Manufacturing programming mode is set to unlocked

Hi All, Have just received a new laptop from HP that came, for some obscure reason we're yet to fathom without the operating system on the disk.
I've spoken to HP and they're sending out a recovery disk. In the meantime I've installed Windows 8 using my own media. But. When the laptop boots I keep getting this message; "manufacturing programming mode is set to unlocked" Anyone know what this is, what the effect is on the laptop? I've tried updating the BIOS but it still comes up. Also, the 'born on' date within the BIOS is showing as 0/0/0 . Thanks

Hello, I just got the response from the engineering guys. During their way in the factory, the units are set in MPM (Manufacturing Programming Mode) for all the funtionnal tests. This MPM is then deactivated at the end of the production line.For a small bunch of units (included yours), the MPM deactivation failed. The main issue is that, even if your Win8 key has been embedded in your BIOS, the MPM mode avoids WIndows to access and recognize it. A simple tool has been developped to solve this issue, but is confidential and can only be used by HP repair partners.You may ask why, so I'l explain quickly : this tool is harmless for almost every user, but it can be used by evil-minded persons to create BIOS viruses or hacking stuff. So, I'm sorry to inform you that the only way to get your BIOS in standard mode, and get your Win8 key recognized properly is to send your unit in repair. Regards.

Similar Messages

Manufacture programming mode is in unlock mode

Hi all,
I am using Hp envy m6 1104 tx , windows 8 OS. Recently i had a problem with my laptop so they changed the motherboard .After that, my problem had been solved but i am receiving the message "manufacture programming mode is in unlock mode" . Eventhough there is no disturbance because of it , it is little annoying. So please someone help me to get rid of it.

RaviShankar1994 wrote:
Hi all,
I am using Hp envy m6 1104 tx , windows 8 OS. Recently i had a problem with my laptop so they changed the motherboard .After that, my problem had been solved but i am receiving the message "manufacture programming mode is in unlock mode" . Eventhough there is no disturbance because of it , it is little annoying. So please someone help me to get rid of it.
Hi
The only fix available for this is to send the laptop back to HP again it seems: Contact HP
The message means that the laptop hasn't finished being setup by HP and only they can fix it
I believe this post summarizes the issue best.
eBuzz_Lightyear posted has posted an explanation on why it needs to be sent in and why it cannot be done outside of an HP service center.
thanks,
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

Submit Program "Compile value set hierarchies" manually

We am trying to submit the program "Compile value set hierarchies" manullay through the API , apps.fnd_flex_val_api.submit_vset_hierarchy_compiler, without any success.
Through the API, the program is submitted however it goes into "Pending" and "Stand By" mode, worse thing is we cannot view this through the front end (EBS).
Program "Compile value set hierarchies" has a method type of Immediate we cannot sub,it this through the EBS Form manually.
Is there anything I am missing with the above.
Also, any suggestions to submit the progarm ""Compile value set hierarchies" manually will be greatly appreciated.
Thanks,
Jay

Also, any suggestions to submit the progarm ""Compile value set hierarchies" manually will be greatly appreciated.You can use CONCSUB to submit the concurrent program from the OS -- How To Submit A Concurrent Request Using CONCSUB Syntax [ID 457519.1
Thanks,
Hussein

Re: Primay IDE channel Transfer mode is set to PIO mode - Enabling DMA Stat

Hi
I have installed Xp Professional Recently on my desktop ...
My Primay IDE channel Transfer mode is set to PIO mode...even if i try to change to DME if available its not changing....
I tried a option to run a VB script to change the DMA status but no luck..
Can anyone help me know if any option is available to change the DMA status
Regards
sunny.

Hello suneel
Sorry to interrupt this discussion but I feel it goes somehow in wrong direction.
If I understand you right you just want to install WXP on your Satellite A300. Am I right about that?
On this forum you can find, I believe, hundreds of threads with precise description how to do this.
What you need is WXP installations CD with integrated SATA driver.
Check please this page . There you can find nice description how to find SATA drivers. At the end you can also find link to guide for "Slipstreaming SATA driver into WinXp boot cd using nLite".
When the WXP is installed just continue with WXp driver installation. If your notebook is WXP supported you can find them on Toshiba download page.
Hope this helps.
Good luck!

Is there api function to change access mode and set a passcode to recording in meeting?

Is there api function to change access mode and set a passcode to recording in meeting?
When I'm trying to use "action=acl-field-update&acl-id=SCO_ID_RECORDING&field-id=meeting-passcode&value=MY_PASSC ODE" it just clean the password and do not set it or change.
And "action=permissions-update&acl-id=SCO_ID_RECORDING&principal-id=public-access&permission- id=view-hidden" do not work too.

There is not a specific API for doing this. This was discussed in the other Connect forum here, Adobe Connect User Community.
For you call I would make the second part differently. Instead of 'field-id=meeting-passcode&value=MY_PASSCODE' I would call 'meeting-passcode=MY_PASSCODE' and see if that worked better.

Error : Offline Mode is SET to "True"

I have clustered enviroment . I ran the Package by executing Dtsx File and it got the error "product level is insufficient..." then i found that i need to install remaing SSIS Component. After Instaling those Component . while i was running the package again it is giving the Error "Package Failed becasue Offline Mode is set to True. When i Check in Design it was False. So Why Suddenly it is Throwing that Error.
Plsease Help me on That

   Hi,
      There is another option to set the work offline mode with out opening the project itself. I think in your case it is better to set this property prior to open the project, why because after changing in the solution still you find some errors related to work offline. So I think it is better to follow the steps in the given link to set work offline mode without opening the project.
     http://agilebi.com/cs/blogs/jwelch/archive/2009/05/12/setting-work-offline-without-opening-the-project.aspx
Lakshman

Packing list - Driver Program and Layout set name for Smartform

Hi ,
Anybody knows about print program and Layout set name for PACKING LIST in Smartform.
Regards,
Kumar S

Hi Bhuvaneswari,
For Creating Adobe Interactive form, you need the below configuration:
Server side:
Server running on ABAP/Java stack configured with ADS
For ADS Configuration, follow the below link:
https://service.sap.com/~form/handler?_APP=01100107900000000342&_EVENT=REDIR&_NNUM=0000894009&nlang=E
Client Side:
The required Reader version depends on your usage situation.
For SAP Interactive Forms by Adobe, we generally recommend the following:
Adobe Acrobat Version 7.0. 9 or higher
Adobe Reader Version 7.0.9 or higher
If you require forms for one of the scenarios listed below, you must use Reader 8.1.
These are:
Forms in Web Dynpro applications that are integrated at runtime using xACF (Active Components Framework) ZCI (Zero Client Installation).
Forms in scenarios that use digital signatures.
If you use interactive forms in Web Dynpro for Java and these interactive forms are included using ZCI (Zero Client Installation) at runtime, you must read Note 1055911. Note 1055911 specifies the required reader version and contains further detailed information.
Reward points if found helpful.
Regards,
Arafat

Query read / cache modes are set in BW

Hi Experts,
What is query read / cache modes are set in BW in order to improve the query performance?
Thanks
Rohan

Hi
The read mode determines how the OLAP processor gets data during navigation. You can set the mode in Customizing for an InfoProvider and in the Query Monitor for a query.
http://help.sap.com/saphelp_nw04/helpdata/en/57/b10022e849774f9961aa179e8763b6/content.htm
Assign points if it helps...
Regards,
ARK

What is the block diagram of the feedback loop when op mode is set to velocity?

On 7344s, is the feedback loop changed when the operation mode is set to velocity? Is it still a “position feedback” loop with just a ramp at the input? Or is there an additionnal derivitive to find the speed and the input command is a speed?

When making a move where the encoder is not configured for velocity feedback, the control loop uses actual position vs. expected position as a function of time to correct for the velocity output. However, when the encoder is configured for velocity feedback, we actually use the velocity based on encoder feedback in the control loop and this also allows us to use the functionality of the Kv term to smooth velocity response.
Best Regards,
Chris D
NI Applications Engineer

Manufacturing programs in SAP 3.1H

Hi...
I tried to find manufacturing program (MP) in SAP 3.1H but cannot find. Is MP is supported in this SAP version? Currently, we are running MP outside SAP.
TQ
henery

Hi,
You can use the IDoc types ORDERS01/ORDERS02 of message type ORDERS to create POs in SAP R/3 3.1H.
regards,
Imran

Droid X2 in some kind of program mode? HELP!!!!

My son came home with his Droid X2 in some kind of wierd program mode. Will not boot, just keeps restarting over and over withthis display:
Bootloader
30.04
Battery OK
Ok to Program
Connect USB
Data Cable
connect the cable and it changes to
Bootloader
30.04
Battery OK
Ok to Program
Transfer Mode
USB
and thats it, never ever get past it, no matter what! HELP!! This is his phone for emergencies only, and he has jsut started to drive by himself.

Try removing the battery. With the battery removed, press and hold the Power button for 5 secs. Reinsert battery and power it up .... if that doesn't work, the phone may be "bricked" (corrupted) and time to take to a Verizon store and have the technicians re-flash it ... If he has pics/video/music/data on the external card that he wants to save, remove the card BEFORE any attempts to reset the phone by the Verizon store.
edit: PS - are you sure the battery didn't get drained? Plug it into the wall outlet using the supplied charger - make sure it is charged all the way and not out of juice.
and here is a link to the Factory reset procedure if you wish to try it without going to the Verizon store
http://support.verizonwireless.com/clc/devices/knowledge_base.html?id=33552#alt

Can a CX600 in basic mode be set to have a longer status/presence change setting to Away that 5 minutes?

Update -- I realize this was asked and answered back in 2011 here:
http://social.technet.microsoft.com/Forums/en-US/22c41af2-2829-4be0-9a09-3389f764123a/is-it-possible-to-set-cx600-presence-status-from-deskphone-dnd-busy-avail-etc?forum=ocsclients So now my basic question is, has anything changed?
The symptom: After 5 minutes, this stand lone Polycom CX600 phone running in basic mode sets itself to away. While presence is 'away', it can receive calls directly to its extension, however it does not receive calls from the reponse group it's
a member of. While it's set to 'available' presense, it receives calls from the response group successfully. A Lync resource account with an external phone number/full enterprise voice, is used to sign into this phone. It's Lync 2013.
I've tried within the phone menu in basic mode, to reset the presnse to 'available', but it will still revert to 'away' after five minutes. I've done a hard reset, externally provisioned with USB cable, and from the computer Lync client, set my 'away'
time to the max allowed 360 minutes. However, this did not carry over to the hard phone. I realize I might be able to jury-rig the calendar to always show as available, but I beleive this would only remain if the phone kept operating in enhanced
mode (which is not an option at this site).
So my question is: can a CX600 in basic mode be set to have a longer status/presence change setting to Away that 5 minutes? Again, I realize the answer from that 2011 thread above is 'no', thought I'd ask again in case anything's changed in 2 years.

I didn’t notice there is option on Lync CX600 to control this setting.
The setting from Lync desktop isn’t related with the setting on phone.
That setting is controlled by the local registry key.
For Response Group, you can select Attendant routing method.
Attendant offers a new call to all agents who are signed into Lync Server and the Response Group application at the same time, regardless of their current presence.
Lisa Zheng
TechNet Community Support

Fndload command to download concurrent program without value set definition

Hi All,
Please let me know if you know fndload command to download concurrent program without value set definition.
Thanks,
Viaswas
Edited by: 873477 on Mar 8, 2012 1:55 AM

I agree with Sandeep -- The only option is editing the ldt file after the download and before you upload it.
Thanks,
Hussein

I am trying to open a video in a website and it says, "This video is unavailable in safe mode" What setting do I need to change and how do I do that? Thanks

Apple OSX version 10.9.5
Processor 2.7 GHz Intel Core i5
I am trying to open a video in a website and it says, "This video is unavailable in safe mode" What setting do I need to change and how do I do that? Thanks

https://support.google.com/youtube/answer/174084?hl=en

WRE54G does not recongize WRT100 when WRT100 network mode is set to Mixed

The only time that WRE54 makes a connection to the WRT100 is when the Wireless Network Mode (under Wirless Settings) is set to BG-MIXED and the Standard Channel is identified.
If you selete MIXED for the Network mode all other setting within the WRT100 are set to auto and the WRG54 does not make a connection to the WRT100. So if you have a mixed enivorment with N B and G. The WRE54 will be useless.
Currently the expander does make a connection to the WRT100 when the Network Mode is set to BG-Mixed and the Standard Channel is identified.
Any Updates that will correct this commmunication problem would be benificial. So the one could have a truely mixed environment.

Hi Scrooge,
I have both pieces of hardware to the newest firmware. I tried your settings, however the WRE54G did not connect to WRT100. To reduce the amount of typing I didn't include Wireless --> Advance Wireless Settings within my note, I ensure you though I did exactly as you suggested.
On the WRT100
Wireless --> Basic Wirless Settings
Network Mode is Mixed
Network Name (SSID): HAM
Radio Band: Auto - 20/40Mhz Channel
Wide Channel: Auto
Standard Channel: Auto
SSID Broadcast: Enabled
Security --> Firewall (the only things I have mark are):
SPI Firewall Protection
Filter INDENT (PORT 113)
Please note that the filter Anonymous Internet Requests is not checked.
The WRE54G connects to WRT100 with these settings:
Wireless ---> Basic Wireless Settings
Network Mode: BG-MIXED
Network Name (SSID): Ham
Radio Band: IS NULLED OUT
WIDE Channel: IS NULLED OUT
Stardard Channel: 10 - 2.457GHz
SSID Broadcast: Enabled
suggestions?

Manufacturing programming mode is set to unlocked

Similar Messages

Maybe you are looking for