Maximum hard drive size for HP Pavilion Elite e2980t? I put in a 3TB, but it shows up as 800GB

I installed a 3TB drive, but it shows up in the bios as 800GB. What is the maximum supported size?
I suspect that the HP Pavilion Elite e2980t cannot accept more than an 800 GB drive. This is consistent with the product selection choices that are available to purchasers. 
Can anyone confirm?
Are there a set of drivers I can install that would work around this limitation?

Hi:
If you are using the drive as a boot drive, your PC probably does not have a UEFI BIOS, so it can't recognize all 3 TB.
If you are using it as a data drive, go into the Windows disk management tool, format the drive GPT, and windows should be able to see and use all 3 TB.
Please see this white paper regarding UEFI & GPT.
While this applies to business desktops it is also relevant to consumer desktops as well.
http://h20565.www2.hp.com/portal/site/hpsc/templat​e.BINARYPORTLET/public/kb/docDisplay/resource.proc​...

Similar Messages

  • Can I use a usb external hard drive larger than 2TB?  I have tried to use a 3TB but it shows up as 800GB.

    Can I use a usb external hard drive larger than 2TB?  I have tried to use a 3TB but it shows up as 800GB.  Even tred to reformat in disk utility but only shows as 800 gb as well.  It is a Seagate 3TB harddrive and enclosure.  Nothing on the Seagate site about it other than it says Mac os through 10.6 is supported  for larger than 2TB (might be old).

    You might have better luck in the Snow Leopard community. I'll ask the hosts to relocate your post.
    10.6 Snow Leopard

  • Maximum hard drive size for 350 MHz slot loading?

    Hello,
    What is the maximum hard drive size for a 350 MHz slot loading imac?
    I am aware of a 128 GB limit on imacs. Does the 128 GB hard drive limit apply to all imac CRTs or just the earlier models?
    Here are the specs of my imac:
    Blueberry 350 MHz
    Slot loading CD-ROM drive,
    6 GB hard drive
    Is the maximum hard drive size limit of 127GB apply to this particular model?
    Thanks

    Yes, the last CRT iMac was in 2001. The first machines with built-in greater than 127 GB support were released in June 2002, as this article explains:
    http://docs.info.apple.com/article.html?artnum=86178
    So all CRT iMacs have that limiation.
    http://support.apple.com/specs/imac/
    The 8 GB limit is explained here:
    http://docs.info.apple.com/article.html?artnum=106235

  • Maximum hard drive size for upgrading a dv6375ea?

    Hello to all,
      My hard drive began to make noises and since it is past warranty, I will upgrade it. When I had bought the laptop I had chatted with a HP personnel on these support pages, and he/she had told me that the maximum size that the bios allowed was 120 gb. That is the original hard drive size!
      Has anyone upgraded their hard drive or does anybody know of a technical value that I should try?
    Thanks for your time,

    You can install as large a drive as you can find as long as it is SATA and 2.5" wide and 9.5 mm thick. SATA drives have no BIOS size limit. However, some have occasionally reported issues with 500 gig drives and 7200 rpm drives. I can therefore tell you with 100% certainty you can install a 320 gig 5400 rpm drive in your laptop. My favorite website for laptop hard drives is newegg.com. Don't buy from HP parts; it will cost way too much. You should be able to find the drive I mention for around $80 and laptop drives are also sold at Best Buy, Frys and similar stores.

  • What is the maximum hard drive size for Imac 8,2, what is the maximum hard drive size for Imac 8,2

    Am wondering what is the maximum hard drive one can put into this computer. I think it's a 3TB but I read somewhere the drive needs a jumper to bring it back to 3mb level cache. Can anyone confirm these details please? I currently have a 320GB drive installed.

    Hi Robbie,
    I found no iMac 8,2, do you mean iMac 8,1 ???
    There is no practical limit to the size, the biggest ones made will work fine... assuming the all important SATA 3 Gb/s speed, WD drives use a jumper on pins 5&6 to slow it from 6 Gb/s to 3 Gb/s.
    Some drives do it automatically...
    http://eshop.macsales.com/item/HGST/0F14681/
    And some do not step down properly at all.

  • Maximum hard drive size for HP HPE-180t

    Is there a way to have the entire space of a 4TB SATA III (6Gb/s) drive show up in Windows 7 x64 running on an HPE 180t?  I installed one such hard drive on my HPE-180t, and the BIOS only saw 2TB of space, and the drive did not show up in Windows.  HP Diagnostics tools (run before Windows starts) reported the following error "communication with device failed".   The motherboard and bios info is shown below.  SATA mode is set to RAID.   The hard drive itself passes all the SMART tests in BIOS and seems to function fine. 
    There are two separate problems.   The communication error above, which needs to be solved first, and the "only 2TB showing in BIOS" problem.   Can the 2TB problem be addressed with another BIOS on this motherboard or some BIOS setting on the existing BIOS?  If so, what is the BIOS and/or settings?
    I looked through HP online support today (including google searches on the HP support forums) and did not see the answer to these questions/problems.
    System Board  
       Manufacturer PEGATRON CORPORATION 
       Product TRUCKEE
       Chipset Intel X58
       Southbridge Intel ICH10R
    BIOS
       Vendor American Megatrends Inc.
       Release Date 09/17/2010
       BIOS Version String 5.29
       ROM Size 1.00 MB

    Hi,
    You may want to read this and format HDD before the installation:
       http://msdn.microsoft.com/en-us/windows/hardware/gg463525.aspx
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Maximum Hard Drive Size for Mac Pro OS X 10.6.4

    I would like to install a backup drive in my Mac Pro. What is the largest drive I can install?
    A 1.0T would work but a 2.0T would be better.
    When I bought my Mac Pro in Oct 2008 it stated I could have up to 4.0T of drive space. Does that mean I am limited to 1.0T drives? I have since upgraded to Snow Leopard OS X 10.6.4. Will it recognize 2.0T drives?
    The new drive will be used for backup only. Any recommendations?

    A quick look for reviews shows the WD 2TB Black Caviar on numerous sites last October. And before that they had RE3 and RE4 and Green variety.
    Latest review of all the 1TB drive offerings.
    http://techreport.com/articles.x/19330
    Newegg offering Western Digital's 2TB Caviar Green hard drive for a juicy $99.99 with free shipping.
    http://techreport.com/discussions.x/19373
    And Seagate hopes to be the first with 3TB later this year.
    They already have one in USB2 case now.
    http://techreport.com/discussions.x/19177
    Best bet, check AccelerateYourMac web site drive upgrade database, check vendor for drives and their own knowledge base too.
    WD: http://www.wdc.com/en/products/productcatalog.asp

  • Does anyone know the maximum hard drive size for a 2007 Macbook Pro (A1226)?

    I have a 2007 Macbook Pro (A1226). Is there a limit to the sized hard drive that can be installed? If so, what is the largest hard drive I can put into it? I have a 500GB HD that I upgraded to from the 320 GB that was in it when I bought it. I'm now trying to install a 1 TB or 750 GB drive, but after cloning with 'Carbon Copy Cloner' and installing it, I get the "?-folder" flashing when I start up. I'm pretty confident in CCC because if I use it to clone to another 500GB HD, it works fine. The problem only occurs when I try to use larger drives. Is 500GB the largest HD I can use in this machine? If so, can anyone point me to a spec sheet so I can be sure the next Macbook I buy can be expanded to suit me.
    Thanks in advance.
    Brian

    You said:  "I've never tried the restore function in disk utility. Would that be the same as cloning the drive?
    YES!  See the my old instructions below.  What you might try after step 5 is to restart you MBP holding down the Option key.  Select the new HDD icon and see if it boots.  This way you will know that the new HDD is operable.
    Ciao.
    INSTALLING A NEW HDD IN A MB
    1. Make certain that you have backed up all of your important data.
    2. You will need a HDD enclosure.  One with a USB connection will do.  A 9 pin Firewire is better.
    3. Install your new drive in the enclosure and connect it to your MBP.
    4. Open DISK UTILITY>ERASE.  From the left hand column drag the new drive into the 'Name' field.  Make sure that the format is 'Mac OS Extended (Journaled)'.  Click on the 'Erase' button.
    5. Click on the 'Restore' button (on top).  Drag the old drive into the 'Source' field and the new drive into the 'Destination'  field.  Click on the 'Restore' button on the bottom right hand corner.
      Depending upon the amount of data you are transferring, this may take a couple hours or more.  A Firewire will speed up the transfer.  This will result in both drives having identical information on them.
    6. After the data transfer has completed, you may swap the drives.  Start the MBP and you have finished the installation.  The initial boot may take a bit longer than you are accustomed to, but that is normal.
    7. When you are satisfied that the new hard drive if functioning properly, you can erase the old drive and use it for any needs that you may have.

  • Maximum hard drive size for G5

    I have a Power Mac G5 2.7 I purchased in June '05. The system drive is 240 gigs. What is the largest drive I can put into the 2nd SATA slot?
    Thank you.

    Hello! A 750gb drive is workable. I don't see a lot of drives larger than that. Look at THESE.Tom

  • What is the maximum hard drive size can I install into my MacBook Pro 15 "late 2008 ?

    Hello community, I play with the thought in my MacBook Pro 15 "late 2008 equipped with an SSD hard drive. What is the maximum hard drive size can I install? Thank you in advance
    Dirk

    mende1, greetings:
    mende1 wrote:
    I don't recommend you to install a hard drive bigger than 2 TB if you are going to install Windows in Boot Camp or you may have problems
    The largest 2.5" SATA HDDs of 9.5 mm thickness that I am aware of are 1 TB in capacity.  There is a 12.5 mm thick  HDD that will fit some MBPs.  But I have not seen any of larger capacity. 
    Are there now 2 TB HDDs available for MBPs?    If so, I am interested.
    Ciao.
    Both OWC and Crucial have SSDs of about 1 TB capacity.
    Message was edited by: OGELTHORPE

  • UCS C series maximum hard drive size

    Looking for info on the maximum hard drive size support on teh UCS C series.  I have a C200M2 that I added a 4TB drive, I have updated the server to the latest firmware and BIOS however the server shows the drive size is 2TB.

    Hi!  and welcome to the community mate!
    Here is the table that shows the supported disk's PID for the C200 server:
    http://www.cisco.com/c/dam/en/us/products/collateral/servers-unified-computing/ucs-c-series-rack-servers/c200m2_sff_specsheet.pdf
    If you successfully installed ONE HDD of 4GB and made it work, you were lucky cause I don't see any disk with that size, I have not even seen a disk of that size for UCS yet.
    I am wondering if perhaps you installed 4 disks of 1TB and configured them in RAID 1 which would explain the reason for the size to go down to half of the capacity of the array as RAID 1 is a mirror.
    Let me know if I misunderstood you.
    Rate ALL helpful answers.
    -Kenny

  • T400 maximum hard drive size supported by BIOS.

    Does anyone know what the maximum hard drive size supported by the BIOS for a T400?
    Solved!
    Go to Solution.

    it doesn't exist yet. You can use any sata hdd with 2.5 inch form factor and 9.5 mm thickness. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • O.S. / Hard Drive Size for NIO Server/Client's load testing...

    Hi All
    I am currently load testing a NIO Server/Client's to see what would be the maximum number of connections that could reached, using the following PC: P4, 3GHz, 1GB RAM, Windows XP, SP2, 110 GB Hard Drive.
    However, I would like to test the Server/Client performance on different OS's:
    Which would be the best possible option from the following:
    1. Partition my current drive, (using e.g. Partition Magic), to e.g.
    - Win XP: 90 GB
    - Win Server 2000: 10 GB
    - Linux: 5 GB
    - Shared/Data: 5 GB
    2. Install a separate Hard drive with the different hard drives
    3. Use a disk caddie, to swap in/out test hard drives.
    4. Any thing else?
    - Would the Operating System's hard drive size affect the Server/Client's performance, e.g. affecting the number of connections, number of File Handles, the virtual memory, etc.?
    Many Thanks,
    Matt

    You can use a partition on the same HDD or use a second HDD, disk caddie well if its a direct IDE or SCSI. If its usb no it will be too slow, may be if you have a fire-wire but I still don't recommend it.
    Be careful if you don't have any experience installing Linux you may do multiple partitions on you disk without knowing, because Linux ext partitions are not visible to windows.
    Recommended disk size for fedora is 10 GB. This is the amount of data that will be created on you HDD when you do a full installation.

  • Maximum hard drive size in iMac

    I have a 2.0Ghz Alum iMac with a 250Gb hard drive in it and I was planning on putting a 1Tb 7200rpm 32mb cache drive in, in the next week or so. I believe that I shouldn't have any problems doing this, but I heard there might be a limit on the model I have. I have gone over the user guide and the tech specs and it doesn't say anything other than the iMac could have been configured by Apple to house a 500Gb drive and the only ones that Apple would put a Tb drive in was the 24" which makes me question if my iMac could handle the larger drive.

    a brody wrote:
    Actually upgrading the new iMac's hard drive is much more difficult. There about 24 screws you have to deal with and disassemble the entire machine to get at it. I've seen instructions online, and it is not child's play.
    I sorry to hear that. I'm probably going to buy a new iMac this weekend. What about memory upgrades? Are they fairly easy to do? I upgraded the memory in my MB without any problem. I guess I'm going to have to try to find the online iMac hard drive upgrade procedure to see how hard that is. I've never had a PC that I didn't upgrade the hard drives at least once. If the iMac is that big of a deal, I guess the best approach is to buy the biggest drive option up front.

  • The maximum acceptable hard drive size for hp hdx x16t-1200 cto ?

    my laptop is hp hdx x16t-1200 cto
    i want to know the maximum size of hard disk i can install in it (1TB or 750GB or 500 GB) ?
    This question was solved.
    View Solution.

    Hi,
    That means you can use up to 1TB (currently on the market, remember buy the 9.5mm one). These are how to do & tips:
      http://computershopper.com/laptops/howto/replace-your-laptop-s-hard-drive
      http://reviews.cnet.com/4520-11379_7-6445033-1.html
      http://www.cnet.com.au/upgrade-your-laptops-hard-drive-339298932.htm
    Good luck.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Maybe you are looking for

  • Black ink cartridge will not work even though new. HP3520 Deskjet

    I have changed to a new HP black catridge (364) and done different procedures for cleaning etc. Still no black print.

  • Server Exception when using JDBC to Connect with SAP

    Hello, I am trying to connect to a view in an external database using JDBC. When I run the TestJDBC Tool, I get the following server exception: com.microsoft.sqlserver.jdbc.SQLServerException: ?? ?? '<view_name>'?(?) ???????.     at com.microsoft.sql

  • Flash Quiz not calculating totals correctly at the end

    Hi, I am working on a Flash XML quiz, that can be found on this tutorial http://www.permadi.com/tutorial/flashMXQuiz/index3.html I have it just about working except at the end on the summary screen, the application is supposed to calculate the number

  • Format phone numbers

    I upgraded my 3G to a 4S. When all my contacts were imported into my new phone, I noticed that the phone numbers were not formatted properly, they looked like one big number, eg. "1231234567".  Is there a way to format all of my numbers properly (eg.

  • Attempting to clone MAC address, cannot save changes.

    Hello. I am attempting to use the MAC address cloning feature on my Linksys e2000 router. When I check "Enabled" and then attempt to save settings I receive "The values you entered are invalid. Please try again." I also receive this message if I sele