May I deploy MS patches on windows servers, and reboot the servers later?
Hello,
I am trying to steam line patching process. May I deploy MS patches on the windows servers first and then reboot the servers at a later time? say days later.
Tiffany
For CCM, that is a big no. You need to get the updates that have been approved by Cisco from Cisco. They are available at the following link. Read the release notes very carefully! There are very strict upgrade sequences. I suggest that you consider upgrading to UCM 6 or 7; the updating process is much easier.
Cisco Unified CallManager Version 4.1 > Voice Application OS and BIOS Updates
For Unity, you can typically download and run the Update Wizard which will have the approved updates rolled in. Depending on how immediate you want to be about it, there is also a support policy for Windows Update
Software Installed by the Cisco Unity Server Updates Wizard in 2009 .
Similar Messages
-
How do I fix my left shift key? Any open windows leave and make the desktop visible.
How do I fix my left shift key? Any open windows leave and make the desktop visible. I have tired to go into system preferences and reset all of the keyboard settings to default but the issue hasn't gone away.
You are not running as administrator, I think, which may be required and the only way to properly work and register. Also check for compatibility mode settings, UAC and DEP, all of which may require to be adjusted for a legacy app like PS CS2 to run properly. Also turn off Aero and switch to a conventional visual theme. The brush issue may be related to that or is a more generic problem with your graphics card and mouse config, but since you didn't provide any info on that, it will be hard for anyone to advise.
Mylenium -
Trying to install itunes on windows vista and get the following error message:
Trying to install itunes on windows vista and get the following error message: An error occurred during the installation of assembly "Microsoft.VC80.CRT,version="8.0.50727.4053",type="win32",publicKey Token="1fc8b3b9a1e3b",process orArchitecture="x86"". Please refer to Help and Support for more information. HRESULT: 0x80070424.
A broken Windows Modules Installer then. It's a bit of an involved fix getting past it, but we've had success here with it in the past.
First, I'd strongly suggest setting up a system restore point.
Now try the Scenario III treatment from the following document:
Windows Update Error 80070424 in Vista
Head back into Windows Update and attempt to get updates again. If they still fail, this time with an 8000FFFF error code, try the following Microsoft document:
Windows Update error 8000FFFF
If you get Windows Updates flowing again, stock up on any you're behind on (restarting the PC when requested to do so). This may take some time and may have to be done in several batches, depending on how far you've fallen behind. Basically, keep going back to Windows Update until it stops offering you new updates.
After the updates have been installed, restart the PC one more time (in order to ensure that any pending installs requiring a restart have been resolved).
Now try another iTunes install. Does it go through without the 0x80070424 this time? -
When in Adobe Bridge and trying to create a web photo gallery, under the windows menu and then the workspace menu there is no output option. Where is it?
You haven't provided any sensible, meaningful and detailed information about your setup.
If you gave some sensible, complete and detailed information, someone may be able to help you, such as your platform (Mac or Win), exact versions of your OS, of Photoshop and of Bridge, machine specs, what troubleshooting steps you have taken so far, etc.
There are no clairvoyants or mind readers here.
Please read this FAQ for advice on how to ask your questions correctly for quicker and better answers:
http://forums.adobe.com/thread/419981?tstart=0
Thanks! -
Adding a Patch to a Pocket and keeping the Folds and Wrinkles - CS3
I have a photo of a gentleman wearing a typicl denim shirt and I would like to add a patch, or an emblem, to the shirt pocket. I would like the patch to follow the contours of the shirt, including the folds and wrinkles. How can that be done in CS3? Thanks
Using CS3, Windows XpThanks for the reply. I wasn't looking for an automated way to get the job done. I tried using the transform tools last week, and the results were OK for the specific image I was working on, but something else (displacement filter?) might be better still. Have to play around with that.
Kind Regards,
SCB
Date: Wed, 5 Oct 2011 10:46:51 -0600
From: [email protected]
To: [email protected]
Subject: Adding a Patch to a Pocket and keeping the Folds and Wrinkles - CS3
Re: Adding a Patch to a Pocket and keeping the Folds and Wrinkles - CS3 created by Noel Carboni in Photoshop Windows - View the full discussion
I don't think of an easy automated way to do it. I'd probably paste it on there, maybe distort / transform it a bit as needed (e.g., if the wrinkles are deep), then use the Burn and Dodge tools to add subtle shading to make it look believable.
-Noel
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/3955361#3955361
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/3955361#3955361. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Photoshop Windows by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
How can I switch off the automatic window size and set the size of the window manually
I need to open the web-page in a window of a certain size. The javascript function window.resizeTo (w, h) does not work. If I open the window using the window.open ("", "", "width: w, height: h, ..."), there is another problem.
The hyperlinks that have to be opened in a new tab in the same window or at least in the window of the same size, will open in another tab of the first window from which I called window.open().
I do not know what it is, bug or as intended, but the normal full-featured window with the right size I cannot get.
In Russian:
Мне нужно открыть страницу в окне определенных размеров.
Из консоли Firebug с помощью javascript пробовал window.resizeTo(w,h) - не работает. Если открывать окно с помощью window.open("", "", "width:w, height:h, ..."), то возникает другая проблема: ссылки, которые должны окрываться в новой вкладке в том же окне или хотя бы в окне того же размера, открываются в другой вкладке первого окна, из которого я выполнял команду window.open(), которое неправильного размера.
Не знаю, что это. Баг или так задумано. Но открыть нормальное полноценное окно с нужными размерами не получается никак.You need an extension if you want to set the window dimensions to a specific value or you need to open a pop-up window with window.open and specify the width and height.<br />
Otherwise a new window opens with some default dimensions as saved in localstore.rdf and you can't easily adjust the dimensions via JavaScript in that case. -
I put a windows xp cd in my macbook pro and rebooted the mac,mac doesn't come up any more and the cd doesn't come out,what can I do now?
Hossein,
As Guido said, you can use BootCamp to partition the drive. If you want to install, or reinstall Windows. You would launch BootCamp and it will actually guide you through the installation, you will only need to decide how large a partition you want. I would use BootCamp, I would not use disk utility. When you have installed Windows and you want to boot into windows, when you start your MBP hold down the option key, this will give you trha option of booting Mac OSX or Windows.
Joseph -
I partitioned a small drive for a windows program, and now the computer only wants to boot to Windows. How do I get back to Mac so I can have a choice of drives?
That doesn't sound good. It sounds like the power outage might have corrupted the partition for OS X. I would suggest booting from the Install DVD that came with your Mac while holding down the C key. Once you have selected the language start up Disk Utility from the pull down menu and repair the disk. Once you have done that then repair permissions also.
Allan -
Preparation for installing bootcamp and windows 7, and in the absence of a DVD drive
I am not sure that I submitted this with the right boxes ticked, so i am re submitting it!
In preparation for installing bootcamp and windows 7, and in the absence of a DVD drive on my MacBook Air, before starting, can I partition my external drive (for use with my Mac) to have an ISO image file location for Windows downloads?
CyfromayoThe Boot Camp instructions are located here: http://www.apple.com/support/bootcamp/
The Boot Camp Discussion Community is located here: https://discussions.apple.com/community/windows_software/boot_camp -
i just buy a imac 27inch when after intalling everthing for windows 7 and all the drivers i need and goes to the restard part my imac just goes to a black screen with a blinking cursel and it just wont proceed anyone can help me with this?
Support articles for things like this would be here:
http://www.apple.com/support/bootcamp -
For the last 3 or 4 versions of iTunes, and continuing in 11.05, the site recognizes that I have a 64 bit OS (Windows Vista) and downloads the 64 bit version of setup. Setup installs iTunes in the 32 bit application directory (Program Files x86) - it's not all that unusual to run a 32 bit app under a 64 bit OS - BUT whenever I connect any of my iPhones, I get an error message that say I cannot use the iPhone because the 64 bit version of iTunes is not installed. The message then tells me to de-install iTunes and to install the 64 bit version.
Like I say, the 64 bit Setup version is selected for me, and it runs error-free, but I seem to have no control or ability to force the installation of a 64 bit iTunes app. And all the iPhones are inoperative with the 32 bit version I have. I have another PC, which I have held at an earlier iTunes release. Although it's a notebook, it's identical in every other way (OS & installed utilities and apps) to the desktop that has developed the problem, and my iPhones work fine with it, although iTunes on it is at the earlier release, and I have no intention of upgrading that version until I understand and have corrected the problem.
Any ideas or suggustions?
Thanks.This iPhone cannot be used because the required software is not installed. Run the the iTunes installer to remove iTunes, then install the 64 bit version of iTunes.
That usually indicates that your Apple Mobile Device Support has not installed. That's also what is being shown by the diagnostics (the driver is there but the application isn't).
Let's try a standalone Apple Mobile Device Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of why it's not installing under normal conditions.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/
Right-click the iTunesSetup.exe (or iTunes64setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleMobileDeviceSupport.msi (or AppleMobileDeviceSupport64.msi) to do a standalone AMDS install.
(If it offers you the choice to remove or repair, choose "Remove", and if the uninstall goes through successfully, see if you can reinstall by doubleclicking the AppleMobileDeviceSupport.msi again.)
Does it install (or uninstall and then reinstall) properly for you?
If instead you get an error message during the install (or uninstall), let us know what it says. (Precise text, please.) -
HT1926 download does not start i am using windows 7 and checked the pop-up blocker
download does not start i am using windows 7 and checked the pop-up blocker
Create a new profile as a test to check if your current profile is causing the problems.
See "Creating a profile":
*https://support.mozilla.org/kb/profile-manager-create-and-remove-firefox-profiles
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Profile_issues
If the new profile works then you can transfer some files from an existing profile to the new profile, but be careful not to copy corrupted files.
*http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox
A possible cause is security software (firewall,anti-virus) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox and the plugin-container from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process and the updater process.
See:
*https://support.mozilla.org/kb/Server+not+found
*https://support.mozilla.org/kb/Firewalls -
is there a way to get photos off of a thumb drive onto something that can be uploaded to the ipad. I am doing away with my windows systems and using the ipad exclusively?
iPad Photo Recovery: How to Recover Deleted Photos
http://www.iskysoft.com/iphone-data-recovery-mac/ipad-photo-recovery.html
How to Restore Lost or Deleted Files from iPad
http://www.iphone-ipad-recovery.com/recover-ipad-mini-files.html
How to Recover Deleted Files from iPad
http://www.kvisoft.com/tutorials/recover-deleted-files-from-ipad.html
How to Recover Photos from iPad
http://www.ipubsoft.com/idevice-tips/recover-deleted-photos-on-ipad-mini.html
iSkysoft Free iPhone Data Recovery
http://www.iskysoft.com/iphone-data-recovery/
Recover iPhone/iPad/iPod touch lost data, Free.
Free recover iPhone/iPad/iPod touch lost contacts, photos, videos, notes, call logs and more
Recover data directly from iPhone or from iTunes backup
Preview and recover lost iOS data with original quality
Wondershare Dr.Fone for iOS
http://www.wondershare.net/data-recovery/iphone-data-recovery.html?gclid=CJT7i9e 6gb4CFcvm7AodbUEAJQ
Recover contacts, messages, photos, videos, notes, call history, calendars, voicemail, voice memos, reminders, bookmarks and other documents.
iPad Data Recovery Software (PC & Mac)
http://www.anysoftwaretools.com/ipad-data-recovery.html
Jihosoft Mobile Recovery for iOS
http://www.fonerecovery.com/iphone-data-recovery.html
Cheers, Tom -
How may I print out a picture from paper and not the photo tray?
How may I print out a picture from paper and not the photo tray?
From paper? Do you have a digital image of it on your iPhone?
"Photo tray"? What do you mean here? The iPhone does not have a photo tray. Printers have trays. -
Out of the blue my sim card is no longer recogniced and i got a "sim invalid" window. once i reboot the phone everything goes back to normal. What can i do to solve this trouble?
Replace the sim card
Maybe you are looking for
-
Number Overflow when it is within the range (Long)
Hi, I am using Oracle JDBC Drivers to write a CMP (Container Managed Persistance) beans which has a CMP Field of long value in the table it is Number(14) which is well under the limits of long datatype, the value is also currentmillis which is millis
-
Not possible to determine shipping data for material in PO(STO)
I m doing STO for intra copmany code(plant to plant stock transfer),I have done all STO setting ,maintain material with plant and storage condition,loading groups , maintain customer with storage condition,created vendor with supplying plant.setting
-
What the best to buy iPad please
Hello are you there ?
-
I am trying to install Adobe Air on my Mac but get a An error occurred while installing Adobe AIR. Installation may not be allowed by your administrator. Please contact your administrator." Posted solutions don't seem to work. Looking at the log,
-
I have French as a subject, and I was planning to use Pages to help me with it. So I have a couple of problems: 1. Pages language set to French, French words still come up wrong, although they are right. 2. Unable to get speech to say the French, jus