Master Static noise when I boot up

no matter how i shutdown the msipvs or radio tuner before shutting down my pc, i get a static noise when i switch the pc back on.
to temporary solve the problem (at least while i'm using the pc), i run either pvs or radio then exit the apps.
anyone throwing in the permanent fix for this problem will be greatly recognized!!!
tnx

The problem is related to the Crossbar driver
There was a solution posted before in this forum and that was to change the crossbar driver from MSI with one of from a leadtec xp2000
check https://forum-en.msi.com/index.php?threa...crossbar+driver

Similar Messages

Static noises when calling normal?

i have been experiencing static noises when making phone calls. im the only one who can hear them and not the person im calling.(already confirmed myself.) is the at&t service or is the iphone defected. i hear the static through the normal earpiece at the top(not headset) and in speaker mode. thanks.

Hi all,
Mine does it too. Has nothing to do whatsoever with at&t. None of my other phones do this.
I have a hiss sound I can hear in my earpiece that kind of overlays each word I speak.
I have posted 2 other threads here and only Allan Sampson has responded and understood what I was describing.
The information I have gathered online points to the fact that all NON 3 G phones have a poor sound quality compared to a 3G phone of any make.
Or maybe some of us just have bad ear piece speakers. If so chalk this iPhone up as bad returned iPhone #5.

G4 400 wont boot and static noise when powering up

I tried turning on my friend g4 400 mhz sawtooth and it makes 3 loud static noises during the typical powerup noise. then it wont do anything else, the light is on, sounds like its running, but its not giving me anything. I am not sure what that sound is indicating. any help would be appreciated. thankyou

Hi, Dustin!
I'm no expert on this, but my gut says there may be a problem in one of two areas: RAM (the modules or the bus interface itself) or Video (monitor, cabling, or video card).
Try resetting PRAM and NVRAM. Try the NVRAM reset via open firmware as explained in the link.
Although you might not be able to successfully do so, disconnect all peripherals except for the keyboard, mouse, and monitor, and then try booting to and running the Apple Hardware Test Disk (if you have it). Otherwise, remove/swap around the RAM modules and test startup. Reset the video card and test again. If you have another monitor available, swap it and test again...
Gary
1GHz DP G4 Quicksilver 2002, 400MHz B&W rev.2 G3, Mac SE30 Mac OS X (10.4.2) 5G iPod, Epson 2200 & R300 & LW Select 360 Printers, Epson 3200 Scanner

Takes too long to hibernate when I close the lid - Also random device noise when it boots up

Hello guys.
Ever since i've wiped the machine, i've been having these two problems. When I close the lid, it used to go to sleep straight away, but now I can see the sleep light (and the power button) flash and flash, then it goes to sleep.
When waking up it goes through the lenovo startup screen and resuming windows, then it asks for a password, before I used to open the lid and it would ask me for the password straight away. I know it was going to sleep because I could hear the beep straight away when I closed and opened it, but now it just takes too long.
Also, everytime I boot up into windows or resume into windows from a sleep state, I can hear the device noise, like something is being plugged in/out. But there is nothing being plugged in or out at the time. I can't get to device manager quick enough to see what it is that is causing it.
But all drivers seem okay.
Thanks in advance.
Sam.
EDIT: Also noticed, when the lid is closed, randomly the laptop turns off (hear the beep) an then turns back off again.
Weird.
T420 model number: 4180-PR1 with OS: Windows 7 Pro 64 bit
T420 4180-PR1 - OS: Windows 7 Pro 64 bit
Solved!
Go to Solution.

Hi Sam,
is this to do with the T420 model number: 4180-PR1 with OS: Windows 7 64 bit installed on it as in another thread you posted in?
Maybe you could pop the information into your signature; members like to know which system and OS are involved. At the top next to Sign Out choose My Settings > Personal Profile > Personal Information - Signature
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Flicking noise when I boot my iMac from sleep mode??

Another problem that has struck my iMac..
Every time I boot my Mac form sleep mode it comes on and starts clicking/flicking like the fan's cough on somehting. I know it's not the fan and it's most likley to be the HD but worth asking just incase it's a problem that I can fix (which i dought).
I think I'm going to take the Mac into a Apple store and see how much it will cost to fix. Because I can't see myself going back to Microsoft windows again if this brakes.. I would rather just wait and save for a new iMac.
I've had this problem quite a while but never payed much attention to it as I thought it was because of the room tempreture. But it's annoying me now, so if anyone knows what it could be please tell me..
Thnaks
Nick

Been waiting along time for this problem to be fixed. Unfortunately the update hasn't help at all and even made the situation worse. Now my airplay connection from iMac to stereo abruptly stops after about 10-15 min. so I have to go over and quit wifi, start it up and find my airport network. Not sure why it always has a problem with the apple airport network. My neighbor's pc network is always there.

BOSE Mk1 Soundock & 1st Gen iPod Touch + Electric/Static Noise**

I have recently bought a Bose Mk1 Soundock for my 1st Gen iPod Touch, at first worked fine, brilliant lil gadet, but then it started to generate a reeeely high pitched electric/static noise when the battery was fully charged when music was both on or off, i returned and got an exchange for a brand new bose which didnt solve the problem so i can only assume its the ipod, so i put in a service request with apple, off it went and came back 'un-repaired' as apple 'could not reproduce the problem/s'?? since then it has started generating this noise regardles of battery level or music on/off and is reely, reely, reely annoying and is rendering the unit virtually unusable with the bose, am i the only one who can hear this or is anyone else having/had the same problem??!?

Hey
Is it this noise:
http://www.youtube.com/watch?v=yqeggo7DSGg
If so, I'm having the same problem. I've emailed B&W support about it. It doesn't occur without the ipod docked. Doesn't seem to be a problem with other docks though, so it could be fixable with a firmware update. In fact, it wasn't ever a problem with the original Zeppelin firmware, only after the update.

Static noise in Game mode on Windows 7

I encountered a very annoying bug/feature after I installed Windows 7 x64, and the latest driver for X-Fi Titanium: 2.7.0007. There is a good chance that the same thing happens on Vista/32bit, because this is not a problem on Windows XP.
No matter what setting you choose in Game mode, there is always some static noise when using DTS Connect / Dolby Digital Li've. You can best notice this listening to some low frequency sounds when the amplitude changes. It took me a while to figure out that it doesn't happen in the Entertainment mode. Not sure if it happens without DTS/DLL.
It looks to me like bad resampling, because DTS Connect / DDL need to mix all sources into one 48kHz output at some point. I remembered the issues I had with the good old SB Li've! when all sounds had to be software resampled to 48kHz for the best quality since the hardware resampler sucked. I tested it by resampling the souce to 48kHz using a HQ resampler, and, indeed, ?most artifacts have gone. The most artifacts are generated by CMSS-3D (anything above 50% generates noise). But even that didn't fix it completely. The only thing that helped was the Entertainment mode.
I'm not talking about noise you can hear using hi-tech equipment. I bet you could notice it using low-end speakers without a problem. Creative should add this to the documentation, or fix the issue. Remember, Game mode is the default.
Regards.

I read some other threads and I do have 4GB od RAM. I also tested XFI_SupportPack_2_0, and everything works fine there even in Game mode. Plus, DTS Neo PC also works perfectly (it couldn't be enabled with the official drivers).
I don't know if this is funny or sad. :S

Iphone4 microphone makes static noises while I make a call using headphones?

I have iphone 4 32GB. When I make a call using headphones the microphone at bottom-left of the phone makes static noises when it comes into contact with anything.
It is really annoying as I hear loud noises while my phone is on my pocket and I am making a call using headphones.
Could you please help what could be the solution? Is this a fault with the hardware or software?
NB: I have recently installed the latest version 5.01.
Many thanks for your help.
Shaz

I found the answer myself, I actually bought earphones from a corner mobile shop for £10. and they happened to be fake and do ot disable microphone while plugged.
so the point is buy the original earphones from apple website.

Mic is making a static noise

I never had a problem with my mic before, but recently it has started making a static noise when i talk, that i cant hear but others can. I have a pavilion desktop pc. It does it with any mic i plug in, and in any voice chat programme i use. I have tried changing some of the setting etc, but am not great with computers, so im not really sure what i need to look for, any help would be appreciated, thanks

Hi,
Try checking if there isn't anything weird with the sound setting.
Go to "Control Panel", click on "Sound", in the "Playback" tab click on the "Speaker". You can check the settings from there then.
Good luck!
Although I am an HP employee, I am speaking on my behalf of myself and not on behalf of HP.
Best Regards,
AngeH
Disclaimer:
Although I am an HP employee, I am speaking for myself and not for HP.
儘管我是惠普的員工，但是我在此的發言並不代表惠普，只代表我自己。

Static noises in external/internal speakers

Why does my external/internal speakers make a static noise when I plug my AC cord into the computer, but when i unplug the AC adaptor power source, the noise goes away but I am draining my battery?

took computer to apple store...i had a bad logic board

Mouse trails and static noise - video refresh problem?

I get mouse trails that don't refresh away and static noise when I click and drag.
In most apps that allow scrolling, like safari. I will get a small box on the screen that will create a trail of that small square all the way down my screen. It looks like a trail. Also if I click on a window and move it I get a static noise. The noise sounds like little crickets. Any ideas? I am thinking about spending money to upgrade this box and am worried I may be throwing money away.

Great news. Original owner upgraded the graphics card on this machine when he bought a new monitor. He had the original nvidia fx 5200 which I promptly installed, replacing the ATI Radeon 9600. Problem solved. I still hear the noise when I drag the windows around, not sure why but there are no more mouse trails. It was the graphics card!

How can I get my ipod nano (6th gen) to stop making a static-y noise when I try to listen to my music? It has been doing this for a week and the music is faint while the static is louder than it.

It has been doing this for a week and the music is faint while the static is louder than it. I try plugging it in to my iTunes and when I un-plug it, it still makes the loud static noise. I have also tried tapping my knuckle on the back of my ipod nano. This has not damaged it at all nor caused this to my ipod. There is no water damage to the ipod. Only a few scratches from a couple drops. The drops have been on concrete but not at a very high distance. How to I stop this? Do I need to replace my ipod instead?

Have you tried a different pair of earbuds/headphones to rule out a pair of damaged/faulty ones? You might also want to make sure the headphones are securely and firmly seated in Nano's headphone jack. Lastly, check the headphone jack for any signs of debris or damage. You may need to have the headphone jack replaced either by Apple or a third party repair company.
I assume this static is present on any track you listen to versus only particular ones?
B-rock

Consistant Static Noise noise changes when performing actions on laptop, need he

I have a Sound Blaster Li've 24-bit External sound card which I have my DJ equipment connected to. The problem I am coming across is static noise coming through the speakers. The sound is there when the audio board is powered on?or off. I have already did basic troubleshooting and I refered to theKnowledge Base on this site.
Power of laptop is in a different source, soundcard has the latest downloads, speaker cables are fine etc. I want to check the Bios on my computer but I don't think I am that tactful to do this. Anyways, I will cut and paste my message I started on Mediamonkey.com, I am GDTRFB66. I basically wan't to know if there is a filter or a better sound card I can purchase to knock out the interference the computer is making. I Usually only run 2 speakers, sometimes I will connect smaller speakers through my audio board and run it through source. Also the ststic noise is there when I just connect my computer directly to my laptop and it uses the onboard sound card, so I doubt it is an issue with the sound card.
I really would like some additional help here is the post I submitted on Media Monkey......Next Message
<span class="name">]

<span class="nav">http://thalassa.bio.auth.gr
http://93.95.7.84/SRVS/CGI-BIN/WEBCGI.EXE/,/?St=426,E=0000000000226533826,K=772,Sxi=2,Kb=ww_en glish_add,VARSET=ws:http://us.creative.com/,Case=obj(656)<span class="gensmall"><span class="nav">[size="2" color="#006699">Back to top[size="2" color="#006699"><img border="0" src="http://www.mediamonkey.com/forum/templates/subSilver/images/lang_english/icon_profile.gif" alt="View user's profile"><img border="0" src="http://www.mediamonkey.com/forum/templates/subSilver/images/lang_english/icon_pm.gif" alt="Send private message"><SCRIPT language=JavaScript type=text/javascript></SCRIPT>?<img width="" height="" src="http://www.mediamonkey.com/forum/templates/subSilver/images/spacer.gif" alt=""><span class="name">]GDTRFB66
<span class="postdetails">
[size="">Joined: 05 May 2007
Posts: 7
[size=""><img width="2" height="9[/img] src="http://www.mediamonkey.com/forum/templates/subSilver/images/icon_minipost.gif" alt="Post"><span class="postdetails">[size="">Posted: Sun May 20, 2007 2:54 am<span class="gen">?[size="">Post subject: [size=""><img border="0" src="http://www.mediamonkey.com/forum/templates/subSilver/images/lang_english/icon_quote.gif" alt="Reply with quote"><img border="0" src="http://www.mediamonkey.com/forum/templates/subSilver/images/lang_english/icon_edit.gif" alt="Edit/Delete this post"><img border="0" src="http://www.mediamonkey.com/forum/templates/subSilver/images/icon_delete.gif" alt="Delete this post">i am hesitant to screw with my bios I'm not that comfortable in performing those ste
ps.
Or should I give it a shot

When I take video with my HTC 8X the sound covered up with static noise, similar to the old TV white screen noise.

When I take video with my HTC 8X the sound covered up with static noise, similar to the old TV white screen noise.

mellosteve,
This isn't a known issue with the device so I am surprised that you are having these issues. When you first noticed the issue, was anything else done on the device at that time? Any new apps added, etc? Let's try to put the phone into Safe Mode and test. If it works while in Safe Mode, we will know it could be a 3rd party app causing the static. Here are the steps to put the phone into Safe Mode: http://vz.to/1MrjzMg
ErinW_VZW
Follow us on Twitter @VZWSupport
If my response answered your question please click the �Correct Answer� button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

T500 SSD Whirring Noise When Booting Up

I have only had this T500 since July 2009 and last week it started making a whirring noise when I turn it on. Before last week it was so quiet and it booted up very fast. Now it's making this noise and slower. I thought solid state hard drives were supposed to be quiet. Any suggestions?

They have no moving parts. Are you sure it wasn't the cooling fan?

Master Static noise when I boot up

Similar Messages

Maybe you are looking for