Maximum Distance for FCOE on Nexus 6004
Hi,
We have a fabric composed by 2 Nexus 6004. The links between the 2 Nx 6004 are configured with vE_ports.
What is the maximum length for the links between the 2 Nexus 6004 ?
Many thanks in advance.
Nicolas.
I found the following, which is most likely not up to date
Q. Is the Nexus 6004 capable of long distance FCoE and will this functionality work at FCS?
The Nexus 6004 hardware allows FCoE distances up to 100km with 10GbE interface, 30km with 40GbE interface between two Nexus 6004 devices. However at FCS, the FCoE distance will be limited to 300m. Future software release will provide CLI tuning options to support longer distance.
•300m FCoE at FCS (optical transceiver distance limitation)
10-km FCoE for 10 GE and 40 GE ports with global QoS policy (roadmap)
Similar Messages
-
I need to Integrate a paging system with VG router using ISDN BRI. the manufacture for the paging system told us to use NM-4B-U module in our cisco router and I need to know what is the maximum distance supported between the two devices.
Very nice.
We've already ordered the module. and we ordered two modules :)
The account manager will be very happy
About me, I evaluated you reply as extremely helpful but I did not check "Resolved my issue" because I have now new problem :) -
Nexus 6004 vs 6509 for Cores?
My organization is in the process of implementing two projects:
*Replacing our cores
*Upgrading our server access switches
Our current cores are dual WS-C6509's running in HSRP mode. We are upgrading them to new 6509's so we can implement VSS. They have not been installed yet, but we do have the equipment in our posession and mostly configured.
We are also in talks to purchase two Nexus 6004 chassis along with sixty 2232TM-E FEX's. It looks like this is going to happen soon. We use 4506's for our server access layer and are looking for the 6004/2000 Nexus platform to replace all of these 4506's.
What are the pro's and con's of skipping the 6509's and instead using the 6004/2232TM-E setup as our Core and Access layer?You can just use the 6000 and eliminate the 6500 altogether. I am deploying 6004 as layer-3 and also for FEXs and server connectivity. One thing to remember is that with the current Nexus-OS if you are using the 6ks as layer-3, you can only connect 24 FEXa to a pair of 6ks. If you are using them as layer-2 only then the number is 48.
The other thing you should know is that the 6ks are 40Gig only. So, in order to connect for example a FEX or another device to it using 10Gig, you need to purchase the special 40Gig to 10Gig cable. This cable has a 40gig interface and one side and 4 10gig on the other side. We get ours from Panduat and they work really well. These cables are not cheap. They cost is about $500 per cable.
If you need part number for the cable and you need more info let me know.
http://www.panduit.com/wcs/Satellite?c=Page&childpagename=Panduit_Global%2FPG_Layout&cid=1345564328975&packedargs=locale%3Den_us%26prod_cat_id%3D3%26prod_id%3D3&pagename=PG_Wrapper
HTH -
I am looking at replacing my MDS 9506 (2) with 4 nexus 6004.
FC will connect to the new 20 port UP cards on the nexus 6004
some info req.
Configurations simiilar to that of mDS
support for zoning
npiv support
what lic is required NPIV - FC
vsan
dcns
optics from MDS 9506 will work on nexus 6004
fcoe support - lic reqPlease look at
http://www.cisco.com/c/en/us/products/collateral/switches/nexus-6000-series-switches/datasheet-c78-732277.html
which contains the hardware features as well as the licenses.
It is easy to migrate a configuration from MDS to Nexus 6004.
Be aware, that there might be features, which are not available on Nexus, e.g. IVR.
Also, the native FC speed limitation is 8 Gbps !
Cisco SFP's from MDS should work ok in Nexus 6004
http://www.cisco.com/c/en/us/products/collateral/storage-networking/mds-9000-series-multilayer-switches/product_data_sheet09186a00801bc698.html -
Nexus 6004 TOR connectivity to Brocade DCX
Hi Experts,
I am facing an issues in our new data centre. We want to install Nexus 6004 in the TOR and connect the FC links back to the existing DCX?
I see from the datasheets that the 6004 now has native FC capability. Is it supported to set the 6004 to NPIV mode and connect as an Access gateway to the edge for the Brocade SAN?
Any advise appreciated as I really want to push CISCO at the TOR.
digduggoSee Figure 6-2 Converged Multi-hop FCoE Network Design Using FCoE NPV
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/operations/fcoe/513_n1_1/ops_fcoe/ops_fcoe_npv.html
You have to use NPV on N5k, there is no FC interop support on N5k, to connect to Brocade. -
What is the maximum distance between a time capsule and an airport express?
What is the maximum distance between a time capsule and an airport express?
You can only "extend" the signal one time, so you need to have the AirPort Express located approximately 1/2 to 2/3 of the distance from the Time Capsule to the area that needs more wireless coverage.
I doubt that this will help much since you have a very challenging setup. Wireless is really only for "same room" or "nearby rooms" around the corner.
To do this correctly you will need to use an Ethernet cable connection from the Time Capsule to the AirPort Express, which could then be located close to the xBox.
If it is not possible to run the Ethernet cable, you might look at a pair of Ethernet powerline adapters to send a "psuedo" Ethernet signal over the AC wiring in your home.
This will not be anywhere near the performance of a regular Ethernet cable, but it will likely be much better than wireless.
Since Ethernet over powerline (EOP) is somewhat unpredictable, you would want to have a very clear understanding of the store's return policy in case things don't work out as hoped. Any computer / electronics superstore will have a selection of powerline adapters to choose from. -
Nexus 6004 EIGRP Relationship between the two switches
Hi All,
I will try to explain this as best as I can. In our current TEST LAB we have a Pair of Cisco ASA5585x running in Active/Passive mode. We use a VRF transit to connect the 10 GB interface to a Pair of Cisco Nexus 6004 (L3) switches running vPC between them. Downstream we also have a pair of Cisco 9372 switches (L2) also running vPC between the two.
As of right now we have EIGRP neighbor relationship formed between the two N6K's and the ASA.
ASA
ciscoasa# sh eigrp neighbors
EIGRP-IPv4 neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
1 172.16.230.9 Te0/8.451 12 01:30:25 1 200 0 52
0 172.16.230.10 Te0/8.451 12 01:30:25 1 200 0 48
The ASA formed relationship with both N6K's
SWITCH1
Nexus6-1# sh ip eigrp neighbors vrf inside
IP-EIGRP neighbors for process 100 VRF Inside
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 172.16.8.3 Vlan680 11 01:28:28 1 50 0 45
1 172.16.230.10 Vlan451 13 01:28:28 1 50 0 46
2 172.16.230.11 Vlan451 10 01:28:00 4 50 0 13
Nexus6-1#
SWITCH2
Nexus6-2# sh ip eigrp neighbors vrf Inside
IP-EIGRP neighbors for process 100 VRF Inside
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
2 172.16.8.2 Vlan680 14 01:30:11 23 138 0 48
0 172.16.230.9 Vlan451 13 01:30:11 480 2880 0 50
1 172.16.230.11 Vlan451 13 01:29:48 1598 5000 0 13
Nexus6-2#
Both Nexus Switches formed EIGRP neighbors using the vPC Peer-Link. There is enough documentation out there that strongly suggest not to use vPC Peer-Links for EIGRP anything.
We do have additional interfaces available on the 6K's that we can use as a cross connect for EIGRP. What we are having trouble understanding how we can force EIGRP traffic over those ports?
Here is a complete Switch config:
Switch1
Nexus6-1# sh run
feature telnet
cfs eth distribute
feature eigrp
feature interface-vlan
feature lacp
feature vpc
feature lldp
vlan 1
vlan 451
name P2P_VRF_SVI
vlan 652
name Management
vlan 680
name Inside
vrf context Inside
vrf context management
ip route 0.0.0.0/0 172.16.52.1
vrf context peer-keepalive
vpc domain 99
role priority 1
peer-keepalive destination 10.200.50.2 source 10.200.50.1 vrf peer-keepalive
delay restore 120
interface Vlan1
interface Vlan451
description Inside p2p to ASA
no shutdown
vrf member Inside
ip address 172.16.230.9/29
ip router eigrp 100
no ip passive-interface eigrp 100
interface Vlan651
interface Vlan680
description Inside Network
no shutdown
vrf member Inside
ip address 172.16.8.2/22
ip router eigrp 100
interface port-channel99
switchport mode trunk
spanning-tree port type network
vpc peer-link
interface port-channel102
switchport mode trunk
vpc 102
interface Ethernet1/1
description vPC Peer Link 1.1
switchport mode trunk
speed auto
channel-group 99
interface Ethernet1/6
interface Ethernet1/7
description vPC Peer Link 1.7 to Nexus 9372 PRI
switchport mode trunk
speed auto
channel-group 102 mode active
interface Ethernet1/8
interface Ethernet1/9
interface Ethernet2/1
description vPC Peer Link 2.1
switchport mode trunk
speed auto
channel-group 99
interface Ethernet2/2
interface Ethernet2/7
description vPC Peer Link 2.1 to Nexus SEC
switchport mode trunk
speed auto
channel-group 102 mode active
interface Ethernet2/8
interface Ethernet8/1
description keep-alive peer-link to ALNSWI02
no switchport
vrf member peer-keepalive
ip address 10.200.50.1/30
interface Ethernet8/2
description Uplink to ASA
switchport mode trunk
interface Ethernet8/3
interface mgmt0
vrf member management
ip address 172.16.52.3/23
line console
line vty
boot kickstart bootflash:/n6000-uk9-kickstart.7.0.1.N1.1.bin
boot system bootflash:/n6000-uk9.7.0.1.N1.1.bin
router eigrp 100
passive-interface default
default-information originate
vrf Inside
autonomous-system 100
default-information originate
poap transit
Nexus6-1#
Nexus6-1# sh ip eigrp neighbors vrf inside
IP-EIGRP neighbors for process 100 VRF Inside
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 172.16.8.3 Vlan680 11 01:28:28 1 50 0 45
1 172.16.230.10 Vlan451 13 01:28:28 1 50 0 46
2 172.16.230.11 Vlan451 10 01:28:00 4 50 0 13
Nexus6-1#
Nexus6-1# sh ip eigrp topology vrf Inside
IP-EIGRP Topology Table for AS(100)/ID(172.16.8.2) VRF Inside
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 172.16.8.0/22, 1 successors, FD is 2816
via Connected, Vlan680
P 172.16.230.8/29, 1 successors, FD is 2816
via Connected, Vlan451
Nexus6-1# sh vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 99
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : primary
Number of vPCs configured : 1
Peer Gateway : Disabled
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Auto-recovery status : Disabled
vPC Peer-link status
id Port Status Active vlans
1 Po99 up 1,451,652,680
vPC status
id Port Status Consistency Reason Active vlans
102 Po102 up success success 1,451,652,6
80
Nexus6-1# sh spanning-tree
VLAN0001
Spanning tree enabled protocol rstp
Root ID Priority 32769
Address 1005.caf5.88ff
Cost 2
Port 4197 (port-channel102)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 8c60.4f2d.2ffc
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
Po99 Desg FWD 1 128.4194 (vPC peer-link) Network P2p
Po102 Root FWD 1 128.4197 (vPC) P2p
Eth8/2 Desg FWD 2 128.1026 P2p
Eth8/3 Desg FWD 2 128.1027 P2p
VLAN0451
Spanning tree enabled protocol rstp
Root ID Priority 33219
Address 8c60.4f2d.2ffc
This bridge is the root
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 33219 (priority 32768 sys-id-ext 451)
Address 8c60.4f2d.2ffc
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
Po99 Desg FWD 1 128.4194 (vPC peer-link) Network P2p
Po102 Desg FWD 1 128.4197 (vPC) P2p
Eth8/2 Desg FWD 2 128.1026 P2p
VLAN0652
Spanning tree enabled protocol rstp
Root ID Priority 33420
Address 1005.caf5.88ff
Cost 2
Port 4197 (port-channel102)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 33420 (priority 32768 sys-id-ext 652)
Address 8c60.4f2d.2ffc
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
Po99 Desg FWD 1 128.4194 (vPC peer-link) Network P2p
Po102 Root FWD 1 128.4197 (vPC) P2p
Eth8/2 Desg FWD 2 128.1026 P2p
VLAN0680
Spanning tree enabled protocol rstp
Root ID Priority 33448
Address 1005.caf5.88ff
Cost 2
Port 4197 (port-channel102)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 33448 (priority 32768 sys-id-ext 680)
Address 8c60.4f2d.2ffc
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
Po99 Desg FWD 1 128.4194 (vPC peer-link) Network P2p
Po102 Root FWD 1 128.4197 (vPC) P2p
Eth8/2 Desg FWD 2 128.1026 P2p
Nexus6-1#
Switch2
Nexus6-2# sh run
!Command: show running-config
!Time: Sat Feb 12 19:02:44 2011
version 7.0(1)N1(1)
hostname Nexus6-2
feature telnet
cfs eth distribute
feature eigrp
feature interface-vlan
feature lacp
feature vpc
feature lldp
vlan 1
vlan 451
name P2P_VRF_SVI
vlan 652
name Management
vlan 680
name Inside
vrf context Inside
vrf context P2P_Inside_VRF
vrf context management
ip route 0.0.0.0/0 172.16.52.1
vrf context peer-keepalive
vpc domain 99
role priority 2
peer-keepalive destination 10.200.50.1 source 10.200.50.2 vrf peer-keepalive
delay restore 120
interface Vlan1
interface Vlan451
description Inside p2p to ASA
no shutdown
vrf member Inside
ip address 172.16.230.10/29
ip router eigrp 100
no ip passive-interface eigrp 100
interface Vlan680
description Inside Network
no shutdown
vrf member Inside
ip address 172.16.8.3/22
ip router eigrp 100
interface port-channel99
switchport mode trunk
spanning-tree port type network
vpc peer-link
interface port-channel102
switchport mode trunk
vpc 102
interface Ethernet1/1
description vPC Peer Link 1.1
switchport mode trunk
speed auto
channel-group 99
interface Ethernet1/2
interface Ethernet1/6
interface Ethernet1/7
description vPC Link 1.7 to Nexus 9372 SEC
switchport mode trunk
speed auto
channel-group 102 mode active
interface Ethernet1/8
interface Ethernet1/12
interface Ethernet2/1
description vPC Peer Link 2.1
switchport mode trunk
speed auto
channel-group 99
interface Ethernet2/2
interface Ethernet2/6
interface Ethernet2/7
description vPC Link 2.1 to Nexus PRI
switchport mode trunk
speed auto
channel-group 102 mode active
interface Ethernet2/8
interface Ethernet2/12
interface Ethernet8/1
description keep-alive peer-link to ALNSWI01
no switchport
vrf member peer-keepalive
ip address 10.200.50.2/30
interface Ethernet8/2
description Uplink to ASA
switchport mode trunk
switchport trunk allowed vlan 1,451,652,680
interface Ethernet8/3
interface Ethernet8/20
interface mgmt0
vrf member management
ip address 172.16.52.4/23
line console
line vty
boot kickstart bootflash:/n6000-uk9-kickstart.7.0.1.N1.1.bin
boot system bootflash:/n6000-uk9.7.0.1.N1.1.bin
router eigrp 100
vrf Inside
autonomous-system 100
default-information originate
poap transit
logging logfile messages 6
Nexus6-2#
Nexus6-2#
Nexus6-2# sh ip eigrp neighbors vrf Inside
IP-EIGRP neighbors for process 100 VRF Inside
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
2 172.16.8.2 Vlan680 14 01:30:11 23 138 0 48
0 172.16.230.9 Vlan451 13 01:30:11 480 2880 0 50
1 172.16.230.11 Vlan451 13 01:29:48 1598 5000 0 13
Nexus6-2#
Nexus6-2# sh ip eigrp topology vrf Inside
IP-EIGRP Topology Table for AS(100)/ID(172.16.8.3) VRF Inside
Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,
r - reply Status, s - sia Status
P 172.16.8.0/22, 1 successors, FD is 2816
via Connected, Vlan680
P 172.16.230.8/29, 1 successors, FD is 2816
via Connected, Vlan451
Nexus6-2#
Nexus6-2#
Nexus6-2# sh vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id : 99
Peer status : peer adjacency formed ok
vPC keep-alive status : peer is alive
Configuration consistency status : success
Per-vlan consistency status : success
Type-2 consistency status : success
vPC role : secondary
Number of vPCs configured : 1
Peer Gateway : Disabled
Dual-active excluded VLANs : -
Graceful Consistency Check : Enabled
Auto-recovery status : Disabled
vPC Peer-link status
id Port Status Active vlans
1 Po99 up 1,451,652,680
vPC status
id Port Status Consistency Reason Active vlans
102 Po102 up success success 1,451,652,6
80
Nexus6-2#
Nexus6-2#
Nexus6-2# sh spanning-tree
VLAN0001
Spanning tree enabled protocol rstp
Root ID Priority 32769
Address 1005.caf5.88ff
Cost 3
Port 4194 (port-channel99)
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Bridge ID Priority 32769 (priority 32768 sys-id-ext 1)
Address 8c60.4f2d.777c
Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec
Interface Role Sts Cost Prio.Nbr Type
Po99 Root FWD 1 128.4194 (vPC peer-link) Network P2p
Po102 Root FWD 1 128.4197 (vPC) P2p
Eth8/2 Desg FWD 2 128.1026 P2p
Eth8/3 Desg FWD 2 128.1027 P2p
VLAN0451
Spanning tree enabled protocol rstp
Root ID Priority 33219
Address 8cJon,
Are you ready for the mass confusion?
when Looking at the ASA EIGRP neighbors output here is what I see.
ASA# sh eigrp neighbors
EIGRP-IPv4 neighbors for process 100
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
3 172.16.230.1 Te0/8.450 13 16:45:14 1 200 0 64
2 172.16.230.2 Te0/8.450 11 16:45:14 1 200 0 84
1 172.16.230.10 Te0/8.451 11 16:45:20 1 200 0 178
0 172.16.230.9 Te0/8.451 13 16:45:20 1 200 0 148
For simplicity sake lets just concetrate on Interface TenGigabit0/8.451 which is the SVI on the Nexus switch that is VLAN451
From the Nexus Switch 6004 that is directly connected to the ASA here is what I see
SWI01# sh ip eigrp neighbors vrf Inside
IP-EIGRP neighbors for process 100 VRF Inside
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 172.16.8.3 Vlan680 10 17:04:30 54 324 0 177
1 172.16.230.10 Vlan451 11 16:59:10 819 4914 0 178
2 172.16.230.11 Vlan451 14 16:53:48 24 144 0 20
The Inside VRF that is tied to both SVI's on the Switch vlans 451 and 680 is in EIGRP 100 on the switch
SWI01# sh run int vlan 451
interface Vlan451
description Inside p2p to ASA
no shutdown
vrf member Inside
ip address 172.16.230.9/29
ip router eigrp 100
no ip passive-interface eigrp 100
SWI01# sh run int vlan 680
interface Vlan680
description Inside Network
no shutdown
vrf member Inside
ip address 172.16.8.2/22
ip router eigrp 100
hsrp 1
authentication text test
preempt
priority 250
ip 172.16.8.1
so you with me so far?
If you are you have noticed that on the ASA neighbors the ASA sees 172.16.230.11 as a neighbor which is the Secondary Nexus SW. That is becauise they all share the same subnet.
172.16.230.8/29
Brakedown:
PRI Nexus 6004 - 172.16.230.9
SEC NEXUS 6004 - 172.16.230.10
PRI ASA 5585x - 172.16.230.11
SEC ASA 5585x - 172.16.230.12
Because the ASA EIGRP network is a /29 it learns the Secondary Nexus via the Primary Nexus.
I am not sure that the link we created between the two Nexus Switches is doing anything but consuming ports right now.
SWI01# sh run int ethernet 8/9
interface Ethernet8/9
description EIGRP PORT to Secondary Nexus
switchport mode trunk
switchport trunk allowed vlan 450-451
SWI02# sh run int ethernet 8/9
interface Ethernet8/9
description EIGRP PORT to Primary Nexus
switchport mode trunk
switchport trunk allowed vlan 450-451
So the SVI's that go up to the ASA for inspection are 450 and 451. The network SVI's are 600 and 680 all of them live on the switch, and 680, and 600 are extended over the peer links down to the 9372's.
I think that we are breaking the golden rule of vPC BUT.. I am not 100% sure. Some of the documents read that we should not be allowing network vlans over peer links, but then how do you extend the vlans down to the leaf switch?
This is giving me nightmares at the moment…
does this make sense? -
Max. install distance for Speaker Track 60 Cameras to SX80 CODEC
Just integrated a SX80 / Speaker Track 60 system and the cameras are not providing video signal, (selfview) to the integrated displays.
Question: What's the maximum length a Non-Active HDMI cable can be, between the PHD 60 camera(s) and the SX80 CODEC?
Will Active HDMI cables help carry the camera's video signal to distances of 50' or greater?I don't know about the SpeakerTrack 60, but I know the PrecisionHD cameras, the maximum was 50 meters (50 feet) with a category 2 good quality HDMI cable. I looked through the SpeakerTrack documentation, but didn't find any mention of maximum length for the HDMI cable, however I did find the below searching online.
Extending the Precision60 and SpeakerTrack60 Cameras -
MGBSX1 and maximum distance on CISCO SG300-10SFP-K9-EU
Hi,
reading this page: http://www.cisco.com/c/en/us/products/collateral/switches/small-business-smart-switches/data_sheet_c78-610061.html I noticed that there is written that the MGBSX1 maximum distance on SG300 or SF300 Series is 300 meters.
On the same page there is written that the MGBSX1 support up to 550 m. What is the right value? The distance depends on the switch?
Thank you.
Best regards,
Giovanni Alai
Nextmedia s.r.l.Hi,
MGBSX1 over multimode cable for 1000BASE speed it supports from 220 to 550 meters(Based on fiber diameter and bandwidth).
regards
Moorthy -
Cisco Nexus 6004 | Fibre Tx and Rx Levels
Hi All,
On the Nexus 6004 series, does anybody know how to see the light levels for the optics.
I am using the command: show interface ethernet 2/5/4 transceiver details which outputs:
Ethernet2/5/4
transceiver is present
type is QSFP-40G-CSR4
name is CISCO
part number is AFBR-79EEPZ-CS2
revision is 02
serial number is XXXXXXXX
nominal bitrate is 10300 MBit/sec
Link length supported for 50/125um OM3 fiber is 300 m
Link length supported for 50/125um OM2 fiber is 82 m
cisco id is --
cisco extended id number is 16
SFP Detail Diagnostics Information (internal calibration)
Current Alarms Warnings
Measurement High Low High Low
Temperature 47.63 C 75.00 C -5.00 C 70.00 C 0.00 C
Voltage 3.32 V 3.63 V 2.97 V 3.46 V 3.09 V
Current 0.00 mA 0.00 mA 0.00 mA 0.00 mA 0.00 mA
Tx Power N/A N/A N/A N/A N/A
Rx Power N/A N/A N/A N/A N/A
Note: ++ high-alarm; + high-warning; -- low-alarm; - low-warning
Is it a case that the SFP's in this instance do not support the light level information? the controller, optics or wdm commands are not available on the Nexus.
Thanks all for your support.Hi Marvin,
The System version: 6.0(2)N1(2)
Software
BIOS: version 2.6.0
loader: version N/A
kickstart: version 6.0(2)N2(2)
system: version 6.0(2)N2(2)
Power Sequencer Firmware:
Module 0: version v5.0
Module 1: version v2.0
Module 2: version v2.0
Module 3: version v2.0
Module 4: version v2.0
Fabric Power Sequencer Firmware: Module 0: version v3.0
Microcontroller Firmware: version v1.1.0.3
QSFP Microcontroller Firmware:
Module 1: v1.3.0.0
Module 2: v1.3.0.0
Module 3: v1.3.0.0
Module 4: v1.3.0.0 -
Set Maximum size for a subpanel created with splitter bars in LV8
Does anyone know how to set the Maximum size for a subpanel created with asplitter bar? If I show one cluster in the subpanel and use the scroll bar to scroll, I can see more (blank) area than I want. I just want the user to be able to scroll a cluster within a subpanel while the cluster is larger than the view area of the subpanel. I don't want to let the user scroll outside the cluster.
Ravi BeniwalI apologize for the mixup in terminology. Please read Pane wherever the word Subpanel was used.
Please see the attached VI for a description of my problem.
I would really appreciate any help with this.
Ravi Beniwal
Attachments:
Pane Scrolling Problem.vi 10 KB -
I have FF 34 but this problem has been there for a lot of earlier versions. On many webpages there are pictures that cover my whole screen, and I want to set maximum size for showing images on webpages.
I ONLY wanr to change the maximum size of the images, AND IAM NOT asking about how to zoom the webpage.Do you want to hide large images or merely make them smaller by setting a max-width and max-height?
You would probably have to use JavaScript (bookmarklet) to achieve this reliably.
There are bookmarklets to make large images fit in the window to avoid a horizontal scroll bar
You can try this code in the <b>userContent.css</b> file (adjust the max-width accordingly).
*http://kb.mozillazine.org/userContent.css
<pre><nowiki>img { max-width: 1024px !important; height: auto !important; }</nowiki></pre>
The customization files userChrome.css (user interface) and userContent.css (websites) are located in the <b>chrome</b> folder in the Firefox profile folder.
*http://kb.mozillazine.org/Editing_configuration
*Create the chrome folder (lowercase) in the <xxxxxxxx>.default profile folder if this folder doesn't exist
*Use a plain text editor like Notepad to create a (new) userContent.css file in the chrome folder (file name is case sensitive)
*Paste the code in the userContent.css file in the editor window
*Make sure that you select "All files" and not "Text files" when you save the file via "Save file as" in the text editor as userContent.css.<br>Otherwise Windows may add a hidden .txt file extension and you end up with a not working userContent.css.txt file -
Maximum resolution for external monitor on a B570e
hi,
i've just bought a Lenovo B570e in which i've plugged a Philips 221 V. That has a nominal resolution of 1920 x 1080.
However, when I try and setup its resolution, whether it's through the native windows graphic manager or the intel graphic manager, to 1920 x 1080, nothing is displayed. I need to lower the resolution down to 1680 x 1050 in order for the lenovo to display anything on the external monitor.
am i missing something, or is 1680 x 1050 the maximum resolution for dual display?
thank you
J.thanks for the help.
-
Maximum size for an HttpRequest? Set Content-Length?
Hi, I'm managing to get small strings sent from my applet to my servlet, but when I try anything bigger, I get problems. Oddly enough, the larger object can get sent to my applet from my servlet without any issues.
Can anyone tell me if there is a maximum size for sending responses?
Or, if I have to set the content-length property in my applet before I send my data, how do I get the size of my object so I can set it?
thanks for any advice any of you might haveThanks for the pointers.
BalusC, at first I was trying to write my object without sending it through a byteStream first (hence the q) :), tried it that way too and wouldn't work.
I finally figured out that it wasn't the code that was the problem, but it was an upload issue (server specific). Have changed the code to sending one line of data at a time since I was converting my object to an output file in the servlet anyway. Not the best solution but it works :)
Thanks again -
Hi,
My places.sqlite file size is 30,720 KB have I reached the maximum size, is there even a maximum size for this.
Suddenly the visited links are no longer changing font color, as I am preparing for an exam I need visited questions to change color, to keep track of questions that I have finished. But if I delete a few days of history then again,a few more visited links change color then again it stops, so it seems something is getting full and not able to accommodate any more? Why are my visited links no longer changing color after a certain number of visits? I do have a back up of the places.sqlite file. So I have tried everything from deleting the profile, uninstalling reinstalling, creating a new profile, then copy pasting places.sqlite etc, but as mentioned after a few visits, visited links no longer change color, if I delete a few days of history then again a few visits will again change color and then stop again, so what should I increase so that my visited links quota is increased, I have also tried tweaking about:config and it has had no result. Although I was not really confident that increasing brower.history_max _pages (don't remember exact name, but I am sure you get the idea) is going to help.
Seems as though my visited links change color, quota is full and only if I delete a few days of history will I get a few more visited links to change color. Can somebody shed some light? As mentioned my places.sqlite file size is 30,720 KB so I think perhaps this has something to do with this? Would really appreciate if someone could help. Thank you.There is no maximum for the places.sqlite database and other SQLite database files like I wrote above.<br />
All SQLite database file have fixed minimum sizes and if they run out of space they are automatically increased in size with a specific chunk size. For places.sqlite this is 10 MB for the minimum and for the chunk.
*Bug 581606 - Avoid sqlite fragmentation via SQLITE_FCNTL_CHUNK_SIZE
Maybe you are looking for
-
Trying to link to a specified frame
Hi first of all sorry for my english ;-) i konw that its possible to link from a html link, via javscript, to a specified frame in a swf, but im looking since yesterday and cannot find something to help me ( yes i found something like this but to com
-
UTL_FILE - File Size limit does not exceed 32990 bytes
Hi, We are using UTL_FILE package of oracle for writing data into a file.We are using "UTL_FILE.FOPEN" function to open the file in the write mode and "UTL_FILE.PUT" function to write data into it. We have specified the max size of the record as 3276
-
Does only Adobre Reader "reads" the fields of a PDF when created with Acrobat?
I created a PDF with several fields and exported it. Then I tried to open it with Firefox and the fields didn't appear. But it works OK with Adobe Acrobat. Does only Adobre Reader "reads" the fields of a PDF when created with Acrobat?
-
Problem 6500 Classic. Camera & Flash not Syncroniz...
On my 6500 Classic 1 week old i have a problem,in camera mode the flash does not seem to be syncronized with the camera, once the image is captured the image is dark apart from a small strip at the right side of the screen. I also cannot activtae nig
-
i am getting multiple errors when trying to insert data into a table through pl/sql declaration here are the errors: --Procedure to insert the values into section table(ex1.sql) declare v_section %type; begin v_section.SECTIONNO:=&no; v_section. DESC