Maxtor One Touch 3 is not showing on my desktop no more

Restarting computer Maxtor One Touch 3 doesn't show on my desktop. It will only if I pull the firewire our and in. It used to be OK. Even turning the power off or on on the Maxtor its still not showing.
Any idea how to fix that?

At this point I think you should get Applejack...
http://www.versiontracker.com/dyn/moreinfo/macosx/19596
After installing, reboot holding down CMD+s, then when the prompt shows, type in...
applejack AUTO
Then let it do all 5 of it's things.
At least it'll eliminate some questions if it doesn't fix it.
The 5 things it does are...
Correct any Disk problems.
Repair Permissions.
Clear out Cache Files.
Repair/check several plist files.
Dump the VM files for a fresh start.
If that doesn't work, try these...
Does it boot into Open Firmware with CMDOption+of ?
http://docs.info.apple.com/article.html?artnum=42642
Have you done a PRAM reset...
http://docs.info.apple.com/article.html?artnum=2238
Tried resetting the PMU?
http://docs.info.apple.com/article.html?artnum=14449

Similar Messages

Maxtor One Touch III not showing up on Mac OSX or Windows

ok so i have this Maxtor one touch III external hard drive that i used to use with my XP computer a few years ago... its 500 GB. so i plug it in to my Mac and install the software and it doesn't show up on my desktop or my disk utility. although, it does show up in my system profiler. so, it didn't work for mac... then i went onto my parallels account that has windows 7 on it and it still doesn't show up. what can i do to fix this?

SynGatesFan200 wrote:
Connection: USB
Version of parallels: 5.0
Section in system profiler: USB (shown as One touch III)
Software used: maxtor installation disc for one touch III (windows), downloaded maxtor one touch 4 software (mac)
Hi,
all this, with the exception of the Maxtor software, should indicate a no-problem with that HD.
Personally I have always avoided the provided software, since it is not needed for external HDs.
If you have access to a Windows PC try connecting the HD there and see what comes up.
And if you don't have valuable files on that HD, you might repartition it there as well.
Could be a rare case of a 'dynamic disk' http://support.microsoft.com/kb/314343/en-us which is something that Macs can't handle.
Regards
Stefan
Message was edited by: Fortuny

I can see my Maxtor drive, but it's not showing up on My Network- help!!

Hi there- Just installed my shiny, new WRT 610-N and have hit what appears to be a common problem.
BTW- I've searched the boards for a solution, so forgive me if this has been answered elsewhere and I just missed it....here's the story:
I can't access my external storage drive, that's plugged into the Cisco router. I can see it's obviously wired up properly, as it appears on Network Magic, but not on 'My Computer'.
I've tried to MAP the drive, as directed, but several XP components seem to be missing.
Also no problems LOGGING IN to the router- and under the 'Storage' tab, my Maxtor One-Touch II appears, clear as day, formatted to NTFS (but appearing as 'FAT' under the 'File System" column)
Confirmed the following settings:
-I'm running Windows XP, and like others here I'm not showing the 'Network Tasks' bar within 'Network Connections'.
Further, for the command string Explorer>Tools>Map Network Drive, I'm NOT getting the option to map the drive!!! ARRGH!
-I have checked the registry HKEY_CURRENT_USER\Software\Microsoft\Windows\Current Version\Policies\Explorer, and NoNetConnectDisconnect is enabled (1).
-The workgroup name under the routers 'administration' tab and my computer name are also matching, so no conflict there.
-I've assigned network access to another storage drive that's attached DIRECTLY to my cpu tower, and no problems exist with it.
-I'm running as the admin under XP with S/P 3 installed.
This would seem to be a registry issue but I can't solve it with the solutions posted elsewhere...anyone else finding issues with mapping external drives??
Any help is appreciated.
Thanks for your time.

First take the back of data you have on the hard drive then if you are able to see the hdd under storage tab then try to format the drive using the router utility. Now check if you can map the drive.

Maxtor One Touch II USB/firewire Ext HD won't mount

The drive shows up on the bus, but does not mount, and also does not show up with Disk Utility. I've taken it to the Apple Genius Bar and they couldn't find the problem, and said they only had 15 minutes to dedicate to me anyway. The drive didn't show on their MBP either. I've had this connected to my G4 for the past year, with no problem, and it still functions just fine there.
As another note, my Canon G6 Powershot, which has previously mounted on this machine (The MBP) via USB, no longer does. I can download photos directly into Iphoto, but the drive never mounts to the desktop.
I've tried both the USB and Firewire options with my external, with the same results. I need to download my photos from the MBP to the external, as it's getting pretty full. I noticed in another forum that FWT mode was not working with non-Intel macs prior to 10.3.9. but it's still not working between my G4 and the MBP.
I know there are several issues here, but was hoping someone could help me sort them out if I dump the whole scenario.
Any assistance would be greatly appreciated.
Macbook Pro Mac OS X (10.4.7) 1.83GB w/ 1GB DDR2 SDRAM
Macbook Pro Mac OS X (10.4.7) 1.83GB w/ 1GB DDR2 SDRAM

I have a one touch II that I purchased to use to backup and store files for my mbp.
Mine mounted correctly, but the one touch button did not work. After trying to fix it myself, I called the Maxtor tech support, and they said that they don't support using their drives or their software with intel based macs. Of course they only told me that after spending a long time on the phone.
So the only advice I can give to you is to not try Maxtor's tech support; it will be a waste of time.
Or perhaps your USB ports are broken and need to be replaced on your mbp.

Maxtor One-Touch back up, copying, etc. Driving me crazy!

As much I love my G5, one thing that drives me nuts is this:
If I copy a folder of 100gb from my main drive to my backup drive, where I had copied this same folder last week, but it now has 2 new files in it, I get a message which allows me to either overwrite the entire 100gb (even though only 2 files have changed) or cancelling.
What I REALLY need is some way for the computer to know that I only want the news files copied and to leave the other ones alone. If I open the folder and Select All, and then copy, i will have the opportunity to Replace or Overwrite, but that is way too cumbersome, considering the number and size of some of these files.
I think that my Maxtor One-touch has some way of doing what I want, but then that preseents other problems - like I can't selectively copy just some files, and if I'm copying from more than one drive to this backup drive, it gets complicated.
Is there a way to do what i'm trying to do?
Thanks.
G-5 Mac OS X (10.3.9) Maxtor One Touch external drive

Thank you all.
A couple of things:
First, I don't know much about hagis heid, or Scotland, but I have to say Craig Ferguson is perhaps the funniest latenight show host I've ever seen - he's fresh and spontaneous and really seems to enjoy what he's doing.
But to get back on topic, if I decide to use this new drive as a capture drive, I don't see "HFS Extended" as a formatting option. I've got Mac OS Extended (Journaled), Mac OS Extended and UNIX File System. Is that because on 10.3.9 and not on Tiger yet, or am I missing something?
If I don't use this as a capture drive, is it still advisable to format it? I find that it copies faster, if I don't.
One more question - my orginal one - even once properly formatted, how can I do my copying of files, in some intelligent way, where it will only overwrite files that need updating and not waste time with the others?
How do y'all approach that? What is your system of backup?
Thanks again.
G-5 Mac OS X (10.3.9)

My HP Pavilion 23 touchsmart all in one touch screen is not working

My HP Pavilion 23 touchsmart all in one touch screen is not workin. I have restored the system. I didn't see any place in the pen and touch to disable or enable and not sure if i should instill drivers. What can i do?

Hello @junk4are,
I understand that you are having issues with your HP Pavilion 23 Touchsmart Desktop PC's touchscreen and are wondering if you should install your drivers. I would certainly recommend that you do so. I would be happy to assist you, but first I would encourage you to post your product number for your computer as there are various versions of the HP Pavilion 23. I am linking an HP Support document below that will show you how to find your product number. As well, if you could indicate which operating system you are using. And whether your operating system is 32-bit or 64-bit as with this and the product number I can provide you with accurate information.
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the requested information and I would be happy to provide you with assistance. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Powerbook 15" w/ Tiger won't read Maxtor One Touch II External Hard Drive

Hi all:
For some reason my G4 Powerbook can't recognize my Maxtor One Touch II external hard drive. I am trying to find a firewire cable that fits, as the Maxtor just gave me a USB and says that the cable won't work with mac. I am trying to find a cable that has a "printer type" end and a firewire end. Will it help? Where do I find it?
Thanks,
Chris

No the printer type end, won't work in Mac OS X either. The software that is included with One Touch does not work well on Tiger or later. Instead I recommend not using that software, and instead using Shirt Pocket Superduper for backup. Or look for EMC/Dantz to update the drivers for the included software to Tiger. I think the One Touch does have a Firewire 6 pin connector which is Mac compatible. These ports look like the Firewire port on your G4 Powerbook. Port number 2 below is a Firewire port:
You can buy the cable from the Apple Store, or any major Mac mail order shop such as Macwarehouse, Maczone, Macconnection, or even CDW.

What format should I use for Maxtor One Touch III external hard drive

I'm not sure if I'm on the right forum section, but hopefully you can help. I just got a Maxtor One Touch III external hard drive with the firewire 400/usb 2.0 port. I installed the cd and followed the manual and it told me to format it. I went to disk utility and went to the "erase" section, but now it wants me to choose the type of format: mac os extended (case-sensitive), mac os journaled, mac os (case-sensitive, journaled) and so on.... Can anyone tell me what those formats mean/do, and what is the best one to use? Thanks!

Case sensitive is really if you are using some old UNIX programs that you have brought the source over to OS X and compiled them. And the UNIX programs have to expect a case-sensitive file system.
I'm betting this isn't the case... or you'd know what a case sensitive file system is.
So go with HFS+ Journaled

MAXTOR ONE TOUCH III 1TB 1000GB EXTERNAL HARD DRIVE on MacBookPr0?

Need more Ext HD storage for iTunes on my MBPro Is anyone using a MAXTOR ONE TOUCH III 1TB 1000GB EXTERNAL HARD DRIVE this drive on MacBookPro, is it any good? Advise

The Maxtor one-touch models, comes with a EMC Retrospect startup item to run its backup software. I tend to disable this functionality, as it often is not updated for the operating system actually being run and can cause problems with setting up. Instead, I use Shirt-Pocket Superduper for backing up. I'm not sure the Maxtor is bootable on a MacBook Pro, but when you first get it, you'll want to reformat it with Disk Utility to have a GUID partition for optimized backing up for the MacBook Pro.
If you plan to use it with a Windows machine, you'll not be able to use it for full backing up, but at least data files will store on it, if you format it FAT32. Your alternative is still to format it GUID, but get MacDrive by Mediafour for your Windows machine to be able to read the drive, or network it use the built-in networking of the Mac as described here:
http://docs.info.apple.com/article.html?artnum=19652
If you aren't, well the above paragraph is just extra non-essential info!

Mac Book Pro MAXTOR ONE TOUCH III 1TB 1000GB EXTERNAL HARD DRIVE

Need more Ext HD storage for iTunes. Is anyone using a MAXTOR ONE TOUCH III 1TB 1000GB EXTERNAL HARD DRIVE this drive on MacBookPro, is it any good? Advise

That drive is fine. No reason not to use it.

Maxtor One Touch III won't Mount

Similar problem to others. Hard drive won't mount on computer despite being able to identify it within the Airport utility. I have tried numerous suggestions already listed including: Hard Resetting multiple times the Express, Reformating Hard Drive, Restarting computer, Using different computers. My external hard drive WILL MOUNT if I do a direct USB connection into the computer.

I just set up my new AirPort Extreme Base station,
and I can confirm that it DID mount my 500 GB Maxtor
One-Touch III which I purchased this week.
I am using 'n' only on 5GHz.
I had to open up the AirPort Disk Utility. Then a
window popped up asking for a password. I used the
password that I set to make changes to the Airport
base station - NOT the password you use to access the
network.
I am copying stuff to it now. I was hoping it would
be faster, to be honest. 2GB has taken 13:30 to
transfer. According to my math....thats about
2.5MB/sec.
Thank you for the response. I am unfortunately am not asked for a password. I am not however using your configuration as I have an older laptop that does not have a 'n' card.

Maxtor One Touch II Won't Mount

I'm running 10.6.8 and my maxtor one touch II won't mount all of a sudden? I've tried fire wire 400 and fire 400to800, restarting etc. The drive won't show up?
The driver update on the Maxtor/Seagate site opens up as code in a text edit file, it doesn't show up as the typical box to be unstuffed. Either way, it's an old update and I've been using this external drive for years. It's definitely spinning, but the computer just can't find it.

re:
Re: Maxtor One Touch II Won't Mount
Jan 1, 2012 8:19 PM (in response to RothHaus)
Can Disk Utility see it? If so try repairing the drive.
As it turns out I finally got the drive to mount, after several attempts. It was simply a matter of there being less than a gig free on the maxtor so it was having trouble booting up.
Thank you for the response!

HELP Maxtor One Touch III 1TB External Fails after upgrade to 10.5.7

Hello,
I was using a Maxtor One Touch III for my iTunes music (over 400gb) and when I upgraded to 10.5.7 last week my Intel Mac Pro froze several times, causing me to hard power down the computer.
My External drive now makes a clicking noise when it starts up for about 30 seconds, then stops, power light stays flashing. It does not mount.
I have tried Disc Utility (repaired permissions and repaied main internal drive after update), Disc Warrior and now Data Rescue II. All are not seeing the external, and I have tried it via both firewire and USB.
I see other people are experiencing this with other drives, has anyone had this issue with an external like mine? I had over 400GB of music, movies, etc on this 1TB drive.

ok here's where I'm at with this debacle.
I've checked my internal disk for reduncancy and have decided just to wipe it, replaced it with a 1TB SATA and used time machine to roll my data back on there. That will take care of the freezing, etc. I also had some issues with some of the 14GB of RAM I had installed (6GB of it was not "Mac Approved" but worked), but I think helped caused this issue of freezing with the update. So now down to 8GB of RAM (nuts!)
As for my external maxtor. I took apart the enclosure and mounted the SATA drives internally in my mac pro, then used Data Rescue II to get what remaining items I could off of one of the drives. The other drive is toast and just continues to keep clicking, etc. I thought by eliminating the maxtor power supply and mounting it internally I may have better luck. Not so much.
To your question about reporting to apple- I spoke to several tech specialists I know very well @ Apple and all were very helpful but most agreed that once the drive begins clicking and not mounting, there is a good possibility of your data having been lost. So aside from using a "Data Recovery" company and exhausting thousands of dollars, I am resolved to the fact I will just take the music I was able to recover (about 1/3rd of what was lost) and Ill spend the next few months scanning in discs I have, and contact apple about re-downloading purchases.
Moral of the story- BACK UP YOUR DATA! I had everything else (other than my 400+GB of music) backed up in about 3 places including time machine. Thank GOD since I have 250 GB of photos which I wouldnt be able to fathom losing.
If you had the same problem and were able to resolve I am envious, so far this has taught me not only to back up EVERYTHING but not to jump on the update bandwagon until all of the bugs are gone.
In the process I have lost hours of time but was able to learn more than I ever wanted to know about hard drives.
Keep us updated if you get resolution.

Leopard and Maxtor One Touch III Turbo - changing RAID setup

Hi-
So I just picked up a Maxtor One Touch III Turbo (1.5TB) - installed the Maxtor One Touch Manager, and have tried to change the RAID Setup to Raid 1.
The Maxtor OneTouch Manager software does not respond - it is set by default to RAID 0 (not ideal).
I installed the update to the software from Maxtor (now Seagate) - but still no dice.
Has anyone had any success using the Maxtor One Touch Manager to change the HD from RAID 0 to RAID 1 on Leopard?
Thanks.

Ok so I have not received a response from Seagate yet but after some additional reading in the forums I decided to plug my drive into an iMac, that I have not yet upgraded to Leopard, and BAM it works fine.
All I installed was the updated Intel version of the OneTouch Manager, not the entire CD. The RAID change works perfect and all tests passed.
It appears that it is just not compatible with Leopard.
The only concern I have is when that when I upgrade my iMac and then not have the ability to test the drives on my MacBook Pro if one of the drives appears to or goes bad.
I will still follow up with Seagate and if anything comes of it I will let you know.

Maxtor One touch external hard drive

Ok, I have tried doing a query on this question and have come up empty. I recently bought a maxtor one touch 500 gig drive. I knew that I wanted a drive for backing but more so for adding room to use as our main drive. We bought a video camera a year ago and would like to upload the footage but do not have enough room on the original drive to add more than 45 minutes of video. Is there anyway to make iMovie look at the external drive to upload any new material? Or do I have to set (if possible and if so how do I) the maxtor as the bootable drive?

Ya, when you set up a new project, just select the little triangle next to the file name field to expand the save box to see and select other drives...
http://www.danslagle.com/mac/iMovie/usage/5006.shtml
Patrick

Maxtor One Touch 3 is not showing on my desktop no more

Similar Messages

Maybe you are looking for