MAX unable to recognize software/hardware

Hi
I re-installed Labview 7.1 multiple times without success. For some reason, the Measurement and Automation Explorer (MAX) does not recognize any of my National Instrument software that I have installed, nor does it recognize the DAQ Signal Accessory device that I have plugged into my PCI-6251 slot. When I open MAX, the software and hardware panel on the left side shows nothing. Has anyone encountered such a problem? What are some possible solutions?

Hi Peter,
It could be that some of the data files that MAX looks at are
preventing new information from working. In order to make sure
that some old files are not interfering with your present operation
follow the steps below:
Go to C:\Program Files\National Instruments\MAX and find the Data folder.
Copy this folder to a different location and rename it.
Delete the original Data folder.
Reboot your computer
Launch MAX
Refresh Devices (View > Refresh F5)
You should be able to now see your devices in MAX. If you are
still having problems, see if you can run an example program without
setting up the devices in MAX. If you are able to do that we can
see if the problem is in MAX, LabVIEW, or maybe the devices cannot be
seen by the operating system.
Best of luck!
Otis
Training and Certification
Product Support Engineer
National Instruments

Similar Messages

Unable to recognize blank DVD+R

When I insert a blank DVD+R into the cd/dvd drive, the system goes through its usual gyrations and then about 15 seconds later the drive bay opens, and there are no error messages. It appears that the drive or system is unable to recognize a blank DVD+R disc.
There isn't a problem viewing DVDs (commercial or superdrive burned discs)
iMac PowerPC G4 800Mhz Flatpanel Mac OS X (10.3.9) SuperDrive

Apple change the Open Firmware with the 10.4.6 Update! That's the problem that now no DVDs will be recognized by the system.
It's no Hardware problems! It's the software. Burning DVDs was problematical since 10.4.0 and Apple did a worst work.....with every Update since 10.4.4 it's even worster...
So, with the change of the firmware its not possible to burn DVD with Panther or earlier Tiger Versions as well because all of these Mac OS X Versions useing the changed Open Firmware.... :((
So, if Apple doesn't change it one more time you still have a non working SuperDrive on every Release of OS X

Imovie on my ipad ...refuses to recognize AVCHD Video. Also when i remove video clips already used in a project, it is unable to recognize missing clips after I've put them back. How do I get around these 2 issues?

My iMovie refuses to recognize, import, or work with AVCHD Video. It also refuses the same video clips even after I have converted them to Mp4. Also, when I delete a video clip already used in a project, then later import the same clip back to my ipad, the software is unable to recognize and find the clip again! Help! How do I get around these issues?

Hi Craig,
I also got the second problem. The storyboard on iMovie trailer has all these missing videos. If I import them on my iPad it doesn't find them.
If you find a solution it would be much appreciated to share it here ... I'll do the same.
Thanks,
Rafael

Unable to recognize USB modem

Dear Friends,
I have upgraded to Lion 10.7 and I face this issue:
My MacBook Pro unable to recognize my USB modem. It says "USB modem disconnected or unavailabe"
I have uninstalled and installed the USB modem but it shows the same error.
What could be the problem? All softwares are up to date.
Any help appreciated

Thanks dobwalls,
I solved my problem with BANYM's BLOG.
( http://www.banym.de/mac/huawei-umts-usb-stick-with-snow-leopard ) Its awsome
I used dashboard installer located on ( http://www.huaweidevice.com/resource/mini/200910149695/testmobile1014/index.html ?directoryId=3874&treeId=0 )
Here are the steps I made to solve this problem:
1) connected my USB stick to my Mac Book Pro.
2) Downloaded the first package on http://www.banym.de/mac/huawei-umts-usb-stick-with-snow-leopard
3) Used the dashboard to find the installation package located in resouarces folder of USB stick.
4) completed the installation successfully
Then it works
Thank you for your answers here, it was a big help to find this solution
Best Regards.

MAX 2.0 recognizes my PC-TIO-10 but I cannot use the counters with MAX.

MAX 2.0 recognizes my PC-TIO-10 board and can even run the test panel. However, only the digital I/O channels are available for configuration. Why is this? Would be nice to configure the counters too.

You can test your counters of the PCI-TIO-10 in MAX when you click on the Counter IO tab of the Test Panel. You can test Pulse Train Generation, Single Pulse Generation, and Simple Event Counting.
If you want to test Pulse Train Generation, you can set the frequency and the duty cycle. If you want to test Single Pulse Generation, you can choose the pulse delay and width. If you want to test Simple Event Counting, you specify what your Source is and make the physical connection, if necessary.
You didn't mention what version of NI-DAQ driver software you are using. The latest version to support your board is NI-DAQ 6.9 which does use MAX 2.0.
If you are not seeing the options I mentioned above, then perhaps you installed on top of an older version of NI-DAQ, causi
ng conflicts in the software. In that case, you want to uninstall all references to NI-DAQ to clean your machine and then do a fresh install of NI-DAQ 6.9.
Regards,
Geneva L.
Applications Engineer
National Instruments
http://www.ni.com/ask

Help Unable to use software upgrade

I am unable to use software upgrade, til yesterday it was running fine, today i am not getting the updates, the page is completly blank, but still says , your computer has softwares to be upgraded.why has this problem occured.I know i can download everything individually, but i need my mbp to do it automatically, as my net is slow.

3rd party pluggs or Logic instruments? Did you change hardware or installed/updated your software? I have a similar problem after an update where logic can't open 3rd party pluggs... But then I can open them on new projects... Strange!.....

Missing software/hardware/serial number.

Hey there.
I have a treo 750 AT&T branded that i got shipped over from the states when the came out and were still unavailable in Australia where i live.
Id love to be able to update it with the 2.25 but the AT&T one i downloaded says it only works with an updater with a service.
Should i be using an unbranded update or am i missing something.
Ironically as well when i hard reset my phone when i got it the software, hardware and serial number were erased in the start/system/about/phone.
Is there anyway to get them back so i can try to get a legit download that will work because this having the time messed up and unable to DST it is making feel like hitting something (probably the phone) with a hammer.
Any help would be appreatiated.
Cheers
Post relates to: Treo 750 (AT&T)

Ok. At this point I tell you, you have the update. Next thing to try is a hard reset of the device. Right now something is wrong with it you should have on that device a remote desktop in the start menu or in the programs. If it is not there we need to see if we can get the device back working correctly. Now this is up to you if you don't mine not seeing the software/hardware/or serial number and not having the remote desktop you do not need to hard reset.
to hard reset go here http://www.palm.com/cgi-bin/cso_kbURL.cgi?ID=887
If you have any questions post back.
Post relates to: Treo 800w (Sprint)

I am unable to update software or backup my devices. Apple techs unable to resolve the issue after hours of phone support over the course of several months.

I am unable to update software, transfer purchases, sync, or backup any of my 3 devices. I have tried using iTunes on other computers, uninstalling iTunes with tech support walking me through, using a different user on my computer, deleting photos off of my devices, using an ethernet cable instead of connecting with wifi, uninstalling my antivirus software and firewall, and had my laptop examined by several techs who all determined there was nothing wrong with the laptop that explains what has been going on. I am also unable to view or download purchases on iTunes. Clicking the Itunes store results in a blank white screen. I get various error messages, including -9886. Apple techs and now the engineers have been unable to resolve the issues thus far, even after several hours of phone support over the course of several months (about 5 hours this month alone). I have done everything they've suggested, even when they've suggested I do something over again, and I'm becoming frustrated. I would greatly appreciate any advice you can offer. Thank you in advance for your time.

Hi there
Sorry for hijacking your thread as put by Dahveed. However I have resolved my issue so I thought I'll share it with the rest of you.
I checked for the error 3194 in youtube and I found some good videos that tell you how to resolve the problem. The issue I was facing was the actually (I know because I have resolved it now) the communication between my computer and apple server which can be fixed as following (if you are using windows):
There is file in following directory:
C:\Windows/system32/drivers/etc/hosts
The file normally has no extension and it is in file format. You need to open it and make sure that every line that has apple server id starts with "#". In my case one of the line started directly with the ip address and then gs.apple.com.
Perform your restore/update after that and hopefully it should be resolved (mine did).
Cheers

ITunes unable to recognize iPod, error message along the lines if "iTunes has detected an iPod but unable to recognise" I have followed all the trouble shooting tips and am still stuck? I am now being told by a friend I need a link sent to me to fix this

Hi,
I am need of help! I have had this issue for a while now and it's becoming frustrating.
My iTunes installed on my HP Windows 8 Netbook is unable to recognize my iPod, the error message along the lines of "iTunes has detected an iPod but unable to recognise"
I have followed all the trouble shooting tips and am still stuck? I am now being told by a friend I need a link sent to me to fix this??
Someone please help me fix this problem.
Many thanks.
Matt.

Hi
So just close iTunes and re-open iTunes thats it and that worked for you?
When you say reset your settings do you mean to factory settings? As my iPod was swapped at the store for a new one and the problem is still there...
Thanks.

HT1386 I recently bought a new laptop and installed itunes. I was trying to sychronize my ipad and iphone, but it seems that the itunes was unable to recognize the devices. Can you tell me how I can solve this problem?

I recently bought a new laptop and installed itunes. I was trying to sychronize my ipad and iphone, but it seems that the itunes was unable to recognize the devices. Can you tell me how I can solve this problem?

how new is the Notebook ?
Also double check your firewalls and virus protection that they are not blocking any ports also make sure you are plugging in the fastest USB

Unable to recognize the server status in OEPE, shows error alert

Hi,
On windows 32 , I installed the WSL 10.3.3 + OEPE and the OSB 11g.
I have configured the a base_domain with a dtabse of 10g (10.3) Express edition.
When I try to start the server from OEPE (Eclipse), the server starts and the console show the server is RUNNING. Even I can connect to OSB Console from Browser.
However, the servers tab in the eclipse unable to recognize the status, and returns back to STOPPED with an Alert message "Server xxxx unable to start.
So I am not able to do anything in the OEPE, its urgent please, any help .
Thanks in advance.
-- Khaleel

Hi Ravi,
Thanks for the suggestion. Actually the server and domain all are running well. I can start and stop from the startup menus and command scripts.
The only issue is in the Eclipse (OEPE) when I try to connect the server. However I found the solution that I need comment the localhost entry in hosts file as below.
# 127.0.0.1 localhost
Now the server is connecting well. However I have another issue, that I am not able to shutdown the server from startup menus. I suspect the t3 protocal and HTTP protocal related. If you have any suggestions please help me.
Note: if still have issues then try by removing the LAN connection, or install the Microsoft Loopback Adapter.
But I am still looking for options without commenting the localhost in the hosts entry.
--Khaleel
Edited by: Khaleel Shaik on Dec 8, 2010 2:58 PM

Unable to read software component versions from System Landscape Directory

Hi XI,
Once I could import software component version but now I can't. Maybe I did something wrong in SLD.
Could you please give me some hints?
Thanks,
Bruce

hi,
i have also problem with "import software componenet version "
i got a message like
"unable to import software component version from
system landscape directory ......."
than i gone for SLDCHECK...i got an error it is ............
calling function LCR_LIST_BUSSINESS_SYSTEM
Retreiveing data from the sld server function call returned exception code 4
connection to sld does not work
check sld function and configuration
what that i have to do ...to make it work ....please give me any solution for that please give me detailed info
with regards
Edited by: praneeth mamgunta on Jun 27, 2008 4:04 PM
Edited by: praneeth mamgunta on Jun 27, 2008 4:07 PM

Unable to read software component version from System Landscape Directory "

I've worked in past creating/importing SWCV, but this is new system PI7.0 and stuck.
A) Is my understanding on resolution correct?
Should I go and apply notes 940309 and create client copy of existing client 001
                                    OR
change role of client 001; SXMB_ADMIN -> 'Integration Engine Configuration' to 'Integration Server'
I have no problem in using client 001 as Integration server, all I want is import of SWCV to work. Thanks. Appreciate the help.
B) Here is what I have done and the error:
1) Followed weblog below and created product, software component, technical system, business sytem in SLD.
/people/srinivas.vanamala2/blog/2007/02/05/step-by-step-guide-xml-file-2-xml-file-scenario-part-i
2) When I import the SWC from integration repository getting error
(Unable to read software component version from System Landscape Directory "server:5<system number>00").
C) Pointers used from the forum to debug the issue, but still no luck
Below are the points checked from the forum and all steps are correct, but still have issues with the import
1) check the RFCs SAPSLDAPI, LCRSAPRFC, connection test pass as the program ID registered with Jco
2) T-code SLDCHECK no errors (followed http://help.sap.com/saphelp_nw04/helpdata/de/78/20244134a56532e10000000a1550b0/content.htm)
3) T-code SLDAPICUST got user PIAPPLUSER, pwd is correct (reset the pwd)
4) logged using PIAPPLUSER http://server:port/sld and it works
5) One of the weblog SLD Check Failed (LCR_LIST_BUSINESS_SYSTEMS function doesn't work) referred to apply notes 940309
Notes: 940309
You are installing 'SAP NetWeaver 2004s SR1 ABAP+Java' Usage Type 'NetWeaver Process Integration (PI)'.
You don't want to use the default client 001, but another client as Integration Server.

applied portion (PIPostInstallProcess) of OSS notes 940309 and it resolved.
Note:
I still retained client 001 and didn't do client copy as mentioned in the notes. The wizard based CTC tool helped. Here are the details if someone has similar issue and want to know further details:
A NetWeaver Process Integration (PI) Installation (ABAP+Java) has two parts: Installation and configuration. The former is done by the Installer, the latter by the 'Central Template Configuration' (CTC) Tool.
http://help.sap.com/saphelp_nw04s/helpdata/en/14/39084136b5f423e10000000a155106/frameset.htm
1.      Call the wizard-based configuration tool as described in Configuration Wizard.
       2.      Select the scenario PI and the task PIPostInstallProcess.
       3.      Choose Execute.
A list of the steps to be executed by the wizard is displayed.
       4.      Choose Install.

Unable to read software component versions from System Landscape

Dear all,
I have an ECC system with ABAP and Java installed.
I already configured so that SLDCheck, RFC destination configuration run successfully.
PIAPPLUSER is not locked and can logon.
However, when I import software component version in Integration Builder, the system return error message "Unable to read software component versions from System Landscape Directory "Server:50000".
Please tell me how to correct this error.
Giang

Hi,
Check this
http://****************/Tips/XI/SWComponentError/Resolve.htm
"Unable to read software component versions from System Landscape Directory
Unable to read software component versions from System Landscape Directory
unable to import from SLD
Regards
Seshagiri

Unable to recognize document as valid XSDCheck the selected category

w.r.t the thread below, any solution expert..
Unable to convert imported document to WSDL --- PI 7.1
in Pi 7.0 XSD is working perfectly... in XML spy its not showing any error. but when i want to upload in 7.1 its giving errror like
Unable to convert imported document to WSDL
Reason:
Unable to recognize document as valid XSDCheck the selected category
what change i should make in the xsd... so that it can be imported in 7.1

Hi
What you can do is (in XML Spy) generate a sample XML file from your schema. Make sure you tick of for "Generate all elements".
From the sample XML file that you get, generate a schema (Generate DTD/Schema). This new schema will be different to the one you have, but importing it in PI should work.
When you use it in your message mapping, just make sure that you choose the correct field as the top node and also check that all fields are there (they were in my case and worked as a glove..:).
regards Ole

MAX unable to recognize software/hardware

Similar Messages

Maybe you are looking for