MBP Does Not Recognize External USB Devices
MBP does not "see" external USB devices (such as Garmin Nuvi GPS) or any thumb drive. No external USB devices show up in Finder nor does Disk Utility see them. No cable issues. Have tried restarting several times, but to no avail. This MBP used to recognize these USB devices, but no longer do so.
I have seen this question posed several times in forum, but no suitable answer. Don't know if it is H/W or S/W problem.
Hi Terry Temple
Is there at least any power going to the USB ports? ( as in if for example you plug in a USB light, will it switch on? )
If there is power in the USB ports it might be a software problem.
Try resetting the SMC see link: http://support.apple.com/kb/HT1411
also try re-set the PRAM see link: http://support.apple.com/kb/HT1379
However if you do not have any power at all it probably is a hardware problem.
Is it still under warranty?
Regards,
Andrew
Message was edited by: iddrew
Similar Messages
-
Macbook does not recognize external USB drive - except when booting with CD
Hi all,
I recently swapped my Macbook's internal HD (Toshiba 100gb 5400 rpm) into an external USB enclosure (Eagle Consus). The computer does not recognize the external HD, even when using two USB cables for extra power. No luck with safe mode or resetting PRAM. Disk utility just hangs with spinning wheel if I start it. Switching the USB ports does not help.
I thought it might be a power problem until I noted the following:
1)The external drive works fine if I boot the Macbook from the Mac OS install CD... with this I can run disk utility and scan the drive with no problem
2)It works fine on an old Mac Mini with only ONE of the USB connectors plugged in
3)The enclosure worked fine on the Macbook when I had the new drive in it (320 GB 7200 RPM) while copying the files over
Any thoughts?
Many thanks,
--TIt is actually using a power supply, yet it will not actually power on unless it is connected to a computer's USB port. At least this is how it works on my old desktop running Windows 2000. When you disconnect the drive from Windows, or put the machine in hibernate mode, the device actually shuts down. It powers back up once the machine wakes up from hibernate mode.
It's a somewhat older device which predates the Macbook Pro, but it claims to support older Mac, such as the G3, G4, G5, iMac, iBook. OSX 10.0.4. So perhaps it's just too old?
It's a Buffalo HD-HB250U2 (250 GB).
So you're in Japan too? -
When you load Windows via Boot Camp Assistant program and run Windows does not recognize the "usb" outlets cannot identify the device through the Dvd or flash
Did you install BC drivers on the Windows side?
-
ITunes 12.0.1.26 does not recognize my mobile devices.
iTunes 12.0.1.26 does not recognize my mobile devices.
Hello,
I have the same experience with my iPod Classic under 12.0.1.26 under Max OS X Yosemite 10.10.2. But on another Mac with OS X 10.7.5 and iTunes 12.0.1.26 it is recognized.
Regards
mhomscheidt -
Does not recognize bootable usb
My HP laptop does not recognize some bootable usb devices in the boot menu.
I have a HP tower and the laptop in my office and the tower will recognize and boot the a USB device that the laptop will not recognize in the boot menu.
Laptop: HP Pavilion dm1z-4100, BIOS HP vF.19 2/4/2013, Windows 7 Pro 64bit
Tower: HP HPE-480t, BIOS American Megatrends v6.10 9/16/2010, Windows 7 Pro 64bit
Example of non recognized device in laptop (OK in tower): USB HDD WD60 OUE-22 HCTO
The external HDD reacts the same as some memory sticks. All the boot devices appear to be syslinux bootable
I have never found a non recognized bootable device in the tower PC boot menu, but several in the laptop PC.
No problem with laptop using external CD/DVD drive
The problem appears to be in the BIOS, because the boot menu occurs prior to the operating system.
Latest BIOS listed in the updates is F.19 (same as installed)
Any comments?Hi lrclost,
Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your HP Pavilion dm1z-4100 Notebook and not recognize some bootable usb devices in the boot menu. Here is a link to secure boot.
This document will explain the differences in boots.
Hope this is helpful.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping! -
Macintosh: Flash Player does not recognize external webcam
Hi,
the Adobe Flashplayer does not recognize an external webcam on my iMac. When I open Settings and try to choose a camera, it offers:
DV Video
IIDC FirWire Video
USB Video Class Video
The last entry activates the built-in iSight camera, but not the Logitech Camera which is connected via USB. If I choose one of the other options, the picture freezes, but it does not activate the external Logitech cam.
The Computer recognizes the Logitech Cam alright, it works fine with other apps (Skype, iChat). Does anyone have an idea what can be the problem?
Webcam: Logitech Vision Pro USB für Mac, nagelneu
Computer: Intel Mac, OSX Tiger 10.4.?
Browser: Mozilla Firefox
Thanks for any help!I've been trying to work through similar problems, as have many other Mac users from what it looks like. Here's a quote from a post I found in Apple's forum:
My Logictech 9000 doesn't show up in the Flash video source dropdown for me either. Selecting USB camera just selects the iSight.
However, I did find a workaround: it seems to choose the first available usb webcam, which is typically the built-in iSight. If you have a mac mini with no built-in iSight, it uses the external camera by default. For my MacBook, I found the trick was to make the iSight busy by opening Photo Booth first, then opening the flash chat page. That causes the flash player to find and use the external USB webcam.
Note: your webcam probably has to support the new standard USB Video plug-and-play protocol for this to work, and perhaps only on Leopard.
Here's the link to the page where I found this post:
http://discussions.apple.com/thread.jspa?threadID=1374761
Hopefully this works for you if you haven't already found a solution - I see you posted back in April! I'm sorry that no one attempted to answer your question before now, including the Adobe people who staff these forums! -
Mac mini does not recognize external drive
I have an 80GB external drive full of music files. I disconnected my computer to move to a new house and, with everything re-connected, the mini does not recognize the external drive. I wonder whether it is because the internal drive is nearly full. I have tried restarting the computer, disconnecting and re-connecting the USB cable to the external drive, serching for it with the disk utility, un-pluggin the external drive power cable and re-connecting it, but I'm out of ideas. What might have happened?
DBG413 wrote:
Any suggestions on why my XP laptop cannot view the mac info on the HD.
you'll have to install e.g. MacDrive or HFS+ for Windows on your winsloth machine. -
Windows 8 Bootcamp Does Not Recognize External Monitor
So, my Bootcamp of Windows 8 does not recognize my external monitor when I try to plug it in. I have read that the startup must recognize the monitor during the boot process. However, I have already done this and my external monitor remains in sleep mode. My drivers are all up to date with this bootcamp and I work on programming a lot so I need a solution for this issue because going back and forth between windows of the internet and my code is not ideal for me and wastes too much time. The external monitor works when I run my OS X, just not on Windows 8. If anyone could point me in the direction of how to solve this issue, it would be greatfully appreciated.
They're downloadable. But I'm going to create a system restore point in case something happens.
The below discussion had a similar issue but with Windows 7
https://discussions.apple.com/message/12358950#12358950
http://www.nvidia.com/Download/index.aspx?lang=en-us -
My iMac does not recognize external hard drive
My iMac does not recognize my external hard drive. Disk utility recognizes it and a test of the hard drive does not review any error. I use the hard drive as a back up for the time machine. This problem comes and goes. It comes when I turn off and turn on the computer, with the hard drive attached.
Please help.
Insightfulcan be this reasons
01 , you have problem with connection ? check the port if you can find any problems physically .
02. if not try to change the cable and with connection ,
03. may be its good idea to check the hard drive with another mac ?(if you have )
Did you note any diference of sound from Hard Drive ? listen to it that carefully to note some unusual sound comes when the hard drive works.
check this link this might usefull: http://www.youtube.com/watch?v=JjgOSxKy-FQ -
Imac does not recognize my usb after installing mountain lion
My imac don´t recognize my usb after installing mountain lion, also don´t let me see all my photos in jpg format
What is "my USB"? If it's an external USB device, is it ML compatible?
Which app do you use to open JPGs? Is it ML compatible? -
FireWire does not recognize external drives anymore
FireWire devices are not recognized after using software upgrade. USB 2 still works but firewire port does not mount any external drives. How can I check if my MacBook Pro has a hardware or software problem? I appreciate any help.
Thought you could use this info about getting FireWire to work!
First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 30 minutes. plug it back in and try FW.
If that didn't work, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try.
If that still didn't get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release.
For those of you with Macs that are not PowerBooks or iBooks, a bad internal battery can cause FireWire to not be recognized, so make sure it's good! Also, here is Apple doc.#88338 on getting FireWire to work.
Here's another Fw Faq.
DALE -
HT201250 Time Machine does not recognize external drive at start up
I have an external WD 2TB drive which I use as my Time Machine back up drive. When I restart the iMac desktop the Time Machine drive does not start automatically and I must open Time Machine each time and remember to identify the external drive that contains my Time Machine back up data. Is there some way to make this drive the default Time Machine back up device when the system starts? It is annoying to have to remember to do this each time my machine restarts. I have a drive icon that displays as "My Book" on restart where the Time Machine icon is located but this icon is yellow and my Time Machine drive icon is blueish green. Once I set the correct drive it will go into the mode to refresh the backup (usually in 118 seconds) and then once the backup is updated then the icon become blueish green and all works normally. Please help! Thx Tom
I called Apple tech support and went through the recommended actions with doing the disk check with the Utilities and all checked out okay. They had to ask the senior support advisor and was told that it does not automatically start the Time Machine drive until the next scheduled back up. There was a misconception that this drive SHOULD be identified as the Time Machine drive on boot up but that is not the case. I waited for the next schedule back up after reboot and it DID recognize the drive and it appears to be working fine.
The Time Machine does start on boot up but does not indicate that the Time Machine is recognized until the back up is done then it is back on cycle and will operate normally until the next reboot where it will then refresh during that cycle and become recognized in green. Until that time the drive will appear as a yellow icon for the disk.
Oh, by the way, the drive has external power on my WD 2 TB drive. -
Photoshop 11 does not recognize external harddrive when trying to reconnect images?
I have moved my catalog to a new computer, using Photoshop Elements 11. All images are on 2 external harddrives. The PC recognizes both harddrives and shows folder structure and files correctly. When in Photoshop Organiser the thumbnails appear, with the question mark, as the drive structure is different to the old PC. When trying to reconnect the images to the second external harddrive Photoshop suddenly does not recognise this harddrive anymore.
Please anybody advise on what I can do to fix that?Please try steps mentioned on blog: http://psekb.blogspot.in/2013/03/how-do-i-reconnect-missing-files-in.html Let me know if it doesn't help.
~Andromeda -
Hwd -e does not list connected USB devices
USB devices for audio in/out not recognized in hwd -e.
Desired USB Items appear in KDE INFO CENTER: SOUND.
KDE MIXER alternate...USB Mixer... shows OUTPUT PCM icon but no INPUT device is shown (thus, no device is connected).
System has udev installed but uncertain whether root permission is provided for the USB devices...namely...USB MIXER and SND-USB.
Spent many hours in stupid search for ...audio group....and ...optical group...
when the reference name for the "group" is...audio devices... and ....optical devices... This is a common problem in searching out posts..improper nomenclature references.
A listing for ...mixer...is provided but none for ...usb mixer...
Can I assume that all entries in the udev permissions file permit immediate use by root? Do they have to be edited to function? The indications are that root owns them all and doesn't need permission.
Sure would like to get USB audio running!!!
Are there special requirements for the USB devices?Additional info:
Tried playing a CD track copied onto the desktop in XMMS. The display shows it responding in XMMS. There is no audio from the external USB sound device.
The mixer in KDe is set to USB Audio mixer (PCM). An output ICON appears but there is no INPUT icon( No source connected).
hwsetup -v -n follows:
root@n6re ~]# hwsetup -v -n
class: OTHER
bus: PCI
device: (null)
driver: via-agp
desc: VIA Technologies|VT8367 [KT266]
class: OTHER
bus: PCI
device: (null)
driver: unknown
desc: VIA Technologies|VT8367 [KT266 AGP]
class: OTHER
bus: PCI
device: (null)
driver: via-ircc
desc: VIA Technologies Inc|VT8233 PCI to ISA Bridge
class: OTHER
bus: PCI
device: (null)
driver: unknown
desc: VIA Technologies|VT82C586 IDE [Apollo]
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Linux 2.6.9-ARCH ehci_hcd VIA Technologies, Inc. USB 2.0
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Linux 2.6.9-ARCH uhci_hcd VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1Controller
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Linux 2.6.9-ARCH uhci_hcd VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1Controller (#2)
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Linux 2.6.9-ARCH uhci_hcd VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1Controller (#3)
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Linux 2.6.9-ARCH uhci_hcd VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1Controller (#4)
class: OTHER
bus: USB
device: (null)
driver: keybdev
desc: Silitek IBM USB HUB KEYBOARD
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: Silitek IBM USB HUB KEYBOARD
class: OTHER
bus: USB
device: (null)
driver: audio
desc: USB Audio
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: USB Audio
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: unknown
class: OTHER
bus: USB
device: (null)
driver: unknown
desc: unknown
class: NETWORK
bus: PCI
device: eth
driver: ne2k-pci
desc: Realtek|RTL-8029(AS)
class: MOUSE
bus: USB
device: input/mice
driver: mousedev
desc: Logitech USB-PS/2 Optical Mouse
class: MOUSE
bus: PSAUX
device: psaux
driver: msintellips/2
desc: Generic PS/2 Wheel Mouse
class: AUDIO
bus: PCI
device: (null)
driver: snd-cmipci
desc: C-Media Electronics Inc|CM8738
class: AUDIO
bus: USB
device: (null)
driver: audio
desc: USB Audio
class: AUDIO
bus: USB
device: (null)
driver: audio
desc: USB Audio
class: CDROM
bus: IDE
device: hdc
driver: ignore
desc: SONY DVD RW DRU-530A
class: CDROM
bus: IDE
device: hdd
driver: ignore
desc: SONY CD-RW CRX320E
class: VIDEO
bus: PCI
device: (null)
driver: Card:ATI Radeon (fglrx)
desc: ATI|Radeon 8500 QL (AGP)
class: FLOPPY
bus: UNKNOWN
device: fd0
driver: unknown
desc: 3.5" 1.44MB floppy drive
class: HD
bus: IDE
device: hda
driver: ignore
desc: Maxtor 6Y080L0
class: KEYBOARD
bus: USB
device: (null)
driver: keybdev
desc: Silitek IBM USB HUB KEYBOARD
class: USB
bus: PCI
device: (null)
driver: usb-uhci
desc: VIA Technologies|VT82C586B USB
class: USB
bus: PCI
device: (null)
driver: usb-uhci
desc: VIA Technologies|VT82C586B USB
class: USB
bus: PCI
device: (null)
driver: usb-uhci
desc: VIA Technologies|VT82C586B USB
class: USB
bus: PCI
device: (null)
driver: usb-uhci
desc: VIA Technologies|VT82C586B USB
class: USB
bus: PCI
device: (null)
driver: ehci-hcd
desc: VIA Technologies Inc|VT8235 USB Enhanced Controller
class: UNKNOWN
bus: PCI
device: (null)
driver: ohci1394
desc: Texas Instruments|TSB43AB21 IEEE-1394 Controller (PHY/Link) 1394a-2000
[root@n6re ~]# -
MBPr does not recognize Samson USB microphone.
I've been using a Samson GoMic USB for several months. Just today the MBPr has stopped responding to it. I can see the mic under <Sound>, I can select it as the input device, but it does not register any sound input. Works fine on two other macs. Build 12D78, osX 10.8.3 Any tips?
ThanksCheck your settings in the Audio Midi Setup app which is located inside your Utilities folder.
Maybe you are looking for
-
Hi All, I am using the following queries in formula columns of a 6i report. The query count for these queries as seen from the trc file is very high, which is causing performance issues in the report. Can anyone please help me to tune these queries.
-
Strange Facet of Imported Graphic: ò\e2
Hello Framers, I am using Frame 7.1 and have just taken over a project from a colleague who is sometimes, er, careless with best practices. So I MIF-washed all files (replacing all OLE2 graphics) and tried to save as RTF. Frame crashed. I looked at t
-
When I click on emails in the inbox of one of my email addresses, nothing is displayed (or in the case of one of them, a large block of characters is displayed, like this "C+Z3dc7paG+d3jJtavOUpob6ulqppnp"). This only affects emails up until the last
-
I am creating internal corporate training videos... relatively easy items, I don't expect to see them on TV or even in the movie theaters... but I do expect to distribute the results via the web and iPods. My arsenal includes a Sony HVR-Z5U with HVR-
-
Hi I have the following PL/SQL code. type temp_atlanta is table of atlanta_operator%rowtype index by binary_integer; atlanta_1 temp_atlanta; begin select * bulk collect into atlanta_1 from atlanta_operator; forall k in 1..atlanta_1.count insert into