Manipulate destination numnber for incoming calls in CCM

dial-out digit translation can be done with translational patterns in CCM config.
Similarly how do we translate INCOMING digit strings ?
For example, suppose we want to change all incoming calls destined to 234XXX to 567XXX.

Use translation patterns.
For example if the inbound DID number is 234111 and you would like it to ring extension 567222:
Configure a translation pattern of
234111.
(notice the dot at the end!)
then configure discard digits to predot which drops the entire string of 234111
then configure prefix digits of 567222
So basically 234111 matches the translation pattern and discards all digits but appends 567222 causing the call to ring 567222.
Same thing can be done for ranges. For example:
234.XXX would match incoming DID range 234000-234999 and I could prefix it with a 567 causing the translations to ring 567000-567999 (drop the 234 and prefix the 567).
Please rate all posts!

Similar Messages

  • Callerid for incoming call

    I have configured some clients number as CCM users so that we can easily find and call them from the Corporate Directory. Is it possible for these clients names to show up in the phone for incoming calls (from PSTN)?Some kind of lookup in LDAP...
    I use CCM 4.2
    Darek

    The callerinfo service from the SDK should help you get started. Unfortunately, adding users in ccm only populates the directory - the info shown on the display when making calls is taken from the lines, and I have no clue how ccm would react if you created dummy phones with dummy lines that have the proper number.. the name would probably still not be displayed since the call doesn't come from the line in question but a PSTN trunk.

  • My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.

    My iphone 4S has problem in making and receiving the calls. While making the call , call fails and netwrok disappears. Like wise no voice is heard for incoming calls. This happened after return from the overseas travel.

    Hello SamSax
    Check out the assist page below for troubleshooting call connectivity.
    Calls and connection issues
    http://www.apple.com/support/iphone/assistant/calls/
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • Bluetooth no longer works for incoming calls after recent update

    When I updated my Bluetooth to iOS 6, the Bluetooth no longer works for incoming calls. I press button to answer call, it makes a small cracking noise, and then sends the call to my phone. I can use the Bluetooth for outgoing calls and it works just fine. I was hoping when I updated to iOS 6.0.1 that the problem would be fixed. I have uninstalled and reinstalled Bluetooth but that has not helped either. I am frustrated. I have a LG HBM-905 Bluetooth that I loved prior to this problem.

    Magically started working today after I synced.
    Post relates to: Treo 700w (Verizon)

  • TS2634 My iPhone 4s does not ring for incoming calls. Ring tone is set/settings/sound. It used to ring. I think it has to do with updating to IOS 7.0.4? After updating IOS 7.0.3 my microphone stopped working. Had to clear/reload.

    My iPhone 4s does not ring for incoming calls. Ring tone set and used to ring. I think it has something to do with updating the IOS 7.0.4. When I updated to 7.0.3 the microphone stopped working. Had to call Apple Support and cleared phone and reloaded. ($57 charge). Any suggestions?

    Start with your finger at the bottom of the screen (about even with the home button) and swipe in an upward motion.  There should be a row of icons at the top of a grey field.  if the quarter-moon icon is bright white, tap it.  If it was (and still is) dark, take the iPhone in to be evaluated by a qualified technician.

  • My new iPhone 5S will not ring for incoming calls.  It vibrates. I've tried suggested tips for iPhone 4 but it doesn't work for 5S.  Please help!!

    Can anyone help.  My new iPhone 5S does not ring for incoming calls.  It vibrates.  How can I get ringer to work?

    Hello lyngos,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iPhone: No sound or distorted sound from speaker
    http://support.apple.com/kb/TS2802
    If an audio issue occurs when using a specific application, try testing other applications to see if the issue persists.
    If the iPhone is paired with a Bluetooth headset or car kit:
    Try turning off Bluetooth.
    If you experience difficulties with the Bluetooth feature, follow these troubleshooting steps.
    Restart the iPhone.
    If restarting doesn't fix the issue, ensure that your iPhone is updated to the latest version of iOS.
    Best of luck,
    Mario

  • My phone displays numbers instead of contact names for incoming calls and text - how do I fix?

    My phone displays numbers instead of contact names for incoming calls and text - how do I fix?  It used to display the names if there was a contact listed, now it just shows numbers regardless of whether or not the number corresponds to a contact name in the contact list.  Can anyone help?  I googled this problem and lots of folks have experienced it, however there is not a consensus for a resolution.

    Alexandribill, I have been having the exact same issue.  I got a new phone and restored my contacts.  If the # doesn't have the area code first then the name isn't shown.  I just added my husbands area code to my phone and called my phone from his and now his name shows up...Ugh, I have to go through and manually add the area code to all my contacts....
    I'd say Verizon needs to rewrite their program to include the area code in the restoring from backup process!

  • 2960X 15.02(EX5) %AAA-3-ACCT_LOW_MEM_UID_FAIL:AAA unable to create UID for incoming calls due to insufficient processor memory.

    Deployed four 2960X switches in a stack.  All okay for about one month then tried to web browse for the first time via firefox which partially displayed the page.  I assumed this was a browser error.  So tried Chrome then IE which both failed.  Chrome was a bad display and IE fails to connect.
    After this, I could not telnet or ssh.  Plugged into the console and immediately started receiving:
    %AAA-3-ACCT_LOW_MEM_UID_FAIL: AAA unable to create UID for incoming calls due to insufficient processor memory
    %% Low on memory; try again later
    I am unable to log in.  I have a TAC case logged but the first step to try is a reboot which will be difficult until I can get a maintenance window.  When I do get a maintenance window, I would also like to deploy a fix such as a different version of code or a work-around cofig command.  I don't mind disabling HTTP.
    Any suggestions?

    I am currently working with TAC
    The switches failed about 18 hours later and had to be rebooted to get back up.  Now that I have console/telnet access, I can see the memory being depleted mostly by the Auth Manager process at about the same rate as free memory is dropping.
    SW13#sho proc mem sort | i Auth Manager
     191   0  177721332   95004616   34757416          0          0 Auth Manager
    SW13#sho proc mem sort | i Auth Manager
     191   0  177754888   95025696   34759780          0          0 Auth Manager
    SW13#sho proc mem sort | i Auth Manager
     191   0  177774316   95037928   34761056          0          0 Auth Manager
    SW13#sho proc mem sort | i Auth Manager
     191   0  177799720   95053940   34762888          0          0 Auth Manager
    SW13#sho proc mem sort | i Auth Manager
     191   0  177824976   95069732   34764696          0          0 Auth Manager
    SW13#
    SW13#
    SW13#sho proc mem sort | i Processor
    Processor Pool Total:  442796836 Used:  103448576 Free:  339348260
    SW13#sho proc mem sort | i Processor
    Processor Pool Total:  442796836 Used:  103454416 Free:  339342420
    SW13#sho proc mem sort | i Processor
    Processor Pool Total:  442796836 Used:  103455860 Free:  339340976
    SW13#sho proc mem sort | i Processor
    Processor Pool Total:  442796836 Used:  103459236 Free:  339337600
    SW13#sho proc mem sort | i Processor
    Processor Pool Total:  442796836 Used:  103461040 Free:  339335796

  • Please help ... have new samsung ativ se windows 8 phone ... screen lock is on to require password, but on incoming calls its not locked ... how do i lock it for incoming calls too ???? thanks

    please help ... have new samsung ativ se windows 8 phone ... screen lock is on to require password, but on incoming calls its not locked ... how do i lock it for incoming calls too ???? thanks

    Personal rant, why do people write the entire problem in topic line
    It's not possible with Windows Phone 8.  What's the point, a call is coming in and the phone allows you to answer.

  • How can I get volume on my I6 to hear incoming calls . I went to setting , sounds, and selected a tone, but still no sound for incoming calls, texts, or other notifications.

    How can I get volume on my I6 to hear incoming calls . I went to setting , sounds, and selected a tone, but still no sound for incoming calls, texts, or other notifications.

    Hi rsample,
    Thank you for visiting Apple Support Communities.
    Your symptoms make it sound like the iPhone side switch is set to silent mode.
    iOS: Understanding sounds, ringtones, and alerts
    Set your device to silent mode
    iPhone: Toggle the Ring/Silent switch on the side of the device.
    Best Regards,
    Nubz

  • After update to OS4.2.1 I can not get the ringer to work for incoming calls

    after update to OS4.2.1 I can not get the ringer to work for incoming calls. If I set Vibrate on, that's the only notification I get. Tried everything including blowing away ALL my apps and restoring phone to new. Lost all my apps but the ringer still won't ring

    God Bless u! LOL I have an otterbox case on my phone and had no clue that the mute button was there....Thank you so much!! The volume on my movies & everything else worked...even when I would go into "settings" and adjust the volume of the ringtone. I knew it was something simple...Thanks again..

  • Ringer doesn't work for incoming calls

    My iPhone 4 ringer won't work for incoming calls. It is not on vibrate only and the ringer works through the earphones when earphones are connected. Any suggestions?

    Thank you so very much.
    . Simple yet perplexing.. I bought the waterproof case and had them put it on before leaving the store.. GRANTED, I never read the instructions.. Just knew it must have been something in the way I programmed the phone. I especially loved that you put up an illustration with your explanation. 
    Mahalo,
    Donna Jo

  • Bring back full screen pictures for incoming calls

    Bring back full screen pictures for incoming calls in the new update !!!!

    Feedback to Apple does not go here, it goes here: www.apple.com/feedback and click on the appropriate link.
    This is a user to user forum.

  • N81 Photo for Incoming Call

    Hey Guys,
    Got a new n81, is there anyway I can get a full screen photo to come up for incoming calls, rather than the stupid little, tiny and undefinable thumbnail?

    24-Dec-2007 12:34 PM
    steals41 wrote:
    Hey Guys,
    Got a new n81, is there anyway I can get a full screen photo to come up for incoming calls, rather than the stupid little, tiny and undefinable thumbnail?
    there are 3rd party applications that can do this, check skyecaller, best full screen caller for s60 3rd, and still others... the downside, you have to pay...

  • Can Cisco Historical Reports Report Average Hold Time for Incoming Calls?

    Is the a way that Cisco Historical can report on the Average Hold Time for Incoming Calls? User is trying to figure out if there is a hold time prior to the agent picking up the call.
    I am running CRS Historical Reports Versions 5.0 (2.5).

    Hi,
    You can check the link belowCisco Unified Contact Center Express 5.0 Historical Reporting Administrator and Developer Guide:
    http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_5_0/programming/hr_admin_devp/crs501hd.pdf
    this document includes all the details regarding the reports and its cutomization.
    Regards,
    Trad

Maybe you are looking for

  • ANYBODY WANT TO SEE THE INSIDE OF THE ZEN MICRO?

    If u want to see a step by step guide thats takes u through the process of taking apart the Zen Micro...then go to Check the Zen Micro out FROM the Inside Its pretty cool...it shows every little detail...Message Edited by noappendix90 on 06-06-2005 0

  • Some javascript code does not work out in a .jspx page

    To the experienced: I am trying to improve some pages in my application. In one of the pages, there are only two elements in the form: an input box (for user to put in his username) and a submit button. What I am trying to do are: 1. Make the input b

  • I can't remember my iphone password and it's closed me out.  How do I reset?

    i can't remember my iphone password and it's closed me out.  How do I reset?

  • Theme icon images in GridView

    Not sure if this is something that I've read about already somewhere, but I've been spinning my wheels a bit trying to come up with a better solution. In most of my GridViews, I have already modified them a fair amount (added extra data by looping th

  • Trying to download Designer from Oracle Corp

    I have (in Vain) been trying to download designer release 6 with frustration. I left it overnight three times and come back in morning only to find it has hung on "two seconds"!!!. I need to get hold of designer and this is a great hinderance - is it