MDS Zoning and 1 Active Zoneset

I had a question regarding the statement that on a single MDS 9148 for example, only one Zone Set can be active. However, isn't it also true that if I have 2 VSANs 3 and 5 defined on this single MDS, I can have 2 active zone sets (1 per vsan) correct?
Thanks

Hello
Yes, you are 100% correct.  One active per VSAN
Steven

Similar Messages

  • Misconfigured zoning and had to bounce ports, can someone explain?

    I am working in a lab, and had the following configuration:
    HOST1-PORT1 connected to MDS1 in VSAN10
    HOST2-PORT1 connected to MDS2 in VSAN 20
    DISK1-PORT2 connected to MDS2 in VSAN10
    DISK2-PORT2 connected to MDS1 in VSAN 20
    MDS1 and MDS2 were connected via a FCIP tunnel.
    I could see everything as expected in the fcns database. What I wanted to do was have HOST1 use DISK1 from over the FCIP tunnel and HOST2 use DISK2 over the FCIP tunnel.
    What I accidently did, was zone as follows:
    Zone10
    HOST1 DISK1
    Zone20
    HOST2 DISK1
    From HOST1 I could not see DISK1 (windows disk manager), I could see it from HOST2 however, was able to format it and work with it. Once I figured out that I had zoned that drive to two hosts, I immediately went to correct it. And by the way, Sansurfer on HOST1 did show it saw the drive, but windows disk tools did not see it.
    So on the MDS, I removed the incorrect pwwn, added the correct one, and activated the zoneset. Still HOST1 could not see the drive. HOST2 however could now see its new (corrected) drive. HOST2's sansurfer topology map was actually still showing both PWWN's, not sure if that was just cached or not as the DISK1 was no longer zoned to it.
    So I reboot each HOST. Still no go, HOST1 could not see the DISK1! BTW, I checked the active zoneset and MDS reported all members correct and visible. So then I bounced each VSAN......honestly because I wasn't sure what else to do, and that still did not fix the issue, I tried to tell the disk management to rediscover drives but to no avail. Finally, came the sledgehammer. I bounced the actual FC ports. This fixed the problem.
    My question is, is this normal behavior? I thought when I rebooted the windows hosts, it would cause them to do FLOGI again which I thought would be same as bouncing the FC ports. Did bouncing the host ports have anything to do with this resolution? Or was it the bouncing of the DISK ports that was the fix? What situation did I get myself into that the drive could not be seen by windows even though it was zoned to it?

    I have seen Windows OS do some weird things like this. I have had to reboot the system when the HBA config tool saw the FC attached luns and they looked just fine in the tool, but Disk Manager would not pick them up.
    I have traced, as Inch suggested, with a PAA-2 and MDS span, and issued a re-scan on the Windows Disk Manager panel...and the trace show nothing being sent by the port the Windows box was plugged into. I had to bounce the port on the MDS and I saw the Windows box issue all the normal bring up stuff and register with the FC nameserver...then it got all the devices in teh zone...then I expected a PLOGI from the HBA to the storage device....nothing.
    That's when I rebooted and the trace showed the Windows box finally issue the PLOGI and PRLI to the storage device.
    Bottom line, when I make changes to zoning for a Windows environment, I reboot.
    Linux and Solaris seem to handle zone changes better. As for AIX 5.3...let's not go there :)
    My 2 cents,
    Mike

  • Communication between MDS C9134 and C9222i

    Dear Support,
    need your help to fix my setting.
    I have bought now the good 10GBFC Module for connexion between MDS C9134 and C9222i. the trunking is OK between the 2 switches.
    But we have Vsan with zone on each MDS but they cannot communicate.
    Please find in attach my setting.
    Waiting for your feedback urgently
    Best Regards

    Hello Omer,
    Yes, you got it right, LANs are very different from SANs. VLAN concept is similar to VSAN, but there are a few differences. First of all, there is no concept of LAN's VTP in Cisco's SAN-OS (NX-OS). You need to manually create VSANs on all switches. Secondly, "inter VSAN routing (IVR)" is not automatic. You have to configure IVR vsan-topology and IVR zones+zoneset. But in your case, maybe you could just put all devices into the same VSAN and simply control communication between devices using zones. Yes, you could use only VSAN 1 to solve it. Place everything into VSAN 1 and configure zones in VSAN 1 on one of the switches. Place zones into zoneset, activate it, and active zoneset will automatically propagate in VSAN 1 to the other switch.
    Let me know if you have any more questions.
    Regards,
    Roman

  • Activating zoneset only from the core switch

    Folks,
                How can i restrict so that only the core switch is allowed to make changes to the active zoneset?
    Also if I am merging two switches and they have active zonesets but with different names, would that merge the two fabrics?
    Thanks,
    Tarun

    your probably thinking about NPV, NPV is disruptive but NPIV isn't. It is just a feature that you would enable on the core.
    The acronyms are confusing and easily mixed up.
    NPIV allows multiple initiators to login over a single FC/port-channel. NPV changes the operation of the switch so that to the core it looks like a host with a lot of initiators/HBAs. In NPV mode the edge switch doesn't consume any FC domain IDs.
    Here is a link that should be helpful - http://www.cisco.com/en/US/prod/collateral/ps4159/ps6409/ps5989/ps9898/white_paper_c11-459263.html

  • Mds-soa and mds-owsm

    Dear all,
    I apologize for this basic question.
    I just finished the installation of the SOA suite, and when I try to access the mds-soa and mds-owsm metadata repositories from the EM, I get an ORA-00942 error, which I get as well when I start the soa_server1 server.
    I executed RCU and the soa installation produced no errors.
    Any help of pointers will be greatly appreciated.
    Regards

    for me this is the error :
    [2009-10-26T04:55:19.703-04:30] [AdminServer] [ERROR] [] [RepositoryPartitionsModel.class] [tid: [ACTIVE].ExecuteThread: '12' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: weblogic] [ecid: 0000IIGAVORFKA05zzXBiW1AsO7X0000H0,0] [APP: em] Getting partitions
    [2009-10-26T04:55:22.125-04:30] [AdminServer] [ERROR] [] [oracle.mds] [tid: [ACTIVE].ExecuteThread: '12' for queue: 'weblogic.kernel.Default (self-tuning)'] [userId: weblogic] [ecid: 0000IIGAVORFKA05zzXBiW1AsO7X0000H0,0] [[
    oracle.mds.internal.persistence.db.fcf.MDSDBIOException: ORA-00942: Table ou vue inexistante
         at oracle.mds.internal.persistence.db.fcf.FailoverUtils.executeQuery(FailoverUtils.java:159)
         at oracle.mds.persistence.stores.db.AbstractDBMetadataRepository.getAllPartitionNames(AbstractDBMetadataRepository.java:323)
         at oracle.mds.internal.lcm.domain.MDSRepository.getPartitions(MDSRepository.java:181)
         at oracle.mds.internal.lcm.domain.MDSRepository.getPartitions(MDSRepository.java:159)
         at oracle.mds.internal.lcm.mbean.MDSDomainRuntimeMBeanImpl.listPartitions(MDSDomainRuntimeMBeanImpl.java:289)
         at sun.reflect.GeneratedMethodAccessor2493.invoke(Unknown Source)
         at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
         at java.lang.reflect.Method.invoke(Method.java:597)
         at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.doInvoke(OracleStandardEmitterMBean.java:876)
         at oracle.as.jmx.framework.generic.spi.interceptors.ContextClassLoaderMBeanInterceptor.internalInvoke(ContextClassLoaderMBeanInterceptor.java:94)
         at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:245)
         at oracle.as.jmx.framework.generic.spi.interceptors.MBeanRestartInterceptor.internalInvoke(MBeanRestartInterceptor.java:116)
         at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:245)
         at oracle.as.jmx.framework.generic.spi.security.AbstractMBeanSecurityInterceptor.internalInvoke(AbstractMBeanSecurityInterceptor.java:174)
         at oracle.as.jmx.framework.generic.spi.interceptors.AbstractMBeanInterceptor.doInvoke(AbstractMBeanInterceptor.java:245)
         at oracle.as.jmx.framework.standardmbeans.spi.OracleStandardEmitterMBean.invoke(OracleStandardEmitterMBean.java:790)
         at com.sun.jmx.interceptor.DefaultMBeanServerInterceptor.invoke(DefaultMBeanServerInterceptor.java:836)
         at com.sun.jmx.mbeanserver.JmxMBeanServer.invoke(JmxMBeanServer.java:761)
         at weblogic.management.mbeanservers.domainruntime.internal.FederatedMBeanServerInterceptor.invoke(FederatedMBeanServerInterceptor.java:349)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
         at java.security.AccessController.doPrivileged(Native Method)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
         at weblogic.management.mbeanservers.internal.JMXContextInterceptor.invoke(JMXContextInterceptor.java:268)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
         at java.security.AccessController.doPrivileged(Native Method)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
         at weblogic.management.mbeanservers.internal.SecurityMBeanMgmtOpsInterceptor.invoke(SecurityMBeanMgmtOpsInterceptor.java:65)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase$16.run(WLSMBeanServerInterceptorBase.java:449)
         at java.security.AccessController.doPrivileged(Native Method)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServerInterceptorBase.invoke(WLSMBeanServerInterceptorBase.java:447)
         at weblogic.management.mbeanservers.internal.SecurityInterceptor.invoke(SecurityInterceptor.java:443)
         at weblogic.management.jmx.mbeanserver.WLSMBeanServer.invoke(WLSMBeanServer.java:314)
         at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11$1.run(JMXConnectorSubjectForwarder.java:663)
         at java.security.AccessController.doPrivileged(Native Method)
         at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder$11.run(JMXConnectorSubjectForwarder.java:661)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
         at weblogic.management.mbeanservers.internal.JMXConnectorSubjectForwarder.invoke(JMXConnectorSubjectForwarder.java:654)
         at javax.management.remote.rmi.RMIConnectionImpl.doOperation(RMIConnectionImpl.java:1426)
         at javax.management.remote.rmi.RMIConnectionImpl.access$200(RMIConnectionImpl.java:72)
         at javax.management.remote.rmi.RMIConnectionImpl$PrivilegedOperation.run(RMIConnectionImpl.java:1264)
         at java.security.AccessController.doPrivileged(Native Method)
         at javax.management.remote.rmi.RMIConnectionImpl.doPrivilegedOperation(RMIConnectionImpl.java:1366)
         at javax.management.remote.rmi.RMIConnectionImpl.invoke(RMIConnectionImpl.java:788)
         at javax.management.remote.rmi.RMIConnectionImpl_WLSkel.invoke(Unknown Source)
         at weblogic.rmi.internal.ServerRequest.sendReceive(ServerRequest.java:174)
         at weblogic.rmi.internal.BasicRemoteRef.invoke(BasicRemoteRef.java:222)
         at javax.management.remote.rmi.RMIConnectionImpl_1031_WLStub.invoke(Unknown Source)
         at javax.management.remote.rmi.RMIConnector$RemoteMBeanServerConnection.invoke(RMIConnector.java:978)
         at weblogic.management.remote.wlx.ClientProvider$WLXMBeanServerConnectionWrapper.invoke(ClientProvider.java:291)
         at weblogic.management.remote.wlx.ClientProvider$WLXMBeanServerConnectionWrapper.invoke(ClientProvider.java:291)
         at oracle.sysman.emai.model.mds.util.WLSTopologyHelper.getPartitionsList(WLSTopologyHelper.java:133)
         at oracle.sysman.emai.model.mds.util.WLSTopologyHelper.getPartitionsList(WLSTopologyHelper.java:101)
         at oracle.sysman.emai.model.mds.RepositoryPartitionsModel.getPartitions(RepositoryPartitionsModel.java:231)
         at oracle.sysman.emai.model.mds.RepositoryPartitionsModel.initializeData(RepositoryPartitionsModel.java:207)
         at oracle.sysman.core.model.util.ModelUtil.initializeMBEMObjects(ModelUtil.java:245)
         at oracle.sysman.core.model.util.ModelUtil.initializeAllEMObjects(ModelUtil.java:120)
         at oracle.sysman.core.model.util.ModelUtil.initializeAllEMObjects(ModelUtil.java:93)
         at oracle.sysman.emSDK.adfext.ctlr.EMPagePhaseListener.detectContextChange(EMPagePhaseListener.java:579)
         at oracle.sysman.emSDK.adfext.ctlr.EMPagePhaseListener.doPostInvokeApplication(EMPagePhaseListener.java:544)
         at oracle.sysman.emSDK.adfext.ctlr.EMPagePhaseListener.afterPhase(EMPagePhaseListener.java:243)
         at oracle.adfinternal.controller.lifecycle.ADFLifecycleImpl$PagePhaseListenerWrapper.afterPhase(ADFLifecycleImpl.java:531)
         at oracle.adfinternal.controller.lifecycle.LifecycleImpl.internalDispatchAfterEvent(LifecycleImpl.java:120)
         at oracle.adfinternal.controller.lifecycle.LifecycleImpl.dispatchAfterPagePhaseEvent(LifecycleImpl.java:168)
         at oracle.adfinternal.controller.faces.lifecycle.ADFPhaseListener$PhaseInvokerImpl.dispatchAfterPagePhaseEvent(ADFPhaseListener.java:124)
         at oracle.adfinternal.controller.faces.lifecycle.ADFPhaseListener.afterPhase(ADFPhaseListener.java:70)
         at oracle.adfinternal.controller.faces.lifecycle.ADFLifecyclePhaseListener.afterPhase(ADFLifecyclePhaseListener.java:53)
         at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl._executePhase(LifecycleImpl.java:352)
         at oracle.adfinternal.view.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:165)
         at javax.faces.webapp.FacesServlet.service(FacesServlet.java:265)
         at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
         at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
         at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292)
         at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.adfinternal.view.faces.webapp.rich.RegistrationFilter.doFilter(RegistrationFilter.java:85)
         at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420)
         at oracle.adfinternal.view.faces.activedata.AdsFilter.doFilter(AdsFilter.java:54)
         at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl$FilterListChain.doFilter(TrinidadFilterImpl.java:420)
         at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl._doFilterImpl(TrinidadFilterImpl.java:247)
         at org.apache.myfaces.trinidadinternal.webapp.TrinidadFilterImpl.doFilter(TrinidadFilterImpl.java:157)
         at org.apache.myfaces.trinidad.webapp.TrinidadFilter.doFilter(TrinidadFilter.java:92)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.help.web.rich.OHWFilter.doFilter(Unknown Source)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.emSDK.license.LicenseFilter.doFilter(LicenseFilter.java:101)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:191)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.emas.fwk.MASConnectionFilter.doFilter(MASConnectionFilter.java:41)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.adf.library.webapp.LibraryFilter.doFilter(LibraryFilter.java:159)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.eml.app.AuditServletFilter.doFilter(AuditServletFilter.java:179)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.eml.app.EMRepLoginFilter.doFilter(EMRepLoginFilter.java:203)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.core.app.perf.PerfFilter.doFilter(PerfFilter.java:141)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.sysman.eml.app.ContextInitFilter.doFilter(ContextInitFilter.java:527)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at oracle.dms.wls.DMSServletFilter.doFilter(DMSServletFilter.java:202)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
         at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
         at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3588)
         at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
         at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
         at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2200)
         at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2106)
         at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1428)
         at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
         at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
    Caused by: java.sql.SQLSyntaxErrorException: ORA-00942: Table ou vue inexistante
         at oracle.jdbc.driver.SQLStateMapping.newSQLException(SQLStateMapping.java:91)
         at oracle.jdbc.driver.DatabaseError.newSQLException(DatabaseError.java:133)
         at oracle.jdbc.driver.DatabaseError.throwSqlException(DatabaseError.java:206)
         at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:455)
         at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:413)
         at oracle.jdbc.driver.T4C8Oall.receive(T4C8Oall.java:1034)
         at oracle.jdbc.driver.T4CPreparedStatement.doOall8(T4CPreparedStatement.java:194)
         at oracle.jdbc.driver.T4CPreparedStatement.executeForDescribe(T4CPreparedStatement.java:791)
         at oracle.jdbc.driver.T4CPreparedStatement.executeMaybeDescribe(T4CPreparedStatement.java:866)
         at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1187)
         at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:3386)
         at oracle.jdbc.driver.OraclePreparedStatement.executeQuery(OraclePreparedStatement.java:3430)
         at oracle.jdbc.driver.OraclePreparedStatementWrapper.executeQuery(OraclePreparedStatementWrapper.java:1491)
         at weblogic.jdbc.wrapper.PreparedStatement.executeQuery(PreparedStatement.java:128)
         at oracle.mds.internal.persistence.db.fcf.FailoverUtils.executeQuery(FailoverUtils.java:357)
         at oracle.mds.internal.persistence.db.fcf.FailoverUtils.executeQuery(FailoverUtils.java:123)
         ... 111 more
    Edited by: farouk on 26 oct. 2009 02:31

  • What is diff b/w pick and switch activity in bpel?

    what is the difference between pick activity and switch activity in BPEL? example Please

    1)The switch activity is an IfElse with two different flows, based on a conditional expression, derived out of existing message(s) in your process.
    Eg. i) Whether the salary is greater than 10,000 or not.
    ii) Whether the age is greater than 60 or not.
    iii) whether the department is finance or not.
    2)The pick activity is an IfElse with two different flows, based on two different messages/signals, that you can expect to receive(when you are waiting for a message) from outside of your process.
    Eg. i) whether you received a reply message or a timeout signal.
    ii) whether you received a AddNewEmployee message or UpdateEmployee message.
    The (decision for which route to be taken for) pick activity is based on the MessageType, while the switch is based on the contents in a message. The pick activity implies that you are waiting for a message, this can occur, at the start of your process or in the mid of your process. However, switch activity doesnot wait for any message, hence can only occur in the mid of the process and can not be the start of a process.
    Mark the posting appropriately as "helpful" or "correct answer", if your issue is solved.

  • Updated to Mavericks. Now theres tons of activity in my terminal and my activity monitor doesn't seem normal. I want to think someone's hacking me, but i need experienced help please!

    I spent all night trying to fix this. It seems to me that someone has been trying to hack into my system with all of the random codes/lines in my terminal and i have all of his foreign IP addresses. And now i get this strange message that popped up in my terminal. Idk what it entirely means? I would very appreciate if someone could just walk me through this. Thank you very much.
    First time poster. I have Macbook Pro. OSX. Just downloaded the new mavericks. I'm i have my firewall on. I stay secure. I run Netbarrier, Virusbarrier, IdentityScrubber.
    I know something is a little odd or just doesn't make since about my activity monitor. Then my WiFi was hacked last night and this person was writing tons lines of commands/codes that i found in my terminal and my activity monitor doesn't look normal,  and I've only been a mac owner for about a year now and i'm learning more and more but while trying to figure out what was going on this message popped up which concerned me the most. Any help would be most appreciated, thanks guys. I have my terminal full of his foreign ip addresses i noticed, and a lot of other commands and lines he wrote out that i definitely did not type myself. Can anyone give me a hand on this? Thanks
    --- 192.168.1.103 ping statistics ---
    10 packets transmitted, 0 packets received, 100.0% packet loss
    Extol:~ FBI$ who
    FBI      console  Nov  7 02:14
    FBI      ttys000  Nov  7 04:33
    Extol:~ FBI$ whois
    usage: whois [-aAbdgiIlmQrR6] [-c country-code | -h hostname] [-p port] name ...
    Extol:~ FBI$ whois 192.168.1.103
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    # Query terms are ambiguous.  The query is assumed to be:
    #     "n 192.168.1.103"
    # Use "?" to get help.
    # The following results may also be obtained via:
    # http://whois.arin.net/rest/nets;q=192.168.1.103?showDetails=true&showARIN=false& ext=netref2
    NetRange:       192.168.0.0 - 192.168.255.255
    CIDR:           192.168.0.0/16
    OriginAS:
    NetName:        PRIVATE-ADDRESS-CBLK-RFC1918-IANA-RESERVED
    NetHandle:      NET-192-168-0-0-1
    Parent:         NET-192-0-0-0-0
    NetType:        IANA Special Use
    Comment:        These addresses are in use by many millions of independently operated networks, which might be as small as a single computer connected to a home gateway, and are automatically configured in hundreds of millions of devices.  They are only intended for use within a private context  and traffic that needs to cross the Internet will need to use a different, unique address.
    Comment:
    Comment:        These addresses can be used by anyone without any need to coordinate with IANA or an Internet registry.  The traffic from these addresses does not come from ICANN or IANA.  We are not the source of activity you may see on logs or in e-mail records.  Please refer to http://www.iana.org/abuse/answers
    Comment:
    Comment:        These addresses were assigned by the IETF, the organization that develops Internet protocols, in the Best Current Practice document, RFC 1918 which can be found at:
    Comment:        http://datatracker.ietf.org/doc/rfc1918
    RegDate:        1994-03-15
    Updated:        2013-08-30
    Ref:            http://whois.arin.net/rest/net/NET-192-168-0-0-1
    OrgName:        Internet Assigned Numbers Authority
    RegDate:
    Updated:        2012-08-31
    Ref:            http://whois.arin.net/rest/org/IANA
    OrgTechHandle: IANA-IP-ARIN
    OrgTechName:   Internet Corporation for Assigned Names and Number
    OrgTechPhone: 
    OrgTechEmail:
    OrgTechRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    OrgAbuseHandle: IANA-IP-ARIN
    OrgAbuseName:   Internet Corporation for Assigned Names and Number
    OrgAbusePhone
    OrgAbuseEmail: 
    OrgAbuseRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    Extol:~ FBI$
    Extol:~ FBI$ hosts
    -bash: hosts: command not found
    Extol:~ FBI$ who
    FBI      console  Nov  7 02:14
    FBI      ttys000  Nov  7 04:33
    Extol:~ FBI$ whois
    usage: whois [-aAbdgiIlmQrR6] [-c country-code | -h hostname] [-p port] name ...
    Extol:~ FBI$ whois  192.168.0.0 - 192.168.255.255
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    # Query terms are ambiguous.  The query is assumed to be:
    #     "n 192.168.0.0"
    # Use "?" to get help.
    # The following results may also be obtained via:
    # http://whois.arin.net/rest/nets;q=192.168.0.0?showDetails=true&showARIN=false&ex t=netref2
    NetRange:       192.168.0.0 - 192.168.255.255
    CIDR:           192.168.0.0/16
    OriginAS:
    NetName:        PRIVATE-ADDRESS-CBLK-RFC1918-IANA-RESERVED
    NetHandle:      NET-192-168-0-0-1
    Parent:         NET-192-0-0-0-0
    NetType:        IANA Special Use
    Comment:        These addresses are in use by many millions of independently operated networks, which might be as small as a single computer connected to a home gateway, and are automatically configured in hundreds of millions of devices.  They are only intended for use within a private context  and traffic that needs to cross the Internet will need to use a different, unique address.
    Comment:
    Comment:        These addresses can be used by anyone without any need to coordinate with IANA or an Internet registry.  The traffic from these addresses does not come from ICANN or IANA.  We are not the source of activity you may see on logs or in e-mail records.  Please refer to http://www.iana.org/abuse/answers
    Comment:
    Comment:        These addresses were assigned by the IETF, the organization that develops Internet protocols, in the Best Current Practice document, RFC 1918 which can be found at:
    Comment:        http://datatracker.ietf.org/doc/rfc1918
    RegDate:        1994-03-15
    Updated:        2013-08-30
    Ref:            http://whois.arin.net/rest/net/NET-192-168-0-0-1
    OrgName:        Internet Assigned Numbers Authority
    OrgId:          IANA
    Updated:        2012-08-31
    Ref:            http://whois.arin.net/rest/org/IANA
    OrgTechHandle: IANA-IP-ARIN
    OrgTechName:   Internet Corporation for Assigned Names and Number
    OrgTechPhone: 
    OrgTechEmail
    OrgTechRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    OrgAbuseHandle: IANA-IP-ARIN
    OrgAbuseName:   Internet Corporation for Assigned Names and Number
    OrgAbusePhone: 
    OrgAbuseEmail:
    OrgAbuseRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    Whois Server Version 2.0
    Domain names in the .com and .net domains can now be registered
    with many different competing registrars. Go to http://www.internic.net
    for detailed information.
    No match for "-".
    >>> Last update of whois database: Thu, 07 Nov 2013 13:19:14 UTC <<<
    NOTICE: The expiration date displayed in this record is the date the
    registrar's sponsorship of the domain name registration in the registry is
    currently set to expire. This date does not necessarily reflect the expiration
    date of the domain name registrant's agreement with the sponsoring
    registrar.  Users may consult the sponsoring registrar's Whois database to
    view the registrar's reported date of expiration for this registration.
    TERMS OF USE: You are not authorized to access or query our Whois
    database through the use of electronic processes that are high-volume and
    automated except as reasonably necessary to register domain names or
    modify existing registrations; the Data in VeriSign Global Registry
    Services' ("VeriSign") Whois database is provided by VeriSign for
    information purposes only, and to assist persons in obtaining information
    about or related to a domain name registration record. VeriSign does not
    guarantee its accuracy. By submitting a Whois query, you agree to abide
    by the following terms of use: You agree that you may use this Data only
    for lawful purposes and that under no circumstances will you use this Data
    to: (1) allow, enable, or otherwise support the transmission of mass
    unsolicited, commercial advertising or solicitations via e-mail, telephone,
    or facsimile; or (2) enable high volume, automated, electronic processes
    that apply to VeriSign (or its computer systems). The compilation,
    repackaging, dissemination or other use of this Data is expressly
    prohibited without the prior written consent of VeriSign. You agree not to
    use electronic processes that are automated and high-volume to access or
    query the Whois database except as reasonably necessary to register
    domain names or modify existing registrations. VeriSign reserves the right
    to restrict your access to the Whois database in its sole discretion to ensure
    operational stability.  VeriSign may restrict or terminate your access to the
    Whois database for failure to abide by these terms of use. VeriSign
    reserves the right to modify these terms at any time.
    The Registry database contains ONLY .COM, .NET, .EDU domains and
    Registrars.
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    # Query terms are ambiguous.  The query is assumed to be:
    #     "n 192.168.255.255"
    # Use "?" to get help.
    # The following results may also be obtained via:
    # http://whois.arin.net/rest/nets;q=192.168.255.255?showDetails=true&showARIN=fals e&ext=netref2
    NetRange:       192.168.0.0 - 192.168.255.255
    CIDR:           192.168.0.0/16
    OriginAS:
    NetName:        PRIVATE-ADDRESS-CBLK-RFC1918-IANA-RESERVED
    NetHandle:      NET-192-168-0-0-1
    Parent:         NET-192-0-0-0-0
    NetType:        IANA Special Use
    Comment:        These addresses are in use by many millions of independently operated networks, which might be as small as a single computer connected to a home gateway, and are automatically configured in hundreds of millions of devices.  They are only intended for use within a private context  and traffic that needs to cross the Internet will need to use a different, unique address.
    Comment:
    Comment:        These addresses can be used by anyone without any need to coordinate with IANA or an Internet registry.  The traffic from these addresses does not come from ICANN or IANA.  We are not the source of activity you may see on logs or in e-mail records.  Please refer to http://www.iana.org/abuse/answers
    Comment:
    Comment:        These addresses were assigned by the IETF, the organization that develops Internet protocols, in the Best Current Practice document, RFC 1918 which can be found at:
    Comment:        http://datatracker.ietf.org/doc/rfc1918
    RegDate:        1994-03-15
    Updated:        2013-08-30
    Ref:            http://whois.arin.net/rest/net/NET-192-168-0-0-1
    OrgName:        Internet Assigned Numbers Authority
    OrgId:          IANA
    RegDate:
    Updated:        2012-08-31
    Ref:            http://whois.arin.net/rest/org/IANA
    OrgTechHandle: IANA-IP-ARIN
    OrgTechName:   Internet Corporation for Assigned Names and Number
    OrgTechPhone:
    OrgTechEmail
    OrgTechRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    OrgAbuseHandle: IANA-IP-ARIN
    OrgAbuseName:   Internet Corporation for Assigned Names and Number
    OrgAbusePhone: 
    OrgAbuseEmail: 
    OrgAbuseRef:    http://whois.arin.net/rest/poc/IANA-IP-ARIN
    # ARIN WHOIS data and services are subject to the Terms of Use
    # available at: https://www.arin.net/whois_tou.html
    <Personal Information Edited by Host>

    haha, so now i'm thinking. I'm learning the terminal as fast as i can but there are several lines of codes and commands in there that throws up red flags to me that i don't fully understand. It just looks fishy too me. It would be highly appreciated if someone could just check this out just to tell me that i don't need to worry about it. Or point me in the right direction. I just feel un easy about this. ha.

  • Diff: Version on workflow builder and Maintain Active Plan version on SWU3

    Group,
    Can any one help me to understand the Version on workflow builder and Maintain Active Plan version on SWU3
    Thanks in advance !
    Richard A

    Dear Richard Antony,
    The Versioning in the Workflow is very important its some what simmilar to the version on any SAP Objets like Tables, Program etc.
    Here Suppose any change comes in working workflow, then in stead of directly change them you can create a version of them and them modify it. So that you can reverst back to that version if required.
    Like wise there is lots of importance of versioning Workflow.
    The Active Plan version is also important to establish at SWU3. As all the Workflow is using Organization management which is very depended on the Active Plan version. so based on which Plan version you want to use you can Provide in SWU3 to tell Workflow system to use this.
    Hope this will give you a clear picture.
    Regards,
    Chandrashekhar.

  • BO XI 3.1 installation and Upgrade activity Steps

    Hi Experts,
    Right now we are using BO XI R2 Version, Planning to uninstall XI R2 and do a fresh installation of BO XI 3.1 with SP3.
    Do I need to install the Java latest version for XI 3.1? Right now we have the following setting,
             j2re1.4.2_04
             j2re1.4.2_16
             jre1.5.0_14
    Since the up gradation of Reports, user, groups, universe events etc are from XI R2 version to XI 3.1.So Is it enough to    
    install BO XI 3.1 with SP 3, or do I have to go for FixPack inorder to avoid problem after this upgrade activity.
    Could you please tell me about the BOXI R2 to XI 3.1 installation and Upgrade activity Steps.
    Regards,
    Sridharan

    Hi,
    you dont need a special JRE version on the Server. With the installation of BO a own JRE will be installed for BOE. Only for developing WebI reports the developer need a 1.6.x JRE later on.
    There is already FixPack 3.1 out but installing "only" SP3 should be sufficient.
    I would recommend you check the upgrade guide from Rel.2 to XI 3.1:
    https://websmp208.sap-ag.de/~sapidb/011000358700001646952008E/xi3-1_bip_upgrade_en.pdf
    You need a S-User to Login.
    Regards
    -Seb.

  • I own a iPhone and I have in ÇáÇí Cloud account, but has been disabled worked ريستور and what worked device device is linked to the account books first and I am I do not know the account and password and wrote activation iphone and I am ready to prove tha

    I own a iPhone and I have in ÇáÇí Cloud account, but has been disabled worked ريستور and what worked device device is linked to the account books first and I am I do not know the account and password and wrote activation iphone and I am ready to prove that this device is not stolen any way you want

    Apple does not participate in these forums.  We're only users like you.

  • IMovie '11, what steps am I missing, when I go to SHARE, IDVD is grey and not activated, only ITUNES and MEDIA BROWSER? I want to burn a DVD.

    iMovie '11, what steps am I missing, when I go to SHARE, IDVD is grey and not activated, only ITUNES and MEDIA BROWSER? I want to burn a DVD.

    Share your movie to the Media Browser. Then, in iDVD, drag your movie in from the Media Browser at the bottom right.
    THe Share to iDVD option is only activated if your source material is DV or AVCHD.

  • To Apple Inc. respectable brothers, dear, I've purchased a Yvonne immediately after S Black color I did not know that the owner of the device may do Service i Claude and I've work restor of Yvonne and when activation asked me to calculate i Claude and I d

    To Apple Inc. respectable brothers, dear, I've purchased a Yvonne immediately 4 S Black color I did not know that the owner of the device may do Service icloud and I've work restor of Yvonne and when activation asked me to calculate icloud and I do not know;  I do not know who is the owner of the device with science I bought the machine from Turkey Fargo to help me, I was involved with this device, and I'm from users of the iPhone please help me thank you with the knowledge that Amy device is 013186007698501
    If it is possible to activate the iPhone and that did not help me Fargo just inform me or give me the e-mail which has enabled Claude feature so that I could e-mail correspondence on Arslo Please e-mail me
    For I am God and you will lose device safely God

    Birden konuları gönderme Lütfen dur.
    Buraya git -> https://discussions.apple.com/message/24870284 # 24870284

  • Integration of sap R/3 (4.7) and Microsoft active directory (2003)

    Hi All,
    I would like to know integration of sap R/3 (4.7) and Microsoft active directory (2003) and also SAP EP and Microsoft active directory. I have been working as a ep consultant with a local bank. I am new for this integration work, So please kindly provide me the steps for integrating these both directories.
    Pls help me with this issue.
    Thanks in advance,
    Regards,
    Raghav.

    Hi,
    First You should read:
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/bc72b890-0201-0010-3a8d-e31e3e266893
    Regards,
    Jarek

  • SCCM report to show last logged on user and the Active Directory department attribute of that user.

    I need to create an SCCM report to show last logged on user on all machines and the Active Directory department attribute of that last logged on user.

    You problem is here.
    right
    join v_R_User USR on USR.ResourceID
    = CS.ResourceID
    USR.ResourceID != CS.ResourceID, you need to map the username to the user logon to the PC. By using the user’s department information you will
    end up with unreliable results.
    Anyways you need to make these changes to your query.
    left
    join v_R_User USR on USR.Unique_User_Name0
    = CS.UserName0
    http://www.enhansoft.com/

  • I'm trying to get rid of logmein. I threw away the entire application but I can't remove it form my overhead menu bar and the activity monitor tells me it's still running.

    I'm trying to get rid of logmein. I threw away the entire application but I can't remove it from my overhead menu bar and the activity monitor tells me it's still running. How do I get rid of it completely?

    Install it again and use the developers uninstall instructions
    How to uninstall/install software on your Mac

Maybe you are looking for

  • Can I transfer songs from my old itouch to a new one with out the use of the computer?

    I need to buy a new ipod becuase mine doesn't play music anymore so my question is: "Can I transfer my songs that I have purchased on to my new ipod without using the computer?"

  • No video on podcasts

    I have several video podcasts thAt play on my apple tv, but with no video. They are playing as audio only podcasts. The same videos play fine in iTunse on my iMac and on my iPad. Any idea why? bob ATV 2.0 the black hockey puck, running OS 5.1.1

  • Automatic Clearing of Down payment at the time of creating Invoice

    Dear All, I have created a Service Purchase order. This is assigned to a WBS element.Then i created a vendor downpayment request against this order using F-47 then posted same from F-48. Then i created service entry sheet and accepted it.Now when i a

  • How to upload selections in web report

    Hello Experts, Problem Faced: When my user is executing the query in the web. In the initial screen there is s varaible for CSO entry. He wants to upload the CSOs from the text file to speed up the process. (In BEX analyzer there is an option as uplo

  • Import PDF into a PDF?

    We have a unique requirement. Once the PDf is generated thru Web Dynpro, the users want to be able to import one or more PDF documents at the end of the generated PDf document. Then they want to save it as one big PDF document. Is this doable? Has an