Maxium calls on Analog devices CCM v.7

I know this is probably a silly question but I would like to verify. Devices such as ATAs and VG248s that converts calls to analog, I've notice have only maximum call of 2. Is there a way around this or another way I have analog maximum calls set to 4?

The help document for the directory number settings page says:
"The default specifies 4. If the phone does not allow multiple calls for each line, the default specifies 2."
Analog devices do not support multiple calls per line. There is no way around this limitation to my knowledge.
Hope this helps.
Brandon

Similar Messages

Activate a call forward with a Third-party SIP Device or with a analog device

Hi,
In a CUCMv9, how i can activate a call forward (all, busy, no anwser...) with Third-party SIP Device or with a analog device connected to a fxs?
I want to activate a call forward like a Alcatel or Aastra PBX with a code.
For exemple, i pick up the phone, with the code *95 followed by the destination number and hangs up the phone. And use the #95 for désactivate this call forward.
It's possible?
Thanks.

No codes for 3rd party SIP phones, no way to do it. Or for that matter, not even for Cisco Phones, other than CFA.
Anything besides CFA needs to be done via CCMadmin or CCMuser for any kind of phone.
For FXS that's only doable if you're running SCCP
http://www.cisco.com/en/US/partner/docs/ios/voice/fxs/configuration/guide/fxssccpsplmft.html
HTH
java
if this helps, please rate
www.cisco.com/go/pdihelpdesk

TS3510 I have 3 different apple devices using the same Apple ID and would like to use FaceTime to call from one device to the other. Do I need a different Apple ID for one of the devices in order to do that?

I have 3 different apple devices (iPod Touch, iPad and MacBook Pro) using the same Apple ID and would like to use FaceTime to call from one device to the other. Do I need a different Apple ID for one of the devices in order to do that?

I found this on a related question in the Community:
Yes you can do it. I do it with 4 different devices all using the same Apple ID.
You need to associate different email addresses for each device in order to use those email addresses as the "contact at" email address. The reason the calls are dropping on you now is that what you are trying to do is like calling yourself on your own phone.
You can also create new iCloud accounts on each device simply to use for FaceTime, but I'm guessing that the users of the other two devices have their own email addresses which will make this work for you quite easily.
Take a look at this for more information.
The seems to go against what Gail said and the issue you raised about buying dup apps was my first concern. If this other post is correct, how to I set a different "contact at" in the iPod Touch?
Goose

If i used the same apple id and email to set up both my ipad and ipod what can i do to be able to use face time to call from one device to the other

if i used the same apple id and email to set up both my ipad and ipod what can i do to be able to use face time to call from one device to the other

They can share an Apple ID, but each device must use a different email address when setting up FaceTime. Create a gmail email (or hotmail, or ...) address and use that on one of the devices when you setup FaceTime.
You don't actually have to use the 'new' email address, it is probably just used as an index to reference the correct device when initiating a call via the FaceTime server.

TS1702 I have an iphone and my 2 children have ipods. all 3 on the same apple id. when one of their ipods gets a face time call , all 3 devices ring. i dont want to get these face time calls on my iphone or the other ipod . what is the solution to this

i have an iphone and my 2 children have ipods. all 3 on the same apple id. when one ipod gets a facetime call, all 3 devices ring. how do i prevent all three devices getting the facetime call as it is intended for only one of the ipods?

You can all have independent AppleIDs for iCloud or iMessage etc, but share the same one for iTunes Store / AppStore purchases.

Can I switch a Factime call from one device to another?

I would like to know if there is a way to pick up a Facetime call on one device and then switch it mid-call to another device, in the same way one is able to put down one extension and pick up another in mid-call to transfer it to another handset on a landline?
Thanks!

Do you mean Re- download...?
If so, see here... Download Past Purchases > http://support.apple.com/kb/HT2519

Apple recently merged all my devices so that if I miss messages or facetime calls on one device, they get forwarded to my other devices. how do I UNDO this so this no longer happens?

Apple recently merged all my devices so that if I miss messages or facetime calls on one device, they get forwarded to my other devices. how do I UNDO this so this no longer happens?

If you don't want them to be unified, don't use the same Apple ID for FaceTime and iMessage on our devices. Go to Settings>Messsages>Send & Receive, tap the ID, sign out, then sign back in with a separate ID. Do the same thing in Settings>FaceTime.

Receiving calls on multiple devices

for some reason, I am receiving calls on multiple devices when they are in close proximity. For example, if my wife receives a call then my son's phone and my phone will also ring. All devices have been logged out of the Apple ID. As far as I know, this is not happening with iMessage. Any suggestions??

That is a new feature described in Connect your iPhone, iPad, iPod touch, and Mac using Continuity - Apple Support
You can turn it off by going to Settings > FaceTime and changing "iPhone Cellular Calls" to off
You may also want to consider using separate Apple IDs. That is now more flexible with new Family Sharing features: http://www.apple.com/ios/whats-new/family-sharing/

My Gf has my iphone. How can I see recent messages and calls from another device?

My Gf has my iphone. How can I see recent messages and calls from another device?

Depending on your carrier, you may be able to see recent calls by logging into your account on the carrier's web site, if they offer such a feature, though incoming calls being shown is not usual. There will, as diesel said, be no way to see messages already received, either SMS/MMS or iMessages, without having the phone.
Regards.

An HNAP call to the device failed because the HTTP connection was broken - EA3500

OK - thanks in advance for your help -
I have a linksys Linksys WMP300 and am able to connect to the EA3500 (shows connected at 270 Mbps) Excellent Connecttion but I can't access the internet or any of the other computers on my network. The stupid thing is that I can connect to my neighbor's unsecured network which is also a linksys router.
All of the other computers on the network connected just fine - my son has a laptop running windows Vista, we have a family computer using Vista, my wife's laptop is Windows 7 (we just had a guest that connected just fine).
Here's the error code I get - any help would be appreciated!
Error code: 82BD0304
Error description: An HNAP call to the device failed because the HTTP connection was broken.
Model name: unknown
Model number: EA3500
Serial number: 12C10603215584
Firmware version: unknown
Operating system: Windows XP SP 3
Software version: 1.4.12005.2
Connection type (WAN): unknown
IP address (LAN): unknown
IP address (WAN): unknown
Computer IP address: 192.168.1.36

Thank you for the reply -
Router is assigning IP address automatically. Although I have been using a static IP address in the past, this is no longer the case.
The WMP300 is on an Windows XP, SP3 PC.
Since running into this issue, I have not only disabled all security (to make sure that firewalls and/or virus software was causing problems) I completely uninstalled my McAfee. I have disabled Windows Firewall also. "Flying Naked" as it were.
I am surprised that Cisco has no solution - others are also having this problem.
It MUST be the router - I am able to connect to my neighbor's router, able to connect to my old Linksys WRT150N. Anyone else have thoughts?
This is frustrating.

Can I merge database of multisim analog device version in multisim?

Can I merge database of multisim analog device version in multisim?
If yes, please tell me how. Thx!
I saw the file named "MSCOMP_S.prd" in the folder:
C:\Program Files\National Instruments\Multisim Analog Devices Edition 10.0\database

Hi Zenith,
The databases between the two products are not compatible and therefore cannot be merged. This database was created specifically for the Analog Devices Edition. Merging two "Master" databases is also not possible since the merge utility will only allow merging two "User" or "Corporate" databases.
Message Edited by M.I. on 12-03-2007 09:34 AM
M.I.
National Instruments
EWB Group.

Labview driver for Analog Device cards RTI 800 series

Hello,
I'm Mathieu Meisser, from EPFL Lausanne - microtechnique.
I'm working for a company, that produces
laboratory PC-controlled analysers, sold all over the world.
we are searching for the Labview drivers for the I/O analog Device
cards RTI 815/817 in order to developp a new intrumentation control
with Labview 5.0.
It's very important to know if any kind of these drivers are
still avaible and work properly.
please let me know as soon as possible if you know
something about this !
thank you for your cooperation !
Mathieu Meisser
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.

Hi Mohan,
Unfortunately there isn't a instrument driver specific to that device. What you could do though is use our NI-VISA driver and try to communicate with the instrument over serial (I assume it uses serial for communication) There are examples in the Example Finder (Help>>Find Examples) that ships with LabVIEW that will demonstrate some functions you can use. I hope this helps out.
Regards,
Michael
Applications Engineering
National Instruments

Which is a dual 2-bit bistable transparent latch IC in multisim analog devices edition

I need an equivalent IC for CD74HC75, which is a dual 2-bit transparent latch IC, for a project simulation. Cant find it in the Multisim reference guide.
Any suggestions??
Solved!
Go to Solution.

emind,
Hello, in the Multisim Analog Devices Evaluation Edition, you will find a D_Latch under the TIL family of parts (use 2 with EN tied together for a dual latch) that you can use for generic simulation purposes. If you need a specific latch from a manufacturer or specific logic family that might be challenging (we have a few in the PRO version or you can add some external circuitry to the TIL part to mimic the behavior of a particular logic family).
The TIL parts (generic digital I/O) are located here: Misc Digital (group) -> TIL -> D_LATCH.
I created a simple interactive circuit with a probe so you can observe the behavior to see if it will meet your simulation needs.
Regards,
Pat Noonan
National Instruments
Attachments:
bistable latch (ADI_edition).ms11 ‏36 KB

Feature request: Transfer call to another device

It would be nice to be able to transfer a call to another device by pressing a button and maybe an option to select a device but if not it just rings all logged in devices.

I would agree wiith Jaime, just configure the desired caller input in the user mailbox option by going toi edit---caller input.
In their you can either setup to transfer the call to another user with mailbox and select the option of "Go directly to greetings"
Or if you want the call transferred to a number either to the PSTN or a user who does not have an mailbox in unity connection, in order to do that, just select the option of Call Action and select "Transfer to alternate contact number". And put in the number as well as select the transfer type which plays a vital role in either sending a supervised transfer or an release to switch(which is not a supervised one, meaning it would send the call directly to the users phone without even making sure if the user is available or busy or if the phone is unregistered.
Hope it helps.

Trouble activating Multisim component evaluator Analog Devices Edition Version

I downloaded Multisim component evaluator Analog Devices Edition Version
13.0.. I’m having the same problem that I had last time I downloaded something
from NI. (Unactivated license). I think this is because of the tight security
where I work. The solution last time (after a lot of time and back and forth
emailing was to send me the activation code and I typed it in manually. (I
pasted that email below).
Thanks,
Brian
Brian Healey – Electrical Engineer – ISR Systems
UTC AEROSPACE SYSTEMS
7 Technology Park Drive, Westford, MA 01886 U.S.A.
Tel: +1 978 490 2148 Mobile: +1 978 846 5918
[email protected] www.utcaerospacesystems.com
From: [email protected] [mailto:[email protected]]
Sent: Friday, May 24, 2013 1:47 PM
To: Healey, Brian W UTAS
Subject: RE: [External] Re: (Reference#2014565) Phone Support E-Mail
Note: Your reference number is included in the subject field of this message.
It is very important not to remove or modify this reference number, or your
message may be returned to you.
Hi,
Open the License Manager again and try to activate Multisim, but this time
select the option to activate through a 20 - characer code.
Activation Code:
BS9P-HW36-4Z8Y-DJWM-C9N4
Let me know if this works.
Kind regards,
Miguel Vesco
Applications Engineer
National Instruments
http://www.ni.com/support

Hi Brian,
Since you have a new version the software needs to be reactivated with a new Activation Code. I will send you an email via our support system for further details.
Regards,
Fernando D.
National Instruments

Maxium calls on Analog devices CCM v.7

Similar Messages

Maybe you are looking for