MAX differential measurement does not match DAQ Assistant output
I am using a USB Compact DAQ AI 9205 and have a differential input running into AI23 and AI31.The signal is run to the AI module with a shielded twisted pair cable.
When using MAX, it shows that my signal is at about 4.4 Vdc. An external meter agrees with this reading.
When measured using DAQ Assistant in the VI, the output shows -.5 volts.
Can you tell me what could be causing this?
metzler CLAD
Metzler:
If only one channel is returning erroneous values, it may be possible that there is a malfunction in hardware. In order to confirm/eliminate the possibility, could you test the suspect input with one of the shipping DAQmx examples?
If you open the Example Finder (Help --> Find Examples), browse to "Hardware Input and Output --> DAQmx --> Analog Measurements --> Voltage. I would recommend trying "cont acq&graph voltage-int clk.vi."
Set it to use the suspect channel and compare the reading with your external meter. If they agree, then there's likely an issue with your code somewhere. You'll need to start simple and build up to your current program's implementation complexity to find where the signal is not being passed correctly.
Caleb Harris
National Instruments | Mechanical Engineer | http://www.ni.com/support
Similar Messages
-
Structure Index Member structure imput does not match Input Splitter output
I am running into a problem with Tiger's Quartx Composer where a structure output from an Input Splitter does not match the structure input to the Structure Index Member it is directly connected to. The input to the Structure Index Member displays an unchanging value structure when a changing value structure is passed to it. The same result occurs if the inputted structure in received via publish by passing the Input Splitter. Does anyone know what would cause this to happen?
Hi Frank,
Sorry, I have absolutely no idea what you're dealing with, but have you done any OS Maintenance lately, like clearing Caches?
At this point I think you should get Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
After installing, reboot holding down CMD+s, (+s), then when the DOS like prompt shows, type in...
applejack AUTO
Then let it do all 5 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 5 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
First reboot will be slower, sometimes 2 or 3 restarts will be required for full benefit... my guess is files relying upon other files relying upon other files!
Disconnect the USB cable from any UPS so the system doesn't shut down in the middle of the process. -
Frame rate for camera does not match with AVI output
Hello,
I'm taking a video from a Basler A504K camera of well plate bottoms deflecting down. I have a frame rate indicator from the Vision Acquisition to see at what fps the camera is acquiring images, and I also have a frame rate controller at the IMAQ AVI Create VI.
The problem is when I set the frame rate at the Create VI. The higher I set the frame rate, the fewer frames it seems to take. For example when I play the videos on Windows Media Player, at 10fps, the video length is 60s. At 100fps, the video length is 6s. At 20fps, it's 30s, and at 50fps, it's 12s. Obviously, the video length decreasing by the factor by which I increase the fps. But since higher frames per second videos show a slower/longer videos, since they have more images to display per second?
I need to be able to see a slow increase and decrease in the well deflections smoothly. At high frame rates, the video goes by so fast that I cannot analyze the deflections. At low frame rates, the video is slower, but there are too many missing frames so the deflection is not smooth (ie. you see no deflection one second, and the next, you see the peak deflection without seeing the gradual increase in deflections). It is very hard to find an "ideal" frame rate, so I was wondering if there was another way to control the frame rate such that I have high fps, and longer video lengths?
I'm attaching my VI. The bottom loop is where all the Video and Camera controls are. The top loops is to control pressure gauge and valve (just ignore that loop)
Thank you,
B.J. Kim
University of Michigan
Attachments:
Injury_Pressure_PulseFINAL_AVI.vi 174 KBHi B.J. Kim,
The problem you're seeing with the fps and video length makes sense to me. If you keep the overall frame count constant and change only the rate of playback, then the video time will be indirectly proportional, as you have noticed. Just from simple math, it appears like you kept the video image at a constant of 600 total frames while changing the frame rate between 10, 20, 30fps, etc. If you're looking to have more resolution in you video, maybe you could increase the actual frame rate of acqusition from your camera. You may also try placing a small millisecond wait in your while loop to slow down execution speed. -
How can I downloade a trial of Adobe Elements 12?
I followed the instructions to download assistant...but get this message: The application cannot be installed due to a certificate problem. The certificate does not match the installed application certificate, does not support application upgrades, or is invalid. Please contact the application author.Hi alposer,
Please remove the copy of the Adobe Download Assistant you currently have installed and then reinstall the Adobe Download Assistant.
Regards,
Rave -
Please assist I am on a Windows 7 64 bit machine I have VS 2010 and have been fighting with this new program that I was brought on to help with - Issue is that I am unable to get rid of this issue. There is so many solutions but none have worked. If someone can give me some help with what has worked for you.
The error is Could not load file or assembly 'log4net, Version=1.2.10.0, Culture=neutral, PublicKeyToken=692fbea5521e1304' or one of its dependencies. The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040)
This is with CR installed on 64 bit.
Thank you very much for any assistance with this problem,
KrisHi Vittorio
Please enter the search string 'log4net crystal net' into the search box in the top right corner. When the results come up, click on the Support Notes link. That will filter for the KBAs that you want to have a look at.
- Ludek
Senior Support Engineer AGS Product Support, Global Support Center Canada
Follow us on Twitter -
Your credit card does not match your bank's records
your credit card does not match your bank's records. appears at purchase in itunes store.
2 months with no solution on this. Nothing has changed with my bank at all. Yet apple was able to bill the same card for my mobile me acct. so the card does in fact work! I emailed and got what I already knew. see below, then my reply.
Dear Eric,
You can change your iTunes Store billing information at any time. When you update your credit card number or billing address through the iTunes Store, any equivalent information you might use with MobileMe, iPhoto, Aperture, or the Apple Store online is also updated.
To update your billing address or credit card number, follow these steps:
1) Make sure you're using the latest version of iTunes. It can be downloaded free of charge from the Apple website:
http://www.apple.com/itunes/download
Eric, installing the latest version of iTunes will not affect your library or any items in your account that you haven't downloaded.
2) Click this link: http://phobos.apple.com/accountSummary
iTunes will automatically launch and the sign-in dialog will appear.
3) If you are not already signed in, you will need to enter your iTunes Store account name and password and then click the Account Info button.
4) On your Apple Account Information page, click Edit Payment Information
Make the necessary changes. Your billing address should be exactly the same as the address on your credit card statement and with the United States Postal Service (click "Find a ZIP Code" at http://www.usps.com and follow the onscreen instructions). This is important, because even differences in punctuation, abbreviation, and capitalization can cause payment errors that might prevent you from using the iTunes Store.
5) When all of the information is up to date, click Done.
When you update your billing information, the iTunes Store places an authorization hold on your credit card to verify your account information. You might see this authorization request on your online statement. This is not an actual charge; it is simply a test to confirm that your credit card account is active and has credit available to accommodate transactions.
Authorization requests are automatically removed from your account by your financial institution. The amount of time it takes to remove authorization requests varies by financial institution. If you have any questions about the way your financial institution handles authorization requests, please contact their customer-service department.
Thank you for your time. If you have any other questions or concerns, regarding your iTunes Store account, Eric, please feel free to reply to this email. Have a great day.
Sincerely,
Timothy
iTunes Store Customer Support
http://www.apple.com/support/itunes/ww/
Please Note:I work Sunday 9:00 to 6:00 Tuesday and wednesday 9:00 to 6:00 Friday and Saturday 9:00 to 6:00 Central Standard Time
Thank you for allowing me the opportunity to assist you. You may receive an AppleCare survey email; any feedback you provide would be greatly appreciated.
My reply
I've read the support pages through and through and have gone through all of these steps in the past. Nothing on my end has changed. This card has been used for approx three years now, never to have been edited. As stated... In the midst of all of this difficulty, you were able to bill the same card for my mobile me subscription. Which should technically not gone through due to the supposed billing info not matching my bank's records! So quite simply, my card does work, this is something on your end, not my bank.
And I did however change the type case to match my statement to no avail. This never made a difference in the past, but I tried it regardless.
After attempting things for two months, I am growing tired of trying to spend my money on Apple. I will try one more suggestion if one is available. After that, I have had great success with the amazon store and may have to flip over to them. My time is way too valuable to be troubleshooting a problem I did not create.
any specific help would be appreciated (please do not copy and paste tips from the support pages... been there)
EricAs a follow up to my last post, I thought I would offer you my customer service experience as I am hoping you can avoiding going through what I've been through and that this will save you some time.
I'm listing the discourse chronologically for your convenience:
Specific request: My credit card or billing information is not accepted
Details:
iTunes says my credit card information does not match my bank information and will not let me make purchases. I have updated my account information and I still cannot make purchases. I get the same message that my card does not match my bank's information- which it does.
Please help.
TrackID: 1--------------
Dear ----------,
Welcome to Apple iTunes Store Customer Support. My name is Snehashish.
I am sorry to hear that you haven't been able to make purchases on the iTunes Store with your credit card. I know this is frustrating, and I will try to provide as much information as I can to help you resolve it.
-----------, upon checking your account I find your credit card will be expired after this month. So you have to change it then. I suggest you to change it now or contact your credit card company as it is declined by iTunes.
The iTunes Store has been unable to verify an authorization from your credit card company. There are several possible reasons for this:
- Your credit card company's servers may have been busy. Trying again later may resolve the issue.
- Your card may not have been activated yet. If so, you will need to activate it.
- You may need to call your credit card company before the authorization is approved.
- You may need to ensure that you correctly located the credit card's security code. To see instructions for locating the security code, choose View My Account from the iTunes Store menu, sign in to your account, click Edit Payment Information, and then click the "What is this?" link next to the Security Code field.
- Your billing name or address does not match the address listed on your credit card statement. Any discrepancy in punctuation, abbreviation, or capitalization can cause errors, which might prevent you from purchasing from the iTunes Store. If you moved, or if your zip code changed recently, ask your credit card company to make sure its records are up to date and match exactly what you are entering as your billing information.
--------, please follow these steps to confirm or update your account information:
1) Go to the My Apple ID site at:
http://appleid.apple.com/
2) If the site is not displayed in your preferred language, click the Change Language link in the upper-right corner, type the name of your language in the field that appears, then click the Save button.
3) Click the "Manage your account" link.
4) Type your iTunes Store account name (which is your Apple ID) in the Apple ID field, type your password in the password field, then click the Sign In button.
5) Click "Addresses" in the left column.
6) Confirm or edit your information.
7) Click "Phone Numbers" on the left. Make sure the area codes and phone numbers are entered correctly in their respective fields.
8) Click Save Changes.
Once your information is updated, try placing an order on the iTunes Store again. If the iTunes Store still cannot obtain an authorization for your card, it means that your billing information is still incorrect, either with your credit card company or with its verification system, which may be handled by another company.
Fortunately, you may be able to make iTunes Store purchases with another payment method. For example, if PayPal accepts your credit card, you can use your PayPal account to buy from the iTunes Store. If you need more information about using PayPal on the iTunes Store, please let me know.
------, I hope this information is helpful. Thank you for your interest; I am pleased that you want to be an iTunes Store customer. Have a great day!
Sincerely,
Snehashish
iTunes Store Customer Support
Thank you for allowing me the opportunity to assist you. You may receive an AppleCare survey email; any feedback you provide would be greatly appreciated.
Follow-Up: 1----------------
Hello again,
I wanted to send a quick note to see if you are still experiencing any difficulties with the iTunes Store. Resolving your issue is important to me, so please don't hesitate to reply if you need any further assistance.
Sincerely,
Snehashish
iTunes Store Customer Support
Greetings Snehashish,
When I wrote my original ticket it was to address the issue of the fact I had already updated my credit card information and I was still receiving the error message of "my credit card not matching my bank information" in iTunes. Giving me instructions on how to update my account information was not helpful because I had already taken that step. So, no, my problem remains unresolved and I am unable to make any purchases in iTunes or update my iPhone.
Luckily, the item I was looking to purchase was available on Amazon digitally so I went ahead and bought it there without any problem whatsoever with my credit card- furthering the mystery and the enigma that is iTunes rejection of my credit card.
Please send the next step to resolve my issue or please forward my ticket to someone who can resolve this for me.
Thank you,
Dear ------------,
Welcome back to Apple iTunes Store Customer Support. This is Snehashish again.
I am glad to hear that your credit card works on another website. Some of our customer resolves this type of issue by removing credit card from their account, buy a free app and then re-add the credit card to account. I suggest you to try that.
---------, please delete the credit card information from your account:
1) Open iTunes and sign in to the iTunes Store.
2) Select "View My Account" from the Store menu.
3) Enter your password and click the View Account button.
4) Click the Edit Payment Information button.
5) Select "None" as the payment type.
6) Click the Done button at the bottom of the page.
After you select the "None" option, please attempt to download a free App from iTunes Store. Then sign out from your account and sign in back and re-add your credit card information.
--------, then, please follow these steps to confirm or update your account's information:
1) Go to the My Apple ID site at:
http://appleid.apple.com/
2) If the site is not displayed in your preferred language, click the Change Language link in the upper-right corner, type the name of your language in the field that appears, then click the Save button.
3) Click the "Manage your account" link.
4) Type your iTunes Store account name (which is your Apple ID) in the Apple ID field, type your password in the password field, then click the Sign In button.
5) Click "Addresses" in the left column.
6) Confirm or edit your information.
7) Click "Phone Numbers" on the left. Make sure the area codes and phone numbers are entered correctly in their respective fields.
8) Click Save Changes.
Once your information is updated, try placing an order on the iTunes Store again.
If you have further questions or concerns, please feel free to contact me again. Have a nice day, ----------!
Hello again Snehashish,
My address is confirmed and matches my bank account. I followed the steps as you directed with deleting my information downloading the free application and then re-entering my payment information. I continue get the error message that my credit card information does not match my bank's records. I have as of today called the bank and confirmed twice that my banking address is correct. The error is not happening on the banking side of the equation.
Please send the next step to resolve my issue or please forward my ticket to someone who can resolve this for me.
Thank you very much,
Dear -------,
Welcome back to Apple iTunes Store Customer Support. This is Snehashish again.
Thank you for your response. Upon reviewing your account I find you removed that credit card successfully. I suggest you to update that information to start purchasing. You can also use gift card as well.
--------, you can change your iTunes Store billing information at any time. When you update your credit card number or billing address through the iTunes Store, any equivalent information you might use with MobileMe, iPhoto, Aperture, or the Apple Store online is also updated.
To update your billing address or credit card number, follow these steps:
1) Make sure you're using the latest version of iTunes. It can be downloaded free of charge from the Apple website:
http://www.apple.com/itunes/download
Note: Installing the latest version of iTunes will not affect your library or any items in your account that you haven't downloaded.
2) Click this link: <link to launch itunes>
iTunes will automatically launch and the sign-in dialog will appear.
3) If you are not already signed in, you will need to enter your iTunes Store account name and password and then click the Account Info button.
4) On your Apple Account Information page, click Edit Payment Information
Make the necessary changes. Your billing address should be exactly the same as the address on your credit card statement and with the United States Postal Service (click "Find a ZIP Code" at http://www.usps.com and follow the onscreen instructions). This is important, because even differences in punctuation, abbreviation, and capitalization can cause payment errors that might prevent you from using the iTunes Store.
5) When all of the information is up to date, click Done.
When you update your billing information, the iTunes Store places an authorization hold on your credit card to verify your account information. You might see this authorization request on your online statement. This is not an actual charge; it is simply a test to confirm that your credit card account is active and has credit available to accommodate transactions.
Authorization requests are automatically removed from your account by your financial institution. The amount of time it takes to remove authorization requests varies by financial institution. If you have any questions about the way your financial institution handles authorization requests, please contact their customer-service department.
---------, if you have further questions or concerns, please feel free to contact me again. Have a nice day!
Despite already having the current version of iTunes, I re-downloaded the program and installed it on my computer. I logged into the link you sent me. I entered in my banking (again and without mistake) information exactly as it is on my billing information. I have now entered my credit card information correctly on iTunes repeatedly- it has not deviated nor changed and there has never been a mistake in my data entry. I have used this credit card at other locations and online stores without error and my banking and credit card information is correct.
I entered a credit card I DO NOT want to use in conjunction with my iTunes account and it was accepted without incident or error message. The problem is that the card I do want to use, that I NEED to use to make purchases on iTunes is not accepted. Both cards are issued through the same bank- one is debit and one is credit and they both link to the same bank account with the same home address. The debit card is being rejected and the credit card is accepted. My problem is not my address nor the account number as both have been entered correctly multiple times. iTunes is rejecting my particular card even though it is working and matches my bank information. This is the card I have always used to make purchases on iTunes and this error started when my old card expired and I attempted to update my account.
Every time I re-enter my credit card and try to make a purchase and I always get the following message:
"There are errors or omissions in the information. Please correct the indicated items: Your credit card does not match your bank's records. Please enter a US credit card and a matching billing address."
I have reset, re-downloaded, and re-entered everything on my end multiple times resulting in the same error from iTunes. I want to know what is happening with my account. If you do not have a solution then please escalate this ticket and please put me in contact with someone who can help me.
Thank you for your time,
I found my solution in the Apple Support Community. It had nothing to do with my information being incorrect. I do not require your assistance any longer.
My issue resolution was actual very simple and came from this page. iTunes has a bug where it will not accept your information but if you add your credit card under you account in the Apple Store and CONFIRM then it will appear in your iTunes account automatically. I could have saved hours of email, calls to the bank and stupid angst if I had looked this up instead of TRYING to use Apple Customer Support. I've learned my lesson. I just want you to know that iTunes is bugged and broken in this respect and no matter how many times you enter your information IT DOESN'T WORK. I hope this helps someone else.
Apple please tell your customer support people how to actually help instead of having them paste in worthless form letters on how to use a credit card with iTunes. Obviously it iTunes that is broken.
PLEASE FIX. -
[Solved] (WW) fglrx(0): Kernel Module version does *not* match driver.
fglrx has just recently stopped working, and I can't quite pinpoint when that was because I honestly hadn't noticed until checking. I've tried a few reinstalls and different xorg options so far, but had no luck.
glxinfo:
name of display: :0.0
display: :0 screen: 0
direct rendering: No
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
GLX_EXT_import_context, GLX_EXT_texture_from_pixmap, GLX_OML_swap_method,
GLX_SGI_make_current_read, GLX_SGIS_multisample, GLX_SGIX_hyperpipe,
GLX_SGIX_swap_barrier, GLX_SGIX_fbconfig, GLX_MESA_copy_sub_buffer
client glx vendor string: ATI
client glx version string: 1.3
client glx extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_get_proc_address, GLX_SGI_video_sync, GLX_ARB_multisample,
GLX_ATI_pixel_format_float, GLX_ATI_render_texture
GLX version: 1.2
GLX extensions:
GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
GLX_ARB_multisample
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.4 (1.5 Mesa 6.5.2)
OpenGL extensions:
GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_texture_border_clamp,
GL_ARB_texture_cube_map, GL_ARB_texture_env_add,
GL_ARB_texture_env_combine, GL_ARB_texture_env_dot3,
GL_ARB_transpose_matrix, GL_EXT_abgr, GL_EXT_blend_color,
GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_texture_env_add,
GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
GL_EXT_texture_lod_bias
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
0x23 24 tc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x24 24 tc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x25 24 tc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x26 24 tc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x27 24 dc 0 24 0 r y . 8 8 8 0 0 16 0 0 0 0 0 0 0 None
0x28 24 dc 0 24 0 r y . 8 8 8 0 0 16 8 16 16 16 0 0 0 None
0x29 24 dc 0 32 0 r y . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
0x2a 24 dc 0 32 0 r . . 8 8 8 8 0 16 8 16 16 16 16 0 0 None
Xorg.0.log:
X Window System Version 7.2.0
Release Date: 22 January 2007
X Protocol Version 11, Revision 0, Release 7.2
Build Operating System: UNKNOWN
Current Operating System: Linux yggdrasil 2.6.21-ARCH #1 SMP PREEMPT Mon Jun 11 23:47:51 CEST 2007 i686
Build Date: 08 April 2007
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Wed Jul 11 10:14:15 2007
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Xorg"
(**) |-->Screen "Screen0" (0)
(**) | |-->Monitor "Monitor0"
(**) | |-->Device "Card0"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbRules" "xorg"
(**) XKB: rules: "xorg"
(**) Option "XkbModel" "pc105"
(**) XKB: model: "pc105"
(**) Option "XkbLayout" "gb"
(**) XKB: layout: "gb"
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "mx518"
(**) FontPath set to:
/usr/share/fonts/misc:unscaled,
/usr/share/fonts/misc,
/usr/share/fonts/75dpi:unscaled,
/usr/share/fonts/75dpi,
/usr/share/fonts/100dpi:unscaled,
/usr/share/fonts/100dpi,
/usr/share/fonts/cyrillic,
/usr/share/fonts/Type1,
/usr/share/fonts/TTF
(**) RgbPath set to "/usr/share/X11/rgb"
(**) ModulePath set to "/usr/lib/xorg/modules"
(**) Option "AllowMouseOpenFail" "true"
(**) Option "AIGLX" "off"
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(II) No APM support in BIOS or kernel
(II) Loader magic: 0x81c44a0
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.3
X.Org Video Driver: 1.1
X.Org XInput driver : 0.7
X.Org Server Extension : 0.3
X.Org Font Renderer : 0.5
(II) Loader running on linux
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/xorg/modules//libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(++) using VT number 7
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,0269 card 1043,8122 rev 80 class 06,00,00 hdr 80
(II) PCI: 00:00:1: chip 1106,1269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:2: chip 1106,2269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:3: chip 1106,3269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:4: chip 1106,4269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:00:7: chip 1106,7269 card 1043,8122 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b198 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:0a:0: chip 1102,0004 card 1102,2002 rev 04 class 04,01,00 hdr 80
(II) PCI: 00:0a:1: chip 1102,7003 card 1102,0040 rev 04 class 09,80,00 hdr 80
(II) PCI: 00:0a:2: chip 1102,4001 card 1102,0010 rev 04 class 0c,00,10 hdr 80
(II) PCI: 00:0e:0: chip 1317,0985 card 1317,0574 rev 11 class 02,00,00 hdr 00
(II) PCI: 00:0f:0: chip 1106,3149 card 1043,80ed rev 80 class 01,04,00 hdr 80
(II) PCI: 00:0f:1: chip 1106,0571 card 1043,80ed rev 06 class 01,01,8a hdr 00
(II) PCI: 00:10:0: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:2: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3038 card 1106,3038 rev 81 class 0c,03,00 hdr 80
(II) PCI: 00:10:4: chip 1106,3104 card 1106,3104 rev 86 class 0c,03,20 hdr 80
(II) PCI: 00:11:0: chip 1106,3227 card 1043,80ed rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:5: chip 1106,3059 card 1043,810d rev 60 class 04,01,00 hdr 00
(II) PCI: 00:11:6: chip 1106,3068 card 0000,0000 rev 80 class 07,80,00 hdr 00
(II) PCI: 01:00:0: chip 1002,4e48 card 1002,0002 rev 00 class 03,00,00 hdr 80
(II) PCI: 01:00:1: chip 1002,4e68 card 1002,0003 rev 00 class 03,80,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000b (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000d000 - 0x0000dfff (0x1000) IX[b]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xfd900000 - 0xfdefffff (0x600000) MX[b]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0x9ff00000 - 0xbfefffff (0x20000000) MX[b]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) ATI Technologies Inc Radeon R350 [Radeon 9800 Pro] rev 0, Mem @ 0xb0000000/27, 0xfde00000/16, I/O @ 0xd000/8, BIOS @ 0xfdd00000/17
(--) PCI: (1:0:1) ATI Technologies Inc Radeon R350 [Radeon 9800 Pro] (Secondary) rev 0, Mem @ 0xa8000000/27, 0xfdc00000/16
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
(II) OS-reported resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xe7ffffff to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[1] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[2] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[3] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[4] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[5] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[6] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[7] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[8] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[9] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[10] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[11] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[12] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[13] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[14] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[15] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[17] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[18] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[19] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[20] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[21] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[22] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[23] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[24] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[25] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[26] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[1] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[2] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[3] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[4] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[5] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[6] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[7] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[8] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[9] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[10] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[11] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[12] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[13] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[14] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[15] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[17] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[18] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[19] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[20] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[21] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[22] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[23] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[24] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[25] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[26] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
(II) All system resource ranges:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[16] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[17] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[18] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[19] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[20] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[21] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[23] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[24] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[25] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[26] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[27] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[28] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[29] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[30] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[31] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[32] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) LoadModule: "ddc"
(II) Loading /usr/lib/xorg/modules//libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension XFree86-DRI
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(**) AIGLX disabled
(II) Loading extension GLX
(II) LoadModule: "type1"
(II) Loading /usr/lib/xorg/modules/fonts//libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font Type1
(II) LoadModule: "freetype"
(II) Loading /usr/lib/xorg/modules/fonts//libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 7.2.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.5
(II) Loading font FreeType
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.13.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension RECORD
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 1.0
(II) LoadModule: "fglrx"
(II) Reloading /usr/lib/xorg/modules/drivers//fglrx_drv.so
(II) LoadModule: "keyboard"
(II) Loading /usr/lib/xorg/modules/input//keyboard_drv.so
(II) Module keyboard: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/lib/xorg/modules/input//mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.1.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.7
(II) Primary Device is: PCI 01:00:0
(II) ATI Proprietary Linux Driver Version Identifier:8.38.6
(II) ATI Proprietary Linux Driver Release Identifier: LGDr8.38g1
(II) ATI Proprietary Linux Driver Build Date: Jun 22 2007 13:10:21
(II) ATI Proprietary Linux Driver Build Information: autobuild-rel-r6-8.38.1.1.2.3-driver-lnx-x86-x86_64-351593
(--) Assigning device section with no busID to primary device
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found
(--) Chipset Supported AMD Graphics Processor (0x4E48) found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[16] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[17] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[18] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[19] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[20] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[21] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[22] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[23] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[24] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[25] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[26] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[27] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[28] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[29] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[30] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[31] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[32] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
(II) fglrx(0): pEnt->device->identifier=0x81e4088
(II) resource ranges after probing:
[0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[4] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[5] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[6] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[7] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[8] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[9] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[10] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[11] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[12] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[13] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[14] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
[15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
[16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
[17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[18] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[19] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[20] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[21] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[22] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[23] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[24] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[25] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[26] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[27] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[28] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[29] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[30] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[31] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[32] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[33] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[34] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[35] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
[36] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
[37] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
(II) Setting vga for screen 0.
(II) fglrx(0): === [atiddxPreInit] === begin, [x]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.1
(II) fglrx(0): PCI bus 1 card 0 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "DPMS" "true"
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(==) fglrx(0): Gamma Correction for I is 0x06419064
(==) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/xorg/modules//libint10.so
(II) Module int10: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 1.1
(WW) fglrx(0): Bad V_BIOS checksum
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(--) fglrx(0): Chipset: "RADEON 9800 PRO" (Chipset = 0x4e48)
(--) fglrx(0): (PciSubVendor = 0x1002, PciSubDevice = 0x0002)
(--) fglrx(0): board vendor info: original ATI graphics adapter
(--) fglrx(0): Linear framebuffer (phys) at 0xb0000000
(--) fglrx(0): MMIO registers at 0xfde00000
(==) fglrx(0): ROM-BIOS at 0x000c0000
(II) Loading sub module "vbe"
(II) LoadModule: "vbe"
(II) Loading /usr/lib/xorg/modules//libvbe.so
(II) Module vbe: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.1.0
ABI class: X.Org Video Driver, version 1.1
(II) fglrx(0): VESA BIOS detected
(II) fglrx(0): VESA VBE Version 2.0
(II) fglrx(0): VESA VBE Total Mem: 16384 kB
(II) fglrx(0): VESA VBE OEM: ATI R360
(II) fglrx(0): VESA VBE OEM Software Rev: 1.0
(II) fglrx(0): VESA VBE OEM Vendor: ATI Technologies Inc.
(II) fglrx(0): VESA VBE OEM Product: R360
(II) fglrx(0): VESA VBE OEM Product Rev: 01.00
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
ABI class: X.Org Server Extension, version 0.3
(--) fglrx(0): VideoRAM: 131072 kByte, Type: DDR SGRAM / SDRAM
(II) fglrx(0): AGP card detected
(II) fglrx(0): board/chipset is supported by this driver (original ATI board)
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/lib/xorg/modules//libddc.so
(II) fglrx(0): Connected Display1: DFP on internal TMDS [tmds1]
(II) fglrx(0): Display1 EDID data ---------------------------
(II) fglrx(0): Manufacturer: AIC Model: 9450 Serial#: 329
(II) fglrx(0): Year: 2006 Week: 33
(II) fglrx(0): EDID Version: 1.3
(II) fglrx(0): Digital Display Input
(II) fglrx(0): Max H-Image Size [cm]: horiz.: 37 vert.: 30
(II) fglrx(0): Gamma: 2.20
(II) fglrx(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) fglrx(0): First detailed timing not preferred mode in violation of standard!(II) fglrx(0): redX: 0.647 redY: 0.346 greenX: 0.298 greenY: 0.591
(II) fglrx(0): blueX: 0.150 blueY: 0.118 whiteX: 0.313 whiteY: 0.329
(II) fglrx(0): Supported VESA Video Modes:
(II) fglrx(0): 720x400@70Hz
(II) fglrx(0): 640x480@60Hz
(II) fglrx(0): 640x480@67Hz
(II) fglrx(0): 640x480@72Hz
(II) fglrx(0): 640x480@75Hz
(II) fglrx(0): 800x600@56Hz
(II) fglrx(0): 800x600@60Hz
(II) fglrx(0): 800x600@72Hz
(II) fglrx(0): 800x600@75Hz
(II) fglrx(0): 832x624@75Hz
(II) fglrx(0): 1024x768@60Hz
(II) fglrx(0): 1024x768@70Hz
(II) fglrx(0): 1024x768@75Hz
(II) fglrx(0): 1280x1024@75Hz
(II) fglrx(0): 1152x870@75Hz
(II) fglrx(0): Manufacturer's mask: 0
(II) fglrx(0): Supported Future Video Modes:
(II) fglrx(0): #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) fglrx(0): #1: hsize: 1280 vsize 1024 refresh: 70 vid: 35457
(II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 72 vid: 35969
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 135.0 MHz Image Size: 376 x 301 mm
(II) fglrx(0): h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
(II) fglrx(0): v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 25.2 MHz Image Size: 376 x 301 mm
(II) fglrx(0): h_active: 640 h_sync: 656 h_sync_end 752 h_blank_end 800 h_border: 0
(II) fglrx(0): v_active: 350 v_sync: 387 v_sync_end 389 v_blanking: 449 v_border: 0
(II) fglrx(0): Ranges: V min: 50 V max: 75 Hz, H min: 30 H max: 80 kHz, PixClock max 140 MHz
(II) fglrx(0): Monitor name: F-419
(II) fglrx(0): EDID (in hex):
(II) fglrx(0): 00ffffffffffff000523509449010000
(II) fglrx(0): 2110010380251e78e8e595a5584c9726
(II) fglrx(0): 1e5054bfef808180818a818c01010101
(II) fglrx(0): 010101010101bc34009851002a403070
(II) fglrx(0): 1300782d1100001ed60980a0205e6310
(II) fglrx(0): 10605208782d1100001a000000fd0032
(II) fglrx(0): 4b1e500e000a202020202020000000fc
(II) fglrx(0): 00462d3431390a2020202020202000ba
(II) fglrx(0): End of Display1 EDID data --------------------
(WW) fglrx(0): Only one display is connnected,so single mode is enabled
(II) fglrx(0): Primary Controller - DFP on internal TMDS
(II) fglrx(0): Internal Desktop Setting: 0x00000001
(II) fglrx(0): POWERplay not supported on this hardware
(==) fglrx(0): Qbs disabled
(==) fglrx(0): FAST_SWAP disabled
(==) fglrx(0): PseudoColor visuals disabled
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(==) fglrx(0): Center Mode is disabled
(==) fglrx(0): TMDS coherent mode is enabled
(II) fglrx(0): Total of 37 modes found for primary display.
(--) fglrx(0): Virtual size is 1280x1024 (pitch 0)
(**) fglrx(0): *Mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1280x1024" 135.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 128.9 MHz (scaled from 0.0 MHz), 74.6 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1280x1024" 128.94 1280 1368 1504 1728 1024 1025 1028 1066 +hsync
(**) fglrx(0): Default mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x1024" 108.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 85.5 MHz (scaled from 0.0 MHz), 50.9 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 85.51 1280 1344 1480 1680 1024 1025 1028 1083 interlace +hsync
(**) fglrx(0): Default mode "1280x1024": 77.8 MHz (scaled from 0.0 MHz), 46.3 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 77.80 1280 1344 1480 1680 1024 1025 1028 1077 interlace +hsync
(**) fglrx(0): *Mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800
(**) fglrx(0): Default mode "1024x768": 78.4 MHz (scaled from 0.0 MHz), 57.7 kHz, 72.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.43 1024 1080 1192 1360 768 769 772 801 +hsync
(**) fglrx(0): Default mode "1024x768": 75.0 MHz (scaled from 0.0 MHz), 56.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync
(**) fglrx(0): *Mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
(II) fglrx(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625
(**) fglrx(0): Default mode "800x600": 50.0 MHz (scaled from 0.0 MHz), 48.1 kHz, 72.0 Hz
(II) fglrx(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666
(**) fglrx(0): Default mode "800x600": 45.5 MHz (scaled from 0.0 MHz), 43.8 kHz, 70.0 Hz
(II) fglrx(0): Modeline "800x600" 45.50 800 840 920 1040 600 601 604 625 +hsync
(**) fglrx(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.0 Hz
(II) fglrx(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
(**) fglrx(0): Default mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.0 Hz
(II) fglrx(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
(**) fglrx(0): Default mode "800x600": 29.6 MHz (scaled from 0.0 MHz), 29.8 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "800x600" 29.60 800 816 896 992 600 601 604 635 interlace +hsync
(**) fglrx(0): *Mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.9 kHz, 72.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 664 704 832 480 489 492 520 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x480" 25.18 640 656 752 800 480 490 492 525 +hsync +vsync
(**) fglrx(0): Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900
(**) fglrx(0): Default mode "1152x864": 96.8 MHz (scaled from 0.0 MHz), 63.0 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1152x864" 96.76 1152 1224 1344 1536 864 865 868 900 +hsync
(**) fglrx(0): Default mode "1152x864": 81.6 MHz (scaled from 0.0 MHz), 53.7 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 +hsync
(**) fglrx(0): Default mode "1152x864": 64.7 MHz (scaled from 0.0 MHz), 43.0 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 64.67 1152 1208 1328 1504 864 865 868 915 interlace +hsync
(**) fglrx(0): Default mode "1152x864": 58.3 MHz (scaled from 0.0 MHz), 39.2 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 58.28 1152 1200 1320 1488 864 865 868 911 interlace +hsync
(**) fglrx(0): Default mode "1024x480": 38.2 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x480" 38.16 1024 1048 1152 1280 480 481 484 497 +hsync
(**) fglrx(0): Default mode "848x480": 31.5 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "848x480" 31.48 848 864 952 1056 480 481 484 497 +hsync
(**) fglrx(0): Default mode "720x576": 32.7 MHz (scaled from 0.0 MHz), 35.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x576" 32.66 720 744 816 912 576 577 580 597 +hsync
(**) fglrx(0): Default mode "720x480": 26.7 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x480" 26.71 720 736 808 896 480 481 484 497 +hsync
(**) fglrx(0): Default mode "640x400": 28.1 MHz (scaled from 0.0 MHz), 33.7 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x400" 28.07 640 696 736 832 400 413 415 449
(**) fglrx(0): Default mode "640x400": 24.9 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x400" 24.92 640 664 760 792 400 460 462 525
(**) fglrx(0): Default mode "640x350": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "640x350" 25.18 640 656 752 800 350 387 389 449 +vsync
(**) fglrx(0): Default mode "512x384": 19.8 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "512x384" 19.81 512 544 624 664 384 451 453 497
(**) fglrx(0): Default mode "400x300": 24.8 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 24.75 400 408 448 528 300 601 602 625 doublescan
(**) fglrx(0): Default mode "400x300": 22.3 MHz (scaled from 0.0 MHz), 45.0 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 22.33 400 416 480 496 300 601 605 742 doublescan
(**) fglrx(0): Default mode "320x240": 15.8 MHz (scaled from 0.0 MHz), 37.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 15.75 320 328 360 416 240 481 482 501 doublescan
(**) fglrx(0): Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 12.59 320 328 376 400 240 491 493 525 doublescan
(**) fglrx(0): Default mode "320x200": 13.1 MHz (scaled from 0.0 MHz), 31.5 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 13.10 320 352 368 416 200 406 407 417 doublescan
(**) fglrx(0): Default mode "320x200": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 12.59 320 336 384 400 200 457 459 524 doublescan
(--) fglrx(0): Display dimensions: (370, 300) mm
(--) fglrx(0): DPI set to (87, 86)
(--) fglrx(0): Virtual size is 1280x1024 (pitch 1280)
(**) fglrx(0): *Mode "1280x1024": 135.0 MHz (scaled from 0.0 MHz), 80.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1280x1024" 135.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 128.9 MHz (scaled from 0.0 MHz), 74.6 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1280x1024" 128.94 1280 1368 1504 1728 1024 1025 1028 1066 +hsync
(**) fglrx(0): Default mode "1280x1024": 108.0 MHz (scaled from 0.0 MHz), 64.0 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1280x1024" 108.00 1280 1328 1440 1688 1024 1025 1028 1066
(**) fglrx(0): Default mode "1280x1024": 85.5 MHz (scaled from 0.0 MHz), 50.9 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 85.51 1280 1344 1480 1680 1024 1025 1028 1083 interlace +hsync
(**) fglrx(0): Default mode "1280x1024": 77.8 MHz (scaled from 0.0 MHz), 46.3 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1280x1024" 77.80 1280 1344 1480 1680 1024 1025 1028 1077 interlace +hsync
(**) fglrx(0): *Mode "1024x768": 78.8 MHz (scaled from 0.0 MHz), 60.0 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.75 1024 1040 1136 1312 768 769 772 800
(**) fglrx(0): Default mode "1024x768": 78.4 MHz (scaled from 0.0 MHz), 57.7 kHz, 72.0 Hz
(II) fglrx(0): Modeline "1024x768" 78.43 1024 1080 1192 1360 768 769 772 801 +hsync
(**) fglrx(0): Default mode "1024x768": 75.0 MHz (scaled from 0.0 MHz), 56.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 +hsync +vsync
(**) fglrx(0): Default mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 +hsync +vsync
(**) fglrx(0): *Mode "800x600": 49.5 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz
(II) fglrx(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625
(**) fglrx(0): Default mode "800x600": 50.0 MHz (scaled from 0.0 MHz), 48.1 kHz, 72.0 Hz
(II) fglrx(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666
(**) fglrx(0): Default mode "800x600": 45.5 MHz (scaled from 0.0 MHz), 43.8 kHz, 70.0 Hz
(II) fglrx(0): Modeline "800x600" 45.50 800 840 920 1040 600 601 604 625 +hsync
(**) fglrx(0): Default mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.0 Hz
(II) fglrx(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
(**) fglrx(0): Default mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.0 Hz
(II) fglrx(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625
(**) fglrx(0): Default mode "800x600": 29.6 MHz (scaled from 0.0 MHz), 29.8 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "800x600" 29.60 800 816 896 992 600 601 604 635 interlace +hsync
(**) fglrx(0): *Mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 31.5 MHz (scaled from 0.0 MHz), 37.9 kHz, 72.0 Hz
(II) fglrx(0): Modeline "640x480" 31.50 640 664 704 832 480 489 492 520 +hsync +vsync
(**) fglrx(0): Default mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x480" 25.18 640 656 752 800 480 490 492 525 +hsync +vsync
(**) fglrx(0): Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900
(**) fglrx(0): Default mode "1152x864": 96.8 MHz (scaled from 0.0 MHz), 63.0 kHz, 70.0 Hz
(II) fglrx(0): Modeline "1152x864" 96.76 1152 1224 1344 1536 864 865 868 900 +hsync
(**) fglrx(0): Default mode "1152x864": 81.6 MHz (scaled from 0.0 MHz), 53.7 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1152x864" 81.62 1152 1216 1336 1520 864 865 868 895 +hsync
(**) fglrx(0): Default mode "1152x864": 64.7 MHz (scaled from 0.0 MHz), 43.0 kHz, 47.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 64.67 1152 1208 1328 1504 864 865 868 915 interlace +hsync
(**) fglrx(0): Default mode "1152x864": 58.3 MHz (scaled from 0.0 MHz), 39.2 kHz, 43.0 Hz (I)
(II) fglrx(0): Modeline "1152x864" 58.28 1152 1200 1320 1488 864 865 868 911 interlace +hsync
(**) fglrx(0): Default mode "1024x480": 38.2 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "1024x480" 38.16 1024 1048 1152 1280 480 481 484 497 +hsync
(**) fglrx(0): Default mode "848x480": 31.5 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "848x480" 31.48 848 864 952 1056 480 481 484 497 +hsync
(**) fglrx(0): Default mode "720x576": 32.7 MHz (scaled from 0.0 MHz), 35.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x576" 32.66 720 744 816 912 576 577 580 597 +hsync
(**) fglrx(0): Default mode "720x480": 26.7 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "720x480" 26.71 720 736 808 896 480 481 484 497 +hsync
(**) fglrx(0): Default mode "640x400": 28.1 MHz (scaled from 0.0 MHz), 33.7 kHz, 75.0 Hz
(II) fglrx(0): Modeline "640x400" 28.07 640 696 736 832 400 413 415 449
(**) fglrx(0): Default mode "640x400": 24.9 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz
(II) fglrx(0): Modeline "640x400" 24.92 640 664 760 792 400 460 462 525
(**) fglrx(0): Default mode "640x350": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 70.0 Hz
(II) fglrx(0): Modeline "640x350" 25.18 640 656 752 800 350 387 389 449 +vsync
(**) fglrx(0): Default mode "512x384": 19.8 MHz (scaled from 0.0 MHz), 29.8 kHz, 60.0 Hz
(II) fglrx(0): Modeline "512x384" 19.81 512 544 624 664 384 451 453 497
(**) fglrx(0): Default mode "400x300": 24.8 MHz (scaled from 0.0 MHz), 46.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 24.75 400 408 448 528 300 601 602 625 doublescan
(**) fglrx(0): Default mode "400x300": 22.3 MHz (scaled from 0.0 MHz), 45.0 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "400x300" 22.33 400 416 480 496 300 601 605 742 doublescan
(**) fglrx(0): Default mode "320x240": 15.8 MHz (scaled from 0.0 MHz), 37.9 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 15.75 320 328 360 416 240 481 482 501 doublescan
(**) fglrx(0): Default mode "320x240": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x240" 12.59 320 328 376 400 240 491 493 525 doublescan
(**) fglrx(0): Default mode "320x200": 13.1 MHz (scaled from 0.0 MHz), 31.5 kHz, 75.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 13.10 320 352 368 416 200 406 407 417 doublescan
(**) fglrx(0): Default mode "320x200": 12.6 MHz (scaled from 0.0 MHz), 31.5 kHz, 60.0 Hz (D)
(II) fglrx(0): Modeline "320x200" 12.59 320 336 384 400 200 457 459 524 doublescan
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.3
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/lib/xorg/modules//libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 1.1
(==) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/xorg/modules//libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 1.1
(==) fglrx(0): HPV inactive
(**) fglrx(0): FSAA enabled: NO
(==) fglrx(0): FSAA Gamma enabled
(==) fglrx(0): FSAA Multisample Position is fix
(==) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Reloading /usr/lib/xorg/modules/linux//libfglrxdrm.so
(II) fglrx(0): Depth moves disabled by default
(==) fglrx(0): Capabilities: 0x00000000
(==) fglrx(0): CapabilitiesEx: 0x00000000
(==) fglrx(0): cpuFlags: 0x4000000f
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(II) fglrx(0): [drm] DRM buffer queue setup: nbufs = 100 bufsize = 65536
(==) fglrx(0): UseFastTLS=0
(==) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(II) LoadModule: "glesx.so" (glesx)
(WW) LoadModule: given non-canonical module name "glesx.so"
(II) Loading /usr/lib/xorg/modules//glesx.so
(II) Module glesx: vendor="X.Org Foundation"
compiled for 7.1.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) Loading extension GLESX
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b]
[1] 0 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b]
[2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
[3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
[4] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
[5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
[6] -1 0 0xfe600000 - 0xfe6000ff (0x100) MX[b]
[7] -1 0 0xfeb00000 - 0xfeb003ff (0x400) MX[b]
[8] -1 0 0x50000000 - 0x50003fff (0x4000) MX[b]
[9] -1 0 0x50004000 - 0x500047ff (0x800) MX[b]
[10] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
[11] -1 0 0xfdc00000 - 0xfdc0ffff (0x10000) MX[b](B)
[12] -1 0 0xa8000000 - 0xafffffff (0x8000000) MX[b](B)
[13] -1 0 0xfdd00000 - 0xfdd1ffff (0x20000) MX[b](B)
[14] -1 0 0xfde00000 - 0xfde0ffff (0x10000) MX[b](B)
[15] -1 0 0xb0000000 - 0xb7ffffff (0x8000000) MX[b](B)
[16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprU)
[17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprU)
[18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprU)
[19] 0 0 0x0000d000 - 0x0000d0ff (0x100) IX[b]
[20] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
[21] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
[22] -1 0 0x00001400 - 0x000014ff (0x100) IX[b]
[23] -1 0 0x00001000 - 0x000010ff (0x100) IX[b]
[24] -1 0 0x0000ef40 - 0x0000ef5f (0x20) IX[b]
[25] -1 0 0x0000ef20 - 0x0000ef3f (0x20) IX[b]
[26] -1 0 0x0000ef00 - 0x0000ef1f (0x20) IX[b]
[27] -1 0 0x0000eec0 - 0x0000eedf (0x20) IX[b]
[28] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[b]
[29] -1 0 0x0000e800 - 0x0000e8ff (0x100) IX[b]
[30] -1 0 0x0000eeb0 - 0x0000eebf (0x10) IX[b]
[31] -1 0 0x0000ef80 - 0x0000ef83 (0x4) IX[b]
[32] -1 0 0x0000ef68 - 0x0000ef6f (0x8) IX[b]
[33] -1 0 0x0000ef84 - 0x0000ef87 (0x4) IX[b]
[34] -1 0 0x0000ef88 - 0x0000ef8f (0x8) IX[b]
[35] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[b]
[36] -1 0 0x0000efe0 - 0x0000efe7 (0x8) IX[b]
[37] -1 0 0x0000ed80 - 0x0000edbf (0x40) IX[b]
[38] -1 0 0x0000d000 - 0x0000d0ff (0x100) IX[b](B)
[39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
[40] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
(II) fglrx(0): driver needs X.org 7.1.x.y with x.y >= 0.0
(II) fglrx(0): detected X.org 7.1.0.0
(II) Loading extension ATIFGLRXDRI
(II) fglrx(0): doing DRIScreenInit
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: Searching for BusID PCI:1:0:0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenByBusid: drmOpenMinor returns 6
drmOpenByBusid: drmGetBusid reports
drmOpenDevice: node name is /dev/dri/card1
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card2
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card3
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card4
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card5
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card6
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card7
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card8
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card9
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card10
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card11
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card12
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card13
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card14
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: open result is -1, (No such device)
drmOpenDevice: Open failed
drmOpenByBusid: drmOpenMinor returns -19
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 6, (OK)
drmGetBusid returned ''
(II) fglrx(0): [drm] DRM interface version 1.0
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:1:0:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0xb4000
(II) fglrx(0): [drm] mapped SAREA 0xb4000 to 0xb7282000
(II) fglrx(0): [drm] framebuffer handle = 0xb5000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.37.6
(II) fglrx(0): Date: May 25 2007
(II) fglrx(0): Desc: ATI FireGL DRM kernel module
(WW) fglrx(0): Kernel Module version does *not* match driver.
(EE) fglrx(0): incompatible kernel module detected - HW accelerated OpenGL will not work
(II) fglrx(0): [drm] removed 1 reserved context for kernel
(II) fglrx(0): [drm] unmapping 8192 bytes of SAREA 0xb4000 at 0xb7282000
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
(II) fglrx(0): FBADPhys: 0xb0000000 FBMappedSize: 0x08000000
(==) fglrx(0): Write-combining range (0xb0000000,0x8000000)
(II) fglrx(0): FBMM initialized for area (0,0)-(1280,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1280,1024) (front color buffer - assumption)
(II) fglrx(0): Largest offscreen area available: 1280 x 7167
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) Loading extension FGLRXEXTENSION
(II) Loading extension ATITVOUT
(**) fglrx(0): DPMS enabled
(II) fglrx(0): GLESX enableFlags = 0
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
32 256x256 slots
16 512x512 slots
(II) fglrx(0): Acceleration enabled
(II) fglrx(0): Direct rendering disabled
(==) fglrx(0): Using hardware cursor
fbarea0->box.x1 0x00000000, fbarea0->box.y1 0x00000404
fbarea0->box.x2 0x00000500, fbarea0->box.y2 0x00000406
icon[0].start=0x505000
fbarea1->box.x1 0x00000000, fbarea1->box.y1 0x00000406
fbarea1->box.x2 0x00000500, fbarea1->box.y2 0x00000408
icon[1].start=0x508000
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension XAccessControlExtension
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(II) Loading local sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/xorg/modules/extensions//libGLcore.so
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 7.2.0, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.3
(II) GLX: Initialized MESA-PROXY GL provider for screen 0
[glesx] __glESXExtensionInit: No GL ES2.0 capable screen found!
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Option "XkbLayout" "gb"
(**) Keyboard0: XkbLayout: "gb"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "ExplorerPS/2"
(**) mx518: Device: "/dev/input/mice"
(**) mx518: Protocol: "ExplorerPS/2"
(**) Option "CorePointer"
(**) mx518: Core Pointer
(**) Option "Device" "/dev/input/mice"
(**) Option "Buttons" "10"
(==) mx518: Emulate3Buttons, Emulate3Timeout: 50
(**) Option "ZAxisMapping" "4 5"
(**) mx518: ZAxisMapping: buttons 4 and 5
(**) Option "ButtonMapping" "1 2 3 6 7"
(**) mx518: Buttons: 14
(**) Option "Resolution" "800"
(**) mx518: Resolution: 800
(II) XINPUT: Adding extended input device "mx518" (type: MOUSE)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) mx518: ps2EnableDataReporting: succeeded
xorg.conf:
Section "ServerLayout"
Identifier "Xorg"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "mx518" "CorePointer"
EndSection
Section "ServerFlags"
Option "AllowMouseOpenFail" "true"
Option "AIGLX" "off" # Disable AIGLX
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
# Fonts
FontPath "/usr/share/fonts/misc:unscaled"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/75dpi"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/100dpi"
FontPath "/usr/share/fonts/cyrillic"
FontPath "/usr/share/fonts/Type1"
FontPath "/usr/share/fonts/TTF"
EndSection
Section "Module"
Load "ddc" # ddc probing of monitor
Load "dbe"
Load "dri"
Load "drm"
Load "extmod"
Load "glx"
Load "bitmap" # bitmap-fonts
Load "type1"
Load "freetype"
Load "record"
Load "fglrx"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "keyboard"
# Options
Option "CoreKeyboard"
Option "XkbRules" "xorg"
Option "XkbModel" "pc105"
Option "XkbLayout" "gb"
# Option "XkbVariant" ""
EndSection
Section "InputDevice"
Identifier "mx518"
Driver "mouse"
# Options
Option "CorePointer"
Option "Resolution" "800"
Option "Device" "/dev/input/mice"
Option "Protocol" "ExplorerPS/2"
Option "ZAxisMapping" "4 5"
Option "Buttons" "10"
Option "ButtonMapping" "1 2 3 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "AG Neovo"
ModelName "F-419"
HorizSync 24.0 - 80.0
VertRefresh 50.0 - 75.0
# Options
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "Card0"
VendorName "All"
BoardName "All"
Driver "fglrx"
# Options
# Option "XAANoOffscreenPixmaps" "true"
# Option "AGPMode" "8"
# Option "ColorTiling" "on"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultColorDepth 24
SubSection "Display"
Depth 1
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 4
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1280x1024" "1280x960" "1024x768" "800x600" "640x480"
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
#Section "Extensions"
# Option "XEVIE" "Enable"
# Option "Composite" "Enable"
#Endsection
Would it be possible to explain the other warnings in Xorg.0.log? Rather curious about those apart from the obvious one, too.
Thanks.
Last edited by Newnux (2007-07-11 16:04:15)Indeed, that seems the end-all error of it all.
I'll summarise my warnings, some for curious reasons:
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory) # What's this?
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found # Not a problem.
(WW) fglrx(0): Only one display is connnected,so single mode is enabled # No problem.
(WW) fglrx(0): Kernel Module version does *not* match driver.
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
Anyway, I wondered about versions and noticed this:
(II) fglrx(0): [drm] DRM interface version 1.0
(II) fglrx(0): [drm] created "fglrx" driver at busid "PCI:1:0:0"
(II) fglrx(0): [drm] added 8192 byte SAREA at 0xbc000
(II) fglrx(0): [drm] mapped SAREA 0xbc000 to 0xb7285000
(II) fglrx(0): [drm] framebuffer handle = 0xbd000
(II) fglrx(0): [drm] added 1 reserved context for kernel
(II) fglrx(0): DRIScreenInit done
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.37.6
(II) fglrx(0): Date: May 25 2007
(II) fglrx(0): Desc: ATI FireGL DRM kernel module
(WW) fglrx(0): Kernel Module version does *not* match driver. # included to show where this was displayed
All versions previous to that show 8.38.6:
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 7.1.0, module version = 8.38.6
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 1.0
So I assume I have an old version dotted around somewhere, but I'm not sure about how it's all loaded and such.
Now, quoting something I'd come across a few times and taking it from thinkwiki:
If you lose hardware acceleration after a driver update this can be caused by an old fglrx kernel module being loaded.
Check out /var/log/Xorg.0.log for a message like:
(WW) fglrx(0): Kernel Module version does *not* match driver.
(EE) fglrx(0): incompatible kernel module detected - HW accelerated OpenGL will not work
You can verify this yourself by looking at the version message some lines above. It should read something not matching the installed version like:
(II) fglrx(0): Kernel Module Version Information:
(II) fglrx(0): Name: fglrx
(II) fglrx(0): Version: 8.10.19
The cause for this trouble might be that there resist multiple versions of the fglrx module within the kernel module search path.
Go to /lib/modules/<your linux kernel version>/ and type # grep fglrx modules.dep.
If grep finds multiple lines you nailed down the problem. All you have to do now is to delete any versions of the module (look at the filedate) but the most current one. Then run # depmod and you are done.
Hint:
Newer versions (8.21.7) of the fglrx module seem to be installed in the extra/ subdirectory.
Older versions (8.19.10) used to be located in the kernel/drivers/char/drm/ subdirectory.
How does this apply to Arch? I only found one instance of fglrx by using that method.
Edit: Forgot to add that I've tried reinstalling a few times, it doesn't really seem to do anything. Wondering if I should attempt to install an older version or something, but I don't get why the driver numbers don't match for me. Surely others have updated their drivers too.
Last edited by Newnux (2007-07-11 13:28:55) -
Error Message - Value Entered Does Not Match Format of Field
I keep getting an error message in Adobe Pro X: "The value entered does not match the format of the field [JF13]".
I have JF13 programmed as follows:
On Calculate tab:
if(Number(this.getField("ck4").value) > 0) this.getField("JF13").value = Number(this.getField("FL019").value); else this.getField("JF13").value = " ";
It is programmed this way so if the user checks the check box before the field, only then will JF13 populate a value, which pulls from FL019. I also have the settings set to "number" because the data needs to display as a dollar amount $xxx.xx.
FL019 is a hidden field on the form which pulls a dollar amount from a Mainframe, and its settings are also set to "Number" :
I get four pop up windows with the above mentioned error message, and the only way to make the message stop is to remove the "number" format from the fields. However, when this is done, if any number which ends in a zero is entered, it cuts off the zero. This is not acceptable either.
Is there some sort of script I could add or some other way to prevent both the error message and the cutting off of the zero on JF13?
I am not very proficient with javascript, so any assistance would be appreciated!Thank you so much for your response!!
Forgive me for my lack of knowledge - but where exactly would I add that in the script?
I tried it like this:
if(Number(this.getField("ck4").value) > 0) this.getField("JF13").value = Number(this.getField("FL019").value); else this.getField("JF13").value = ""(empty string);
And I got an error saying I was missing a parenthesis. Should it go somewhere else or am I completely off? -
Hii ..
need help on this ..
This what I am doing ..
I am using a DATAEXPORT function to export level0 data from my essbase 11.1.2.2 to Microsoft SQL 2008 tables.
So what I did first I exported the level0 data to a flat file using DATAEXPORT and the created the SQL columns by the same in that order only in my SQL table.
When I run it fails with this error:
ODBC Layer Error: [21S01] ==> [[DataDirect][ODBC SQL Server Wire Protocol driver][Microsoft SQL Server]Column name or number of supplied values does not match table definition.]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021014)
ODBC Layer Error: Native Error code [213]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Error(1012085)
Unable to export data to SQL table [dataexp]. Check the Essbase server log and the system console to determine the cause of the problem.
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021002)
SQL Connection is Freed
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Warning(1080014)
Transaction [ 0x1c50001( 0x51ee7d66.0x80342 ) ] aborted due to status [1012085].
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1012579)
Total Calc Elapsed Time for [test.csc] : [1.44] seconds
=============================================================
I did a simple test on my Sample.basic application then ..
loaded the calc data to it and then used the below script to export to a flat file
//ESS_LOCALE English_UnitedStates.Latin1@Binary
SET DATAEXPORTOPTIONS
DataExportLevel "Level0";
DataExportOverwriteFile ON;
DataExportColFormat OFF;
DataExportDimHeader OFF;
FIX(
"Jan",
"Sales",
"Actual"
/*DATAEXPORT "File" "," "/home/hypadmin/samtest.txt";*/
DATAEXPORT "DSN" "Abhitest" "sample" "sa" "welcome1";
ENDFIX
out put as below:
"Sales"
"100-30","California"
"Jan","Actual",145
Now In sql I created only 3 columns with name Jan/Sales/Actual and when I run this script again with comments removed .. I get the same error as what I have got in my first test case with other application ..
but when I create the columns with same name as what its in export
Sales/100-30/Califirnia/Jan/Actual
It created the new rows successfully ..
So with this I think the error which I am getting with my other application might be because of the same column issue .. but then I have created all the columns by looking at the export file only as I did in sample ..
Any idea would be helpful ..
Thanks
Abhishek
IFirst make sure you add
DataExportRelationalFile ON;
to your set commands it is missing
I alwats like to also add
DataExportColHeader dimensionName;
so I am sure what dimension is getting put into the columns.
Then count the number of dimensions in your outline (exclude attribute dimensions). You need at least that many columns in your table -1 + the number of members you will be returning as columns in the export
Taking your example Sample basic has 5 dimensions
Measures
Years
Scenario
Product
Market
Since you did not specify a dataexportcolheader it took the dense dimension Scenario as the columns. Your fix statement is limiting that to one member. Doing the math
5 -1 + 1 = 5 columns in your table which is what you found works. Suppose you fixed on bothe Actual and budget in scenario then you would need 6 columns 5 -1 +2 -
The content type of the response message does not match the content type of the binding
I have written an ASP.Net web service which returns english,chinese and portuguese data. Everything seemed working fine until the method retunred only english data. The moment it returns english, chinese and portuguese data I get the error:
The content type text/html; charset=utf-8 of the response message does not match the content type of the binding (text/xml; charset=utf-8). If using
a custom encoder, be sure that the IsContentTypeSupported method is implemented properly. The first 1024 bytes of the response were:
'<!DOCTYPE html> <html> <head> <title>Runtime Error</title>
<meta name="viewport" content="width=device-width" /> <style> body {font-family:"Verdana";font-weight:normal;font-size:
.7em;color:black;} p {font-family:"Verdana";font-weight:normal;color:black;margin- -5px} b {font-family:"Verdana";font-weight:bold;color:black;margin-
H1 { font-family:"Verdana";font-weight:normal;font-size:18pt;color:red } H2 { font-family:"Verdana";font-weight:normal;font-size:14pt;color:maroon
} pre {font-family:"Consolas","Lucida Console",Monospace;font-size:11pt;margin:0;padding:0.5em;line-height:14pt} .marker {font-weight:
bold; color: black;text-decoration: none;} .version {color: gray;} .error {margin-bottom: 10px;} .expandable
{ text-decoration:underline; font-weight:bold; color:navy; cursor:hand; } @media screen and (max-width: 639px) { pre { width: 440px; o'.
It is not written using WCF ... any workarounds?!
Thank you.Hi Raj Krish,
For ASP.NET related issue, please post to the following forum:
http://forums.asp.net/
Regards,
Barry
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Data type of the base attribute or the base value does not match...
...the assigned expression.
Hello all,
I always get the Error
+<ERROR+
TEXT="'DWH.CUB_REGISTRATIONS_AW.REGISTRATIONS': XOQ-02517: Der Datentyp des Basisattributs oder der Basisgröße stimmt nicht mit dem zugeordneten Ausdruck überein.
XOQ-01400: Ungültige Metadatenobjekte"/>
The English message must be something like this:
The data type of the base attribute or the base value does not match the assigned expression.
when I run my mapping. The attribute REGISTRATIONS is NUMERIC (12,2) in the Cube and I map a NUMERIC(12,2) constant in it.
I use a simple OWB-Mapping for loading, but I don't understand why it doesn't function. Other mappings where the attributes are out of a
table I put in a cube are running well.
I tried different things, but nothing fixed my problem. Any idea ?
Thanks a lot for help
MichaelTechnically this is a 'warning' from the server, not an 'error'. This means that the change you made should have been submitted, but you get an warning message on the client. AWM would suppress this warning, but evidently OWB does not. Can you switch to use AWM?
Here is the definition of the warning along with 'cause' and 'action' sections. (Unfortunately these sections are not translated into German for some reason.)
>
02517, 0, "The data type \"%(1)s\" of the base attribute or base measure is different from the mapped expression \"%(2)s\"."
// *Cause: Either the base attribute or base measure with the mapped expression was set to an inconsistent data type, or it was mapped to an expression of a different data type from its fixed data type.
// *Action: When changing a mapped expression for a base attribute or base measure, ensure that the expression has the same data type; otherwise, set the data type of the base attribute or base measure to NULL first. When a base attribute or a base measure has an existing mapped expression, do not set it to a different data type.
>
It is probably safe to ignore this warning, but if you can post the relevant XML for the cube, then will probably be able to spot the problem. I assume that REGISTRATIONS is a measure in the cube CUB_REGISTRATIONS_AW, so this is what you can look for in the XML:
(1) The definition of the base measure along with the datatype. It should be something like this
<Measure>
<BaseMeasure
SQLDataType="NUMBER(12,2)"
ETMeasureColumnName="REGISTRATIONS"
Name="REGISTRATIONS">(2) The mapping info for the measure, which should looks something like this:
<MeasureMap
Name="REGISTRATIONS"
Expression="...">
<Measure Name="REGISTRATIONS"/>
</MeasureMap>I don't know if you can get the XML directly from OWB. If not, then DBMS_CUBE.EXPORT_XML should work (assuming you are in 11.2). You could also attach AWM and save the cube to an XML template. -
Hi ,
We have enabled context sensitive DFF in Bank Branch Page for HZ_PARTIES DFF , We have created Flex Map so that only bank branch context fields are only displayed in the bank branch page and as we know party information DFF is shared by supplier and Customer Page so we dint want to see any Bank Branch fields or context information in those pages.
We have achieved the requirement but when open existing branches bank branch update is throwing below error message :
"The value in flexfield context reference web bean does not match with the value in the context of the Descriptive flexfield web bean BranchDescFlex. If this in not intended, please go back to correct the data or contact your Systems Administrator for assistance."
this error is thrown only when we open existing branches, if we save existing branch and open then it is not throwing any error message.
Please let us know reason behind this error message.
Thanks,
MrudualaYou are kidding? It took me about 3 minutes to scroll down on my tab to get to the triplex button!
Habe you read the error message?
Quote:
java.sql.SQLSyntaxErrorException: ORA-04098: trigger 'PMS.PROJECT_SEQ' is invalid and failed re-validation
Check the trigger and it should work again.
Timo -
UPGRADED 10.4.11 ON MACBOOK PRO INTEL TO 10.5.1 (FAMILY PACK VERSION), UPDATES TO 10.5.8 WILL NOT SAVE DUE TO, "DIGITAL SIGNATURE DOES NOT MATCH". ANY IDEAS? CAN I UPGRADE TO 10.6.1 WITHOUT SAME ISSUE.
Well, not sure if having the disk in a firewire case or over a network would have made a difference.
The solution of making a disk image as in article http://support.apple.com/kb/TS2664 was what worked for me.
After, mounting the disk image the Migration Assistant completed without errors. So far everything seems to be working like it did on 10.4.11. -
Good day Guys
First of all I am not an Exchange Expert, and I might be asking a very stupid question, but please bare with me. :)
While I was on leave our Mail server fell over and The company got a Specialist to help out for the time being.
We where\are on Microsoft Exchange 2007 , which Fell over, and the specialist was able to recover as much data as he could.
They then installed Exchange 2013 and tried to migrate everything from 2007 to 2013 and not everything migrated over.
But the problem is, Outlook Anywhere was enable on 2007 and worked a 100% (before the disaster)
With Exchange 2013 I get the following error message when trying to connect With Outlook 2013, using an external connection:
"There is a problem with the proxy server's security certificate. The name on the security certificate is invalid or does not match the name of the target site "Mailserver"
Outlook is unable to connect to the Proxy server. (Error Code 0)"
Has anyone had the Similar when migrating over from 2007 to 2013 or is this an Issue on IIS and nothing to do with Exchange migration?
Your assistance will be greatly appreciated.Hi,
Firstly, I would suggest we use Exchange 2013 FE as the Outlook Anywhere proxy server.
For the certificate issue, it mostly occurs because the host name that Outlook are trying to access does not match the certificate SAN. Please check with this point. If they do not match, you
can change the host name by referring to the following article:
https://support.microsoft.com/kb/940726/en-us?wa=wsignin1.0
Thanks,
Simon Wu
TechNet Community Support -
Datetime value does not match the specified format
Hi All,
I am writing this function for a template
case when "Employment Events (Current)"."Most Recent Hire Date" is NULL then NULL else CAST(TIMESTAMPDIFF(SQL_TSI_YEAR,cast(cast("Employment Events (Current)"."Most Recent Hire Date" as char)as timestamp),Cast(Cast(@{EndDate}{CAST('2011-01-01' AS DATE)} AS CHAR) AS TIMESTAMP)) AS CHAR)||' year(s) ' end
but when it runs, it throws me this error
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 43119] Query Failed: [nQSError: 46046] Datetime value 2011-01-01 does not match the specified format. (HY000)
What am I doing wrong? "Employment Events (Current)"."Most Recent Hire Date" is set to max - aggregation in the rpd.I found the solution as well.
The ODBC driver on the Windows server was old (Version 6). I upgraded that to SQL Server Native Client 11.0 and everything works fine.
Maybe you are looking for
-
Selection screen of logical database PCH
Hi all, I am writing a report using the logical database PCH. For this report I need the full selection screen of the logical database, especially the structure parameters. However, wenn I test my program, I only get a reduced selection screen withou
-
Replication of material from MM to SRM with only pricing info
Hi, We want to replicate only those materials from MM to SRM for which prices are maintained in the MM system.Pls let me know how to get this done. Thanks, Manu
-
Wrapping text at Web Analysis Item
Hello, Does anybody have a clue how we can wrap the text at the columns of web Analysis Item at WEB application Designer 7.x At the previous version 3.x it was something done with table interface class. Although SAP clames that all this fancionality
-
I would like to ask how to create ASP documents
Dreamweaver CC without the ASP option, I would like to ask how to create ASP documents Thanks
-
-24988 DBM -4008,Unknown user name/password combination
Hello, I am not able to connect Whit database Manager Gui 7.6 with the standard user and password, (control,control e.g). The Database Manager Client show the follow error: -24988 DBM -4008,Unknown user name/password combination but from the dbhost w