May I know cisco 2600/2700 support for VPDN or not?

Hello guys,
I'm planning to setup a lab for VPDN test. I only have 2600/2700 series router on hands, may I know can they fully perform (1)dialer, (2)LAC, and (3)LNS? Thank you for your great share!

Yes, you should be able to.
Hope this helps, please rate post if it does!

Similar Messages

Does Cisco Prime have support for HP Access Points?

I am trying to sell a solution to a client with dozens of large warehouses with a large existing HP wireless solution. I want to sell them on a Cisco wireless solution involving Prime to manage/monitor their current HP Access Points while we do a phased replacement to Cisco WLC and APs.
I cannot find listed in the documentation whether Cisco Prime has support for the HP access points though. I see it has 'some' support listed for some Aruba controllers, but not anything else.

I am trying to sell a solution to a client with dozens of large warehouses with a large existing HP wireless solution. I want to sell them on a Cisco wireless solution involving Prime to manage/monitor their current HP Access Points while we do a phased replacement to Cisco WLC and APs.
Prime will only support products with a "Cisco" logo.
Note: Prime 2.2 will start supporting Meraki product.

NI-DAQmx support for labview could not be found

Hi, I am pretty new to LabView. I was using VC++ to programming for my USB-6215. Just curious how LabView works, so I try to follow the "Introduction to Taking an NI-DAQmx measurement in LabView" and configure my USB-6215 in LabView. However, when I try to gererate codes for the DAQmx task name control, an error message pop up as "Error:NI-DAQmx support for labview could not be found. Please reinstall NI-DAQmx". I did reinstall NI-DAQmx, but it doesn't help. This error occurs anyway. Any idea how it happens and the solution is highly appreciated. Thank you.
Jingyu

See attached
Paul Falkenstein
Coleman Technologies Inc.
CLA, CPI, AIA-Vision
Labview 4.0- 2013, RT, Vision, FPGA
Attachments:
MX picture.PNG ‏35 KB

Cisco 2600 voice IP for FXO interface

Hi all,
Pls help me step by step configuring Voice IP for Cisco 2600 using FXO interface.
Thank you very much.

It all goes by what you want to cofigure. FXO interface generally connects with PBX or PSTN..
Some config examples using FXO ports, visit
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/inst_nts/acc_gtwy/voice.htm
One more good link on that
http://www.cisco.com/warp/public/788/signalling/fxo_disconnect.html

Cisco Multicast Manager Support for NEXUS

Hi All,
Does Cisco Multicast manager support Nexus devices ?
Please help.

No at this time it does not according to the data sheets:
http://www.cisco.com/en/US/partner/prod/collateral/netmgtsw/ps6504/ps6335/ps6337/q_a_c67-527951.html
You can use cisco data center manager for managing Nexus devices:
http://www.cisco.com/en/US/products/ps9369/index.html
Download software:
http://tools.cisco.com/support/downloads/go/Redirect.x?mdfid=281722751

Citrix goto webinar and cisco webex no support for playbook

http://support.citrixonline.com/en_US/gotowebinar/all_files/GTW010004
As business tablet rim should get support for these 2 important business application

ofcourse it should come from product vendor, either citrix or cisco, but RIM has to put some effort to bring these apps to their platform. People have been crying for webex and skype for past one year but no luck yet. Webex is a widely used apps for meeting and remote support and its pathetic that RIM is waiting for someone to develop an app someday. That strategy is idiotic and so playbook is a great failure.

Is there any planned support for the "do not back up" extended attribute for iOS

Starting in iOS 5.0.1, Apple has introduced a new "do not back up" extended file attribute that will allow an app to store downloaded data into the application folder. Is there any planned support for setting this attribute within an AIR application or is there currently a way to set this attribute using the existing AIR SDK.

Yes, this is exactly what I'm wondering too. Without it, we can't build any apps that download content without the risk of the content being deleted.
Here's the background before Apple introduced the new "do not back up" attribute:
http://www.marco.org/2011/10/13/ios5-caches-cleaning
Fortunately, Apple addressed it after that blog post in 5.0.1. See bullet #4 here, quoted below
https://developer.apple.com/icloud/documentation/data-storage/
Q: My app has a number of files that need to be stored on the device permanently for my app to function properly offline. However, those files do not contain user data and don't need to be backed up. How should I store those files in iOS 5?
A: Starting in iOS 5.0.1 a new "do not back up" file attribute has been introduced allowing developers to clearly specify which files should be backed up, which files are local caches only and subject to purge, and which files should not be backed up but should also not be purged. In addition, setting this attribute on a folder will prevent the folder and all of its contents from being backed up.
Important: The new "do not back up" attribute will only be used by iOS 5.0.1 or later. On iOS 5.0 and earlier, applications will need to store their data in <Application_Home>/Library/Caches to avoid having it backed up. Since this attribute is ignored on older systems, you will need to insure your app complies with the iOS Data Storage Guidelines on all versions of iOS that your application supports.
Now we just need Adobe to support the attribute in the AIR SDK. What do you say Adobe?

How can I tell with % how fast I am uplaoding a file...I know how to find it for DOWNLOADING, but not uploading.

I just switched to Firefox...I used to have Google Chrome...when I would upload a file, a % number would scroll at the bottom showing me how much has been uploaded....how do I find that on Firefox....I know how to find the DOWNLOAD box, but not one for UPLOADING opr sending files

I mistyped in my first post. I do indeed mark the video as AF41 (Cos4). It is the call control that I mark CS3 with the policy map to get around the old Tandberg bug that doesn't mark the call control.
So do you think the queue 3, where Cos4 goes to, is big enough to handle 30 video streams of 480k? If my calculation is correct that would be 14.4mbps of video on a 100mbps port.
With this config.....
srr-queue bandwidth share 10 10 60 20
srr-queue bandwidth shape 10 0 0 0
...is it telling me that queues 1 & 2 get 10% bw, queue 3 gets 60% and queue 4 gets 20% bw and is shared? If that is correct than 60% is more than enough for 14.4mbps of video.
What happens if too much video overruns the queue?

Cisco RV215W and support for Huawei E3276.

I have a number of these devices, bought after testing that the combination did actually Work.
Unfortunately our phone operator (Hi3G Denmark) has shipped the E3276 HiLink version, which seems not to be supported in the RV215W.
Any possibility for support of the Huawei E3276 HiLink in the RV215W firmware?
Best regards
Kristian Hansen

Khansen,
I have reviewed the dongle list for Denmark support and you correct is not supported. If i may suggest try opening a support case with Small Business Support Center. Just keep in mind that demand for this particular dongle would have to be high to support it and add to list.
Dongle list:
https://supportforums.cisco.com/document/127976/rv215w-supported-dongle-modems

Cisco 8945 IPT support for the UC540?

Hi All,
Is the Cisco 8945 IPT ever likely to be supported on the UC540?
Many thanks
Matt

mchandak,
Honestly I don't know what makes you believe that.
1) the main protocol/standards used on ISDN PRI are from bottom to top, G.703, G.704, Q.921 and Q.931, no matter if you have H.323, SIP, MGCP or SCCP as VoIP signaling protocol.
2) CCME can perfectly "control" a gateway using any of above protocol except MGCP.
3) In the original question, there is no gateway/backend, just one single CCME router.

Cisco supervisor Desktop support for Windows 7

We are getting ready to rollout Windows 7. We ran into a problem while testing Historical Reports and Cisco supervisor Desktop on Windows 7. Historical Reports installs just fine while CSD give us an error that the operating system is not supported by Cisco. Is there a current version that supports Windows 7?
Our IPCC version is:
Cisco Application Administration - 7.0(1)SR05_Build504
Package: Cisco Unified CCX Enhanced
Any help with this issue would be greatly appreciated.
Thanks,
Yefim

Yes, you are wandering down a long and lonely road.
Repackaging an install package from an .exe (which could be one of a million types of installer, such as InstallShield) to an MSI isn't a trivial task - it's a fairly specialist piece of work.
You can only open MSIs with Orca, it doesn't support other types of install package.
I would suggest if you have a workable solution with ThinApp you'd be best to leave it there...
Aaron

Anyone Knows that NAS/NFS supported for TimesTen's Checkpoint & Log files?

Like Subject!!!
Checkpiont files and Transaction log file can placed NAS/NFS network file system ?
Thank's your help

Per the 11.2.1 Release Notes this is only supported on Linux x8664. There is a special ttendaemon.options parameter to set:
-allowNetworkFiles
Please see the section "Allowing database access over NFS-mounted systems" in the Operations Guide

How to know Whether Partition is done for Cube or not

Hi All,
I need information regarding Partition of a cube.
a)How do i know the Partition is done or not for Cube
b)On what basis we should make parttion of Cube.
Thanks and Regards,
C.V.

There are several threads on partitioning, so it would be a good start for this question (as with any question) to search the BI forums on "Partitioning" and review thsoe first.
Some basic considerations on partitioning -
- Your DB must support Range partitioning to permit partitioning your InfoCube. The option will be greyed out if it is not available.
- InfoCube must be empty to be partitioned.
- InfoCube can only be partitioned on 0FISCPER or 0CALMONTH. You can define it so that you have a partition for each month/fiscper, or so that each partition will hold a few or several months of data.
- Generally, you would not partition small cubes.
- Thru BW 3.5 Aggregates automatically get partitioned the sme way the InfoCube is partitioned as long as the partitioning characteristic is in the aggregate. In 2004s, I believe you have options as to whether an aggregate gets partitioned or not.
- Partitioning may be done for query performance reasons and data administration. If the queries on the InfoCube regularly run with restrictions/filters on the partitioning characteristic (FISCPER or CALMONTH), the database will "prune" any partitions that do not contain the FISCPER/CALMONTH value(s), so that it does not need to consider them , e.g. most of your users only run a sales query for the current and previous month, but your cube contains 3 years of data. By partitioning on CALMONTH (we'll assume 1 partition / month), the database will exclude all but the two partitions from consideration. This could help query performance a lot. or maybe only a little, depending on a variety of other factors.
Again - it is important that the queries restrict onthe partitioning characteristic to be of any value on query performance. So don't partition on FISCPER if all the queries use CALMONTH for restrictions.
The data adminsitration reason you might partition is to improve selective deletion or archiving time. These processes are capable of using a DB function to Drop the partition, which quickly removes the data from the cube, rather than having to run a resource intensive Delete query. This only happens if you deletion/archiving criteria is set to remove an entire partition of data.
Again - review the other threads on the BI forums on Partitioning. Most questions you have will already have been asked and answered before, and post again on SDN if there is something you still have a question about.

Support for xbox is not working!!!

To whom it may concern,
i own a 360 xbox prior to kinect and has been working fine with all updates for years up to the last 6 months.
i travel between friends house and use the online service to access my account for many years and it has never been a issue till last year when i could not access my account when i return from my friends house. it took 4 days to get back online i used all
the suggestions at the time and contact support but gave up when no help was given. when i decide to turn back on the xbox, just by chance that the online service was back on. for the rest of the year ive continue to have sporadic indicents that seem to have
nothing related to the xbox and figure it was do to the internet connection till now, i have been with out service to my account for a week at my house and i have made several attempts to contact the support service online on my pc as my friends samsung phone.
I also used all the suggestion that have been give by the system as well as the internet which is provided by microsoft via xbox division. still to this day my xbox is not connected to my xbox account.
i feel even though i use an older xbox model(that many of my friends still use and some work fine with the updates and others have switch to PS4 for similar reasons) that the quality and care about a product should still be a concern for the company even
though newer versions come out, especially since tech support is provided. i dont want to say that i dont upgrade but if im getting this kind of service and help now, i feel that if i decide to get the new system i will receive the same support and when do
need the help im not gonna be able to get it.
Untill these issues are resolve i feel that there no reason to renew my account or purchase a new model xbox. As well as tell friends to invest there time in xbox if there just gonna deal with these issues.
thank you for your time, hope that issues will be resolved and that when i ask my friends how the service is hopefully its for the better.

To whom it may concern,
i own a 360 xbox prior to kinect and has been working fine with all updates for years up to the last 6 months.
i travel between friends house and use the online service to access my account for many years and it has never been a issue till last year when i could not access my account when i return from my friends house. it took 4 days to get back online i used all
the suggestions at the time and contact support but gave up when no help was given. when i decide to turn back on the xbox, just by chance that the online service was back on. for the rest of the year ive continue to have sporadic indicents that seem to have
nothing related to the xbox and figure it was do to the internet connection till now, i have been with out service to my account for a week at my house and i have made several attempts to contact the support service online on my pc as my friends samsung phone.
I also used all the suggestion that have been give by the system as well as the internet which is provided by microsoft via xbox division. still to this day my xbox is not connected to my xbox account.
i feel even though i use an older xbox model(that many of my friends still use and some work fine with the updates and others have switch to PS4 for similar reasons) that the quality and care about a product should still be a concern for the company even
though newer versions come out, especially since tech support is provided. i dont want to say that i dont upgrade but if im getting this kind of service and help now, i feel that if i decide to get the new system i will receive the same support and when do
need the help im not gonna be able to get it.
Untill these issues are resolve i feel that there no reason to renew my account or purchase a new model xbox. As well as tell friends to invest there time in xbox if there just gonna deal with these issues.
thank you for your time, hope that issues will be resolved and that when i ask my friends how the service is hopefully its for the better.

HT1420 i know my username and email for gamecenter but not my password or email how can i retrieve infor its diff. from my apple id though

ok here it is.. im pretty sure im logged under s s for user and scottantnoah for my nickname for game center.. i deleted my iphone and lost all info.. whenever i go to gamecenter and put my email in it says that email is allready being used.. thats the email i need to sign in and its mine thats logged in and it wont log off.. how do i find out how to log in under that email. i forgot original apple id email so i created a new one. i need help

Hey smthchrst,
You can view what Apple ID you're using with Game Center in your iPhone's settings:
You can view and change your nickname, Game Center profile, and friend settings from:
iOS: Tap Settings > Game Center.
Using Game Center
http://support.apple.com/kb/HT4314
Welcome to Apple Support Communities!
Sincerely,
Delgadoh

May I know cisco 2600/2700 support for VPDN or not?

Similar Messages

Maybe you are looking for