Mapping error in BDOCS
Hi Experts
Daily we have BDOCS with Bdoc state description "Mapping error" and following errormessage "Processing of document with Guid DEE4C70ABC20D1F18A4900101825B820 is canceled" and " Validation error occurred: Module CRM_DOWNLOAD_BTMBDOC_VAL, BDoc type BUS_TRANS_MSG.
When we reproces the Bdoc it works and the error dissapears.
The errormessage is not very informative so we don't know what the original error is and we would like to avoid the reprocessing of the BDOCS.
Do you know the rootcause and how to avoid these errors?
best regards
Jørgen Jensen
Please check the following OSS note and implement the corrections that are suggested.
SAP Note 629016 - Automatic restart of BUS_TRANS_MSG
Similar Messages
-
Bdoc state E08 , Mapping Error , BUS_TRANS_MSG
SAP CRM
trx:- SMW01
Bdoc Error
Bdoc State --> E08
Bdoc state Descriptin --> Mapping Error
Bdoc Type --> BUS_TRANS_MSG
How to resolve this errorHello Aup,
What is the BDoc Type you are talking about?
Click on Error/Receiver tab and check for the exact error message.
If you give me the details,I can help you solving this Mapping Error.
Thanks and Best Regards,
Shanthala Kudva. -
How to clear Mapping Error Bdocs
Hi,
We are getting Mapping error bdcos in SMW01 if there is an error while data is downloading from ECC to CRM. We are fixing the issue by looking at the BDOC error description. We are unable to re-process these error bdocs after fixing the issue as it is not allowing. To fix the issue we are re-processing the corresponding queue in SMQ2 and queues are processing successfully. the problem is these error bdocs are sitting in data base and we want to clear them.
Can any one please let me know how we can re-process these kind of mapping error bdocs?
Thanks,
RajinikanthHi ,
Below logic may be useful.
SELECT bdoc_id
bdoc_type
bdoc_state
snd_date
snd_time
qname
INTO TABLE lt_inque
FROM smw3_bdoc
WHERE bdoc_type IN s_bdoc
AND qname IN s_qname
AND bdoc_state IN r_err.(r_err = E01,E02.....E09)
LOOP AT lt_inque INTO ls_inque.
DATA:lv_bdoc_id TYPE smog_tid.
CLEAR lv_bdoc_id.
lv_bdoc_id = ls_inque-bdoc_id.
CALL METHOD cl_smw_flow=>restart_processing
EXPORTING
bdoc_id = lv_bdoc_id
EXCEPTIONS
bdoc_not_found = 1
bdoc_locked = 2
bdoc_was_processed = 3
internal_error = 4
OTHERS = 5.
ENDLOOP.
Thank you,
Gangadhar.S -
Hi All
I am facing a problem is Business partner download from ECC to CRM.
The Initial Load on CUSTOMER_MAIN is successful and the 2 BPs got replicated to CRM.
But, the Initial Load on CUSTOMER_REL has failed (R3AI_CUSTOMER_REL Queue in SYSFAIL state). The BDoc shows a Mapping Error.
Error Details : Technical error occurred (7)
Forward to this, when I create a new BP in ECC, Delta is triggered, but the BP is not created in CRM and the BDoc has the same Mapping Error as above.
Pl help.
Thanks in advance
Regards
SushanthPls slect the BDOC in SMW01 and select the button wHich says 'Show errors and receivers'. You will get popup and slect the radio button of errors. You will see the error. Pls validate and correct them.Then you can reprocess the BDOC.
-
Tcode SMW01 in SAP CRM
Bdoc Error
Bdoc State: E08
Bdoc Description: Mapping error
Bdoc Type: BUS_TRANS_MSG
Bdoc Detail Error Description: Business transaction type ZZZZ does not exist
The ZZZZ is a quotation transaction type maintained in ECC. But we donu2019t want this replicated in CRM, reason why ZZZZ is not maintained in CRM. The queues in SMQ2 is building-up with these error (R3AD_SALESD* with SYSFAIL status), is there a way to block, filter etc. this transaction type to exclude it from replication? Or other better way to address the problem?
Thanks in advance!Hi Noel
try setting a filter on object SALESDOCUMENT in Transaction R3AC1.
Table=VBAK
Field = AUART( its a guess, can't check it in a system)
OP = NE> Not Euqal
Low = ZZZZ
save it. your filters wil also be updated to R/3
Hope it helps
best regards,
Remko -
Mapping error in PI 7.1
Hi All,
When i am trying to create a new mapping or coyping the existing mapping(which is already activated) , i am not able to activate the mapping . I am getting the following error :
Source text of object Message Mapping: new |
urn:abc:MessageOut has syntax errors: Source code has syntax error:
Source strcuture and everything is perfect as i had created previous mapping using the same source structure.
Please advice as to what might be the issue here and what is the solution.
Regards
Vinay P.In each and every mapping which is already avialble in IR and the new ones that i am trying to create ...i am getting the followin exception throughout if press F7 in the mapping ...as a result u cant actiavte any changes in the existing mapping nor in the new mapping
Error:
Source text of object Message Mapping:
Mapping name| urn:abc:namespace:SI_Interface has syntax errors: Source code has syntax error:
Regards
Vinay P. -
Strange Data Mapping Errors after SEM 6 Upgrade. Please assist.
Hi All, I encountered these sudden Mapping errors after I tried to do Testing in Post Upgrade Sand Box. Here I am trying to to perform Collected Reported Financial Data under Data Collection Method for a particular Company Code 3040. Kindly help me with some quick responses as this is kind of high priority. The errors and the Diagnosis Notes I am unable to follow as I do not where I shall write those Mapping Rules they are referring to. I do not even know if that need to apply any SAP Notes as such. Once again Highly appreciate your quick response and Many Thanks in Advance.
Regards, BIP
Input conversion for field Period Value LC has invalid format Message no. UCT8210 Diagnosis The mapping rule for target field Period Value LC contains a move with a selected Input Conversion indicator. Therefore, the system performs an input conversion prior to creating the target data. However, an error in the input conversion occurred while moving the source key figure to the target key figure Period Value LC. This means that the format used for the input conversion is incompatible with the target data. System Response The system will not perform the move. Procedure Examine the mapping rule for field Period Value LC. Either select the Conversion Exit indicator or deselect the Input Conversion indicator. Execute the method again. -
3040 is incompatible with input format for field /1FB/COMPANY Message no. UCT8258 Diagnosis During execution, the method derives the source selection for source field /1FB/COMPANY from the mapping rule for the target field. 3040 is one of the values that were derived for the source selection. The system requires that this value is in the correct SAP-internal format because the Conversion Exit indicator has been selected in the move operator for field /1FB/COMPANY. However, the value 3040 is incompatible with the SAP-internal format. System Response The system attempts to interpret value 3040 as an external format and convert it to the internal format. If this fails, the system is unable to restrict the source selection using source field /1FB/COMPANY. In this case, the system may read more source data than was originally intended, which can affect performance. Procedure In the log, choose the Source button to display the source selections that are used to read the source data. When this appears, examine values selected for field /1FB/COMPANY. If the correct values were selected, you can ignore this message. To prevent this message from being issued, you can select the indicator in the mapping rule used by source field /1FB/COMPANY. If incorrect values were selected, make sure that the mapping rule used by source field /1FB/COMPANY has been defined correctly. If the mapping rule is correct and value (3040) derived for the source selection does not affect the overall result, you can ignore this message. If the source selection does not contain the value 3040 for field /1FB/COMPANY and, because of this, source data that is supposed to be read is not being read, make sure that the mapping rule has been defined correctly. If the source selection does not contain any value for field /1FB/COMPANY, make an estimation as to how much excess source data is being read and whether this might affect system performance. If you do not expect any performance problems, you can ignore this message. In any event, you have the following alternatives if the mapping rule is defined correctly, but the source selection on field /1FB/COMPANY is unsatisfactory: You can define a source selection for field /1FB/COMPANY in the Customizing settings for the method on the Selection tab page. Then the method uses this source selection instead of the source selection derived from inverse interpretation of the mapping rule. You can implement the Business Add-In (BAdI) UC_DATATRANSFER and use the method INVERT to determine the source selection on field /1FB/COMPANY. Then the method uses the result of the INVERT method for the source selection instead of the source selection derived from inverse interpretation of the mapping rule. -
Cannot derive the source selection from target field Version Message no. UCT8252 Diagnosis Field Version has one of the following roles: Consolidation unit Group currency key Fiscal year Posting period Version To delimit the volume of the source data to be read, the system usually derives the source selection from the target selection of such a field. However, the system cannot derive a source selection from field Version. System Response It is possible that a greater volume of source data is being read than is necessary. This can lead to performance issues. Procedure Check whether a mapping rule is defined for field Version. If a mapping rule is defined, you can disregard this warning message. However, if you discover after method execution that the system did not process a large amount of data, and that system performance was not satisfactory, you may want to examine the source selection by choosing the Source button in the log. If the reason for the disregarded data is that too much source data was read because of the unrestricted selection on the source field (which is linked with target field Versionthrough mapping), choose one of the alternatives below: Change the mapping rule for field Version so that the system can derive a delimiting source selection. Implement the Business Add-In (BAdI) UC_DATATRANSFER with the method INVERT to delimit the selection for the source field that is linked via mapping to the target field Version. -
Cannot derive the source selection from target field Group Currency Message no. UCT8252 Diagnosis Field Group Currency has one of the following roles: Consolidation unit Group currency key Fiscal year Posting period Version To delimit the volume of the source data to be read, the system usually derives the source selection from the target selection of such a field. However, the system cannot derive a source selection from field Group Currency. System Response It is possible that a greater volume of source data is being read than is necessary. This can lead to performance issues. Procedure Check whether a mapping rule is defined for field Group Currency. If a mapping rule is defined, you can disregard this warning message. However, if you discover after method execution that the system did not process a large amount of data, and that system performance was not satisfactory, you may want to examine the source selection by choosing the Source button in the log. If the reason for the disregarded data is that too much source data was read because of the unrestricted selection on the source field (which is linked with target field Group Currency through mapping), choose one of the alternatives below: Change the mapping rule for field Group Currency so that the system can derive a delimiting source selection. Implement the Business Add-In (BAdI) UC_DATATRANSFER with the method INVERT to delimit the selection for the source field that is linked via mapping to the target field Group Currency
1 is incompatible with input format for field FISCPERIOD Message no. UCT8258 Diagnosis During execution, the method derives the source selection for source field FISCPERIOD from the mapping rule for the target field. 1 is one of the values that were derived for the source selection. The system requires that this value is in the correct SAP-internal format because the Conversion Exit indicator has been selected in the move operator for field FISCPERIOD. However, the value 1 is incompatible with the SAP-internal format. System Response The system attempts to interpret value 1 as an external format and convert it to the internal format. If this fails, the system is unable to restrict the source selection using source field FISCPERIOD. In this case, the system may read more source data than was originally intended, which can affect performance. Procedure In the log, choose the Source button to display the source selections that are used to read the source data. When this appears, examine values selected for field FISCPERIOD. If the correct values were selected, you can ignore this message. To prevent this message from being issued, you can select the indicator in the mapping rule used by source field FISCPERIOD. If incorrect values were selected, make sure that the mapping rule used by source field FISCPERIOD has been defined correctly. If the mapping rule is correct and value (1) derived for the source selection does not affect the overall result, you can ignore this message. If the source selection does not contain the value 1 for field FISCPERIOD and, because of this, source data that is supposed to be read is not being read, make sure that the mapping rule has been defined correctly. If the source selection does not contain any value for field FISCPERIOD, make an estimation as to how much excess source data is being read and whether this might affect system performance. If you do not expect any performance problems, you can ignore this message. In any event, you have the following alternatives if the mapping rule is defined correctly, but the source selection on field FISCPERIOD is unsatisfactory: You can define a source selection for field FISCPERIOD in the Customizing settings for the method on the Selection tab page. Then the method uses this source selection instead of the source selection derived from inverse interpretation of the mapping rule. You can implement the Business Add-In (BAdI) UC_DATATRANSFER and use the method INVERT to determine the source selection on field FISCPERIOD. Then the method uses the result of the INVERT method for the source selection instead of the source selection derived from inverse interpretation of the mapping rule
Input must be in the format ___,___,__~ Message no. 00088 Diagnosis Your entry does not match the specified input format. System Response The entry in this field was rejected. Procedure The entry must comply with the edit format. The following edit format characters have a special meaning: "_" (underscore) There should be an input character at this point; this should be a number for numeric fields. "." (decimal point) (applies to numeric fields) The decimal point occurs here (setting in the user master record). "," (thousands separator) (applies to numeric fields) This separator occurs (optionally) for more than three figures. Depending on the setting in the user master record, it can be a period or a comma. "V" (applies to numeric fields) The operational sign appears here. If used, it must by at the right margin of the field. The sign is either "-" or " "(space). "~" (tilde) (applies to numeric fields) As of and including this character, leading zeros must also be entered. Otherwise, this character has the same meaning as an underscore. Leading zeros need not be entered on the left of the tilde. They are not output at this position. All other characters have their normal meanings and must be entered in the same position as in the edit format.Hi Dan,
Could you Kiindly advise me where we need to write the Mapping Rules in Consolidation Monitor? All he time the errors refering to Mapping Rules. The only Tab I seen "Mapping" is in Data Basis But as per my Understanding Iwe do not have much to do there as it is system generated Mapping Tab.
Where we actually go and select/deselct those Input Conversion Indicator/ Conversion exit Indicator.
Highly appreciate your advise.
Thanks and Regards,
BIP -
Java.util.EmptyStackException Mapping error
Hi All,
I am integrating SAP ECC 6.0 system with SAP SNC.
For these i am using standard content of SAP SNC
I am getting following mapping error :
TransformerConfigurationException occurred when loading XSLT InvoiceRequest_InvoicInvoic01_01.xsl; details: Could not load stylesheet.com.sap.engine.lib.xml.util.NestedException: Error parsing query. -> java.util.EmptyStackException
Plz help me out
Regards Milanhi,
check the interaface mapping which is used in your flow
inside integration repository - is it working over there?
do you see the XSL file in the external archives in repository?
Regards,
Michal Krawczyk
http://mypigenie.com XI/PI FAQ -
Multi-Mapping Error after copying into new namespace
Hi everybody,
we got a BPM running using a multi-mapping.
We decided to design new namespaces. After copying every IR object (datatype, message-type, mappings etc.) --> SXMB_MONI shows a mapping-error.
But when I take the payload and test the mapping, everything is fine?
Any ideas?
Regards MarioHi,
If your payload has Messages tab remove that..and test the payload.
Payload doesn't have any Messages tab.
Just i have given example payload..this payload two strucures it will split into twofiles..and compare your payload should be like same
<?xml version="1.0" encoding="UTF-8"?>
<STRUCTURE>
<EMP_DETAILS>
<EMPNO>123<EMPNO>
<EMPNAME>XYZ<EMPNAME>
<EMP_DETAILS>
<STUDENT_DET>
<STUO>123<STUNO>
<STUNAME>XYZ<STUNAME>
</STUDENT_DET>
<STRUCTURE>
Regards,
Venu. -
Catch Mapping Error in File to IDoc scenario
Configured BPM and now learning Error Handling. I know that through BPM we can handle system Errors, but I doubt whether Mapping error is a system error.
I am interested to know the classification of errors with examples, preferably listing out all types of errors.
Please provide some weblogs or explain briefly how to handle system and application errors through BPM.
Thanks,
RajaHi Raja,
You will need CCMS if you want to send the Alerts to external system or you want to access the ALerts from the transaction. You can capture your alerts without this also.
When you go to Alert Configuration in the Runtime Workbench you can see Create Alert Rules. These rules are pertaining to the error generated in your AF,AE or IE.
Once you have completed the whole config. The error happening in the AE, IE or AF would trigger the alert. you can see this in your Alert Inbox.
The best would be if you go through the URL I have mentioned below.
http://help.sap.com/saphelp_nw04/helpdata/en/80/942f3ffed33d67e10000000a114084/content.htm
You have to use BPM only if you want to do an activity after the alerts are raised.
Regards
Vijaya
Message was edited by: vijaya kumari -
Mapping Error in XI Configuration for MM-SUS Scenario
Dear Experts,
I am working on MM-SUS Classic Scenario,
We have done all basic setting in SRM, ECC and SUS.
Now we are configuring XI Scenario(Working on ESOA Architecture), while configuring XI Scenario, I follow the mention steps :
I have started from Integration Builder in XI (using T-code SXMB_IFR)
1. I have assigned two Business System( for ECC and SUS) In integration Builder (Creates Communication Channels Automatically) .
2. Modify IDOC and XI Communication in ERP and SUS Business system respectively.
3. Now select Tools -> Transer Integration Scenario from Inegration Repository and Create Scenario in it properly
(Included Assign Services, Configure Connections, Generate etc).
4. In last, save scenario.
After configuration XI I am not getting Scenario Data (Objects and Configuration Overview data) in it.
When i click to Check Configurability under Model Configurator of mine Scenario, I found following Errors ( I am Mentioning only some errors) :
Component View SE_Services_Procurement: Connection from Send Z_CREMAS_SUSMM to Business Partner empfangen has no mapping
Component View SE_Services_Procurement: Connection from Send_PO_From_MM to Receive_Purchase_Order has no mapping
Component View SE_Services_Procurement: Connection from ServiceAcknowledgementConfirmationRequest to ServiceAcknowledgementConfirmationCreate has no mapping
Component View SE_Services_Procurement: Connection from InvoiceRequest senden to Receive INVOIC has no mapping
Kindly correct me if am missing some, and help me out, what should have been done to remove this mapping errors.
Thanks in advance,
Regards,
Pawan KeshwaniIf you are on >= SP9 you do not need to perform that action at all.
Go to SU01 transaction assign SAP_XI_DEVELOPER role for the desired users and try it.
regards
Shravan -
Mapping Error in AAE in PI 7.1
Dear Team,
If we use message mapping along with AAE concept , What are the objects we need to create in ESR and ID .
How can we monitor the messages - messages failed with Mapping Error.Is there any new option available in RWB?
Thanks&Regards
DrumiHi,
ESR Objects are same but in ID we need to create Integrated configuration
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/700058f0-b1a1-2a10-39a8-ab2627b87cfa
If we are using AAE then we don't get any status in SXMB_MONI.
Regards,
Venkata Ramesh -
Mapping error in PI 7.4 dual stack
Dear Experts,
Recently we upgraded our system from PI 7.1 to PI 7.4 dual stack.
Scenerio is ECC->PI->SOAP(Webservice) synchronous
Issue in detail:
We are creating a invoice in ECC system through PI its updating in third party site using SOAP webservice and will get a reference number from that site and then updating in ECC as in synchronous way.
Invoice data's are reached PI sucessfully from ECC but it not updating in the site and getting below mapping error after upgarded to PI 7.4.
Your points will be highly appreciable.
Kindly help to sort out this issue.
Best Regards,
MonikandanHi Monikandan,
It seems you are trying the sign the payload in your java mapping. So, looking at the attached error, there could be 2 possibilities:
1) Either there is no certificate with alias: *_PRD
2) This certificate is stored in some "System" type keystore view which is not accessible from you mapping code. Try to move your certificate to some "User" keystore view.
Thanks & regards,
Piyush -
RFC Lookup mapping error in PI 7.1
Hi Experts,
I´m getting mapping error when executing interface SOAP -> WS (SAP ECC) . The message mapping call RFC Lookup to SAP ECC.
When test the message mapping in Integration Builder the interface calls communication channel by RFC Lookup and works fine.
That interface was imported from QAS environment and was working fine, but in PRD it doesn´t works.
I checked the Interface Determination and the parameter is filled correctly with communication channel. The same communication channel was used on message mapping test.
The Interface Determination in SXI_CACHE has no value assigned to parameter in PRD environment, otherwise, the same interface determination in SXI_CACHE in QAS environment there is value (CC ID).
The problem persists after Cache Refresh in SXI_CACHE and CPA Cache.
Can anyone help me ?
Thanks in advance,
Regis Ferrato
Bellow the trace of error ocurred:Hi Regis,
Please check my reply in your other thread:
Re: RFC Lookup error cache in PI 7.1
Regards,
---Satish -
Hi Gurus,
I am getting mapping error at runtime. Im getiing this error message'com.sap.engine.lib.xml.parser.ParserException: XMLParser : #0 not allowed in Character data sections(:main:, row:1, col:301)'. When i testing in the design level its executed successfully. That is i have copied the entire xml message and paste it in the test tap of the integration directory. when i execute it , it run successfully. Pl help out to resolve this problem.
Regards,
Ramalakshmi.GHi,
This s the audit log ..
2008-07-28 16:29:15 Success
The message was successfully retrieved from the receive queue.
2008-07-28 16:29:15 Success
The message status set to DLNG.
2008-07-28 16:29:15 Success
Delivering to channel: CC_WARRANTY_receiver
2008-07-28 16:29:15 Success
MP: Entering module processor
2008-07-28 16:29:15 Success
MP: Processing local module localejbs/CallSapAdapter
2008-07-28 16:29:15 Success
Receiver JDBC adapter: processing started; QoS required: ExactlyOnce
2008-07-28 16:29:21 Error
JDBC message processing failed; reason Channel has reached maximum concurrency (5,000 concurrent messages) and no free resource found within 5,000 milliseconds; increase the maximum concurrency level
2008-07-28 16:29:21 Error
MP: Exception caught with cause com.sap.aii.af.ra.ms.api.RecoverableException: Channel has reached maximum concurrency (5,000 concurrent messages) and no free resource found within 5,000 milliseconds; increase the maximum concurrency level
2008-07-28 16:29:21 Error
Exception caught by adapter framework: Channel has reached maximum concurrency (5,000 concurrent messages) and no free resource found within 5,000 milliseconds; increase the maximum concurrency level
2008-07-28 16:29:21 Error
Delivery of the message to the application using connection JDBC_http://sap.com/xi/XI/System failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: Channel has reached maximum concurrency (5,000 concurrent messages) and no free resource found within 5,000 milliseconds; increase the maximum concurrency level.
Last four lines descripes the error
Regards,
Ramalakshmi.G
Maybe you are looking for
-
IChat wont connect during webcam
When i try and connect to the webcam with another buddy. It always says communication error. how can i ichat??
-
Running reports in a different app server
Hi, If I use rwbuilder to build a JSP, can I simply drop the JSP into another app server (i.e. Weblogic, or JBoss) and execute it? Or, is 9iAS required? Thanks, Duke [email protected]
-
i was updating my iphone ios suddenly battery was drain and itunes logo appears, how can i recover my file back? does anyone can help me...
-
Error coming - NOT ENOUGH MEMORY while opening MUS...
Hi i have bought nokia 7210 supernova , error is coming NOT ENOUGH MEMORY while opening MUSIC PLAYER can any1 help me in ths plz
-
TS3992 Is it possible to backup documents and photos from my imac to iCloud?
I thought it was possible to backup data to the icloud services previously but I can't see how to do this. Is it really only designed for backup of iOS devices and not from a mac? Thanks