Lord
http://www.capemedia.net
Adobe Community Expert - Authorware
http://www.adobe.com/communities/experts/
http://www.awaretips.net -
samples, tips, products, faqs, and links!
*Search the A'ware newsgroup archives*
http://groups.google.com/group/macromedia.authorware

Why is Keynote, Pages, Numbers, and iPhoto all under the free category in the app store but say they cost money? Are they really free? Should I download them?

HELP! I need these softwares for educational purposes ASAP! I'm not sure whether or not I should purchase any of them, due to the fact they are under the free category, yet if I click each app they all say to "buy now" for a certain price. This is questionable to me, and I am unsure what the real cost of them are before I attempt to make any purchases or not. If anyone could let me know soon please, that'd be great. Or if there are any other trust worthy sites for a free download that would be great too if you could just list the process THANK YOU! (:

All Apple computer come with the iLife suite of App totally free and they are installed on your Mac by the factory when it was built and shipped.
Those iLife apps are iPhoto, iMovie and GarageBand on Mac computers that came with any of the Download Only version of OS X, Lion Mt Lion and Mavericks and also include iDVD and iWeb on older Mac computers that came with OS X Snow Leopard or previous version of OS X.
If they are not already on your Mac then you can reinstall them from either the Mac App Store, for Mac's that came with Lion, Mt Lion or Mavericks, or from the Original System Reinstall DVD discs on older Mac that came with Snow Leopard or previous version of OS X.
You need to post what model year Mac you are using and whether or not you bought it new from Apple or an Autherised Apple reseller.
As for the iWork set of applications, Pages, Numbers and Keynote, those you need to buy from the Mac App Store unless you purchase your Mac New from Apple or an Authorized Apple reseller on or after October 21 2013.
So what model year Mac do you have and did you buy it new.

JDeveloper 3.1 and JDK1.2.2: are they REALLY compliant?

Hi,
I've already been developing in JDev 3.0 using Java 1.1.8 for a few months and have a number of EJB's deployed in an Oracle8i 8.1.5 database. These are accessed by a servlet which is called from a C++ application in order to populate the db tables. I'm using Java Webserver 2.0 and everything works fine.
I've been upgrading to Java 2 with JDev 3.1, Oracle 8i R2, and JDK1.2.2. Everything again works fine when I am testing and debugging in the JDev 3.1 IDE but when I deploy to the Web server, my context lookup for the EJB published name freezes, returns an error status to the C++ app but does not display any error/exception msgs in the server console/log files.
On investigating I found that the java.exe bundled with JDev 3.1 as the JDK1.2.2 version is actually NOT the java.exe that has been dispatched with the release version of JDK1.2.2! There are however two files in the bin directory of the JDK1.2.2 called oldjava.exe and oldjavaw.exe which correspond to the ones bundled with JDev 3.1?
Could someone please explain what is going on? As it stands at the moment the version of java.exe with JDK1.2.2 does not work for my EJB's but if I replace it with the oldjava.exe, it works fine. Does this mean that JDev 3.1 is NOT actually JDK1.2.2 compliant or have I done something wrong?
This is potentially a major problem for our projects so if anyone at Oracle has any info it would be greatly appreciated.
Cheers
Dave

David,
I changed Sun Java 1.2.2 VM to JDeveloper 3.0 1.1.8 VM and now I get this:
[Root exception is java.lang.ClassNotFoundException: EJBBibles.BibleSearchHomeHelper]javax.naming.Na
mingException: Unknown reasons
at oracle.aurora.jndi.sess_iiop.SessionCtx._activate(SessionCtx.java:82)
at oracle.aurora.jndi.sess_iiop.SessionCtx.activate(SessionCtx.java:276)
at oracle.aurora.jndi.sess_iiop.ServiceCtx.lookup(ServiceCtx.java:320)
at oracle.aurora.jndi.sess_iiop.sess_iiopURLContext.lookup(sess_iiopURLContext.java:215)
at oracle.aurora.jndi.sess_iiop.sess_iiopURLContext.lookup(sess_iiopURLContext.java:201)
at javax.naming.InitialContext.lookup(InitialContext.java:288)
at EJBBiblesServlet.Servlet1.init(Servlet1.java:36)
at org.apache.tomcat.core.ServletWrapper.initServlet(ServletWrapper.java:315)
at org.apache.tomcat.core.ServletWrapper.handleRequest(ServletWrapper.java:445)
at org.apache.tomcat.core.ServletWrapper.handleRequest(ServletWrapper.java:597)
at org.apache.tomcat.servlets.InvokerServlet.service(InvokerServlet.java:257)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at org.apache.tomcat.core.ServletWrapper.handleRequest(ServletWrapper.java:503)
at org.apache.tomcat.core.ContextManager.service(ContextManager.java:559)
at org.apache.tomcat.service.http.HttpConnectionHandler.processConnection(HttpConnectionHand
ler.java:160)
at org.apache.tomcat.service.TcpConnectionThread.run(SimpleTcpEndpoint.java:338)
at java.lang.Thread.run(Thread.java:466)
If I use JDev 1.2 VM, I get this:
javax.naming.NotContextException: fumaca:2481:eatg/test/BibleSearchRemote
java.lang.Object oracle.aurora.jndi.sess_iiop.sess_iiopURLContext.lookup(javax.naming.Name)
java.lang.Object oracle.aurora.jndi.sess_iiop.sess_iiopURLContext.lookup(java.lang.String)
java.lang.Object javax.naming.InitialContext.lookup(java.lang.String)
void EJBBiblesServlet.Servlet1.init(javax.servlet.ServletConfig)
void org.apache.tomcat.core.ServletWrapper.initServlet()
void org.apache.tomcat.core.ServletWrapper.handleRequest(org.apache.tomcat.core.Request, org
.apache.tomcat.core.Response)
void org.apache.tomcat.core.ServletWrapper.handleRequest(org.apache.tomcat.core.HttpServletR
equestFacade, org.apache.tomcat.core.HttpServletResponseFacade)
void org.apache.tomcat.servlets.InvokerServlet.service(javax.servlet.http.HttpServletRequest
, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.Serv
letResponse)
void org.apache.tomcat.core.ServletWrapper.handleRequest(org.apache.tomcat.core.Request, org
.apache.tomcat.core.Response)
void org.apache.tomcat.core.ContextManager.service(org.apache.tomcat.core.Request, org.apach
e.tomcat.core.Response)
void org.apache.tomcat.service.http.HttpConnectionHandler.processConnection(org.apache.tomca
t.service.TcpConnection, java.lang.Object[])
void org.apache.tomcat.service.TcpConnectionThread.run()
void java.lang.Thread.run()
Which means that there is a difference relative to the VM version.
All the names are correct on 8i deployment. And all necessary files are on classpath, (including the EJB source and generated jars, that are also in the /lib on the context dochome).
Any thoughts?
Thanks,
Eduardo
null

Wrap text options, are they really limited?

I was curious if there was a way to dial in precise NONuniform wrapping options.
I have a place holder box that I want the text to wrap around and give a 5pt space on all but the right side... I want that 20pts.
In the wrap text options it's all uniform.

You’ll have to edit the path to add 15 points to the right side. One simple way would be to copy it with a +15 point horizontal offset then merge the two paths with Pathfinder.

Why I change the energy level of port in PoE switch, the power usage of port no anyt change

I am enable the EnergyWise on a 3560, plug a IP Phone to a port, the result of the power usage read by SNMP is 6kw, when i change the energy level from 10 to 0 by SNMP, the LCD on IP Phone is goes to dark and phone cannot be use, but when I get the power usage of port by SNMP again, the result still is 6kw. Can anyone tell me why?

This project is just a short animation so every time I import the stills they are of the wrong duration so I try changing the duration by the other methods described previously, fail to be able to do that, erase everything from the project, restart and start again, initially with the preferences. So there's nothing for the still frames to conflict with. It's not the fact that there is a batch of stills that is the problem either as I keep experimenting with with single or small groups of stills in that context. I've also tried importing a variety of still formats into other projects. This is fairly new software. Could this be an incurable fault?
1.25GHz Power PC G4 1MB L3 cache Mac OS X (10.4.9) 80GHz hard drive 1.5 GHz Ram plus Firewire 400 250 GHz la Cie external hard dri

Remote span between Extreme and Cisco switches

Hello,
I need to configure remote span between Extreme Networks X460-24p and Cisco Cataylst 2960X switches. 2 IP phones are connected to ports 15 and 17 on Extreme switch, and should be monitored to port 1/0/47 on Cisco switch. Extreme and Cisco switches are interconnected with trunk (port 28 on Extreme with port 1/0/51 on Cisco).
I configured the following:
On Extreme switch:
configure mirror mode enhanced
enable mirroring to port 28 remote-tag 1000
configure mirroring add port 17 ingress-and-egress
configure mirroring add port 15 ingress-and-egress
On Cisco switch:
vlan 1000
name RemoteSPAN
remote-span
monitor session 1 destination interface Gi1/0/47
monitor session 1 source remote vlan 1000
But this is not working :(
Does enyone have experience with this? I really need help to make this work.
Thanks.

OK, this configuration is actually working :)

Which CISCO switch supports SFP, SFP+ and 10G ethernet ports

I would like to have information about a CISCO switch which can support fiber ports SFP(1g) and SFP+(10g) and copper 1g and 10g ethernet ports. And will it also software upgradable to support L3 protocols ?

You can choose from the Cisco 3560-E, 4900, 4500, and 6500 series switches. That's in order of capability (and cost!), from least to greatest.
The 3560-E and 4900 series are fixed chassis systems (the 4900M is semi-modular) while the 4500 and 6500 series are completely modular - buy the chassis and populate it according to your requirements.
In addition to the references cited above, also refer to the Cisco Products Quick Reference Guide (CPQRG), available at http://www.cisco.com/en/US/prod/qrg/index.html
Hope this helps. Please rate this post if it does.

How to get info over snmp on cisco switch whether native vlan on a port is tagged or not?

Hi!
I want to know which oid(s) should I query to know whether native vlan on trunk port on cisco switch is tagged or not?
I am querying the oid .1.3.6.1.4.1.9.9.46.1.6.3.0 (vlanTrunkPortsDot1qTag) on cisco 3560 (E Series) and I am getting global value. Also, this OID is showing as deprecated. So I query .1.3.6.1.4.1.9.9.246.1.6 (cltcDot1qAllTagged) and its subtree, but no value is returned.
Switch Version is
Cisco IOS Software, C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(50)SE2

Keep in mind that DHCP is a broadcast packet to start. So the AP can only listen in the subnet that it has an IP address for.
Now, for any other subnet you can use the AP for DHCP but you have to have an IP helper address on your L3 pointing back to the AP.
That being said, I wouldn't use the DHCP server on the AP as it is limited. You'd be better off using a Microsoft server or some other device that is designed for DHCP.
HTH,
Steve

Child DC cannot Replicate to Parent DC, because of connection errors. MS PortQryUI shows that ports 3268 and 3269 are not listening,

I started a support case with Microsoft to help me with raising the our domain Forest level because i received a message stating that there were Windows 2000 PDC still listed in the database. These PDCs were removed years ago. The tech saw all of the problems
i was having with domain replication so that is where he started. running the MS PortQryUI shows that ports 3268 and 3269 are not listening, (TCP port 3268 (unknown service): NOT LISTENING) when run FROM a Child domain controller against the Parent
Domain controller. Between the 2 Child domain controllers these ports are listening.
The Windows firewall is not running on any of the controllers, i removed a virus protect client from all of the servers, although i didn't enable the firewall there either, but these ports are still not listening on the Parent DC.
I need help debugging this. I am not very familiar with network sniffers so if i need to run one i'll need some guidance. This DC only has one NIC, all IP addresses are static, all servers are setup like this. All servers are in the same subnet, on the same
lan, on the same cisco switch, there shouldn't be anything blocking this port from starting.
I looked over other post that show this same problem, but they don't give a solution. If i am not using the Windows firewall why wouldn't these ports be open?
Any ideas? web searches are all over the map on trying to find the reason for this.
Bobby

Try running the below command on the DCs that you think have the ports blocked or all the DCs.
netdiag /test:ipsec /debug > c:\dcname-ipseclog.log
Open that from the C drive and see if there is anything saying block or filters.
Also, just for kicks have you disabled the firewall service on the DCs?
And just for kicks have you tried enabling firewalls ports on all the DCs? The KB is below
http://support.microsoft.com/kb/555381/en-us
Step 1 - netdiag results
Step 2 - disable the firewall service on all DCs if step 1 was negative
Step 3 - enable the firewalls on all DCs per KB 555381 if step 2 doesn't work
Let us know how it goes!
If it answered your question, remember to “Mark as Answer”.
If you found this post helpful, please “Vote as Helpful”.
Postings are provided “AS IS” with no warranties, and confers no rights.
Active Directory: Ultimate Reading Collection

Bridge Groups, are they required?

Hi All
I'm currently a tad confused about Bridge Groups and ASA/FWSM in transparent more. Are they really required or not?
Here one sample: http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/interface_complete_transparent.html
It's written:
At least one bridge group is required per context or in single mode.
So that really sounds like yes you need one.
Where as this config sample here: http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008089f467.shtml or many others I found online, never have a bridge group configured.
Could somebody please enlighten me about what is correct?
And does it matter if it's an active/standby configuration?
Thanks a lot
pato

Pato,
It depends. On the newer ASA and FWSM you need the BVI. It is just to configure the management IP. This is required.
The old link (the second one that you listed) has the management IP (not under the int BVI) but on the newer ASA code you can see it is configured under the int BVI as you can see here:
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/interface_complete_transparent.html#wp1382356
-Kureli

Management port in Cisco Switches (are they really physical port)

Similar Messages

Maybe you are looking for