MBP 5,3 75°C hot at 0% CPU load after SSD install
Hello, i decided to post my problem here because i have not found any help on other forums.
Two weeks ago i installed a Samsung 830 SSD with 256 GB using the Optibay SSD Kit from Hardwrk (http://hardwrk.com/en/ssd-hdd-adapter-kit-for-macbook-pro.html). The SSD sits where the HDD was beforce and the old 500 GB HDD sits in the Adapter from the Kit where the optical drive was.
After installing the hardware, everything worked fine; i (partially) cloned the HDD to the SSD and booted from it. Only the biggest User folders are left on the HDD. A couple of days later i noticed that the CPU temperature was between 75°C and 80°C in idle, with no processes causing CPU load. The fans are working and spinning with about 3000 rpm. I increased the fan speed to maximum with iStat Menus and the temperature lowered to about 58°C which was normal before installing the SSD. After about 10 minutes of maximum fan speed i set the fans back to normal and the temperature increased to 78°C again.
I tried a safe boot and there are no such problems, the CPU temperature is at 58°C in idle. So i booted in normal mode again and the temperature stayed at 58°C in idle. I shut down the MacBook and turned it on again in normal mode. The temperature increased to 80°C and stayed. I don't understand that behaviour.
The HDD is far away from the CPU so it doesn't affect heating, the SSD is more cold than hot. I don't know where this problem comes from. Has anybody noticed a similar behaviour after installing a SSD? If you need additional information i will provide these.
Hello and thank you for participating in this discussion,
as i am the starter of this thread, i want to tell you the story how i fixed this problem.
as you know the MacBook from Mid 2009 has TWO internal SATA ports, one for the optical drive and the other for storage devices such as HDD and SSD. Prior posting my problem here, i used this two ports as follows:
SATA connector 1 (where by default the optical drive is attached to):
here i placed the adapter cage from hardwrk (Link) and IN there i placed the old HDD, which was attached to SATA 2 before setting the MacBook up for SSD
SATA connector 2 (where by default the HDD is attached to; below the optical drive):
here i placed the new SSD
With this setup i did experience the problems with higher working temperature of the MacBook. After testing on software level, turning TRIM on or off had no effect to the high temperature, i decided to open up the MacBook another time. i checked all the wires and connectors, everything okay. Back turned on, same problem.
Then i decided to switch the devices. Means, SSD in adapter cage, HDD on the old place. Voila! Temperature problems are gone. Maybe you try this.
Hope it helps. Let me know!
Similar Messages
-
I7 cpu bug - hot with no cpu load
After a wakeup, CPU is getting up to 80 degrees celcius, fans 4k+ rpm, even though the terminal top report and istat pro say cpu = 5%
The only way to get the system back into happy normal land, it a full restart.
It defeats the entire purpose of going to sleep and waking up.
I've posted on this before, and the best suggestion was, don't plug the power in too soon.
I am still unsure if this is the precise cause, but further feedback welcome, my patience, of course, is endless...I did a bit more poking around and it seems that the cause was mdworkers, bldy spotlight again.
Apparently if it does not finish indexing the Time Machine disk it just keeps starting again, seemingly never ending repeat of cpu/heat. But no apparent crash load kind of thing.
So, I left the thing running and came back to a calm machine.
Now I have not yet had the heat issue again.
Good to know I think, mdworkers are your friends, but can put on the heat when you least expect it! -
Why does the left side of mbp 4.1 get abnormally hot? What's is the problem?
Hello Everyone:
The bottom of my 2008, 15" 4.1 mbp has always gotten very hot. lately however, it gets extremely hot. The other night, I fell asleep with it open, on my lap and it literally burned me and left a nice blister on my lap. I think the fans are working because in a recent update, I've forgotten which one, the fans did go on and I heard them. Is this kind of heat normal? What, if anything, should I be doing to ensure it's not going to burn itself out? Obviously I'm not going to put it on my lap again but it's never done that in the past. Any thoughts anyone?
Thanks in advance for your help. I can't do much internal work since I've recently suffered a small stroke-like issue that's paralyzed my arms and taken fine motot movement out of my hands. If it's easy work htough, I may be able to get one of my kids to give me a hand.
Help please?!??
CCOk Austin. I've downloaded iStat. I can barely see the writing but the app is totally interesting. If there's a way to enlarge it without having to use the 'control' function to zoom in on it, that would be great. Aside from that, it looks like it may well tell me what's happening to my system's temps. As for the overheating, what you said is very interesting. I may very well be blocking one of the fans. We shall see! Thanks and hopefully blocking one of the fans!
Talk to you tomorrow. Hopefully I'll have had a chance to review the stats by then. Take care!
CC -
My mid-2012 MacBook Pro has the fan constantly running. As soon as I turn it on. My MBP won't even be hot and the fan is running. How can I fix this?
If you are still under warranty and/or have AppleCare, call them. Let them deal w/it.
OOW try the following: http://support.apple.com/kb/HT1411 Apple Portables: Resetting the System Management Controller (SMC) -
My Hot Spot does not work after update to 6.0.1. Any suggestions?
Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal. -
My MacBook Pro is running very hot after lion install. Are there any hardware changes that will help? What can I do to get it back to normal?
I get the impression that most of the users on older hardware experiences similar temperature issues on Lion for a long time now. Awaiting for confirmation from the original poster.
In the meantime I'm just cautious with regards to pushing the machine to such extreme temps, since something tells me such behaviour which includes monitor flickering and the likes is nothing but abnormal for any type of use...
Any clues if 10.7.5 does anything on this? If not I'm afraid i see myself going back to SL for good... -
New ssd install in MBP 5,3 (mid 2009 model)
Hello,
New to ssd installing and terminology used in some of the discussion forums I have been reading!
About to install my new ssd and have a few questions before starting. (ssd is a crucial M500 480gb)
I'll try to be a blunt as I can because I tend to ramble on.......
1. Do I upgrade/downgrade efi? (Read in other discussions)
2. Do I enable/disable trim? (Read in other discussions)
3. I am currently running 10.6.8 and wanted to purchase the newest OS possible to install. I've read of a few issues of ML and the battery drain issues. Is it best to just stay with my 10.6.8 for now?
4. I also purchased an 8gb ram upgrade over the current 4gb ram to do at the same time. Don't I have to reset something once I power the MBP back up to recognize the ram?
5. I purchased an external case to put the (currently in the computer) hdd in once I take it out. I planned on installing the ssd, putting the current hdd in the case, and migrating only my contacts, iTunes library, iPhoto library, and my flip videos from it. I have the original install disc from my MBP-can't I just install it onto the ssd from the DVD drive? (I hear of people installing the OS from USB-is there any disadvantage/advantage to this over my install disc?). I'm just wondering if it will give me the option of installing from the DVD drive once the ssd is installed and blank. ??
6. Is there anything else I should consider migrating to my new ssd?
I think that's it. Thanks!!This maybe too late, but here it goes:
1. Do I upgrade/downgrade efi?
- do not mess about with that. I have a mid 2009 MacBook Pro and am running 2x SSD drives inside without a problem. Only look in to EFI upgrading if the Negotiated Link Speed in System Information (Under Sata) is not reported as 3 Gigabit but rather as 1.5, once you install the SSD
2. Do I enable/disable trim? (Read in other discussions)
- some people report advantage from trim being enabled. I've personally noticed lockups during shutdown so keep it off. Typical SSD these days have grabage collection, but it is up to you in the end of the day.
3. I am currently running 10.6.8 and wanted to purchase the newest OS possible to install.
- don't purchase anything and download Mavericks for free, battery life will improve
4. I also purchased an 8gb ram upgrade over the current 4gb ram to do at the same time. Don't I have to reset something once I power the MBP back up to recognize the ram?
- the mac will recognise the ram anyway. You should however rest SMC see: http://support.apple.com/kb/HT3964
5. I purchased an external case to put the (currently in the computer) hdd in once I take it out. I planned on installing the ssd, putting the current hdd in the case, and migrating only my contacts, iTunes library, iPhoto library, and my flip videos from it. I have the original install disc from my MBP-can't I just install it onto the ssd from the DVD drive? (I hear of people installing the OS from USB-is there any disadvantage/advantage to this over my install disc?). I'm just wondering if it will give me the option of installing from the DVD drive once the ssd is installed and blank. ??
- yes by inserting the Disk in to the optical drive and holding 'C' during startup wil take you to the boot options, where you can format the SSD drive and install the OS
- advantage of OS on USB is faster install (quicker read speed) and for those people like me who substituted the optical drive for another HDD or SSD.
6. Is there anything else I should consider migrating to my new ssd?
- depending on your previous HDD size (and file sizes - looks like you have lots of photos and videos), make sure you watch what files you are bringing over as you can quickly run out of space on the SSD. You can use OmniDiskSweeper for example, to tell you wat files on your disk use the most space etc.
Hope this helps. And I am sure someone else will come up withh more suggestions -
MBP 2012 still slow after clean install of Yosemite
Hello,
I'm hoping someone can help me, I've done just about everything I can find online to get my MBP to work like it used to. After unsuccessful attempts at different workarounds, I decided to wipe everything perform a clean install of Yosemite.
Still no luck!! #nobueno
Problem description:
After clean install of Yosemite, my MacBook Pro (2012) continues to run at a snailspace. Very slow!
EtreCheck version: 2.1.8 (121)
Report generated February 18, 2015 at 11:51:42 AM PST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook Pro (13-inch, Mid 2012) (Technical Specifications)
MacBook Pro - model: MacBookPro9,2
1 2.9 GHz Intel Core i7 CPU: 2-core
8 GB RAM Upgradeable
BANK 0/DIMM0
4 GB DDR3 1600 MHz ok
BANK 1/DIMM0
4 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 294
Video Information: ℹ️
Intel HD Graphics 4000
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.2 (14C109) - Time since boot: 1:41:54
Disk Information: ℹ️
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 748.93 GB (735.33 GB free)
Core Storage: disk0s2 749.30 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
Default Browser: Version: 600 - SDK 10.10
QuickTime Plugin: Version: 7.7.3
3rd Party Preference Panes: ℹ️
None
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
4% WindowServer
1% Finder
1% mds
1% mds_stores
0% deleted
Top Processes by Memory: ℹ️
163 MB mds_stores
86 MB com.apple.WebKit.WebContent
77 MB Finder
69 MB WindowServer
52 MB mds
Virtual Memory Information: ℹ️
4.90 GB Free RAM
1.86 GB Active RAM
868 MB Inactive RAM
954 MB Wired RAM
2.28 GB Page-ins
0 B Page-outs
Diagnostics Information: ℹ️
Feb 18, 2015, 10:03:37 AM Self test - passed
Feb 18, 2015, 09:55:07 AM /Library/Logs/DiagnosticReports/mbpluginhost_2015-02-18-095507_[redacted].crash1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1248 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1000 150 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile AirPort 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:per sec:ms/s:KiB/s:%:total:MB:total' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' CFBundleIdentifier );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' %s{' ','\n'{"${k[22]}",}}'%s\n' '%d MB: %s\n' '\n ...and %s more line(s)\n' '\nContents of %s\n '"${k[22]}"'mod date: %s\n '"${k[22]}"'checksum: %s\n%s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS=":";if(system("sw_vers -productVersion|grep -q ^10\.1")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' { sub(/ :/,"");print|"tail -n'${p[10]}'";} ' ' NR==2&&$4<='${p[7]}' { print $4;} ' ' ($1~"wir"&&$2>'${p[22]}')||($1~/P.+ts:/&&$2>'${p[19]}') { print $1" "int($2);} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q":"$0":"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/, .+:/{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { print "/L.+/Scr.+/Templ.+\.app$";print "/L.+/Pri.+\.plugin$";if(NR<'{${p[14]},${p[21]}}') print "^/[Sp].+|'${k[21]}'";} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' BEGIN{ FS="= "} $2 { gsub(/[()"]/,"",$2);print $2;} ' ' /^\//!d;s/^.{5}//;s/ [^/]+\//: \//p;' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' BEGIN{FS=": "} /^ {10}O/ {exit} /^ {0,12}[^ ]/ {next} $1~"Ne"&&$2!~/^In/{print} $1~"Si" { split($2,a," ");if(a[1]-a[4]<'${p[5]}') print;};$1~"T"&&$2<'${p[20]}'{print};$1~"Se"&&$2!~"2"{print};' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS=":";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n "$5" => "$3" (UID "$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+5;i++)u[i]=u[2];split("'"${k[28]}"'",l,":");for(i in o) print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n '"${k[22]}"'"T;printf("'"${f[8]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[33]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/, .+:/||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/:/;s/(\n)c/\1:/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;p;' ' s/^.+ |\(.+\)$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/:(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}':/;s/ *: */:/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS=":"} { printf("'"${f[6]}"'",$1/1048576,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") D=D"\n"$1;} END { print D;} ' ' NR>1&&$3!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $3":"$2;} ' '|tail -n'${p[6]} ' $1>1 { $NF=$NF" x"$1;} /\*/ { if(!f) f="\n\t* Code injection";} { $1="";} 1;END { print f;} ' ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): .|d: Y/d;s/:$//;$d;p;' ' BEGIN { RS=",";FS=":";} $1~"name" { gsub("\"","",$2);print $2;} ' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' /^ +N.+: [1-9]/ { i++;} END { if(i) print "system: "i;} ' ' NF { print "'{admin,user}' "$NF;exit;} ' ' /se.+ =/,/[\}]/!d;/[=\}]/!p ' ' 3,4d;/^ +D|Of|Fu| [0B]/d;s/^ |:$//g;$!H;${ x;/:/p;} ' ' BEGIN { FS=": ";} NR==1 { sub(":","");h="\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;L[i]=l" "$2;if(i=='${p[24]}') nextfile;} END { if(i) print h;for(j=0;j<i;j++) print L[i-j];} ' ' /./H;${ x;s/\n//;s/\n/, /g;/,/p;} ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk 'dscl . -read' networksetup mdutil lsof test osascript\ -e netstat mdls route cat );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop {/,}L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|(allow|call)ing|(mplet|nabl)ed|ry HD|safe b|xpm' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA[(]|pagin|Purg(ed|in)|error|Refus|TCON|tim(ed? ?|ing )o|trig|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1:%@d:%s:%d\n\",@a);printa(\"2:%@d:%s:%d\n\",@b);printa(\"9:%@d:%s:%d:%s:%d\n\",@c);printa(\"10:%@d:%s:%d:%d\n\",@d);printa(\"11:%@d:%s:%d:%d\n\",@e);printa(\"12:%@d:%s:%d:%d\n\",@f);printa(\"3:%@d:%s:%d\n\",@g);printa(\"4:%@d:%s:%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{aut*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/{Lau,Sec}*/*t .launchd.conf" list '-F "" -k Sender hidd -k Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' print\ system --dns -get{dnsservers,info} dump-trust-settings\ {-s,-d,} -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[33]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[33]} :CFBundleDisplayName $EUID {,'/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s $TMPDIR../C -type f -size +'${p[11]}'M -exec stat -f'%z:%N' {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' 'L*/A*/Fi*/P*/*/a*.json' users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$(Sender): \$Message" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "[{}<>]|commit - no t|deprec|Goog|realp|sandbox ex|/root" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[33]}'=*"' -m\ / '' );N1=${#c2[@]};for j in {0..20};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console}\ log Activity SMC Login\ hook 'I/O per process' 'High file counts' UID Daemons Agents XPC\ cache Startup\ items {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ {caches/logs,overrides} Shutdown\ codes Heat Diagnostic\ reports Bad\ plists Free\ space VM Bundles{,' (new)'} Trust\ settings );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d$'\e' <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F$'\e' ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99; for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 32 70 101 25;D2 65 6 76 13;D2 45 20 52 66;D4 66 7 77 14;D4 17 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 77 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 25 22 20 32;D2 33 0 N1+14 51;for i in {0..2};do A1 29 35+i 104+i;B3 25+i;done;B6 25 27 5;B6 0 26 5;B4 0 0 110;C2 69;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 0 N1+20 43;B2&&D4 59 4 65 76 91;D4 63 4 19 44 75 95 96;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 12;D4 15 5 72 12;C4;};D4 16 5 73 12;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 50;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 18 31 107 94 74||{ B2&&A1 18 26 94 74;}&&{ B7 11;B4 0 0 11;C3 23;};A1 18 26 94;B7 11;B4 0 0 11;C3 24;D4 60 14 66 92;D4 58 14 67 93;D4 26 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 108; A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 109;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
Part 1 of 8 done at … sec
Part 8 of 8 done at … sec
The test results are on the Clipboard.
Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it and go to the next step. You'll have incomplete results, but still something.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Slow MBP after Yosemite install and other concerns
Hi
There are a few discussions on this topic, they did not help due to the fact that I have no clue what to do or if I even have a problem.
The problem:
My MBP is slower after I installed Yosemite, sometimes the wheel of death pops up and freezes what I am busy with in Safari. Apps take longer to open than usual.
I have added EtreCheck results from this morning.
Please give advice on:
How to improve the speed.
Whether there is there something in the results that I should be concerned about.
Hardware that should be updated.
Should I get an app to delete or prevent unnecessary files (from apps?) from being saved without my knowledge.
Thanks
EtreCheck version: 2.1.6 (109)
Report generated 26 January 2015 at 9:16:11 AM SAST
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
MacBook Pro Intel Core i7, 15" (Mid 2012)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 153
Video Information: ℹ️
Intel HD Graphics 4000
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Time since boot: 0:51:27
Disk Information: ℹ️
TOSHIBA MK5065GSXF disk0 : (500,11 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 498.88 GB (394.47 GB free)
Core Storage: disk0s2 499.25 GB Online
HL-DT-ST DVDRW GS31N
USB Information: ℹ️
Apple Computer, Inc. IR Receiver
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
User Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Support]
User Login Items: ℹ️
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.287 - SDK 10.6 [Support]
Flash Player: Version: 16.0.0.287 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 600 - SDK 10.10
3rd Party Preference Panes: ℹ️
Flash Player [Support]
Time Machine: ℹ️
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 498.88 GB Disk used: 104.41 GB
Destinations:
2TB Seagate [Local]
Total size: 2.00 TB
Total number of backups: 8
Oldest backup: 2014-10-16 21:41:16 +0000
Last backup: 2014-11-07 10:29:39 +0000
Size of backup disk: Excellent
Backup size 2.00 TB > (Disk size 498.88 GB X 3)
Top Processes by CPU: ℹ️
5% WindowServer
1% launchd
0% fontd
0% AppleSpell
0% ps
Top Processes by Memory: ℹ️
219 MB com.apple.WebKit.WebContent
176 MB Numbers
163 MB Finder
146 MB mds_stores
82 MB WindowServer
Virtual Memory Information: ℹ️
204 MB Free RAM
1.80 GB Active RAM
1.62 GB Inactive RAM
671 MB Wired RAM
1.99 GB Page-ins
532 KB Page-outs
Diagnostics Information: ℹ️
Jan 26, 2015, 08:25:19 AM Self test - passedHi epwebb,
The good news is that you have a good MBP. It seems to be hugged by that google crapware that you have on your Mac. They spy on you, use the bandwidth that you pay for and hugging your Mac obviously at your cost.
Your Mac should be motoring. Look here and here to get the Mac to perform as it should
Have fun
Leo -
I running snow leopard on my MBP- where can I find the drivers for windows XP if I install them via bootcamp? Thanks!
You won't find them until you are in Windows.
Helps to read even print the guide.
If you have auto run enabled, which is a security risk, the Apple setup.exe will run.
Otherwise, just run that.
Either use your OS X DVD, or use the drivers downloaded by Boot Camp Assistant.
Two different ways to get them. -
i hav installed mac os lion on my MBP 2011 model but it is telling me no wifi hard ware installed what do i do pls suggest me sumthing
so i cannot select my wifi or anything
please tell me what do i do
when i open network prefrences it shows
when i click on "turn on wifi" nothing happens
i have even done a apple hard ware test but it says everything is alright
i am really tensed what do i do pls help meIf AHT doesn't show any issues, your best bet would probably be to take it to the Apple Store. The AirPort (Wi-Fi) card may have been unseated from its original position. If there is a problem with the card Apple should be able to replace it for free.
-
Hot spot s not visible after latest iOS version update on my iPad please help
hey personal hot spot is not visible after iOS latest version update on my iPad mini please help
Hey Devinder from chd,
For most issues with Personal Hotspot, try out the basic troubleshooting in the article below. It does talk about iPhone but the troubleshooting is the same for your iPad. If you are still having issues, let me know and I can see what else we can do after that.
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/en-us/HT203302
Basic troubleshooting
See if your iOS device, computer, and wireless plan all meet the system requirements for Personal Hotspot.
Make sure Personal Hotspot is on: Tap Settings > Cellular > Personal Hotspot.
Check the Internet connection on your iOS device: Tap Safari and load a new webpage.
If one connection type doesn't work, try another. For example, instead of connecting using Wi-Fi, use USB or Bluetooth.
Turn Personal Hotspot off and on: Tap Settings > Personal Hotspot or Settings > Cellular > Personal Hotspot.
Install the latest version of iOS.
Reset your network settings: Tap Settings > General > Reset > Reset Network Settings.
If you still see the issue, restore the iPhone.
Take it easy,
-Norm G. -
My MacBook Pro gets really hot after I install OS X 10.10.3. Can Someone help?
After i install OS X 10.10.3 my macbook pro gets really hot. I don't know why. Someone has a solution?
Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. You may have to leave the machine there for several days.
Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional—ask if you need guidance.
If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present.
Keeping your confidential data secure during hardware repair
Apple also recommends that you deauthorize a device in the iTunes Store before having it serviced.
*An SSD doesn't need to be zeroed. -
MBP not displaying to external monitor at startup, but does after login
After I installed Yosemite my MBP will not automatically display to my external monitor (HDMI) when I start it up. I have to first login to my MBP and then my external monitor is immediately recognized and my mirroring desktops works as intended...as it did before I upgraded to Yosemite. I have no idea why the signal to my external monitor doesn't/will not work upon system start up. Anyone out there know??
Did you find a solution? I have the exact same problem. I just install Yosemite and did not have the problem before.
-
MBP doesn't see newly installed SSD (installed into optical drive bay)
Hi all,
Re-posting, from an earlier post, with a more specific topic. I recently installed an OWC 2.5" SSD, via the OWC Data Doubler, replacing my old, non-working, optical drive. I installed it step-by-step, from their installation video. BTW - I also installed a RAM upgrade, and, that installation (although admittedly easier than the SSD install) is working fine. However, my MBP is not "seeing" any new drive. Does anyone know if there is a step that I am missing? Or have an idea what I may have done wrong?
I re-opened the machine and double checked that all 3 "connections":
From SSD to Data Doubler Frame;
From Data Double Frame to SATA tab; and
SATA connector to the motherboard;
WERE ALL SEATED PROPERLY. Yet, the MBP still does NOT see the newly installed drive.
Any help would be greatly appreciated.
Thanks.
MJHi,
Have you tried booting up while holding down the Option key and the selecting the SSD? Or putting the SSD in the other bay?
Maybe you are looking for
-
I forgot the answers for the security questions and when I try to change them (My Apple ID -> Manage your account -> Password and Security) I'm asked to answer the exact questions I'm trying to change because I don't remember the answers. How can I d
-
Why can't I access the top portions of a website I'm visiting when using firefox?
I'll use facebook for an example, but bear in mind that this problem is when ever I go on any website. When I signed on facebook, my mouse turns into an arrow and it won't allow me to select anything on the top/upper portion of the website. I have to
-
I have created query on a cube,see cube is at aggregated level andso we may get multiple values for a char A and that is right for the reason of key fields value differ. How to avoid such kind of probs for characteristics. We know the option to avoid
-
How to play an audio file from the begin.........
Hello to everybody, I am working on a application that is supposed to manage audio file. At the moment I 'm using the SourceDataLine instead of the Clip. But I've got a problem. When the user pushes the Stop button I want that if he pushes Play again
-
No visibility of state central bank indicator (LZB-KZ) in invoice header
Hi all, in the help documentation for SRM 7.0 (SAP Library - Invoice Entry) is mentioned that the SCB field (LZB-KZ) can be made visible on the invoice header screen. Whether or not this field is visible depends on a country-specific BAdI. This BAdI