Mass-Storage Fails

I'm Using Nokia Asha 503 Duel Sim.... Everytime I want to Connect It Doesn't response, Then Restarting this Device Fix this problem.. But Unplug the Cable and I'm Retrying to Connect it fails again..
Solved!
Go to Solution.

First connect the cable to the phone and to PC later.
Hope this helps.
-------------------If this post helped you, click on accept as solution.------------------
-----------------------------Appreciate by clicking on white star.----------------------------

Similar Messages

[Solved] Banshee crashes while scanning USB Mass Storage mounted SGS2

I start banshee and then connect my Samsung Galaxy S2 as mass storage. It shows up in Banshee and Banshee starts to scan the folders for files, but at some point it suddenly crashes.
Any idea what is causing the problem here?
Systemd log and Banshee log is below.
EDIT: As it seems, this was a general error of the FS of the SD card. I had to format it, which is unfortunate, but it works again.
journalctl
Oct 15 14:35:03 thomas-laptop kernel: usb 2-1.3: >can't set config #1, error -110
Oct 15 14:35:03 thomas-laptop systemd-udevd[6129]: inotify_add_watch(7, /dev/sdf, 10) failed: No such file or directory
Oct 15 14:35:03 thomas-laptop systemd-udevd[6130]: inotify_add_watch(7, /dev/sde, 10) failed: No such file or directory
Oct 15 14:35:03 thomas-laptop udisksd[994]: Cleaning up mount point /run/media/thomas/0148-1EE4 (device 8:80 no longer exist)
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sdf): FAT read failed (blocknr 5959)
Oct 15 14:35:03 thomas-laptop kernel: Buffer I/O error on device sdf, logical block 48668673
Oct 15 14:35:03 thomas-laptop kernel: lost page write due to I/O error on sdf
Oct 15 14:35:03 thomas-laptop kernel: Buffer I/O error on device sdf, logical block 48668674
Oct 15 14:35:03 thomas-laptop kernel: lost page write due to I/O error on sdf
Oct 15 14:35:03 thomas-laptop kernel: Buffer I/O error on device sdf, logical block 48668675
Oct 15 14:35:03 thomas-laptop kernel: lost page write due to I/O error on sdf
Oct 15 14:35:03 thomas-laptop mtp-probe[6147]: checking bus 2, device 14: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb2/2-1/2-1.3"
Oct 15 14:35:03 thomas-laptop mtp-probe[6147]: bus: 2, device: 14 was not an MTP device
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5924) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5925) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5926) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5927) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5928) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5929) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5930) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5931) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5932) failed
Oct 15 14:35:03 thomas-laptop kernel: FAT-fs (sde): Directory bread(block 5933) failed
Banshee log
[Warn 14:35:03.278] Caught an exception - GLib.GException: Datei oder Verzeichnis nicht gefunden (in `gio-sharp')
at GLib.FileAdapter.EnumerateChildren (System.String attributes, FileQueryInfoFlags flags, GLib.Cancellable cancellable) [0x00000] in <filename unknown>:0
at Banshee.IO.Gio.Directory+<GetFiles>c__Iterator6.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource+<>c__Iterator0.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource.SyncPlaylists () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapSource.Flush () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapSource.Dispose () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapService.UnmapDevice (System.String uuid) [0x00000] in <filename unknown>:0
[Warn 14:35:03.279] Caught an exception - GLib.GException: Keine Berechtigung (in `gio-sharp')
at GLib.FileAdapter.EnumerateChildren (System.String attributes, FileQueryInfoFlags flags, GLib.Cancellable cancellable) [0x00000] in <filename unknown>:0
at Banshee.IO.Gio.Directory+<GetFiles>c__Iterator6.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource+<>c__Iterator0.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource.SyncPlaylists () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapSource.Flush () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapSource.Dispose () [0x00000] in <filename unknown>:0
at Banshee.Dap.DapService.UnmapDevice (System.String uuid) [0x00000] in <filename unknown>:0
Unhandled Exception: GLib.GException: Datei oder Verzeichnis nicht gefunden
at GLib.FileAdapter.EnumerateChildren (System.String attributes, FileQueryInfoFlags flags, GLib.Cancellable cancellable) [0x00000] in <filename unknown>:0
at Banshee.IO.Gio.Directory+<GetFiles>c__Iterator6.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource+<>c__Iterator0.MoveNext () [0x00000] in <filename unknown>:0
at Banshee.Dap.MassStorage.MassStorageSource.OnImportFinished (System.Object o, System.EventArgs args) [0x00000] in <filename unknown>:0
at Hyena.Collections.QueuePipeline`1[System.String].OnFinished () [0x00000] in <filename unknown>:0
at Banshee.Collection.ImportManager.OnFinished () [0x00000] in <filename unknown>:0
at Banshee.Collection.Database.DatabaseImportManager.OnFinished () [0x00000] in <filename unknown>:0
at Hyena.Collections.QueuePipeline`1[System.String].OnElementFinished (System.Object o, System.EventArgs args) [0x00000] in <filename unknown>:0
at Hyena.Collections.QueuePipelineElement`1[System.String].OnFinished () [0x00000] in <filename unknown>:0
at Hyena.Collections.QueuePipelineElement`1[System.String].Processor (System.Object state) [0x00000] in <filename unknown>:0
Last edited by slosd (2012-10-15 14:50:03)

Hello, i too have random freeze without any "usable" info.
The blame "may" (well i think it is) be a "baytay + i915 kernel drivers" fault, these thread are intresting :
- https://bugs.freedesktop.org/show_bug.cgi?id=88012
- https://github.com/OpenELEC/OpenELEC.tv/issues/3726
what intresting is that there is path (for use of "legacy-turbo"), sory not remenber where i get it
-- gpu-drm-i915-fix-vlv-crash.txt --
Revert back to legacy turbo for vlv, fixes random crashes.
Reported by Timothée Giet <[email protected]> on dev@ ml.
https://bugs.freedesktop.org/show_bug.cgi?id=88012#c33
--- linux/drivers/gpu/drm/i915/i915_irq.c.orig
+++ linux/drivers/gpu/drm/i915/i915_irq.c
@@ -4361,12 +4361,7 @@ void intel_irq_init(struct drm_i915_priv
INIT_WORK(&dev_priv->rps.work, gen6_pm_rps_work);
INIT_WORK(&dev_priv->l3_parity.error_work, ivybridge_parity_work);
- /* Let's track the enabled rps events */
- if (IS_VALLEYVIEW(dev_priv) && !IS_CHERRYVIEW(dev_priv))
- /* WaGsvRC0ResidencyMethod:vlv */
- dev_priv->pm_rps_events = GEN6_PM_RP_UP_EI_EXPIRED;
- else
- dev_priv->pm_rps_events = GEN6_PM_RPS_EVENTS;
+ dev_priv->pm_rps_events = GEN6_PM_RPS_EVENTS;
setup_timer(&dev_priv->gpu_error.hangcheck_timer,
i915_hangcheck_elapsed,
I did use the trik on a custom kernel, i do have freeze (none tomoroy but two today but only on using firefox, so may be another probleme (sna)) but not on video (well i had run 15 video same time, and two where running 2 hours after without crash). May be you should try it (i think it work better).
note : link to make custom kernel -> https://wiki.archlinux.org/index.php/Ke … raditional

Device Manager displayed " Mass Storage Controller (Code 28)"

Greetings to all Members
I am using AMD 64 x2 3800+ processor. MSI mortherboard K8N Diamond. Graphic cards, two units, Geforce GTX6600GT. I am running on Window XP SP2. I have also updated the AMD latest drivers.
I noticed each time I log on the computer, the computer would prompt "New Mass Storage Hardware Found" and prompt the wizard to install new found hardware.
I went to device manager and noticed the device status display "This drivers for this device are not installed (Code 28). I have also carry out all the steps as suggested from the device manager menu. Mass Storage Controller location is: PCI Slot 9 (PCI 3, device 0, function 0 is displayed at the Mass Storage Controller Display. The device Instance ID display "PCI\VEN_1095&DEV_3132&SUBSYS_710A1462&REV_01\4&14AECDBO&0&0060.
Try update driver option but to no success. Have all the driver systems (in the CD) that came together with the system installed as well. Again to no success in resoluting the problem.
To my horror after installing the drivers that I have downloaded from MSI website for the said board.
I notice the Virtual drive program failed to initialize.and the following messages were displayed during the installation of the website drivers for the said mortherboard:
There was a problem installing this hardware
Mass Storage Controller
An error occured during the installation of the device. The name is already in use as either a service or a service display name.
Can someone please help me to resolve this problem? Any suggestion or advise would be sincerelt appreciated.
Best Regards
Harry
Can someone please assist and provide me with some guidelines to resolve this problem.

Hi Bas
I manage to remove the yellow exclamation mark from the hardware, device manager by setting the Integrated Peripherals on Board Sil3132 mode from Sata to Raid.
The Sata and Raid controllers is displayed and upon opening it up further, I noticed the following controllers are displayed:
1 ) FarStone CDAWDM2001 SCSI Host Adapter.
2) Silicon Image SIL3132 SataRaid Controller.
Do you think I have set the right thing? Your kind opinion on this. I am using BIOS version used is 1.A
Thanks
Best Regards
Harry

USB Mass Storage Device won't Eject/Unmount

My brother bought a Sanyo ICR-B180NX digital voice recorder last year to use with his iBook. It was working very well up until about August of 2005. At that point, the recorder would mount on the desktop, and he could get all the files off (it records direct to MP3 format rather than WMV, so he can edit his files very easily), but when it came time to eject it, the device icon would disappear and then immediately re-appear on the desktop. The display on the voice recorder remained static at the "Connect" screen.
I believe this happened in conjunction with some sort of OS update, as it was a "sudden" thing. We can't quite recall what happened between the times it worked and the time it stopped working.
I have tried the device on a PC, and it works the way it should, so I don't believe there's anything wrong with it.
Now, I know the system requirements on the website say that you must have Windows, but a statement from a support company (we returned it to the place where we got it, and they sent it out for repairs, and it came back with a letter) states that the device does act as a generic Mass Storage device, and thus may work with most systems.
All my other USB storage devices (ie. SanDisk 12-in-1 card reader, SanDisk Cruzer Titanium 2GB, iPod Photo), and FireWire devices (ie. WiebeTech TrayDock Extreme) work fine and unmount fine.
Does anyone know of any changes to the way Mass Storage devices are ejected in the current iteration of the OS? I haven't had a chance to test the device under an older OS, but will soon.
Alternately, if anyone has any suggestions regarding replacements (not really looking forward to that, given this recorder cost almost $300CAD), let me know. We need a device that can plug in via USB and transfer files to his iBook which he can edit together (he's a newspaper reporter in training, and needs to edit the interviews to take out such things like dead air, etc).
Thanks!
Mike Ma.

Hi
+USB mass storage device. An error occurred during the installation of the device the data is invalid+
This typical error message appears if the installation of external USB devices failed.
Why? This is not easy to say
What you could do firstly is to clean your registry using the freeware software called CCleaner (Google for that).
Install it and clean your OS and the registry entries.
After cleaning access the device manager and remove all USB root hubs and all USB Host controllers from the device list and reboot the notebook.
New reboot should cause a new installation of USB drivers.
Finally try to connect and try to install your external USB devices again.

Help! mass storage error! please help

i was getting frequent crashes in FCP with a Xserve RAID hooked up via fiber channel card for media storage. i'd get the spinning beach ball and would have to do a manual shut down, approx every 20 minutes.
i did a complete erase and install of both system software and final cut pro software. still had problems.
i did the apple hardware test and got the following error code - MASS STORAGE: 2 STF/2/3: SLOT-3, Channel: 1, ID:0, LUN:
i got this error code ONLY when the RAID was hooked up, otherwise everything passed the test. the RAID mounts fine and in the RAID admin tools, everything gets a green light.
since i am under a deadline and don't have a lot of time to troubleshoot, i rented another G5, bought a new fiber channel card with new cables, and hooked it up to the RAID.
i am still getting the same error. again, the RAID array appears on the desktop, and the RAID admin tools finds everything ok - the fiber channel link ups, etc., check out ok.
i really need to sort this out ASAP!! if anyone has any suggestions for me, i'd be most grateful - thank you

Hey Kappy,
I haven't seen that specific error before (prob since I hardly ever do apple hardware tests), but the spinning beach ball and the restarting does sound very familiar.
If you've been getting this on both machines, my first guess is going to be a failing drive, since that can easily cause beachballs and hangs. Usually errors come up in RAID Admin, but I've personally had at least 5 times where a drive spazzes and there's no error at all to warn you (and of course applecare wont replace a drive or do anything about it til it happens, and you're screwed with performance until then) Possible things to do to troubleshoot:
1) Play a video clip in FCP and loop it. Meanwhile, check the raid's blue LED activity lights and see if any of them are out of sync (not blinking in tandem with the rest) If so, chances are that's your problem drive. If the machine starts to spazz, from what i've seen, if its a drive problem, that one drive's LED will stay solid while the others blink seldomely, which means that drive is working overtime to keep up, but can't.
2) Run drive conditioning from RAID Admin (I believe its only available under version 1.5). This will run for a while and is a great way to force the array to reveal any errors or failures in any of the drives. If you have a problem drive, this will be the best way to force it to turn yellow or red.
For time constraints/deadlines, once you find out what the problem drive is and if the blue light is acting very erradically, drive conditioning will usually trigger the yellow or red light immidately (to where you can call apple and get it replaced under applecare). If you cant wait that long, pull the drive while its still green, and the raid will run in a degraded state (but your performance will be about back to normal). Just make sure and realize that you're not protected in Raid 5 anymore at that point. Even though, this has saved me in deadlines when I had a busted drive and couldn't play back a single stream of DV.
As a seperate comment, going out on a limb and speculating (So dont hold me to it), if it was a drive issue, judging by your error, I would guess it's drive 3.
NOTE: Always have a backup

E71 Firmware Bug with USB Mass Storage.

Hi,
Just got a e71, it has the latest firmware, it's mostly good except for this bug.
If you install a new theme on a memory card and then attempt to use the USB for mass storage it will always lock the card no matter how you disconnect from the USB, it always reports Memory card in use.
What is supposed to happen is the phone is supposed to switch to a theme on the phone memory and unload the theme on the card, it does indeed switch themes, but does not unload the theme on the card, so the only way to free the card is to reboot the phone.
If anyone from Nokia is looking at this forum, you guys need to fix these little bugs with the firmware. A update to the OS the E71x is using would be nice by the way. I paid a lot of money for this unlocked phone and expect it to be rock solid.

I had this problem with the memory card. All you do is set the USB connection to PC suit and not Mass Storage. If it's in PC suit mode you don't loose the memory card and it always let you access it. I never bother with mass storage anymore. Also set to don't ask if you want. I ahve no issues since I di this and am using the 200 firmware.
To transfer files to the card I go into my computer, double click the picture of the nokia E71 and then double click the memory card and access it that way. Hope this helps as it's a pain installing everything on the phone.
Just another quick tip if you download the themes through your phone like me once installed and after a re-start something may try and install and fail once your phone starts up. It will do this everytime you re-start your phone. To fix the issue you have to browse the memory card with 'view hidden folders' selected in Windows and delete certain sis files from a certain folder. I can't remember off the top of my head but it explains it in another post in this forum. I can't take the credit for it.
Ben

Mass storage

I am trying to transfer media files to my blackberry, when loading the software it comes with an error msg "music services failed to load, an unexpected error as occurred" any ideas
also how do I get me phone to be in mass storage mode.
Many thanks

At what point (what are you doing) when you get that error message?
1. Go to Options >> Media Card (or Memory on some devices).
(some themes or BlackBerrys may call this "Settings >> Media Card")
2. Check the following settings (if they are not listed this way, then change to reflect the following:
a) Media Card Support: On
b) Mass Storage Mode Support: On
c) Auto Enable Mass Storage: Yes
3. Save the settings and exit
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

"mass storage" error

Suddenly began to have problems with my powerbook 2 days ago. Strange fluctuations in screen brightness with corresponding audible surges from the speakers. I reset the power management unit and the problem seemed to have been solved. Now, the system locked up giving me all kinds of odd errors: for example, while using iWeb I could not publish because the disk was full despite there being plenty of free space on my hard drive and on iDisk; trying to save in pages or iWeb gives an error with a strange number that I failed to note.
My worst fear being the loss of data, I quickly decided to hook up the powerbook in Target Disk mode to my girlfriend's iMac to transfer critical data for safe keeping. However, the iMac won't recognize the disk though in system profile it's listed under the "firewire" tab. I then ran the Apple Hardware Test and got the following error for "mass Storage"
"Error*Code... 2STF/8/3:ATA-100ata-6-MASTER"
Can anyone tell me what the heck is going on here?
One thing to note, believe it or not my dog (got to love her) ate through my DVD collection which included my Tiger install DVD. So, booting from that DVD is not an option. Any ideas, thoughts, hints, spectulations, or intuitions would be much appreciated.

If you ever see an error with the Apple Hardware Test, you will have to take your Mac in for service to repair it. That appears to indicate a physical/hardware problem with your hard drive. It will probably need to be replaced. It could be an issue with your logic board and the ATA bus itself, but that's a little less likely.
If you send the PowerBook in for hard drive service, it may come back with a new hard drive and the same version of Mac OS X installed that came with your PowerBook when you bought it. AppleCare support will send you a new set of install disks, but they may charge you around $60 to replace them. If your PowerBook came with Mac OS X 10.4, you may not be able to use a retail copy of Tiger to re-install.
-Doug

USB MASS STORAGE DRIVER DEVICE CODE 10

AFTER INSTALLING UPDATES, CONFIGURATION STARTS, BUT FAILS AFTER 30%. THIS IS DUE TO A USB MASS STORAGE DEVICE
FAILURE, A CODE 10 ERROR. HOW CAN I CORRECT THIS PROBLEM, I'VE TRIED DOWNLOADING DRIVERS, BUT I AM CURRENTLY
USING THE LATEST VERSION OF THIS DRIVER. HELP!!!

Check the following link and find the part of the text "Common resolutions for Code 10 error".
http://support.microsoft.com/kb/943104/en-us

Hardware Test Error Message - Mass Storage Error code ata 1/6/8 HD: 2,0

I have an imac 15" flat Panel, 700 MHz . after getting the flashing question mark, running or trying to run all the standard tests, (pram, Software Restore, disk repair, reinstall, kernel repairs) I never see the hard drive or volume. I saw it was a maxtor HD with 0 bytes at one point.
I now ran the Apple Hardware Test think I lost the Hard Drive...this is the feed back:
Airport- Passed
Logic Board - Passed
Mass Storage - Error Detected
Memory - Has Not been Run yet
Modem - Device Found
Video RAM - Has not been run yet
Error Code ata 1/6/8 HD: 2,0
Could anyone help me diagnose the issue? I think I can replace the HArd Drive myself, if I knew this was the problem and what I need to buy to replace.
Thanks,

I have a different take to a brody having replaced my hard disk and opened my iMac G4 up several times. Many people find that Apple Authorized Service Providers tend to give extortionate quotes for such repairs. Feel free to get a quote yourself. I'll provide the same advice I've given to many many other Apple Discussions users who have successfully replaced their hard disk themselves.
The iMac uses a standard desktop PC hard drive. It is 3.5" wide and in the iMac G4 uses the IDE connection. The iMac 700MHz 15" has an ATA66 bus so can use ATA66, ATA100 or ATA133 drives but not ATA33 or SATA. You should buy a 7,200rpm drive with a cache of 8Mb or higher as this also increases the speed over the original 5,400rpm drive installed so you should get a performance increase.
Here is a list of suitable hard drives.
It's pretty fiddly to work inside an iMac G4 so you must be very cautious. Always take anti-static precautions. Here are three options for guiding you through the procedure:
MacWorld
xlr8yourmac
Service Manuals
I've also taken a fair few photos which you can find here.
I'd advise reading the reports on the xlr8yourmac's drive database so get other people's experiences first.
You must replace the Thermal Paste when you close the iMac up or it will overheat.
It's probably worth replacing the PRAM Battery whilst you're in there as these have a finite life (once they fail to re-charge you may start to run in to snags - it's only a $5 part).
The hard disk should be set to Master (link).
Some iMac G4 700MHz users have reported that they are unable to address hard drives larger that 128GB, there is an application called SpeedTools that can be used to overcome this addressing limitation.
You might also give consideration to installing a 512MB PC133 DIMM or an 18x DVD±RW Dual Layer burner whilst you do this update; both of which will have to be removed during the process.
You must be very careful around the video connector in the iMac; it really is very fragile. In fact there is no need to touch it at all in my experience.
It is possible that the ATA controller on the iMac's logic board has failed rather than the hard disk. Given the cost of the logic-board it would not be cost-effective for an iMac G4 700MHz.
Let us know how you get on.
mrtotes

How to use cRIO USB mass storage?

Hi,
I am using the NI9215 as an analog input port and want to write the data into an external USB mass storage which is connected in the
cRIo-9012 USB port. I do not have any idea how to write the data into USB mass storage, does anyone can give me some help?

Differences among brands and models are due to the fact that certain devices take greater liberties with the USB mass storage device specification than others. A venerable operating system like Windows (or even Linux) is shot through with workarounds for device- and manufacturer-specific issues that are not present (as much) in VxWorks, which is the OS used on the cRIO-9012. Therefore only devices that adhere very rigorously to the specification are going to work properly.
Unfortunately, degree of adherence to the USB spec is not something that's generally published about a device, nor is there any sort of official certification process. So to some extent it's trial and error. I am working with our support enginners currently to develop a list of devices that NI certifies as interoperable with VxWorks, and also VxWorks is increasing the robustness of their USB support with every release.
EDIT: And the advice about reformatting the device is very sound. The cRIO-9012 does not support the NTFS file system, only FAT 12, 16, and 32. If the USB device is formatted for NTFS, it will not function properly.
Finally, if anyone sees a storage device that fails to work properly despite all these suggestions, please post as much information as possible (model number, manufacturer, capacity). Having this information will allow us to work with the manufacturers of VxWorks to improve USB support.
Message Edited by CharlesC on 02-22-2007 12:12 PM

Mass Storage -Hard Drive -Error 2STF/8/3:ATA-100ata-6-Master

I ran a hardware test and got the following error message on the Mass Storage (hard drive) device, what does it mean? Is the hard drive toast? Is there a way to fix this?
***error**
2STF/8/3:ATA-100ata-6-Master
***error***

That error indicates the hard drive is failing or has failed. It could be that the drive itself is at fault, or that it is not correctly connected, or that the ATA controller on the logic board is faulty. There are also indications that in some instances, that fault code can be generated by a problem with the optical drive which prevents the system correctly addressing the hard drive.
Of those, the only truly serious possibility is the ATA controller, since it would require replacement of the logic board, which is really not an economic repair.
In this situation, and assuming the system in not under warranty (clearly if it is, take it in for service) then I would remove the top, check the drive tray is correctly mounted, and remove the optical drive to see if the hard drive then functions. If not, then swap in another hard drive then try and set the new drive up. If it continues to fail with this error, it would then point to the logic board.

Mass storage controller problem

i have a toshiba satelite m45 and have reinstalled windows xp sp3.i downloaded all the neccesary drivers but still get a popup saying new hardware was found (mass storage controller)i looked in the device manager but there isnt any question marks to the uninstalled hardware.its allways fails when i try to update it,and can never figure out how to fix it.
and before that i had this error "texas instruments pcixx21 integrated flashmedia controller".it was the same and didnt show a question mark in the device manager.i eventually got that to go away buy installing the drivers over again.is this a common problem,and does anyone know how to fix it?thanks

i tried to install the flash media driver and it popped up found hardware for the texas instruments pcixx21 integrated flashmedia controller and mass storage controller.both says were not installed properly.i have a screenshot also.
screenshot

Nokia Asha 503 Mass storage Problem

Mass storage isn't works.... Restarting this phone, it works then.....
So, I have to restart this phone Several times?

Sourav55555 wrote:
Mass storage isn't works.... Restarting this phone, it works then.....
Remove the memory card and use a card reader to check if it works fine. If not, then you might have to reformat the memory card.
If the above fails, you may need to do a full reset on your phone either by performing a factory reset or by using the Nokia Software Recovery Tool.
Good luck

This morning my PB G4 would not get to the password screen after power on. I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage E

this morning my PB G4 would not get to the password screen after power on. I have rebooted many times and very loud noises (like a HD spinning/rubbing) emits. Tried the Install disk and it cannot find the hard drive. Ran HW test and got a "Mass storage Error Code" message.
Did my HD just crash and unrecoverable? Time to replace my notebook?

I believe your hard drive has failed. Hope you have a backup.
Failing Hard Drive Sounds http://datacent.com/hard_drive_sounds.php
Listed by drive manufacturer. Click on the > next to the drive & you will hear the typical failure sound.
How to Tell When Your Hard Drive is Going to Fail
http://www.lifehack.org/articles/technology/how-to-tell-when-your-hard-drive-is- going-to-fail.html
Grinding And Clicking – Symptoms Of A Failing Hard Drive
http://pcperformancetools.com/getdata/grinding-and-clicking-symptoms-of-failing- hard-drive.html
Failing Hard Drives
http://losangelescomputerhelp.com/computer_networking_news/failing-hard-drives.h tml
 Cheers, Tom

Mass-Storage Fails

Similar Messages

Maybe you are looking for