Max number of VMs per free ESXi hypervisor?
VMware Community,
I've just installed the free ESXi 5.5 hypervisor and I'm wondering if the same virtual machine limits apply to the standalone scenario as vCenter? Can I actually run 512 VMs? What, if any, is the max number of VMs I can run on a free version of ESXi?
As of ESXi 5.5 most limitations were removed and only an 8 vCPU limit per virtual machine remains. So unless I'm mistaken, the mentioned 512 VM per host (see http://www.vmware.com/pdf/vsphere5/r55/vsphere-55-configuration-maximums.pdf) apply to the free Hypervisor too.
André
Similar Messages
-
Max. number of WLCs per WCS
Hi,
I know this is a fairly basic question but I can't find answer in WCS Q&A's etc.
I'm looking at a deployment where there will be many small sites with only 5 or 6 APs and a 2106 WLC. Each site will be in a different mobility group.
I know WCS licensing counts APs, but is there a max. number of WLCs?
Thanks, MHHi Mark,
The supported number of WLC's per WCS is based on the WCS Platform used :)
Minimum server requirements
Cisco WCS High-End Server
⢠3000 lightweight access points, 1250 standalone access points, 750 wireless LAN controllers
⢠Two Intel® Xeon Dual Core CPU's; 3.0 GHz, 8 GB RAM, 200 GB HDD
Cisco WCS Standard Server
⢠2000 lightweight access points, 1000 standalone access points, 150 wireless LAN controllers
⢠Intel® Dual Core CPU; 3.2 GHz, 4 GB RAM, 80 GB HDD
Cisco WCS Low-End Server
⢠500 lightweight access points, 200 standalone access points, 50 wireless LAN controllers
⢠Intel® CPU; 3.06 GHz, 2 GB RAM, 30 GB HDD
CiscoWorks WLSE Models 1130-19 or 1133 running Cisco WCS
⢠1500 lightweight access points, 100 wireless LAN controllers
⢠Intel Pentium 4 CPU; 3 GHz, 3 GB RAM, 38 GB HDD
http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd802570d0.html
Hope this helps!
Rob -
Throttling a file adapter to consume a max number of files per minute
Is there a way to design a file adapter to throttle its processing bandwidth.
A simple use case scenario is describes as follows;
A File Adapter can only consumes a max of 5 files per minute. The producer average throughput is 3 files per minute but during peak times it can send 100 files per min. The peak times occur during end of year or quarterly accounting periods. If the consumer consumes more than 5 files per min the integrity of the environment and data is compromised.
The SLA for the adapter is to :
- Each file will be processed within 2 seconds.
- Maximum File Transactions Per minute is 5
An example is as follows.
The producer sends 20 files to its staging directory within a minute. The consumer only processes 5 of these files in the first minute, sleeps then wakes up to consume the next 5 files in the second minute. This process is repeated until all files are processed.
The producer can send another batch of files when ever it likes. So in the second minute the producer can send another 70 files. The consumer will throttle the files so it only processes 5 of these files every minute.Hi,
If you have a polling frequency set to 2 secs..then controlling it to read only five files a min is difficult.?You can have the polling frequecy changed to 12secs
or u can schedule a BPEL for every min and use synchronous read operation and loop it 5 times to read 5 files. -
Max Number of threads per Process in Solaris 8
I'm running into qpplication which crashes with a segfault when the LWP for that process hits about 255, i'm trying to find the maximum number of threads per process using sysconf and its returning -1
#include <unistd.h>
int
main(void)
printf("%ld\n",sysconf(_SC_THREAD_THREADS_MAX));
return 0;
I'm using gcc 3.3.2
If anyone can tell me the maximum number of threads per process I would really appreicate it.
Also the maximum number of open files per process.
Thanks in advance
- Rodrick Brown
- DoITTPlease make sure that you build a
multithreaded program first (check with ldd).
If anyone can tell me the maximum number of threads per process I would
really appreicate it.
Also the maximum number of open files per process. It depends on the architecture (x86/SPARC), OS version,
64 or 32-bit, /etc/system, shell limitations (/usr/bin/ulimit) ...
Search for "rlim_fd_max / rlim_fd_cur" on docs.sun.com too.
HTH,
-vladimir -
Max number of agents per proxy
Is there a suggested maximum number of agents per proxy, especially a proxy co-located with the enterprise controller?
Thanks,
Tim ReidyThis would depend on usage patterns and what type of hardware the proxy controller is running.
According to some whitepapers I have you're looking at :
For only hardware management - 5000 systems per enterprise controller, 1000 systems per proxy controller
For hardware, OS, update and virtualization - 3000 systems per enterprise controller, 1000 systems per proxy controller
hardware specs are:
Sparc T3's, 16-core T3 processor, 32 GB RAM for the EC, 16 GB RAM for ProxyController
Intel, Sun Fire x4270's, 2 x Quad-core Nehalem processors, 36 GB RAM for EC, 8 GB RAM for ProxyController -
Trickles connection; max number of clinet per server; more services
Dear,
I found on web something about Trickles connection. Is there some further reading about Trickles connection in Java? Is that just logical concept or it is language-oriented implementation? If it is only logical concept, I suppose it is equal to TCP connection on client side and UDP connection on server side, of course if that is possibly? Can anyone tell me something more about that? Thank you.
If I am using stateful connection between server and client, what is average number of client which server can serve - you can specify some PC configuration and give number which depends on that PC? Thank you.
If somewhere are more services which should communicate, but they are on a same PC (suppose all are written in Java). What is the best way of communication between themselves?
If you can, recommend me some very good book which can give me at least one answer on my questions. It is better, if book is available as e-book.It's not supported in Java so you're asking in the wrong place.
-
Max number of instances per Server
Good morning,
I've installed Oracle9i in a Windows 2000 Server with 1GB of memory. After that I've created several instances of Oracle DB. With 3 instances my server works acceptably, but after adding two mor instances I've begun to have some perfomance problems and the access speed has considerably decreased, so my question is, what is the maximum number of instances that the same Oracle server can support in order to optimize the access to the DB?
Thanks in advance.
IsabelHi,
I am confronted with a similar problem. ie, we have got several instances on the basis of one application/one instance. I am asked to regroup all these instances to one and only one instance containing several schemas to reduce the number of servers, number of instances and on the way reduce the administrative ( dba ) tasks. As i have got some knowledge of dba, I thought of installing this instance under Oracle 10g like this : an application on its own tablespace and the backup of this tbs via rman. So when an application crashes, I can make use of TSPITR to bring the database to its initial ( stable ) status. My questions are :
1° any re-initialisation of the database will sanction all the schemas. Is there any
way to avoid this ?
2° as different tablespaces be brought to a consistency status different in time via
TSPITR even if the controlfile happens to be the same ?
3° if I opt for UNDO management AUTO, there can be only one UNDO TBS
active at a time. As this won't render me to trouble when i need to recover
only one application ? or on performance ?
Any prompt reply will be greatly appreciated.
Best regards.
Tiroumalai -
I work for a school and we have 200 ipads. Can I purchase one app and place it on all 200. I am assuming not, but are there restrictions?
Repost your question in the iPad in the Enterprise (Schools/Business) forum https://discussions.apple.com/community/ipad/ipad_in_the_enterprise Maybe someone from another school system will answer. Here's one link, but I'm not sure it applies to schools. http://www.idownloadblog.com/2011/08/10/apple-id-limited-10-devices/
Cheers, Tom -
DpVmCheck: max number of priv VMs exceeded (1 0, timeout)
Hello,
In our CRM system EHP1 FOR CRM 7 ABAP ,users get this screen mainly for big contracts at different stages like collision run,saving.
Status before error started
I have already gone through notes 1757252
But the parameter rdisp/max_vm_priv_time and rdisp/max_vm_priv_no doesn't exist in our system. Instead is there any other parameter which we can use in our release ?
I could find these errors when the timeout screen occurred :
DEV_DISP
Wed Jul 23 15:26:08 2014
DpVmCheck: max number of priv VMs exceeded (1 > 0, timeout), reset T59/M0/U13880/V4
Wed Jul 23 15:26:28 2014
DpVmCheck: max number of priv VMs exceeded (1 > 0, timeout), reset T59/M0/U13880/V4
Wed Jul 23 15:26:46 2014
*** ERROR => DpRqCheck: T59 in state TM_SLOT_FREE [dpxxdisp.c 8006]
***LOG Q0G=> DpRqBadHandle, bad_req ( DIA) [dpxxdisp.c 6125]
*** ERROR => DpRqBadHandle: BAD REQUEST - Reason: DpRqCheck failed (line 7037): [dpxxdisp.c 6127]
-IN-- sender_id DISPATCHER tid 59 wp_ca_blk -1 wp_id -1
-IN-- action SEND_TO_WP uid 13880 appc_ca_blk -1 type DIA
-IN-- new_stat NO_CHANGE mode 0 len 0 rq_id 24366
-IN-- req_info DP_CANCEL_PRIV
-IN-- msg_name -
*** ERROR => DpRqCheck: T59 in state TM_SLOT_FREE [dpxxdisp.c 8006]
***LOG Q0G=> DpRqBadHandle, bad_req ( DIA) [dpxxdisp.c 6125]
*** ERROR => DpRqBadHandle: BAD REQUEST - Reason: DpRqCheck failed (line 7037): [dpxxdisp.c 6127]
-IN-- sender_id DISPATCHER tid 59 wp_ca_blk -1 wp_id -1
-IN-- action SEND_TO_WP uid 13880 appc_ca_blk -1 type DIA
-IN-- new_stat NO_CHANGE mode 0 len 0 rq_id 24502
-IN-- req_info DP_CANCEL_PRIV
-IN-- msg_name -
*** ERROR => DpRqCheck: T59 in state TM_SLOT_FREE [dpxxdisp.c 8006]
***LOG Q0G=> DpRqBadHandle, bad_req ( DIA) [dpxxdisp.c 6125]
*** ERROR => DpRqBadHandle: BAD REQUEST - Reason: DpRqCheck failed (line 7037): [dpxxdisp.c 6127]
-IN-- sender_id DISPATCHER tid 59 wp_ca_blk -1 wp_id -1
-IN-- action SEND_TO_WP uid 13880 appc_ca_blk -1 type DIA
-IN-- new_stat NO_CHANGE mode 0 len 0 rq_id 24691
-IN-- req_info DP_CANCEL_PRIV
-IN-- msg_name -
sm21:
Q0 G Request (type DIA) cannot be processed
work process trace
please check the image
Thanks
ShradhaHello Divyanshu
It didnt create dev_vm.trc and VM_STACK_TRACE
And I am unable to provide dev_disp and dev_w* here due to size of the trace
But could the error be due to any of these parameters :
Parameters
Current
Changed
rdisp/max_vm_priv_time
2400
SERVLET=2400, RFC=2400
isp/max_vm_priv_no
3
SERVLET=3, RFC=3
rdisp/max_priv_time
600
3600
Maximum hold time for work processes in PRIV mode
rdisp/max_debug_lazy_time
600
3600
Maximum hold time for work processes in DEBUG mode
rdisp/appc_ca_blk_no
1000
1058
Buffer Size for CPI-C Communications
rdisp/wp_ca_blk_no
300
1058
Work Process Communication Blocks
vmcj/option/ps
960M
1460M
poolsize for the VMC
vmcj/option/gc/sharedWaterMark
90
70
VMC: watermark for shared garbage collector
vmcj/max_vm_heap_MB
64
128
max. vm heap
rdisp/keepalive
1200
3600
Timer for check of unused connections
rdisp/keepalive_timeout
60
150
Timeout for connection to SAPGUI
rdisp/wppriv_max_no
DEFAULT
16
Maximum number of work processes in PRIV mode -
PLease help me.....i wanna sign in icloud with different account but it says max number of free acconts reached
Somehow your Apple ID/iCloud account has been used on multiple iOS devices and exceeded the maximum. We have no way of knowing which devices. We are users like you on this forum.
-
Is there a max. number of Apple pro prints allowed per order with the updated iPhoto/Mountain Lion?
I have been using the system for years and have had no issues, but this first try under Mountain Lion I was told the max was 300 prints per order.
It order did not go through, nor did one with 65 photos. When I tried 2, it was fine, but at $2.99 shipping, plus tax,
paying $60 to get all 300 of my photos shipped is unreasonable.
Is this a glitch in the new OS? Hopefully it will be fixed.Hi blabla12345,
(untested and without warranty)
replace this line:
const sSaveCUBE = "CUBE";
with this:
const sSaveCUBE = "cube";
Have fun -
REPORT BUILDER: MAX. NUMBER OF RECORDS PER PAGE
Dear Consultant,
Using DEVELOPER 2000 R2.1 REPORT BUILDER, is there any way to set the " MAXIMUM NUMBER OF RECORDS PER PAGE" dynamically by user input when calling the report, without the need to modify the report at Design time and recompile it?
Thanks for your help.
Ghia Haidar
Developer
Astrolabe IT - Professional Consultants
Beirut, Lebanon
Phone: + 961 1 841.050
Fax: + 961 1 841.055 www.astrolabe.com.lb
nullRefer Manish question.
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Ali DHAINI ([email protected]):
Dear Consultant,
Using DEVELOPER 2000 R2.1 REPORT BUILDER, is there any way to set the " MAXIMUM NUMBER OF RECORDS PER PAGE" dynamically by user input when calling the report, without the need to modify the report at Design time and recompile it?
Thanks for your help.
Ghia Haidar
Developer
Astrolabe IT - Professional Consultants
Beirut, Lebanon
Phone: + 961 1 841.050
Fax: + 961 1 841.055 www.astrolabe.com.lb
<HR></BLOCKQUOTE>
null -
Max number of chars in process message MSEL?
Hi, what is the max number of characteristics can be used in process message category's MSEL table? Right now, I am using more than 99 characteristics and I get a short dump DYNPRO_FIELD_CONVERSION. Is it really limited to 99 characteristics and if it is true, is there an OSS note to change it to allow more than 99?
Thanks and points availablePlease make sure that you build a
multithreaded program first (check with ldd).
If anyone can tell me the maximum number of threads per process I would
really appreicate it.
Also the maximum number of open files per process. It depends on the architecture (x86/SPARC), OS version,
64 or 32-bit, /etc/system, shell limitations (/usr/bin/ulimit) ...
Search for "rlim_fd_max / rlim_fd_cur" on docs.sun.com too.
HTH,
-vladimir -
Max number of records in MDM workflow
Hi All
Need urgent recommendations.
We have a scenario where we need to launch a workflow upon import of records. The challenge is source file contains 80k records and its always a FULL load( on daily basis) in MDM. Do we have any limitation in MDM workflow for the max number of records? Will there be significant performance issues if we have a workflow with such huge number of records in MDM?
Please share your inputs.
Thanks-RaviHi Ravi,
Yes it can cause performance overhead and you will also have to optimise MDIS parametrs for this.
Regarding WF i think normally it is 100 records per WF.I think you can set a particular threshold for records after which the WF will autolaunch.
It is difficult to say what optimum number of records should be fed in Max Records per WF so I would suggest having a test run of including 100/1000 records per WF.Import Manager guide say there are several performance implications of importing records in a WF,so it is better to try for different ranges.
Thanks,
Ravi -
Max number of rows in a BEX structure
Hi gurus,
we need to create a structure with 164 key figures, and before starting doing it, does anybody knows which is the max number of rows that can be created on a BEX structure?
I'm not asking about max number of rows on a query, i'm asking about the number of entries that you can manually create on a structure. Is there a maximum?
Thanks in advance,
regards,
MiguelHi Migual,
You can add as per your requirement. Please refer the following link
http://help.sap.com/saphelp_nw04/helpdata/en/4d/e2bebb41da1d42917100471b364efa/content.htm
Assign Points if helpful.
Regards,
Amit
Maybe you are looking for
-
Matching an "Edit Text" in a form with a Field in a Table
Hi Every Body, I've succeed to add a new "Edit Text" in the invoice Form (133) with c# : oItem = oInvoiceForm.Items.Item("103"); oNewItem = oInvoiceForm.Items.Add("EditText1", SAPbouiCOM.BoFormItemTypes.it_EDIT);
-
Connecting to a database over the internet
Hello , Ok heres an interesting question - I would like to have an applet running on my browser which needs to connect to a central server over the internet, which in turn will need to connect to a database and query some results. These results will
-
Copy one text file to another text file and delete last line
Hi all wonder if someone can help, i want to be able to copy one text file to another text file and remove the last line of the first text file. So currently i have this method: Writer output = null; File file = new File("playerData.xml");
-
Dear SAP experts, my client is facing with one problem . one service PO is there in other than company code currency that is in (EURO), Tthy have posted service entry sheet on jan 12th 2010 that exchange rate is 1 euro = 35.5 QAR (Qatra real) and t
-
Java library to extract html tags in the given text
hello friends i would like to know is there any java library available through which i can accesss the html tags that are present in my simple text waiting for reply