Maximum AA-ports NME-CUE version 7.0

Hi there,
What is the maximum number of AA-ports I can use with NME-CUE version 7.0?
Thanks
Sent from Cisco Technical Support iPhone App

Hello,
Please see Table-4 in the Release Notes:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel7_0/rel_notes/rel_notes.html
HTH,
Vishal

Similar Messages

NME-CUE Port adapter is disabled

Hi Guys, in need of a little help, i'm trying to install a NME-CUE into a CISCO3845 but the card is showing as disabled
Installed c3845-spservicesk9-mz.150-1.M10.bin and PVDM2-64
Slot 1:
        Integrated Service Engine Port adapter, 1 port
        Port adapter is disabled
        Port adapter insertion time unknown
        EEPROM contents at hardware discovery:
        Hardware Revision        : 1.0
        Part Number              : 73-10371-02
        Top Assy. Part Number    : 800-29801-01
        Board Revision           : A0
        Deviation Number         : 102999
        Fab Version              : 01
        PCB Serial Number        : FOC13232JXF
        RMA Test History         : 00
        RMA Number               : 0-0-0-0
        RMA History              : 00
        Product (FRU) Number     : NME-CUE
        Version Identifier       : V01
        CLEI Code                : IPUIA6NRAA
        EEPROM format version 4
        EEPROM contents (hex):
          0x00: 04 FF 40 04 F8 41 01 00 82 49 28 83 02 C0 46 03
          0x10: 20 00 74 69 01 42 41 30 88 00 01 92 57 02 01 C1
          0x20: 8B 46 4F 43 31 33 32 33 32 4A 58 46 03 00 81 00
          0x30: 00 00 00 04 00 CB 87 4E 4D 45 2D 43 55 45 89 56
          0x40: 30 31 20 D9 03 40 C1 CB C6 8A 49 50 55 49 41 36
          0x50: 4E 52 41 41 FF FF FF FF FF FF FF FF FF FF FF FF
          0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
          0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
any ideas on where to go from here
Many Thanks

It seems like issue with the CUE. But lets work it out step by step:
1) If you haven't configured the Router\CUE interface, please enable it and try to access CUE or check the CUE status from the router CLI. Here is a quick reference guide:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel7_0/install/Install/nuinstall.html
Do not forget to configure static route pointing CUE ip address to the CUE interface.
Let me know whats the output.
2) If nothing helps in step 1, your only option would be to reseat the CUE module and try in a different slot. Make sure to reboot the router. (as I think its not hot swappable)
3) If nothing above helps, then most probably time for RMA.
Apart from above, was it a working setup or you bought it second hand?
Can you also post an output of sh inventory?
-Terry
Please rate all helpful posts and mark the thread as answered if you have no other queries.

Cisco Unity Express (NME-CUE) Compatibility for CUCM 9.1.2

I unable to find latest Compatibility matrix for Cisco Unity Express (NME-CUE) module for integrating with CUCM 9.1.2
The URL: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html is updated with CUCM 9.0 only.
Request to share Compatibility matrix or suggest Hardware and software for my below requirement.
I am running NME-CUE 7.0.6 on 2951 ISR2 with IOS version 15.2(4)M5 and integrated with CUCM 7.1.5 using SCCP.
I am upgrading my CUCM to 9.1.2 and need suggestion on upgrading the CUE.
Also need details on Licensing for approx 100 Mailbox and 25 Voice Ports (No need of IVR Ports).
Thanks,
Chandan

Hi Chandan,
CUE 8.6.6 and later are compatible with CUCM 9.1.x;
Support for Cisco Unified Communications Manager 9.1
Cisco Unity Express 8.6.6 provides support for Cisco Unified Communications Manager 9.1.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel8_6/rel_notes/rel_notes86.html#pgfId-411381
Because you are moving from a pre-7.1 CUE version you will need to follow the CSL License migration process;
NoteWhen you upgrade to Cisco Unity Express Release 8.6.x from any release prior to Cisco Unity Express Release 7.1, you must replace your pre-CSL licenses with CSL licenses. You must migrate your licenses for the mailbox features and port features. If you have purchased the optional IVR features, you should also migrate your licenses for the IVR features.
Software Activation for Cisco Unity Express 7.1 and Later Versions
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/rel7_1/Licensing/CUELicensing_book.html
Cheers!
Rob

Cisco Unity Express NME-CUE %ARP-4-NULL_SRC_MAC

Hi
I have connected NME-CUE to the router C2811. The module works all good for voicemail. Now, when Im trying to upgrade the software from version 7.1.6 to 8.6.7, using the 'Clean Install Method' it wont work. From the "BOOT-ASM" menu, after pressing ***, Im not able to reach anywhere. Not even the default gateway which is on the router. Whenever I try to reach some IP Address, out of module, it throws the following error in the ROUTER's log.
Feb 9 22:19:13: %ARP-4-NULL_SRC_MAC: NULL MAC address from 192.168.11.250 on In1/0
I have searched for this error and could not find any useful reference to this error message.
Saif

Here is the document used:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel8_6/install/boothelp.html
And this is the Interface config:
interface Integrated-Service-Engine1/0
ip unnumbered FastEthernet0/0.1
ip nat inside
ip virtual-reassembly in
service-module ip address 192.168.11.250 255.255.255.0
!Application: CUE Running on NME
service-module ip default-gateway 192.168.11.1
no keepalive
end
and here is the static route:
ip route 192.168.11.250 255.255.255.255 Integrated-Service-Engine1/0

Disabling port 389 for version 4.x/5.x of the Directory server?

Is it possible to close port 389 for version 4.x/5.x of the Directory server?
We need to ony enable 636 for SSL communications. WE currently limit 389 access to the CMS (which oddly enough <bold>requires</bold> it - ARRGGGG!) by IP Address. We're currently running NT 4 and have turned off 389 and found that there is a need to have 389 open for some initial operations (ignoring the CMS requirement for testing). We have not fully tested this under Solaris ... but anticipate the same to be true.
Rich

iPlanet Directory Server 5 can run without the 389 port enabled... You need to set the LDAP port to 0.
However, this will prevent the Console and the Admin Server from working correctly. It is OK if you do all the administration of your server using command line utilities.
Regards,
Ludovic.

Configure connectivity on nme-cue

My nm-cue died and all we have as a replacement is a nme-cue. I tried to apply the current config from the nm-cue to the nme-cue and I can't ping it from the router to the nme-cue.
This was the working config from the NM-CUE
FastEthernet0/0.20 10.3.3.1 YES NVRAM up up
interface Service-Engine1/0
description $FW_INSIDE$
ip unnumbered FastEthernet0/0.20
service-module ip address 10.3.3.5 255.255.255.0
service-module ip default-gateway 10.3.3.1
ip route 10.3.3.5 255.255.255.255 Service-Engine1/0
I applied this on the NME-CUE and it doesn't ping
Cisco website has the config for the NME-CUE as:
Router(config)# interface Service-Engine 1/0
Router(config-if)# ip address 10.0.0.9 255.0.0.0
Router(config-if)# service-module ip address 10.0.0.10 255.0.0.0
Router(config-if)# service-module ip default-gateway 10.0.100.10
Router(config-if)# exit
I could ping from the router to the nme-cue with a different subnet following this config but I do not want to place the service engine on another subnet.
I retried it with
interface Service-Engine 1/0
ip unnumbered FastEthernet0/0.20
service-module ip address 10.3.3.5 255.255.255.0
service-module ip default-gateway 10.3.3.1
It didn't mention to add a static route so I left it out. Couldn't ping so I added the static route:
ip route 10.3.3.5 255.255.255.255 Service-Engine1/0
Still can't ping
Any help would be greatly appreciated.

Yes from the router I can ping the tftp server.
No the router cannot ping the service module
No I cannot ping the tftp-server from the service module address 10.3.3.5 even after I set the configs in bootloader mode.
S      10.3.3.5/32 is directly connected, Integrated-Service-Engine1/0
R2811#sh run | s ip route
ip route 10.3.3.5 255.255.255.255 Integrated-Service-Engine1/0
R2811#
R2811#sh ip int bri
Interface                  IP-Address      OK? Method Status                Protocol
FastEthernet0/0            unassigned      YES NVRAM up                    up
FastEthernet0/0.20        10.3.3.1          YES NVRAM up                    up
FastEthernet0/1            unassigned      YES NVRAM administratively down down
In1/0                      10.3.3.1                 YES TFTP   up                    up
The router and tftp server are on the same subnet so it doesn not need a static route.
I'm pretty stumped..

Help open port on ASA5510 (version 8.3)

Hi all,
I configured ASA to open port 21, 3389, 5900 (outside access in) but when i check port just success : 21 and 3389, Error: 5900
If i configured with only one port 5900 or 3389, is't ok, i don't undesrtand what 's the problem?
ASA5510>
ASA5510> ena
Password: ***********************
ASA5510# show run
: Saved
ASA Version 8.3(1)
hostname ASA5510
domain-name lohoi.local
enable password *********************** encrypted
passwd *********************** encrypted
names
interface Ethernet0/0
description Connect_to_Modem
nameif outside
security-level 0
ip address 10.0.0.2 255.255.255.0
interface Ethernet0/1
description Connect_to_Router2911
nameif inside
security-level 100
ip address 172.16.17.2 255.255.255.240
interface Ethernet0/2
shutdown
no na
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
description Management
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
ftp mode passive
clock timezone ICT 7
dns server-group DefaultDNS
domain-name lohoi.local
object network obj-any
subnet 0.0.0.0 0.0.0.0
object network ftpserver
host 192.168.88.90
description FTP server
object network Remote_Desktop
host 192.168.100.29
object network VNC
host 192.168.100.4
access-list 101 extended permit icmp any any
access-list 101 extended permit icmp any any echo-reply
access-list 101 extended permit tcp any any
access-list outside_access_in extended permit tcp any object ftpserver eq ftp
access-list outside_in extended permit tcp any host 192.168.100.29
access-list outside_in extended permit tcp any host 192.168.100.4
pager lines 24
mtu outside 1500
mtu inside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst
asdm image disk0:/asdm-631.bin
asdm history enable
arp timeout 14400
object network obj-any
nat (inside,outside) dynamic interface
object network ftpserver
nat (inside,outside) static interface service tcp ftp ftp
object network Remote_Desktop
nat (inside,outside) static interface service tcp 3389 3389
object network VNC
nat (inside,outside) static interface service tcp 5900 5900
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.0.0.1 1
route inside 192.168.88.64 255.255.255.224 1
route inside 192.168.100.0 255.255.255.0 172.16.17.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http authentication-certificate inside
http authentication-certificate management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password *********************** encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:667cb3ec729681c78ccab9a57abd89df
: end
ASA5510#

ASA5510# show run
: Saved
ASA Version 8.3(1)
hostname ASA5510
domain-name lohoi.local
enable password ****************** encrypted
passwd ****************** encrypted
names
interface Ethernet0/0
description Connect_to_Modem
nameif outside
security-level 0
ip address 10.0.0.2 255.255.255.0
interface Ethernet0/1
description Connect_to_Router2911
nameif inside
security-level 100
ip address 172.16.17.2 255.255.255.240
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
description Management
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
ftp mode passive
clock timezone ICT 7
dns server-group DefaultDNS
domain-name lohoi.local
object network obj-any
subnet 0.0.0.0 0.0.0.0
object network ftpserver
host 192.168.88.90
description FTP server
object network remote_desktop
host 192.168.100.2
object network remote_vnc
host 192.168.100.4
access-list 101 extended permit icmp any any
access-list 101 extended permit icmp any any echo-reply
access-list 101 extended permit tcp any any
access-list outside_access_in extended permit tcp any object ftpserver eq ftp
access-list outside_access_in extended permit tcp any host 192.168.100.4 eq 5900
access-list outside_access_in extended permit tcp any host 192.168.100.2 eq 3389
pager lines 24
mtu outside 1500
mtu inside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asd
asdm history enable
arp timeout 14400
object network obj-any
nat (inside,outside) dynamic interface
object network ftpserver
nat (inside,outside) static interface service tcp ftp ftp
object network remote_desktop
nat (inside,outside) static interface service tcp 3389 3389
object network remote_vnc
nat (inside,outside) static interface service tcp 5900 5900
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.0.0.1 1
route inside 192.168.88.64 255.255.255.224 172.16.17.1 1
route inside 192.168.100.0 255.255.255.0 172.16.17.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http authentication-certificate inside
http authentication-certificate management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password ****************** encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:4f061a213185354518601f754e41494c
: end
ASA5510#
So i configured again, but i'm not to access to 5900 port

Upgrading CUE 7.0 to CUE 8.6 on Cisco 2821 NME-CUE

Hi guys,
I read that migration form CUE 7.0 to 8,6 if possible, but I dont undersantd for license, this link tell that I contact with license page for migrate the license of mi actualy CUE 7.0, the question is, this migration has a cost? o is free i only need contact to team license.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel7_1/Licensing/CUELicense.pdf
Thanks for your help.

Hi Roberto,
There is no cost (free) to migrate to CSL Licenses
Migrating to CSL Licenses
When you upgrade to version 7.1 or later, you must replace your pre-CSL licenses with CSL licenses. You are required to migrate your licenses for mailbox features and port features. If you purchased the optional IVR features, you must also migrate your licenses for the IVR features. The migration procedure for each of these types of licenses are described in a separate section below.
Note If you are upgrading to the same of licensed features as before, the CSL licenses are free.
When you obtain licenses for features for Cisco Unity Express 7.1 or later, the licenses are available only in the increments shown below. The following types of licenses are available:
•Mailboxes (available only in increments of five)
•Ports (available only in increments of two)
•IVR (available only in increments of two)
Note CSL licenses are the same for all supported devices. See the Release Notes for Cisco Unity Express for a list of supported devices.
The corresponding SKUs for these licenses are:
•FL-CUE-MBX-5
•FL-CUE-PORT-2
•FL-CUE-IVR-2
•FL-TCV-USER-1
To migrate to CSL licenses, use the following procedure:
1. Use the show software license command to determine which pre-CSL licenses you have.
The name of the pre-CSL licenses include the incremental quantity of the license. For example SCUE-LIC-25CME.
2. For mailboxes, add the number of GDMs (Group Delivery Mailboxes) that you will be using because they were not included in the pre-CSL counts but are now being represented in the CSL counts.
3. Divide the total number of pre-CSL licensed features by the incremental quantity represented in the name of the appropriate CSL SKU.
For mailboxes, divide by five. For ports, divide by two. For IVR sessions, divide by two.
If the result is not a whole number, round up. This will give you the explicit quantity of CSL incremental licenses that you need.
As an example, if you have the following pre-CSL licenses and you have 10 GDMs:
•SCUE-LIC-100CCM
•8 instances of SCUE-LIC-PORT-2
•SCUE-IVR-S16
You will need to choose:
•22 instances of FL-CUE-MBX-5
•8 instances of FL-CUE-PORT-2
•8 instances of FL-CUE-IVR-2
Using the Migration Portal
Note You must have a Cisco.com password to access some of the URLs in the following procedure.
Follow these steps to obtain a migration license for your existing Cisco Unity Express 7.1 features:
Step 1 Go to the licensing portal at www.cisco.com/go/license and click the link at the bottom of the page to go to the license migration portal.
Step 2 On the router that is running the features that you want to migrate, enter the show inventory command to see the corresponding product IDs and serial numbers.
Step 3 Enter the appropriate product ID and the serial number and click Continue.
The product ID is the type of Network Module that you are using, such as AIM-CUE.
Step 4 Use the drop-down menus to select the product family, product, and feature (SKU), then click Continue.
For the product, use the SKU that you determined in the previous section for the features that you want to migrate.
Enter your registration information, including your company's name and e-mail address, then click Continue.
Step 5 Verify all of your license information and click Submit to receive the free CSL upgrade license file by e-mail.
Step 6 Repeat the appropriate steps above for each device that is running features that you want to migrate.
Step 7 Copy the license file(s) to a FTP or TFTP server.
From this good doc;
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel7_1/Licensing/Using_CSL.html#wp1102792
Cheers!
Rob

CUE 8.5.1 NME-CUE web page setup no setup initialization and error: Login to CUCME failed

When first login in via the web page. When going to Configure menu and choosing CUCME to enter it manually, I get:
Error: Login to CUCME failed with the new values. Check the new CUCME configuration and enter the correct values.
hostname: 172.23.0.1
web user name: admin
web password: cisco
Sip gateway hostname: 172.23.0.1
ccn reporting historical
database local
description "se-172-23-0-2"
end reporting
ccn subsystem sip
gateway address "172.23.0.1"
mwi sip unsolicited
end subsystem
BR2-ROUTER#sh run
Building configuration...
Current configuration : 5264 bytes
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname BR2-ROUTER
boot-start-marker
boot-end-marker
card type t1 0 3
logging message-counter syslog
logging buffered 51200 warnings
no aaa new-model
clock timezone MST -7
clock summer-time MDT recurring
network-clock-participate wic 3
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 172.21.0.1 172.21.0.49
ip dhcp excluded-address 172.21.0.59 172.21.0.254
ip dhcp excluded-address 172.20.0.1 172.20.0.10
ip dhcp pool CME
   network 172.21.0.0 255.255.255.0
   option 150 ip 172.21.0.1
   default-router 172.21.0.1
ip dhcp pool LAPTOPS
   network 172.20.0.0 255.255.255.0
   default-router 172.20.0.2
   dns-server 10.10.10.1
no ip domain lookup
ip domain name wilson.com
no ipv6 cef
multilink bundle-name authenticated
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service h225-notify cid-update
sip
bind control source-interface GigabitEthernet0/0.20
bind media source-interface GigabitEthernet0/0.20
registrar server expires max 600 min 60
voice register global
mode cme
source-address 172.21.0.1 port 5060
max-dn 4
max-pool 4
authenticate register
timezone 12
time-format 24
date-format YY-M-D
voicemail 3600
tftp-path flash:
create profile sync 0021447056000116
ntp-server 174.137.67.50 mode directedbroadcast
voice register dn 1
number 3006
call-forward b2bua busy 3600
call-forward b2bua mailbox 3006
call-forward b2bua noan 3600 timeout 12
name rp-sip-1-16
label SIP 511-5016
mwi
voice register pool 1
id mac FCFB.FBCA.30CE
type 7965
number 1 dn 1
dtmf-relay rtp-nte
username 3006 password cisco
description 687-3006
codec g711ulaw
voice-card 0
username admin privilege 15 secret 5 $1$..D.$orbTsqgPSvNkMpfjjkg5q.
archive
log config
hidekeys
controller T1 0/3/0
cablelength long 0db
controller T1 0/3/1
cablelength long 0db
interface Loopback0
ip address 172.23.0.1 255.255.255.252
ip ospf network point-to-point
interface GigabitEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$
no ip address
duplex auto
speed auto
interface GigabitEthernet0/0.10
encapsulation dot1Q 10 native
ip address 172.20.0.2 255.255.255.0
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
ip address 172.21.0.1 255.255.255.0
interface GigabitEthernet0/0.30
encapsulation dot1Q 30
ip address 172.22.0.1 255.255.255.0
interface GigabitEthernet0/1
ip address 192.168.1.138 255.255.252.0
duplex auto
speed auto
interface Integrated-Service-Engine1/0
ip unnumbered Loopback0
service-module ip address 172.23.0.2 255.255.255.252
service-module ip default-gateway 172.23.0.1
no keepalive
ip forward-protocol nd
ip route 172.23.0.2 255.255.255.255 Integrated-Service-Engine1/0
ip http server
ip http access-class 23
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:/gui
access-list 23 permit 10.10.10.0 0.0.0.7
nls resp-timeout 1
cpd cr-id 1
control-plane
ccm-manager fax protocol cisco
mgcp fax t38 ecm
dial-peer voice 3600 voip
destination-pattern 36..
session protocol sipv2
session target ipv4:192.168.1.144
dtmf-relay sip-notify
codec g711ulaw
no vad
sip-ua
retry invite 3
timers trying 400
mwi-server ipv4:192.168.1.144 expires 3600 port 5060 transport udp
gatekeeper
shutdown
telephony-service
no auto-reg-ephone
em logout 0:0 0:0 0:0
max-ephones 10
max-dn 10 no-reg both
ip source-address 172.23.0.1 port 2000
voicemail 3600
max-conferences 8 gain -6
call-forward pattern .T
web admin system name admin password cisco
dn-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 3007
description 687-9898-3007
name Vatos locos
call-forward busy 3600
call-forward noan 3600 timeout 12
ephone-dn 2
number 3008
description 687-9898-3008
name Vatos locos2
call-forward busy 3600
call-forward noan 3600 timeout 12
ephone-dn 3 octo-line
number 3009
huntstop channel 6
ephone-dn 4
number 7999....
mwi on
ephone-dn 5
number 7998....
mwi off
ephone 1
device-security-mode none
description TESTTTTT
mac-address FCFB.FBCA.3406
max-calls-per-button 5
busy-trigger-per-button 4
type 7965
button 1:1 2:3
ephone 2
device-security-mode none
description TESTTTTT
mac-address FCFB.FBCA.3030
max-calls-per-button 4
busy-trigger-per-button 3
type 7965
button 1:2 2:3
line con 0
exec-timeout 0 0
logging synchronous
login local
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input telnet
line vty 5 15
access-class 23 in
privilege level 15
login local
transport input telnet
scheduler allocate 20000 1000
ntp server 174.137.67.50
end
BR2-ROUTER#
Apr 12 2011 16:23:12 gui/admin_user.js
122     585532 Mar 30 2011 05:48:46 phone/7975/cnu75.8-3-2-27.sbn
123    2453636 Mar 30 2011 05:48:56 phone/7975/cvm75sccp.8-3-2-27.sbn
124     326315 Mar 30 2011 05:48:58 phone/7975/dsp75.8-3-2-27.sbn
125     557786 Mar 30 2011 05:49:00 phone/7975/jar75sccp.8-3-2-27.sbn
126        638 Mar 30 2011 05:49:02 phone/7975/SCCP75.8-3-3S.loads
127        642 Mar 30 2011 05:49:02 phone/7975/term75.default.loads
128          0 Mar 30 2011 05:49:02 phone/7941-7961
129    2494499 Mar 30 2011 05:49:12 phone/7941-7961/apps41.8-3-2-27.sbn
130     547146 Mar 30 2011 05:49:16 phone/7941-7961/cnu41.8-3-2-27.sbn
131       2340 Apr 02 2011 03:55:02 April012011.txt
132       3579 Apr 12 2011 03:52:42 softkeyDefault_kpml.xml
133         69 Apr 12 2011 03:52:40 syncinfo.xml
134       2682 Apr 12 2011 03:52:42 SEPFCFBFBCA30CE.cnf.xml
135       1882 Apr 12 2011 03:52:42 SIPDefault.cnf
136       3613 Apr 12 2011 03:52:42 softkeyDefault.xml
137       3987 Apr 12 2011 16:23:10 gui/admin_user.html
138       1029 Apr 12 2011 16:23:14 gui/CiscoLogo.gif
139        617 Apr 12 2011 16:23:14 gui/CME_GUI_README.TXT
140        953 Apr 12 2011 16:23:14 gui/Delete.gif
141      16344 Apr 12 2011 16:23:14 gui/dom.js
142        864 Apr 12 2011 16:23:16 gui/downarrow.gif
143       6146 Apr 12 2011 16:23:16 gui/ephone_admin.html
144       4558 Apr 12 2011 16:23:16 gui/logohome.gif
145       3866 Apr 12 2011 16:23:16 gui/normal_user.html
146      78428 Apr 12 2011 16:23:18 gui/normal_user.js
147       1347 Apr 12 2011 16:23:18 gui/Plus.gif
148        843 Apr 12 2011 16:23:18 gui/sxiconad.gif
149        174 Apr 12 2011 16:23:18 gui/Tab.gif
150       2431 Apr 12 2011 16:23:20 gui/telephony_service.html
151        870 Apr 12 2011 16:23:20 gui/uparrow.gif
152       9968 Apr 12 2011 16:23:20 gui/xml-test.html
153       3412 Apr 12 2011 16:23:20 gui/xml.template

Fixed. Routing issue:
Routing issue:
ip http access-class 23 !!!!!! Preconfigured from Factory
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip http path flash:/gui
access-list 23 permit 10.10.10.0 0.0.0.7 !!!!!! Preconfigured from Factory
To fix
No ip http access-class 23

Can't import CTI Ports in CUE 3.1

Hi Everyone,
I have recently migrated CallManager 4.1 to CUCM 7.1. Everything is working fine but CUE is not able to integrate with CUCM 7.1
I have provided the new credentials for Admin User and JTAPI user in CUE 3.1 and also made a new application user in CUCM 7.1.
When I verify CallManager Admin User in CUE web interface it shows Admin login successful, JTAPI login successful.
But when I try to search and import CTI Ports from CallManager, it shows me the error IOException: No such attribute.
Can anyone please help me with this issue?
Thanks,
Amit.

Hi
See this compatibility chart:
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.htm#CUCM
To run CM7.1, you need to be running 3.2.1 of CUE as a minimum.
Regards
Aaron
Please rate helpful posts...

Want to know Maximum size limit for TimesTen version 5.1.x

Hello,
I know that in prior releases the maximum TimesTen database size limit was 2GB.I got this info from one of the TimesTen documentation.
As of now Im using version 5.1.x.Here Im not able to get any info regarding the maximum size limit of a TimesTen datastore. Please help me
Thanks In Advance
Pratheej

Also be aware that on Windows you can rarely achieve a data store size of >1g
It's down to the way Windows handles it'd DLLS - they tend to get loaded in a fragmented way and since TimesTen needs one contiguous slice of shared memory this causes a problem.

NME-CUE stuck in waiting after upgrade from 8.5 to 8.6

Hi,
I have been trying to upgrade our CUE from 8.5.4 to 8.6.4, but after the upgrade it is stuck in the below stage. Any help would be much appreciated.
Welcome to Cisco Service Engine
Power button monitor started
Setting the system time from hardware clock
********** rc.aesop ****************
Populating resource values from /etc/bryce_rsrc_file
attribute ios_rbcp/app_cookie_id exists
Populating resource values from /etc/default_rsrc_file
Populating resource values from /etc/products/cue/default_rsrc_file
Populating resource values from /etc/products/cue/bryce_rsrc_file
Processing manifests . . . . . . . . . . . . . complete
==> Management interface is eth0
==> Management interface is eth0
Serial Number: FOC15080XED
INIT: Entering runlevel: 2
********** rc.post_install ****************
INIT: Switching to runlevel: 4
INIT: Sending processes the TERM signal
==> Starting CDP
STARTED: ntp_startup.sh
STARTED: LDAP_startup.sh
STARTED: SQL_startup.sh
STARTED: dwnldr_startup.sh
STARTED: HTTP_startup.sh
STARTED: probe
STARTED: fndn_udins_wrapper
STARTED: superthread_startup.sh
STARTED: /usr/wfavvid/run-wfengine.sh
STARTED: /usr/bin/launch_ums.sh
Waiting 27 ...
Waiting 605 ...

Post Author: blairwheadon
CA Forum: Upgrading and Licensing
In the Database Expert, bring up the Options dialog. I think it's on the right click menu. You can then enter a filter for the table name and owner using wildcards. This will limit the number of tables presented and allow you to see the new view.
Thanks, Blair

My ipod, 4th generation, squeals and pops via the headphones when connected to my computer, by the USB, port running itunes version 10. Any idea what is wrong?

I have tried to five r's and using different usb ports. I have also cleaned the contacts recently but I still have the same annoying sounds. Any advice will be warmly received.

Does the iPod appear in iTunes on another PC or Mac running iTunes?
Did you follow the instructions in this Apple support document when removing and re-installing iTunes and all Apple related software? If not, work through these instructions exactly as they are.
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
B-rock

Advanced Auto Smart Ports 2960S IOS Version 15.0(2)SE2

Hello again
After several days on the lab I have got a Smart Install and Automatic Smart Ports Zero touch configuration almost ready to deploy on our network. I am just having a last issue.
The configuration of my 2960S is ok and they detect other switches on the ASP ports and everything is fine.. BUT.. after about 2.40mns with no cables being unplugged the switch forgets that port gi1/0/6 fx has a Catalyst Switch connected to it and discovers one unclassified device executing CISCO_LAST_RESORT_EVENT macro which has other access ports and so on.
I have no idea what could be triggering something like this. I have ried several debug commands but nothing seems to be the trigger.
Logs:
Jun 11 09:34:26.556: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/6, changed state to up
HX927438_SW43(config-if)#
Jun 11 09:34:28.616: %AUTOSMARTPORT-5-INSERT: Device Cisco-Switch detected on interface GigabitEthernet1/0/6, executed BUF_SWITCH
Jun 11 09:34:28.622: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/6, changed state to up
Jun 11 09:34:28.637: %SYS-5-CONFIG_I: Configured from console by tty17
HX927438_SW43(config-if)#
Jun 11 09:37:13.286: %SYS-5-CONFIG_I: Configured from console by tty17
Jun 11 09:37:13.286: %AUTOSMARTPORT-5-REMOVE: Device removed from interface GigabitEthernet1/0/6, executed BUF_SWITCH to remove the configuration
Jun 11 09:37:13.621: %SYS-5-CONFIG_I: Configured from console by tty17
Jun 11 09:37:13.669: %AUTOSMARTPORT-5-INSERT: Device Un-Classified Device detected on interface GigabitEthernet1/0/6, executed CISCO_LAST_RESORT_EVENT
Hope someone can give me a clue on what could be causing this.
Best regards
Isaac

I have gone further on investigating and the switch receives information about all the devs that are on the neighbour switch and takes actions according to it.
HX927438_SW43(config-if)#do sh macro auto monitor dev
Summary:
MAC_Address       Port_Id       Profile Name                        Device Name
==============    ==========    ===============================     =======================
40f4.ec75.1e01    Gi1/0/6       Cisco-Switch                        cisco WS-C2960S-24PS-L
0008.5d74.4176    Gi1/0/6       Un-Classified Device                Unknown Device
40f4.ec75.1e41    Gi1/0/6       Cisco-Device                        CISCO SYSTEMS
30f7.0d5c.b81f    Gi1/0/6       Un-Classified Device                Unknown Device
0006.f63c.ee04    Gi1/0/6       Cisco-Device                        CISCO SYSTEMS
===========================================================================
My Gi1/0/6 is Uplink to one other Auto Smarports device.
I have tried to stop macro auto processing on the neighbor switch but that doesn't help.
Someone could help on how to solve this - maybe some turn around? Could that be an IOS issue?
Best
Isaac

What is the maximum number of rows in version 3.5.3

I am using Numbers v3.5.3 in Yosemite.
I need to copy/paste from a .txt file 1,085,300 lines of information.
Numbers will only accept !65,000 lines.
Is there a limit by default? Can that be extended?
Thank you.

Hi Wayne - you have been very helpful; thank you.
I work at a film / tv post production facility. We use Outlook365 and the Sharepoint feature to share Word Docs and Excel Spreadsheets virtually. I use the Excel functionality in Sharepoint so that we can track media we copy to our StorNext SAN volumes as well as the multiple LTFS and Tar Per Shot LTO5s we write for both our clients and as internal data backups. Managing the media is beyond critical as TV and Feature studios require the utmost care of their OCF (original camera footage) and dailies / editorial media.
Of the many toolsets we use to edit and color shows and feature films is the AutoDesk platform (think Flame, Inferno, Smoke). The application toolset writes over 20TBs of data to our SAN volumes and the way it writes the data is unique to the application. If you tried to look at via a Mac Finder or Windows Explorer, the hex values in the filenames would not make sense. We cannot associate those hex names with actual human readable project names.
One of my engineers used the AutoDesk app to spit out a 1 million line plus text file with human readable names of every project, file type and file path.
What I am trying to do is suck all of that data into a spreadsheet that I can upload to Sharepoint (or paste directly into Sharepoint). When I try to copy/paste on my Mac Mini directly into a Sharepoint page, both Safari and Firefox go into a spinning beach ball of death. Time stops; photons of light are bent towards the event horizon; you get the picture.
Since Numbers won't accept more than 65,000 lines, I need a way to get that data into a spreadsheet.
I have downloaded LibreOffice and will give that a try.
Knowing what you do now, might you have any other suggestions?
Thank you again.
Scott

Maximum AA-ports NME-CUE version 7.0

Similar Messages

Maybe you are looking for