Max number of agents per proxy

Is there a suggested maximum number of agents per proxy, especially a proxy co-located with the enterprise controller?
Thanks,
Tim Reidy

This would depend on usage patterns and what type of hardware the proxy controller is running.
According to some whitepapers I have you're looking at :
For only hardware management - 5000 systems per enterprise controller, 1000 systems per proxy controller
For hardware, OS, update and virtualization - 3000 systems per enterprise controller, 1000 systems per proxy controller
hardware specs are:
Sparc T3's, 16-core T3 processor, 32 GB RAM for the EC, 16 GB RAM for ProxyController
Intel, Sun Fire x4270's, 2 x Quad-core Nehalem processors, 36 GB RAM for EC, 8 GB RAM for ProxyController

Similar Messages

Max. number of WLCs per WCS

Hi,
I know this is a fairly basic question but I can't find answer in WCS Q&A's etc.
I'm looking at a deployment where there will be many small sites with only 5 or 6 APs and a 2106 WLC. Each site will be in a different mobility group.
I know WCS licensing counts APs, but is there a max. number of WLCs?
Thanks, MH

Hi Mark,
The supported number of WLC's per WCS is based on the WCS Platform used :)
Minimum server requirements
Cisco WCS High-End Server
â¢ 3000 lightweight access points, 1250 standalone access points, 750 wireless LAN controllers
â¢ Two IntelÂ® Xeon Dual Core CPU's; 3.0 GHz, 8 GB RAM, 200 GB HDD
Cisco WCS Standard Server
â¢ 2000 lightweight access points, 1000 standalone access points, 150 wireless LAN controllers
â¢ IntelÂ® Dual Core CPU; 3.2 GHz, 4 GB RAM, 80 GB HDD
Cisco WCS Low-End Server
â¢ 500 lightweight access points, 200 standalone access points, 50 wireless LAN controllers
â¢ IntelÂ® CPU; 3.06 GHz, 2 GB RAM, 30 GB HDD
CiscoWorks WLSE Models 1130-19 or 1133 running Cisco WCS
â¢ 1500 lightweight access points, 100 wireless LAN controllers
â¢ Intel Pentium 4 CPU; 3 GHz, 3 GB RAM, 38 GB HDD
http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd802570d0.html
Hope this helps!
Rob

Max number of VMs per free ESXi hypervisor?

VMware Community,
I've just installed the free ESXi 5.5 hypervisor and I'm wondering if the same virtual machine limits apply to the standalone scenario as vCenter? Can I actually run 512 VMs? What, if any, is the max number of VMs I can run on a free version of ESXi?

As of ESXi 5.5 most limitations were removed and only an 8 vCPU limit per virtual machine remains. So unless I'm mistaken, the mentioned 512 VM per host (see http://www.vmware.com/pdf/vsphere5/r55/vsphere-55-configuration-maximums.pdf) apply to the free Hypervisor too.
André

Throttling a file adapter to consume a max number of files per minute

Is there a way to design a file adapter to throttle its processing bandwidth.
A simple use case scenario is describes as follows;
A File Adapter can only consumes a max of 5 files per minute. The producer average throughput is 3 files per minute but during peak times it can send 100 files per min. The peak times occur during end of year or quarterly accounting periods. If the consumer consumes more than 5 files per min the integrity of the environment and data is compromised.
The SLA for the adapter is to :
- Each file will be processed within 2 seconds.
- Maximum File Transactions Per minute is 5
An example is as follows.
The producer sends 20 files to its staging directory within a minute. The consumer only processes 5 of these files in the first minute, sleeps then wakes up to consume the next 5 files in the second minute. This process is repeated until all files are processed.
The producer can send another batch of files when ever it likes. So in the second minute the producer can send another 70 files. The consumer will throttle the files so it only processes 5 of these files every minute.

Hi,
If you have a polling frequency set to 2 secs..then controlling it to read only five files a min is difficult.?You can have the polling frequecy changed to 12secs
or u can schedule a BPEL for every min and use synchronous read operation and loop it 5 times to read 5 files.

Max Number of threads per Process in Solaris 8

I'm running into qpplication which crashes with a segfault when the LWP for that process hits about 255, i'm trying to find the maximum number of threads per process using sysconf and its returning -1
#include <unistd.h>
int
main(void)
printf("%ld\n",sysconf(_SC_THREAD_THREADS_MAX));
return 0;
I'm using gcc 3.3.2
If anyone can tell me the maximum number of threads per process I would really appreicate it.
Also the maximum number of open files per process.
Thanks in advance
- Rodrick Brown
- DoITT

Please make sure that you build a
multithreaded program first (check with ldd).
If anyone can tell me the maximum number of threads per process I would
really appreicate it.
Also the maximum number of open files per process. It depends on the architecture (x86/SPARC), OS version,
64 or 32-bit, /etc/system, shell limitations (/usr/bin/ulimit) ...
Search for "rlim_fd_max / rlim_fd_cur" on docs.sun.com too.
HTH,
-vladimir

Trickles connection; max number of clinet per server; more services

Dear,
I found on web something about Trickles connection. Is there some further reading about Trickles connection in Java? Is that just logical concept or it is language-oriented implementation? If it is only logical concept, I suppose it is equal to TCP connection on client side and UDP connection on server side, of course if that is possibly? Can anyone tell me something more about that? Thank you.
If I am using stateful connection between server and client, what is average number of client which server can serve - you can specify some PC configuration and give number which depends on that PC? Thank you.
If somewhere are more services which should communicate, but they are on a same PC (suppose all are written in Java). What is the best way of communication between themselves?
If you can, recommend me some very good book which can give me at least one answer on my questions. It is better, if book is available as e-book.

It's not supported in Java so you're asking in the wrong place.

Max number of instances per Server

Good morning,
I've installed Oracle9i in a Windows 2000 Server with 1GB of memory. After that I've created several instances of Oracle DB. With 3 instances my server works acceptably, but after adding two mor instances I've begun to have some perfomance problems and the access speed has considerably decreased, so my question is, what is the maximum number of instances that the same Oracle server can support in order to optimize the access to the DB?
Thanks in advance.
Isabel

Hi,
I am confronted with a similar problem. ie, we have got several instances on the basis of one application/one instance. I am asked to regroup all these instances to one and only one instance containing several schemas to reduce the number of servers, number of instances and on the way reduce the administrative ( dba ) tasks. As i have got some knowledge of dba, I thought of installing this instance under Oracle 10g like this : an application on its own tablespace and the backup of this tbs via rman. So when an application crashes, I can make use of TSPITR to bring the database to its initial ( stable ) status. My questions are :
1° any re-initialisation of the database will sanction all the schemas. Is there any
way to avoid this ?
2° as different tablespaces be brought to a consistency status different in time via
TSPITR even if the controlfile happens to be the same ?
3° if I opt for UNDO management AUTO, there can be only one UNDO TBS
active at a time. As this won't render me to trouble when i need to recover
only one application ? or on performance ?
Any prompt reply will be greatly appreciated.
Best regards.
Tiroumalai

Max number of devices per app

I work for a school and we have 200 ipads. Can I purchase one app and place it on all 200. I am assuming not, but are there restrictions?

Repost your question in the iPad in the Enterprise (Schools/Business) forum https://discussions.apple.com/community/ipad/ipad_in_the_enterprise Maybe someone from another school system will answer. Here's one link, but I'm not sure it applies to schools. http://www.idownloadblog.com/2011/08/10/apple-id-limited-10-devices/
 Cheers, Tom

Is there a max number of Apple pro prints allowed per order? I tried 300, then 65 and neither worked. At $2.99 per for shipping, it is expensive to order 20 sets when I used to do just one for all.

Is there a max. number of Apple pro prints allowed per order with the updated iPhoto/Mountain Lion?
I have been using the system for years and have had no issues, but this first try under Mountain Lion I was told the max was 300 prints per order.
It order did not go through, nor did one with 65 photos. When I tried 2, it was fine, but at $2.99 shipping, plus tax,
paying $60 to get all 300 of my photos shipped is unreasonable.
Is this a glitch in the new OS? Hopefully it will be fixed.

Hi blabla12345,
(untested and without warranty)
replace this line:
const sSaveCUBE = "CUBE";
with this:
const sSaveCUBE = "cube";
Have fun

REPORT BUILDER: MAX. NUMBER OF RECORDS PER PAGE

Dear Consultant,
Using DEVELOPER 2000 R2.1 REPORT BUILDER, is there any way to set the " MAXIMUM NUMBER OF RECORDS PER PAGE" dynamically by user input when calling the report, without the need to modify the report at Design time and recompile it?
Thanks for your help.
Ghia Haidar
Developer
Astrolabe IT - Professional Consultants
Beirut, Lebanon
Phone: + 961 1 841.050
Fax: + 961 1 841.055 www.astrolabe.com.lb
null

Refer Manish question.
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Ali DHAINI ([email protected]):
Dear Consultant,
Using DEVELOPER 2000 R2.1 REPORT BUILDER, is there any way to set the " MAXIMUM NUMBER OF RECORDS PER PAGE" dynamically by user input when calling the report, without the need to modify the report at Design time and recompile it?
Thanks for your help.
Ghia Haidar
Developer
Astrolabe IT - Professional Consultants
Beirut, Lebanon
Phone: + 961 1 841.050
Fax: + 961 1 841.055 www.astrolabe.com.lb
<HR></BLOCKQUOTE>
null

Max number of chars in process message MSEL?

Hi, what is the max number of characteristics can be used in process message category's MSEL table? Right now, I am using more than 99 characteristics and I get a short dump DYNPRO_FIELD_CONVERSION. Is it really limited to 99 characteristics and if it is true, is there an OSS note to change it to allow more than 99?
Thanks and points available

Please make sure that you build a
multithreaded program first (check with ldd).
If anyone can tell me the maximum number of threads per process I would
really appreicate it.
Also the maximum number of open files per process. It depends on the architecture (x86/SPARC), OS version,
64 or 32-bit, /etc/system, shell limitations (/usr/bin/ulimit) ...
Search for "rlim_fd_max / rlim_fd_cur" on docs.sun.com too.
HTH,
-vladimir

Max number of records in MDM workflow

Hi All
Need urgent recommendations.
We have a scenario where we need to launch a workflow upon import of records. The challenge is source file contains 80k records and its always a FULL load( on daily basis) in MDM. Do we have any limitation in MDM workflow for the max number of records? Will there be significant performance issues if we have a workflow with such huge number of records in MDM?
Please share your inputs.
Thanks-Ravi

Hi Ravi,
Yes it can cause performance overhead and you will also have to optimise MDIS parametrs for this.
Regarding WF i think normally it is 100 records per WF.I think you can set a particular threshold for records after which the WF will autolaunch.
It is difficult to say what optimum number of records should be fed in Max Records per WF so I would suggest having a test run of including 100/1000 records per WF.Import Manager guide say there are several performance implications of importing records in a WF,so it is better to try for different ranges.
Thanks,
Ravi

Max number of rows in a BEX structure

Hi gurus,
we need to create a structure with 164 key figures, and before starting doing it, does anybody knows which is the max number of rows that can be created on a BEX structure?
I'm not asking about max number of rows on a query, i'm asking about the number of entries that you can manually create on a structure. Is there a maximum?
Thanks in advance,
regards,
Miguel

Hi Migual,
You can add as per your requirement. Please refer the following link
http://help.sap.com/saphelp_nw04/helpdata/en/4d/e2bebb41da1d42917100471b364efa/content.htm
Assign Points if helpful.
Regards,
Amit

Max number of rows?

Hi,
We have a new implementation of Enterprise X1 3.1 and are trying to determine what determines the maximum number of rows that can successfully be generated using Webi. Is there a hard limit that Webi has (assuming the Universe max rows is deactivated)?
Also, is there a limit for Live Office extractions into Excel? What are the main drivers for this limit?
Finally, all other factors being equal, are there different limits for the number of rows a query can return successfully in Webi vs Deski vs BEx? How does the performance of these three tools compare to each other in terms of speed?
Thanks!
Darryl

Thanks for your reply! I also got a response back from SAP / BObj that I'll share:
Q) We have a new implementation of Enterprise X1 3.1 and are trying to determine what determines the maximum number of rows that can successfully be generated using Webi. Is there a hard limit that Webi has (assuming the Universe max rows are deactivated)?
=> There is a limit to the number of pages Web Intelligence reports can have. This is because there are a maximum number of pages (per report) the server can process. This number depends on the paper size chosen. Generally, it is approximately 590000 inches vertically by 590000 inches horizontally. Therefore, if you choose a smaller paper size, you get more pages but may not see all the pages of the report.
Resolution:
To work around this behavior, you can either make each line smaller to get more records, or split your report into more than one report to see all your data.
Q) Is there a limit for Live Office extractions into Excel? What are the main drivers for this limit?
=> By default its set to 512 rows and columns....however you can change this by modifying the Liveoffice_config.properties file...you can locate this file in /dswsbobje/lib/dsws_liveoffice_provider.jar.
Q) Are there different limits for the number of rows a query can return successfully in Webi vs. Deski?
=> Although there is no official limit on the number of rows that can be handled by DeskI, it is really not meant to be used like a database, i.e. for returning millions of rows. The purpose of BusinessObjects reporting tools is to get useful information, which is not possible with millions of rows.
=> It has been observed that when the number of rows increases beyond 1.5 million approximately, it starts affecting the Desktop Intelligence performance. This behavior may vary from machine to machine depending upon the available resources and programs (processes) running in the background.
=> The limit is related to the number of rows those can actually be displayed in the report and not how many can be loaded into the data cube. All the rows get loaded in the cube however when it comes to rendering them in the report the problem may arise.
Example: Report A returns 2 million rows into the cube however due to the report design there are only 200 rows in the actual report page and can be run successfully. Report B tries to render all 2 million rows into the actual report page and can fail.
Workaround:
Use filters in the report so that it will retrieve less number of rows and will also help to display useful data.

How to limit number of logins per day?

We have a custom web application (WebAS 6.20) used by people and automated systems. Each user has his own login, and some of these automated systems sometimes produce heavy load because they log into system too often.
Is there an easy way to:
1) limit number of logins to, say, 1000 per day and when this limit is reached - do not allow this user to login till midnight
OR
2) dedicate one of the processes to the specific user
thanks in advance

extend PlainDocument class to restrict the number of characters per line.
Set this class as model to TextArea.
Below is a class which does this. May be its useful
import javax.swing.*;
import javax.swing.text.*;
import java.awt.*;
public class FixedNumericDocument extends PlainDocument {
private int maxLength = 9999;
private String max="";
public FixedNumericDocument(int maxLength) {
super();
this.maxLength = maxLength;
//this is where we'll control all input to our document.
//If the text that is being entered passes our criteria, then we'll just call
//super.insertString(...)
public void insertString(int offset, String str, AttributeSet attr)
throws BadLocationException {
if (getLength() + str.length() > maxLength) {
return;
else {
try {
//check if str is numeric only
int value = Integer.parseInt(str);
//if we get here then str contains only numbers
//chk if it is less than 65535 so that it can be inserted
super.insertString(offset, str, attr);
catch(NumberFormatException exp) {
return;
return;

Max number of agents per proxy

Similar Messages

Maybe you are looking for