Mavericks  / Samsung ML-2250 printing failure,

Hi all!
Since I have installed Mavericks. My Samsung ML-2250 fails to print. The error in the job queue is : Stopped - "filter' failed.
The error msg at this location is :  /var/log/cups/error_log.
D [17/Nov/2013:21:32:40 +0000]
D [17/Nov/2013:21:32:40 +0000] [Job 10] End of messages
D [17/Nov/2013:21:32:40 +0000] [Job 10] printer-state=3(idle)
D [17/Nov/2013:21:32:40 +0000] [Job 10] printer-state-message="Sending data to printer."
D [17/Nov/2013:21:32:40 +0000] [Job 10] printer-state-reasons=none
Please can you help?!
Cheers

You should contact Samsung. That model isn't shown as supported here:
http://support.apple.com/kb/HT3669
If you have the 10.8 drivers installed, you could try resetting the print system and re-adding the printer.

Similar Messages

  • HT3669 Do you have driver for  Samsung ML 1210 printer  for mavericks? Please help!

    Do you have driver for  Samsung ML 1210 printer  for mavericks? Please help!

    I don't believe that Samsung ever made a driver for this model that worked in intel. Unfortunately, I think your printer is just too old. You can read here
    http://technicalfault.net/2011/08/22/installing-the-samsung-ml-1210-printer-on-m ac-os-x-lion/
    or else contact Samsung and ask them.
    Cheers
    Pete

  • Samsung laser suddenly printing garbage

    I've been using a Samsung ML 2250 successfully for a couple of years with my Imac with the Gutenprint drivers. But suddenly, perhaps after my last software update, it began to print garbage on page after page after page. The first page starts out "%1PS-Adobe-3.0"
    Is this related to an update of my OS? I've reset the printer system, reinstalled, but same problem.
    Any suggestions?

    Partial success--this thread helped: (Thanks to Matt Broughton)
    http://discussions.apple.com/message.jspa?messageID=3442464
    I installed the HPJIS driver found at http://www.linuxfoundation.org/en/OpenPrinting/MacOSX/hpijs.
    It doesn't support the ML 2250 but it does support the ML 2150. I installed it as that and it printed a page correctly.
    I'm still not sure what happened to the Gutenprint driver...

  • Photosmart 7510 e all in one series Printer failure Oxc19a0023

    After having been turned off for several months, I plugged in my 7510e and the following message came on the screen.
    Printer failure, Oxc19a0023, Please turn printer off then on. I did this with no change. I unplugged both electric plus and USB and reconnected. I removed the cartridges and replaced but the same message keeps coming and I cannot get passed this message. If anyone has had this problem and has been able to fix this or if anyone know how to fix this I would really appreciate some help. Thank you.

    Hello @TSLI76 , and welcome to the HP Forums, I hope you enjoy your experience!
    I see you are experiencing 0x errors.  I would like to help!
    I would recommend removing the ink cartridges, and performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
    I would also recommend this document on An 'Ink System Failure' or a '0x ...' Error Message Displays on the HP Printer Control Panel.
    Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
    Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
    Jamieson
    I work on behalf of HP
    "Remember, I'm pulling for you, we're all in this together!" - Red Green.

  • Since upgrading to Mavericks, my Canon MP980 printer no longer works. I've tried deleting the printer and adding it again. the process ends with my mac saying the software is not currently available from the software update server.

    Since upgrading to Mavericks, my Canon MP980 printer no longer works. I've tried deleting the printer and adding it again. I've downloaded the driver software from Canon. My Mac dropbox tells me "the selected printer software is available from Apple", but when I click to download it, the process ends with my mac saying the software is not currently available from the software update server.

    Open Finder and click on Go > Go to Folder. Then type
    /Library/Printers/Canon
    and press Enter. This will show the BJPrinter and iJScanner folders. You could try moving or trashing this folder and then installing the driver that you downloaded from Canon again.

  • How do I make my workhorse Samsung ML-1740 printer work with Yosemite 10.10.3?

    How do I make my workhorse Samsung ML-1740 printer work with Yosemite 10.10.3?

    Are any other Samsung printers affected? Or is this a specific ML-1915 problem?
    (I still can print on a shared ML-1640 printer at home.)
    I hope Apple is also reading these forums: As said before: This started with the OS X update!
    Then in between there were Samsung printer updates issued by Apple via the softwareupdated function.
    They also didn´t solve the problem.
    I also tried removing the printer and adding/setting it up again. (as suggested in the Apple support pages).
    Even installing the original driver that came on CD. That didn´t help either.
    Logic still tells me that this is an Apple / OS X caused problem. Please fix it!!!
    I have no intention to buy a new printer just because Apple might have messed up with their updates.
    The printer was working perfectly fine and it just got a fresh toner.

  • Hp officejet 6700 premium printer-printer failure

    I bought a HP officejet 6700 premium a month ago.  I installed the printer and it printed ok.  But after a few day of use, it suddenly stopped printing and gave a Printer Failure massage on the front control panel.  The message says: There is a problem with the printer or ink system.  Turn printer off then on.  If problem persists, contact HP.  I have checked all ink cartridges.  They seem all ok (I have only print less than 10 pages since installed). I have turned power off and on several times but did'nt work.   I have searched all over the HP website for help, but still can't find a solution for my printer problem.   I deeply appreciate, if someone can help me or give me directions to make my new printer works again.  Thanks.
    P.S.  my laptop computer has Winders 7.
    ns42

    Did you get an answer? I think the problem lies with the blue print head with the gold pins, they get bent when you change out printer cartridges. Several folks have had this problem. I watched a youtube video of repairman saying both the 6600 and 6700 printer had this problem until HP changed the print heads. I am still fussing with HP about this but I am pretty certain I won't get any relief. Good luck

  • Error Message: "Printer Failure" Problem with print or ink system . . .

    Greetings!
    I wasn't exactly sure where to post this, but the error message refers to printer or ink system failure so I thought this was a good place. I've been troubleshooting my parents HP OfficeJet Pro 8600 AiO for the last 2 or 3 hours with little success. I've contacted HP tech support but they wanted $200 for the work to be done and neither I nor my parents, who are retired and on a fixed income, have the money to spare.
    The tech support people said it was probably a problem with the drivers, so I attempted to reinstall the software, but that didn't help at all. A brief description of the problem might shed some light on this awful situation. Since this morning, my father tried to print something and the printer itself gave the following error message on the front LCD panel on the device itself (ie, not on Windows, but on the printer's display):
        "Printer Failure
         There is a problem with the printer or ink system. Turn it off, then on. If the problem persists, contact HP."
    Obviously my first course of action was to follow the directions. I turned it off, unplugged the cord, waited approx. 30 seconds, replugged it in and turned it back on. Nothing changed. I've also tried removing and replacing the Ink cartridges, checking the tray for a paper jam or shortage and performing a rain dance in the hopes of attracting the gods' attention xP. In short, I'm at my wits end and don't know where to go from here.
    I'm unable to access the device's LCD display control panel, which controls the printer, as the error message cannot be closed. I've tried restarting the PC as well, and a lot of other basic deductive troubleshooting procedures to no avail (forgive my overuse of cliches).
    Any help would be appreciated. Thank you very much in advance. I wish you all a great day, and may the god of printing protect you from the same situation. I can assure you it's most unpleasant.
    Regards, Sean (frosztbyte)
    P.S. I'm not sure what other information might be needed in order to help me, but ask and you shall receive any I can find.

    Hi frosztbyte,
    I understand your parents have an OfficeJet Pro 8600 that is saying it has a printer failure, that you have thus far not been able to clear, despite your best effort and a rain dance (at least I know who to blame for the rain now ). I would be happy to help you as best I can!
    The first thing I'd suggest you do is plug the printer directly to a wall outlet if it isn't already plugged to one, just to ensure the printer is getting all the power it needs to function properly. If that doesn't seem to change anything though, please have a look through this A 'Printer Failure' Message That Might Include an '0x610000f6' or '0x61xxxxxx' Error Code Displays o... document (it was steps for the same error without an error code as well) and hopefully it can help resolve the issue.
    If the issue persists after trying the wall outlet and that document I would advise you try call HP again. I believe the number you called previously may have not have been HP, but another company. If you're in North America just call 1-800-474-6836, and if you're anywhere else have a look at this Contact HP Worldwide page to see what number to call for your area.
    Hope this helps, have a great day!!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • How do I get my Samsung tablet to print invoices and shipping information

    How do I get my Samsung tablet to print invoices and or shipping labels . Have HP loaded will not print.

    Hi,
    Depending on your printer actually, please use the Google Play/Store search for HP All-In-One Printer Remote or HP ePrint and install on your tablet.
    Hope this helps.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How do I set up my phone to send a file to print from my iphone 5 to my Samsung CLX-4195FW printer?

    How do I set up my phone to send a file to print from my iphone 5 to my Samsung CLX-4195FW printer?

    Read the printer manual.

  • How do I install a samsung clp-315 printer under Lion?

    I have upgraded to Lion. This morning I uninstalled my Samsung CLP-315 printer (I was trouble shooting & thought it would be easy to re-install). When I try to re- install via the system preferences my computer recognises the printer is there and tries to get the software to drive it from
    When I click Add I get this message:
    I have also tried downloading the driver from Samsung's  Web site but I still can't re-install the printer.
    Would appreciate comments/help to get it going again.
    Thanks

    I had this problem with my Samsung CLX3185, For some other reason I had to restart. After that restart when I got around to it again, I could install it. Hope it helps. Also, Samsung printer software update is available via software update. Suggest run the SW update, restart and try again.

  • How to install samsung scx-4200 printer/scanner on Mac OS x 10.9.2?

    How to install samsung scx-4200 printer/scanner on Mac OS x 10.9.2? Several attempts with various downloads from Apple and Samsung sites have failed. Any help is higkly appreciated. Thanks in advance!

    Thias is what I find in system information:
    Samsung Scanner:
      Version:          2.01.12
      Erhalten von:          Apple
      Zuletzt geändert:          10.04.14 21:20
      Art:          Universal
      64-Bit (Intel):          Ja
      Signiert von:          Software Signing, Apple Code Signing Certification Authority, Apple Root CA
      Ort:          /Library/Image Capture/Devices/Samsung Scanner.app
      Informationen:          Copyright (C) 2013 Samsung Electronics Co., Ltd.

  • [SOLVED] CUPS doesn't detect USB Samsung ML-2010 printer

    Hi. I only speak a little English. Sorry for that.
    I have got an USB Samsung ML-2010 printer. Before I used cups-usblp from AUR, and it worked. But it doesn't work now. The cups-usblp maintainer suggests to use cups instead of cups-usblp. Searching with google, it appears that other people don't have problems with this printer, cups, and archlinux. But I do. Cups' web interface doesn't detect it.
    Well, this is how are the things now:
    $ lsusb | grep Samsung
    Bus 002 Device 004: ID 04e8:326c Samsung Electronics Co., Ltd ML-2010P Mono Laser Printer
    $ ls -l /dev/bus/usb/002/004
    crw-rw-r-- 1 root lp 189, 131 mar  4 09:56 /dev/bus/usb/002/004
    $ grep usb /lib/udev/rules.d/50-udev-default.rules
    # 'libusb' device nodes
    SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", MODE="0664"
    SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", IMPORT{builtin}="usb_id"
    SUBSYSTEM=="usb", ENV{DEVTYPE}=="usb_device", ENV{ID_USB_INTERFACES}=="*:0701??:*", GROUP="lp"
    $ sudo grep SystemGroup /etc/cups/cupsd.conf
    SystemGroup sys root lp
    $ groups
    lp wheel games video audio optical storage scanner power users
    $ cat /etc/modprobe.d/blacklist.conf
    blacklist usblp
    $ lsmod | grep usblp
    (no output)
    $ cat /etc/udev/rules.d/10-cups_device_link.rules
    KERNEL=="lp[0-9]", SYMLINK+="%k", GROUP="lp"
    $ cat /etc/udev/rules.d/10-usbprinter.rules
    ATTR{idVendor}=="04e8", ATTR{idProduct}=="326c", MODE:="0660", GROUP:="lp"
    $ rc.d status cupsd
    :: Checking cupsd status                                                                                                   [STARTED]
    $ pacman -Q cups ghostscript gsfonts gutenprint foomatic-db foomatic-db-engine foomatic-db-nonfree foomatic-filters splix
    cups 1.5.2-1
    ghostscript 9.05-1
    gsfonts 1.0.7pre44-3
    gutenprint 5.2.7-3
    foomatic-db 1:4.0.7_20110707-1
    foomatic-db-engine 1:4.0.7_20110707-1
    foomatic-db-nonfree 1:4.0.7_20110707-1
    foomatic-filters 1:4.0.7_20110707-1
    splix 2.0.0-11
    I open http://localhost:631 in my browser, click "add new printer" and I get just "Serial printer #1"
    at "local printers". There isn't my printer. I use KDE, and KDE's tool for adding printers doesn's detect it either.
    I miss archlinux, but I need to print.
    What may be wrong? What may be I am missing?
    Thanks a lot for your comments and help.
    Last edited by felihommen (2012-03-04 20:33:39)

    Solved!
    Restarting cupsd didn't work.
    But reinstalling cups...
    $ sudo pacman -Rdc cups (it is a dependency of kdeadmin-system-config-printer-kde which I had installed)
    $ sudo rm -r /etc/cups/*
    I realize cupsd is already running:
    $ ps aux | grep cupsd
    root      1549  0.0  0.1  75548  4080 ?        Ss   21:04   0:00 cupsd -C /etc/cups/cupsd.conf
    felipe    1690  0.0  0.0   8416  1028 pts/1    S+   21:13   0:00 grep cups
    I kill it
    $ sudo -SIGKILL 1549
    $ ps aux | grep cupsd
    felipe    1694  0.0  0.0   8416  1024 pts/1    S+   21:13   0:00 grep cups
    Ok. Reinstall cups
    $ sudo pacman -S cups
    Start cups daemon:
    $ sudo rc.d start cupsd
    Open firefox. Go to web interface, bla, bla, bla.... And it's there!
    I feel really silly. It was a fresh install, so I didn't think about reinstalling.
    Printed some jobs and worked perfectly. I used the gutenprint driver.
    Thanks a lot, pyther.  I thought yours wasn't a very useful suggestion, but it really was. I'm so happy. I owe you.

  • Mavericks upgrade Xerox C2200 Print issues

    Previous templtes and options on 10.9 setup to print envelopes on the bypass tray on my C2200, upgraded to Mavericks and now envelope printing on the bypass tray printing 90 degrees out. Preview looks fine as it always has before clicking print. Using the Xerox Driver 4.0

    Thanks Carolyn, Xerox support site has to be the slowest in the world... The OS X driver is older than the OS X 10.8 driver, 26/8/2011 vs 29/5/2013, though if you click view other drivers on either you get access to an updated driver dated 26/9/2013... Updated driver hasn't helped.

  • [Solved] Samsung SCX-4300 Printer Problem

    Hi everyone. I installed Arch Linux today. Everything is fine except printer. I am using Samsung SCX-4300 printer and scanner. Scanner works fine but CUPS doesn't see the printer. I can't see anything on CUPS web interface's Local Printers area. Here is a screenshot.
    I can see my printer in lsusb command:
    Bus 002 Device 004: ID 062a:0201 Creative Labs Defender Office Keyboard (K7310) S Zodiak KM-9010
    Bus 002 Device 003: ID 04e8:342e Samsung Electronics Co., Ltd
    Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver
    Bus 001 Device 003: ID 046d:08d7 Logitech, Inc. QuickCam Communicate STX
    Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    So why I can not see my printer and how can I fix that?
    Last edited by DoGuKaN (2013-07-30 20:13:21)

    I have a very similar printer (SCX-4500W) and found that I was able to get it working as a printer but that I could not get both print and scan functions to work at the same time.
    In order to get the printer going I had to add a file to /etc/udev/rules.d/71-scx4500w.rules with the content as a single line:
    ATTR{idVendor}=="04e8", ATTR{idProduct}=="342b", MODE:="0664", GROUP:="lp", ENV{libsane_matched}:="yes"
    You will need to change the idVendor and idProduct in the line above to match that for your own printer from the lsusb command instead of those above for the SCX-4500W.
    I would also suggest that you use the splix drivers package - i.e. make sure that the splix package is installed with:
    # pacman -S splix
    Then when you add the printer select the splix drivers which will work with that printer (you should check the splix support page to check your printer is supported but I am pretty sure it is)
    Once that is done then you need to start the cups.socket daemon with the following command as root (exclude the # which is the prompt)
    # systemctl start cups.socket
    and if it then works, and allows you to add the printer,  then you also need to "enable" the same daemon so that it starts after the next boot as well:
    # systemctl enable cups.socket
    One other thing is that if you want your printer to be discoverable as a cups remote printer on your local network you will need avahi-daemon running on the server to which the printer is attached, as well as on any machine which needs to see it - check the arch wiki on how to set that up if you need it.
    I hope this helps.

Maybe you are looking for