MBox - All lights are on, no one is home

Hi, I'm Ryan. I have been using the original MBox with Logic Pro 8 for some time now, no problems whatsoever. Today I go out and by some expensive new monitors for my home studio I'm building, and of course of all days the Mbox is not working. I have tried reinstalling the Core Audio Manager, Reset the Permissions of the disk, tried two different USB cables, and tried 3 different computers. All of the lights are lit up on the Mbox, but I am getting nothing on the computers end.
Please help! I have a vocalist coming over to record in a few hours, and am excited to hear these new speakers! Thanks
What I have:
Macbook Pro running 10.5.6
Logic Pro 8
MBox (Original)
Thanks

Hi,
Check to see if the cable is a cross over ethernet or badly wired.
To check if its cross over:
Hold the cable ends side by side with the tabs away and copper contacts top
If the green and orange pairs are reversed then its a cross over cable
In the USA the standard is 568B in Canada 568A (its just a coloring standard the wiring is the same in ether case)
If your cable doesn't match either 568B or 568A its a bad cable and only working accidentally.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Similar Messages

TS3899 I use 3 email accounts. All were maintained in separate in boxes.   After upgrading to iOS7.0.2, all emails are together in one inbox. How do I get them back to their own separate in box?

I use 3 email accounts. All were maintained in separate in boxes.   After upgrading to iOS7.0.2, all emails are together in one inbox. How do I get them back to their own separate in box?

You should be able to see them either way, just as you should have been before you upgraded.
If you are viewing the consolidated Inbox, you should see something like this near the top of the screen:
< Mailboxes All Inboxes      Edit
Click on the blue "< Mailboxes" to get to the list of separate Inboxes (plus maybe VIP and Flagged virtual mailboxes). Click on one of them to view that Inbox.
If that does not match what you see on your phone, let us know what you do see.

My Cannon MP830 stopped scanning and faxing. Printing is fine, all lights are on.What do I do?

My Cannon MP830 stopped scanning faxing. Printing is fine, all lights are on. What do I do?

Hi Cburns!
Welcome to the Canon Forums and thanks for posting!
So that the Community can help you better, we will need to know about any error messages you're seeing (either on your computer or your printer), and the Computer Operating System you're using (Windows XP/Vista/7/8 or Mac 10.x), as well as the way you connect to your printer (USB or networked via WiFi or Ethernet).
Any other details you'd like to give will only help the Community better understand your issue!
If this is an urgent support need, please CLICK HERE to reach our friendly Technical Support Team by phone or email.
Thanks and have a great day!

Ideapad u310 is not powering up - all lights are blinking

Hi, i got a u310 that is not starting. Not only not booting, but not powering up at all. Plugged or unplugged the result is the same. All lights are blinking when i press the power or novo button(power button, power led, battery led and caps lock light, all white). They all blink together each 5 seconds and i hear a small click, like it's trying to power on or something. I can however press the power button again for a couple of seconds to turn it off.
The battery led blinks only when it is unplugged. When it is plugged, the battery light stay on(solid, white).
Anyone can help ? I've looked through the forum and could'nt find anything about this.
Thanks in advance

1. Remove any peripherals connected to the laptop.
2. Remove any power strips and surge protectors.
3. Remove the battery.
4. Press and hold the power button for 5 seconds.
5. Install the battery back and try to power ON.
6. Connect the charger and try to power ON.

HP Officejet 7000 Wide Format Printer Series Error "ALL LIGHTS ARE BLINKING?"

What are the causes of my printer HP Officejet 7000 Wide Format had this error "all lights blinking"? Which part of my printer have a problem? please help!! thankzzzz......

Hello ryigo24,
Welcome to the HP Forums.
I see that you are having an issue with all the lights blinking on the printer.
Please click on the following link that deals with Blinking Lights.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

Problem with WRT54G. All lights are Blinking

I do not know very much about technology and my router stopped working correctly. Now, the lights of Power, Internet, and the ones of the numbers 1 and 3 are blinking and the wireless connection does not work. Can anyone explain me what to do to solve this? I will be very grateful. Javier

hi... power cycle the n/w by unplugging power cable of modem and router, by unplugging power cable of modem and router...wait for couple of minutes, power up the modem first and once modem is rebooted power up the router, check whether lights stopped blinking or not, if lights are still blinking in that case you may need to reset the router back to factory default settings by pressing reset button on the back panel of the router but before you can reset the router let me know which internet connection are you using...so that i can tell you step by step configuration of the router...

Ipod touch - lights are on but nobody is home!

I (like many others) can not access my iPod. I've uninstalled, re-installed, connected, disconnected, tried installing a previous version but still my iPod fails to work. iTunes will recognize the initial connection telling me to connect for restore but it continually fails - gets about 1/3rd of the way then sits dormant.
Everything was spot on & working fine until sunday when I connected up and allowed an itunes update to proceed.
I know iTunes works - it still accesses my library on the Home PC but my iPod is inoperable.
If you have an answer please share it.... if there is an Apple/iTunes IT guru scouring these pages - please help! let us all know what has happened & when or even IF there is a fix for this.
I want to know if my ipod Touch is dead or is it just in a Coma?
p.s. - I've tried all the above actions on both my home pc windows XP & my laptop windows 7.

Yeeee I can't work my ipod either. I was on iBeer and then it told me my ipod wasnt sophisticated enough or something like that and told me to turn my ipod off. So I did, and now no more ipod for me.

Wrt54g only have 2 wireless put of 4 but all lights are on

I was having a connection problem the other day which was weird. So, I went to check on my wireless router and ALL 4 lights were lit. I unplugged it and rebooted and every thing went back to normal. Now it has happened again. Are people using my wireless connection?? Or is my box DYING? If I have my location set a home does that mean they can access my computer?? I have one thing hard wired and a wireless card in my laptop. I had set up a password with my router before, but maybe it got erased when I upgraded to a new laptop..?? I'm not sure if that could change it but I haven't deleted it my self. I'm not sure how to make sure that its there.. I found where it says WEP ..... and key 1. Also, I have SSID to something other then linksys. My network type is access point and network availability is All users (not sure what that means). How can I make sure I'm password protected?? ARGH! My head hurts! any info would be awesome!

So,all the four Ethernet light lit-up although only one computer is connected....Try to hard-reset the router for 60 seconds,Power Cycle the router and check the status of the light on the router.
If the light status on the router is OK then,open the router setup page by typing 192.168.1.1 and re-configure the router..If you get the same result after resetting the router then,try to upgrade the router's firmware..
You can download the firmware from www.linksys.com/downloads..On the linksys setup page,Click on Administration tab to upgrade the firmware..

All events are gone except one

All my pictures are in one event folder and all my old event folders are gone. I do not how this happened. Perhaps my daughter played with it. Does anybody know how I can get back my events?
Is there a kind of memory function? Thanks for your help.

Events menu: Autosplit Selected Event or restore from your back up
Regards
TD

7914 Expansion module - all lights are solid red

Hi,
I am trying to get an expasion module 7914 to work with my 7960.
These are some extracts from my config:
CONFIG (Version=4.0(1))
=====================
Version 4.0(1)
Cisco CallManager Express
load 7914 S00104000100
load 7960-7940 P0030702T023
At the moment when I go into the ephone with the expansion module, I can NOT enter the "add-on 1 7914" command. It is simply not available and not listed when I do a "show a?" command under the ephone
It seems to me that I am using the correct firmware but I can't get the expansion module to do anything. It simply sits there with a blank screen and all the buttons lighted in solid red.
The 7960 attached to it is working properly.
Any ideas why this is happening?
Thank you

I am responding because we also had difficulty getting our two 7914 expansion modules to work with our 7960.
I'm not sure I understand your problem with configuring the ephone. Are you using a telnet into the CME gateway and the CLI (Command Line Interface). I would do it that way, not through any kind of browser or GUI.
You will need to log in in enable mode and then
CME# config t
CME# ephone
CME# type 7960 addon 1 7914
Hope this helps some... Try TAC if all else fails.

WRH54G ALL LIGHTS ARE BLINKING WHAT SHOULD I DO?

Hi,
All the lights of my router are all blinking and the light of the ethernet on my modem is dead everytime i plug in my router but if i directly connect my dsl modem to my computer its working. any help on this thanks.

Reset the router to defaults. If that doesn't work, try this procedure.

All reports are seen in one webtemplate in bi 7

Hi Friends,
I have worked in web application designer , I have see the (all modules like pp,sd,mm,qm)all reports in one web template , it is possibe in bi 7 version , how it is possible.
plz tell me the step wise.

Hi,
Goto SPRO>SAP NEtweaver> BI>Settings for reporting and analysis>Bex Web>Execute Standard web templates> give ur webtemplate name here under Adhoc Analysis... so that it will accept for all of ur reports in BI. i dont abt SD, MM reports.
Thanks
Ajay

ThinkPad T410 - Powers up, no display, WWAN light lit, lights are on but nobody's home...

Hi, had to sign up today as this has stumped me, my T410 has decided to stop working, prior to it deciding to not work I was doing some Windows Updates, it asked to reboot, laptop shut down, powered up, and that was that, stuck with a blank screen and no signs it's going any further. Took a look around the web and the closest I came to the symptoms (pretty much identical, but lacking my own observations) being discussed is here: https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T410-won-t-boot-blank-screen-and-keyboard-unresponsive-at-power/m-p/1838638 Only there was no solution to the issue aside from the person sending it off for repair, which I don't want to do considering I'm a laptop repair technician by trade (so no need for baby-steps, I can take full-on techy speak)!! I've reseated as much as I can (RAM, HDD, ODD, WiFi & WWAN cards, CPU, even the 56k Modem!!), pulled the power when on, disconnected the CMOS battery, done the power button 10-presses & hold for 30 seconds thing, all to no avail. The things it does do are the LEDs go through their own POST on powerup, the WWAN LED remains lit whether or not the card's fitted, the CPU warms up as though it's trying to do something and as such the heatsink fan spins up when up to temperature, and when I press the power button again for about a second (asI would to to switch it off when in Windows), the HDD LED lights up, then goes out, then the laptop beeps and shuts off. So, considering it can switch itself off, there's some life there, but obviously something's gone south with the BIOS, whether it has something to do with Windows Updates or not I don't know, but it is a very strong coincidence that it broke down right after installing them. Any ideas? Or am I going to be stuck using my T61 again 'til I can replace or repair my T410? Thanks in advance...

Anything? Would like to get my laptop back up and running as soon as possible, feeling somewhat left out of the windows 10 loop here (I have it reserved for that laptop!!).

The lights are on but nobody is home

ok so i booted up my iBook the other day to find this problem, all the spiffy lights come on and i get the chime, the screen is lit up but nothing really happens.. i leave it for a while and i get an icon in the middle of the screen. I've tried the OS X discs but they spin up but don't boot.
http://www.monkey-junkie.com/stuff/DSC01020.JPG
that's a piccy of the icon. Any ideas on what is wrong and what is my next action?
Thanks

Papayafreak:
Command, Option, P, and R is the correct combination. Sorry
However, I am glad that you heard the chimes.
which did make it chime again and holding option made it go to a page with a refresh buttons and a next button, neither of which did anything.
If not boot volume icons appeared on the screen, it means that your boot volume is too badly corrupted to boot the computer. It may even indicate that you HDD is failing.
the disc doesn't boot up when i try, just the same thing.
You noted the above in an earlier post. Did you mean that you are unable to boot from the install disk or the internal HDD? If you are able to boot from the install disk, I would suggest trying to Repair Disk. If you are not able to boot from the install disk try the procedure outlined in the article Resolve startup issues and perform disk maintenance with Disk Utility and fsck.
In addition, if you do not have an up-to-date backup, we need to take care of that before proceeding much further.
Good luck.
cornelius

Lights Are On, But Nobody Is Home!

Incredibly frustrating ... After rebooting my internet, I can't get the internet Ethernet plug to work. I know my internet modem is working. I can get the internet via an Ethernet directly to the modem. When I plug the same Ethernet cable (that worked when connected to my computer), the Linksys EA4500 "Internet" plug doesn't light up!
I've tried resetting the Linksys (keeping the reset button down for 30 seconds, then unplugging the power cable while still keeping the reset button down for 30 seconds, then plugging the power cable back in while keeping the reset button down). During the whole time, the light indicator never flashed.
How do I fix this problem?

Hi,
Check to see if the cable is a cross over ethernet or badly wired.
To check if its cross over:
Hold the cable ends side by side with the tabs away and copper contacts top
If the green and orange pairs are reversed then its a cross over cable
In the USA the standard is 568B in Canada 568A (its just a coloring standard the wiring is the same in ether case)
If your cable doesn't match either 568B or 568A its a bad cable and only working accidentally.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

MBox - All lights are on, no one is home

Similar Messages

Maybe you are looking for