Meaning of MetroCluster Status Error? (7-mode)

Can anyone provide insight on the following error message?  What type of MetroCluster error may have occured to generate this message?  Are there any commands I can run to find out more info? node-01: node-02: Metro Cluster Status Error Do you wish to proceed with system start? ([n],y) If I answer "y", the system appears to come up fine. But the fact it is asking me, I assuming there is some sort of MetroCluster error.  Trying to figure out some more specifics. Any insight appreciated.
Thanks,Joyce  

 Joyce - Given that I'm teaching MetroCluster for a client in India this week this post realy caught my attention ! Best guess is that there was an unkown failure of the cluster, and the systems weren't sure of the state before the failure.It was probably a check to prevent a bad resync if there was a split brain scenario. I'd want to check the logs on both sides of the cluster to see what happened before the break.I probably would have isolated the down system and done this before proceeding with bringing the failed node back online. Thank you for this timely question.I'll probably use it as a teaching example in the morning.
I hope this response has been helpful to you.
At your service,
Eugene E. Kashpureff, Sr.
Independent NetApp Consultant http://www.linkedin.com/in/eugenekashpureff
Senior NetApp Instructor, IT Learning Solutions http://sg.itls.asia/netapp
(P.S. I appreciate 'kudos' on any helpful posts.)

Similar Messages

  • Material statuses error message should go after entering Trackin No in PO

    Hi All,
    I have created one Material statuses with error message, I have created material with the use of that material statuses..
    Its working fine,At the creation of PR, PO I'm getting that Error message..
    My requirement is if I enter Requirement Tracking Number at item level of PR or PO means that Material statuses Error message should Go out and system has to allow to create PR or PO..
    Is it possible?? how to do it?? plz help me...
    Is it possible in standard SAp???
    thanks and regards
    rames reddy

    Hi,
    You can keep Requirement Tracking Number as Required Entry in field selection key (NBF or a copy of NBF as ZNBF) of PO document type in u201CReference data, itemu201D segment in following path:
    SPRO > Materials Management > Purchasing > Purchase Order > Define Screen Layout at Document Level
    And then assign field selection key to PO Document type and save.
    SPRO > Materials Management > Purchasing > Purchase Order > Define Document Types
    Now create PO with PO document type, system will ask you to enter Requirement Tracking Number in u201CItem Overviewu201D unless then you can save Purchase Order.
    The same you can do for PR document type by having a field selection key for PR document type.
    Regards,
    Biju K

  • Export iPhoto slideshow to a DVD, but get message "OS Status Error -9459".  What does this mean?

    I have created a slideshow (with music) in iPhoto, and each time that I try to export the slideshow, iPhoto stops the process and gives me the error message "OS Status Error -9459".  What does this mean?

    Go into the System/Energy Saver preference pane and turn OFF all options.  Also turn off the screensaver. Then try again.
    OT

  • Error "Copying statuses in modifuication mode not allowed, see F1 help"

    Hi,
    I am copying the status EXT_ALV_GRID_NEW of program to a Z status for the same program saplkaep
    I am facing the error Copying statuses in modifuication mode not allowed, see F1 help
    Could any one explain how to solve the problem.
    Please

    Hi,
    Try to switch of modification assistant using following path.
    Edit->modification operations->Switch off modification assistant.
    KR Jaideep,

  • I recorded a Concert video on my D3200 and now I can not play it back on any of my apple devices it states 'OSS status error - 101' what does it mean and how can I correct it and watch my videos on my Mac?  Julie from LEEDS

    How do I watch my imovies on my IMAC and apple TV that i have recorded from my NIKON D3200 .
    message displayed as 'OSS Status error - 101' .... HELP !

    Hi Julie,
    I'm not sure I can help with the "OSSstatus error - 101", but just checked the specs for your Nikon D3200 (nice camera). Certain frame rates with Full HD video can pose problems for iMovie.
    Among other settings, I noticed that the Nikon can record 1920 x 1080 50p (or 60p for NTSC countries). That's 50 progressive frames per second. iMovie has trouble with that Full HD frame rate, but can handle 1920 x 1080 50i - that's 50 interlaced fields per second, being 25 frames per second (interlaced video has 2 fields per frame).
    So, it's possible that you recorded at 50p, hence the problem you are seeing. The best solution for you is to record 1920 x 1080 25p (25 progressive frames per second). That will work fine in iMovie and give excellent results. iMovie works best with progressive video.
    It's not clear from your question whether you've already imported clips to iMovie, or whether you are just having problems when trying to play back or export the clips from iMovie. In offering advice here, I'm assuming that you are having trouble importing to iMovie.
    If in fact the problem is as I've outlined (format/frame rate issue), there is a "fix" that will enable you to import the footage to iMovie. But it is fairly complicated. Here's a link to an excellent article by Ian Odgers that will take you through the steps involved:
    http://ianperegian.com/My_FZ35_38_Webpage/Edit_1080_50p_and_burn_a_disk.html
    John

  • "Submission status" error while posting comments using evcom

    Hi friends,
    I am  getting "Submission status" error while posting comments using evcom. This error comes up even when we use "post comments" option in Action Pane.
    The error text goes like this :
    Error Message -
    This cell can not be updated.  Submission status must be modified to allow changes.
         010_000|2009.TOTAL|INTERCO|NOPC
    How can we get rid of this error?

    That's means the status for that specific category, time entity is approved and you can not do any changes including
    comments chnages.
    You have to change first the work status for that entity and after that you will be able to submit your comments.
    Regards
    Sorin radulescu

  • STPPOD Idoc creation status : Error in ALE Service

    Experts,
    I am trying to send GR from MM to SUS in MM-SUS Classic Scenario on ECC 6.0 Server. I have also configured Goods REceipt Notifications Functionality to sending GR from MM to SUS.
    When i am trying to send GR Idoc is generated (STDPOD) but i am getting the Error whose status - 29 in WE02 t-code :
    Status Message for Selected IDoc
    Status Text:   IDoc: 0000000000211243 Status: Error in ALE service
    T100 Text:     Entry in outbound table not found
    While i have properly configured Partner Profile for  Message Type STPPOD :
    Partner Role          Basic Type     Receiver Port           Application     Output Mode
    LS        DELVRY03       A000000018 (XI port)           GRN               Transfer Idoc Immediately
    When i try WE19 t-code for this idoc, i found  the error "Port '' does not exist in the table of port descriptions"
    while  i have already defined port (A000000018)in WE21 t-code  and this port also working fine for other messages.
    Please suggest.
    Thanks.
    Regards,
    Pawan Keshwani

    Nikhil,
    Issue is resolved it was the wiered error. As i removed LS from the field  Partner Role in STPPOD message at  partner profile(WE20) for SUS Client in ECC. Now the message STPPOD outbound message working fine.
    Thanks.
    Regards,
    Pawan Keshwani

  • Currency Translation- Package Status error

    I am encountering the following error after running  the currency translation package.
    The following is the error message in the package log
    RUN LOGIC : Run program error,Message Number : ''''
    Failed
    Application:Sales Package Status :ERROR
    Can some one please tell me what does this error mean and how it can be resolved

    HI,
    This error has been discussed in many threads here in this forum.
    Refer these and see if u can get a solution:
    Re: Currency conversion issue.
    Re: Currency Conversion Problem
    Regards
    Navin

  • Redwood CPS job goes to status ERROR but job works completes ok in SAP

    Hi
    When I schedule a particular ABAP job to run in SAP from Redwood CPS it always completes with the Error status in CPS, but the job runs okay and ends in the Finished status in SAP.
    I tried a different ABAP job and this ran okay, with the CPS status going to Completed.
    I had a look at the CPS log files for the Erroring job and there were no errors in the 'log' file but in the 'step1/spool1' file there is the line 'Processing completed with errors'. Is CPS doing a little more than SAP as regards checking job statuses and looking in the spool file for errors?
    Checked the operator messages and all it says is:
    Job 1501323 (submitted from ZGB_FI_KO8G_SETTLEMENT copy from 2009/08/24 15:34:54,250 Europe/London)) has aborted due to at least one error while running the jobs in step: Job 1501324 (submitted from ZGB_FI_KO8G_SETTLEMENT copy from 2009/08/24 15:34:54,250 Europe/London))
    - doesn't elaborate why the job has status Error.
    Is this saying the CPS part had an error or the ABAP part??
    Ross

    Hi Anton
    I checked the Return Code Mapping for this system and it is empty. No post running action or a trigger has been configured.
    The first time I was having the error was after setting up a 2 step job chain. When I got the error (and the second step didn't run) I then submitted this first simple step from the job definition SAP_AbapRun in case there was an issue with the way I'd configured the chain; it still errorred though. All I am specifying is the ABAP program name, SAP job name, variant and queue to run on, and it does run okay in SAP.
    When you say "The actual error should be available in the logfile of the SAP job itself" do you mean the joblog as viewing in SM37? There are no errors in there.
    I'll have a play with the Return Code Mapping part as if CPS does search the spool for errors (perhaps by default?) and sets the status to error in CPS, I don't want it to stop the chain - although I guess I can always set the post action of step 1 to 'on error' 'continue'...
    Cheers
    Ross

  • QM STATUS ERROR

    Dear sir,
                I was loaded data into quality server,it tells data was loaded successfully,but shows Q.M STATUS ERROR,i am trying to active it but it was n't works properly.
    pls help me out.
    thank you,
    chitrapu

    hi,
    check the settings in ODS like upate to qm mode qutomatically.
    if you check that then you will not get this error.even after checking if you are getting the same error then go to monitor and click on the data targets in the status tab. go to the request and check the qm status if it is still red then double click on it you will get gray,red and green click on green and proceed .
    rgds,
    Rakesh.

  • Getting OSS Status Error 28 when trying to setup backup drive to time capsule on wife's new macbook air, what is error 28?

    Time Capsule--OSS Status Error 28 when attempting to set backup drive to time capsule data drive

    It just means it is not available.. I think.. apple doesn't exactly give you a guide to errors.
    What OS is on the MBA.. Yosemite??
    That would be absolute bog standard problem.
    Same as here.. Time Capsule OSStatus error 28
    Even with older OS apple introduced some poor networking decisions at lion which have carried through.
    1. Try a simple reboot of the TC.. then try a reboot of the whole network.
    No luck.
    2. Reset the TC to factory and redo the setup from MBA.
    Use short names no spaces and pure alphanumeric names and passwords.. nothing more than 20 characters.
    Use WPA2 Personal security only and password that conforms to the above.
    No luck
    3. Make sure the wireless is set to IPV6=Link-local only in the MBA.
    Tell us if those all fail.

  • SWC Load Error - Design Mode Problem

    Hi,
    I'm loading custom .swcs into my Flash Builder (4.5 Burrito) project and I get these errors. These will only appear in design mode (not in source mode) and will not be labelled under the Problems tab, rather the Design Mode Problems tab:
    SWC Load Error
    SWC file failed to load. Any component dependent on this SWC file will not be displayed in the Design Mode.
    The SWC may have failed to load because of: 
    *  Incompatible definitions caused by usage of a different SDK version 
    *  Missing referred class definitions
    I don't think this problem is caused by an SDK incompatibility, as all these swcs have been created under flex 4 and I'm pretty sure under the 4.5 SDK.
    Loading the components contained in these swcs onto my canvas (at design time) will work fine. I'm able to build and run the application without any errors caught by flash builder.
    Any idea how to fix this problem, or what it means?

    SWC Load error indicates that the swc used does not match with the definitions present in design view or with what is present in already loaded other lirbaries.  The issue is reported by the flash loader.  It looks like that, your swc is compiled with a previous version of the sdk and the design view and the related definition correpsonds to another version.
    The incompatability logic is not in DV.  When DV tries to load all the swc details available in the project, the loading fails as the loader reports the issue. There is hardly anything, we can do here from DV.  If the player reports the incompatability issue, the loader is corrupted and all further loading is ignored. So to avoid such issue, DV ignores the failed swc's and tries to proceed.
    If you pass me the swc , I can give the details of the incompatability. Ideally between 4.5 and 4.5.1 there should not have been any incompatability.  However your case shows there is.  You can contact me at [email protected]

  • ERROR: Update mode C is not supported by the extraction API - R3 11

    Hi gurus,
    I just tryed to implement the solution I found at this link:
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/d3219af2-0c01-0010-71ac-dbb4356cf4bf
    The data source is based on an Infoset on the KONV R/3 Table.
    I setted the AIM delta process and I did all the activities as written in the document.
    The process works if I load data to bw in "full", with "Init without data transfer" and "delta" mode. Of course if I change a Purchase document, it will be posted in the delta queue and then loaded to bw with the next delta load.
    The "initialize delta process" (with data) doesen't work and returns the following error:
    Update mode C is not supported by the extraction API
    the error code is R3 11.
    have you any idea about it???
    Thanks!!!
    Regards!
    Matteo

    Hi,
    for me it sounds quite simple. It is that the update mode 'C' get flagged as 'not allowed' for this extractor. Did you check with rsa3? I guess you will get the same error message. May be you can start debugging in rsa3 to find the place where the update mode gets checked.
    Anyway, it shouldn't be a issue as you have a workaround. May be you should raise a error message at sap because of this.
    regards
    Siggi

  • Status error in workflow while changing personnel admin in pa30

    HI,
      I have created a leave request in PA30, so that a workflow has to trigger, for personnel admin i am using custom rule for agent selection. I am following error in inbox instead of work item.
    Workflow 1712 set to status ERROR
    Please repair the suspended workflow
    Context Information:
    ID: 1712
    Work Item Text: hd
    User: WF-BATCH
    Language: E
    SAP System: SCD
    Client: 200
    Press 'Execute' to display the workflow that has errors.

    hi,
    Thanks for the reply.
    I am getting error messages as follows;
    1. error when starting workitem 000000001791
    2. error when processing node 0000000018
    3. error when creating a component of type step
    4. error when creatind a work item
    5. agent determination for step 0000000018 failed
    6. Error in the evaluation of expression '&EMPLOYEET<???>.ADMINISTRATOR.ADMINISTRATORGROUP&' for item
    7. Error when determining attribute 'ADMINISTRATOR' of object instance '[BO.EMPLOYEET.]'
    8. Error in the evaluation of expression '&EMPLOYEET<???>.ADMINISTRATOR.ADMINISTRATOR&' for item '10
    9. Error when determining attribute 'ADMINISTRATOR' of object instance '[BO.EMPLOYEET.]'
    10. Work item 000000001791: Object FLOWITEM method EXECUTE cannot be executed
    The exceptions are,
    process_node, create, create_wim_handle, create_via_wfm, execute, cl_swf_bnd_binding->execute, get_value_ref, eval_bor_atrrib_access-code.
    I have used the method approveinteractive in task in custom workflow and also custom rule for agent selection. I did binding between the mentioned employeet.admingrp ,,, to the variables declared in rule container.

  • Time machine backup error OS Status error 2

    Time machine has been backing up to newly replaced Time Capsule with no Time Machine issues until today.
    There have been a few Time Capsule 'amber flashing light' moments, solved with a reset.
    But after one such reset this morning, despite the green light being steady, the error message stated in the title above has appeared.
    Time capsule is visiblle and properly configured, according to Airport Utility.
    On the menu bar, the Tme Machine logo is grey, and states "Time Machine is not configured".
    In the Time Machine preferences window, have re set the Time Capsule as the backup disk (several times).
    Time Capsule green light is on, and I can hear it whirring into action when I select it as back up disc.
    The complete message reads:
    Time Machine can’t access the backup disk “(my name) Time Capsule”. Time Machine backup OS status error 2.
    I am Running OSX 10.6.7
    Time Capsule 1 TB
    Less than one month old, and the second time calsule replacement form Apple.
    Can anyone please shed any light on this?
    Many thanks
    Lorraine

    Is the NAS designed to work with Time Machine, because Time Machine isn't designed to work with a NAS.
    See this post (Major Dude) that is in the More Like This section:
    Time Machine and ReadyNAS Duo

Maybe you are looking for