MediaShield RAID 5 implementation on a P6N SLI Platinum plus boot question

Hi guys
I have a P6N SLI Platinum I am considering using to replace my old decrepit Thecus N4100+ NAS enclosure. My NAS has four 750Gb SATA II drives in RAID 5 giving a total usable amount of about 2Tb.
I have a few questions please:
What is the maximum size RAID that MediaShield will support? I seem to recall reading somewhere it was 1.6Tb? This is a problem with 3Tb storage (1/4 redundancy)!!
What is the performance like running RAID 5? What are the read/write times like?
How much of a performance hit does the PC take running RAID 5 with MediaShield? This box has an E5500 quad core 4*2.8Ghz chip but is running some very hungry software (one build is a DAW based on Cubase and various VSTs; another is running Photoshop CS3) which I can't afford to be tied up sorting out low level RAID stuff if it's going to be a problem. Can I dedicate one of my four cores to the XOR for the RAID 5 freeing up the other three for actual PC stuff?
There is currently one SATA drive already in this box containing the OS. If I use the four SATA ports for the MediaShield RAID and buy a 3rd party PCI/PCIE SATA controller card to plug this current drive into will I be able to set it to boot from it or do I need to migrate the drive to an IDE drive and put it on the IDE chain?
Many thanks in advance you guys.
Cheers

Where do I start?
I have a E5500, it's a dual core chip.
Second, media shield sucks. Don't use it unless absolutely necessary.
Buy a pci-e 1x 'firmware' card, I use the RocketRaid 2300 cards, good and cheap. Good, usable RAID5.
They have a performance advantage, a load time advantage, cpu utilization advantage, and most importantly, if you want to migrate your array over to another motherboard, you can. Easily.
If your mobo dies, and you replace it with a more current one, your array is toast with mediashield.\
Boot from a motherboard sata port. Don't boot from a RAID 5 array, trust me.
http://www.newegg.com/Product/Product.aspx?Item=N82E16816115029

Similar Messages

P6N SLI Platinum not booting after CPU change

I just upgraded the CPU in my machine with a P6N SLI Platinum motherboard from a E6700 to an E8500. I first upgraded the BIOS to 1.7 as the MSI page seemed to indicate that was a pre-req for this CPU. The machine was working fine for a day with the new CPU.
I changed the CPU in the machine and when I tried to boot, the lights on the motherboard came on as well as the fan, but no video or sound. In addition none of the diagnostic LEDs on the D Bracket light up. They had been previously working. Neither do the lights on my memory sticks light up.
I tried clearing the CMOS by hitting the switch but nothing. I am now going to try switching back CPUs but I don't have much hope that that is the problem given the diagnostic LEDs don't light. Does anyone have any suggestions as to a fix or is this motherboard fried?
P.S. Do you hit hte CMOS clear switch when the computer is off but the motherboard is charged? Or do you unplug the computer and wait for the internal orange light to go out as well too?

Quote from: Henry on 24-January-10, 11:41:19
What is the QC number (by the cpu socket) is 01, 02, or 03?
See this thread for more:
https://forum-en.msi.com/index.php/topic,123486.msg932471.html#msg932471
Ah. Given I bought my P6N SLI Platinum 3.5 years ago when they first came out I imagine mine is one of the older versions that doesn't support 45nm CPUs by default. Is there a photo somewhere showing where the QC number is located exactly on this MB? It's probably located under my huge CPU heatsink and I'm not going to remove that for a third time just to check.
I really wish the MSI CPU compatibility page mentioned that. It would save me a lot of time. It's not worth my time and effort to dismantle my PC, send them the MB and wait for them to send me back a compatible one.
I verified the BIOS upgrade by looking at the version number at startup and using CPUZ.

P6n sli platinum cannot boot up

Hello
Everytime I boot up the D bracket suggests the computer is failing on initializing the floppy drive controller. i have changed the cable, and changed the floppy drive but same effect.
In the BIOS, if I go through and F10 for no save and exit, it then exits to bank screen as it fails at the point above. If i make any changes in the BIOS, and then try to accept those changes it freezes on pressing either Y or enter. At that point all I can do is turn off and start again. Naturally it doen't retain those changes. I have done this several times to disable the floppy.
I have removed the battery and put it back, (It's 16 months old). It then did allow me to disable floppy but still machine did not go beyond the above point. Whenever I have tried to go back into the Bios again, it will now freeze when I try and accept any change in settings.
As you will see I am unable to even boot from a floppy at this point so cannot een consider updating the BIOS. However before yesterday it has been working perfectly.
Any suggestions, or the loan of an axe to reprogramme the ****** thing would be much appriecated.
Thank you
Malcolm
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago

Quote from: yokochanie on 03-October-08, 13:55:28
Motherboard P6N SLI Platinum, G52-73501x1-Q05
2.20.0050.10 BIOS verison
Intel Core 2 Duo Processor
Sony MPF920 floppy
4 Harddrives. Boot is IDE, then 3 others, one of which is sata
2 memory sticks, 2 gb ram
Plexwriter CD
Pioneer DVDRW 105
Pioneer DVD
DMX-6fire soundcard
HD620W power supply
full details not known as mostly stored on the computer
No faults on system since it was built 16 months ago
"2 memory sticks, 2 gb ram"
That doesn't talk much, we need full details about it.
"Intel Core 2 Duo Processor"
Which one?
"2.20.0050.10 BIOS verison"
That's not your BIOS version, look here how to check==> https://forum-en.msi.com/index.php?topic=113146.0
What VGA you use?
Remove power cord from the PSU and leave just one memory stick in 1st DIMM, once done proceed with >>Clear CMOS Guide<<
Then try to boot, if no change disconnect any storages{4 HDD's, 3 Optical drives, and any USB devices which you may have attached} and re-test.

MSI P6N SLI Platinum OEM Modification Question

The MSI P6N SLI Platinum OEM edition motherboard comes with all the circuit layout needed to support 2 SLI x16 Style connectors for SLI'd video cards. However the OEM only comes with one installed and an empty slot for the other. What resistors and the like would I need to add to the board in order to add the pcie x16 connector to the empty area on the board? I've already found a source for the actual slot, and I know I am going to need to add a resistor of some type to the empty resistor slot directly above where the PCIe slot will go. Beyond that I don't know what else I need to do, or what type of resistor is needed.
Oh yeah, and where can I go to buy the optional accessories for this board that came with the retail version? I would have prefered the retail version but the board I have came as part of a kit.

Hello Tornath,
you have already mentioned yourself, that you have an OEM-Board, not an MSI-Retail Board. MSI does not provide end-user support for OEM products, as this is the responsability of the OEM Vendor who is selling OEM Boards under a different name. Also, this forum will not support OEM Products and that is why I will have to close this thread.
However, before you waste huge amounts of your lifetime with trying to add a second PCI-Express Slot to your OEM-Board, let me explain to you, why your plan is rather pointless:
1) The only OEM-Board of this class I know of, has the model number MS-7350VP. If there ever was a marketing name, it would be called P6N Platinum (not P6N SLI Platinum), and there is one simple reason for that:
2) This particular OEM Board has an NVIDIA nForce 650i Ultra Chipset (as opposed to the NVIDIA nForce 650i SLI), and if you look at the specifications for NVIDIA Chipset on the official NVIDIA Chipset Specification Site, you will see that this Chipset does not support the NVIDIA SLI™ Technology: http://www.nvidia.com/page/nforce_600i_tech_specs.html .... That is basically why there is no additional PCI-Express Slot in the first place. So even if you should succeed in adding a secondary PCI-Express Slot to the board physically, the chipset will render it more a less useless in terms of running two video cards in SLI mode.
**TOPIC LOCKED**

P6N SLI Platinum - E4300 multiplier drops to 6x

Hi all, first post. Did some searches on here and can't find an answer, also this is a pretty new mobo.
CPU-Z shows my cpu at 1.8ghz @ 9x multiplier, but every few seconds it switches to 1.2ghz @ 6x multiplier. This sounds like a speedstep issue, but I disabled EIST in the BIOS, and all spread spectrum options. In windows power management I set it to Always On. I see a lot of talk about C1E but don't see any option regarding that setting in my BIOS.
Is this normal behavior for the E4300? I'm hesitant to start OC'ing when I'm having issues at stock clock.
Thanks for any ideas.
My setup:
P6N SLI Platinum / E4300 / Scythe Ninja / Antec Trio 650 / 2x1 GB Corsair XMS2 6400 / 2x WD 160gb - RAID 0 / Leadtek 8800gts 640

Quote from: Maesus on 06-March-07, 09:06:11
how about locking it to 6x and ramp up the FSB much higher?
Would there be an advantage to that versus a 333fsb x9 (3ghz) OC? I didn't get the best ram in the world because I wasn't looking for crazy speeds. The PC-6400 Corsair ($160 w/rebate) I have is rated at 5-5-5-18 at 1.8v. I have it at 5-5-5-12-2T at 1.9v. I'm not uber-conversant on memory timings but when I set it on 1T windows crashed immediately. Anandtech mentioned that changing to 1T had little to no real world performance improvements so I can live with it.
Currently I have the fsb at 333 (1333 in BIOS setting) and DRAM at 333 (666 in BIOS) so I have a 1:1 ratio which I understand is preferable. The MSI Dual Core utility reports that my CPU is running about 7 degrees cooler than the System temperature. Is that possible, or do I have a jumper setting mixed up somewhere...

Net Issues with P6N SLI Platinum

Hello all. I am having issues getting the internet to work on my new system with the following specs:
Mother Board = MSI NVidia nForce 650i SLI Chipset Based P6N SLI Platinum
CPU ............ = Intel Core 2 Quad Q6600, LGA775 Pkg 2.40 GHz, 8MB L2 Cache Total, 1066 MHz FSB
Memory ...... = Geil 2GB PC2-6400 DDR2 800 CL=5-4-4-12 1.9-2.5v (x4)
PSU ............ = Zerodba 620W
Video .......... = EVGA e-GeForce 8800 GTS
Hard Drives . = Seagate Barracuda 320 GB SATA 3/GB Transfer
OS .............. = Vista Ultimate OEM 64-Bit
I can't get the system to recognize the router or network or even access the internet when plugged directly into the cable modem. I've power cycled plenty of times, and the other systems in my network work without fail. I've disabled UAC, windows firewall, and anything else that might be interfering on the software end. I have installed the latest drivers from the msi site, and have even installed the latest nforce drivers from NVidia's site as well. Any suggestions would be appreciated!

Quote from: Maesus on 29-September-07, 09:00:00
1. make sure you enable LAN in the BIOS
2. make sure the LAN driver is properly installed in the BIOS
3. make sure your cable modem can detect your LAN - did you implement MAC address filtering? set the LAN speed to be detectable by the cable modem, ie 10Mbps?
1. The onboard LAN controller is enabled in BIOS
2. Not sure how to go about doing this exactly.
3. MAC address filtering is only enabled for wireless connections and it seems that the router is "seeing" the system. I have connected directly to the modem as well to no avail. I'm not sure how to set the LAN speed to be detectable to the cable modem.
"Check your network speed and try not to use Auto negotiation. Try setting it to 100Mbps full duplex, or 10Mbps full and see how it goes."
Where would I be able to adjust these settings exactly? Thanks for the help so far!

P6N SLI Platinum - ERROR - not enough space to copy PCI option rom

Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?

Quote from: kakalake7 on 24-March-07, 04:34:46
Can Someone Help Me with this Problem?
I have P6N SLI Platinum motherboard, after I plug in two INLINE Silicon Image 4xSata PCI Raid adapter (Sil-3114) bios is displaying Error message - ERROR - not enough space to copy PCI option rom
I have the lastest BIOS..
Is there eny cure for this Problem?
How's everything at your side now?

MSI P6N SLI Platinum + E6850 + 533Mhz (PC-4200) RAM?

Hi,
I got hold of an E6850 (1333 MHz FSB) CPU for upgrade and I would like to know if it can run with 2Gb hynix RAM (533MHz PC-4200) on my MSI P6N SLI platinum (Rev 1.0). If it will run, how much performance loss would there be compared to using 667MHz or 800MHz RAM?
Thanks.

I am not sure if the Nforce Chipset/Memory Controller is able to support a memory bus speed that is lower than FSB Clock Speed. Intel Chipset usually can't do that (1:1 usually being the minimum ratio supported). However, on your board, the memory speed is not directly tied to the FSB Clock Speed and can be adjusted independently, so the situation may be different. The bottom line is: I can't tell you for sure if it will work or not and therefore suggest to simply test it and see what happens.
Quote
If it will run, how much performance loss would there be compared to buying PC-6400 800MHz RAM?
With the memory bus running slower than the Front Side Bus, there will be definately be a performance difference that is not insignificant.

P6N SLI-FI & P6N SLI Platinum

Main purpose for those betas, fix for slowdown issue when using 4GB system memory.
beta BIOS for P6N SLI Platinum ver V1.32:
BIOS Sign-on message: MSI P6N SLI Platinum A7350NMS V1.32 050307 (Date: 05/03/2007)
Attachment name: P6N SLI Platinum BIOS 1.32.zip
beta BIOS for P6N SLI-FI ver V2.22:
BIOS Sign-on message: MSI P6N SLI A7350NMS V2.22 050307 (Date: 05/03/2007)
Attachment name: P6N SLI-FI BIOS 2.22.zip
Make and ensure PC is stable before proceed. flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!

Quote from: BOSSKILLER on 29-April-07, 00:17:22
Main purpose for those betas, fix for slowdown issue when using 4GB system memory.
beta BIOS for P6N SLI Platinum ver V1.32:
BIOS Sign-on message: MSI P6N SLI Platinum A7350NMS V1.32 050307 (Date: 05/03/2007)
Attachment name: P6N SLI Platinum BIOS 1.32.zip
beta BIOS for P6N SLI-FI ver V2.22:
BIOS Sign-on message: MSI P6N SLI A7350NMS V2.22 050307 (Date: 05/03/2007)
Attachment name: P6N SLI-FI BIOS 2.22.zip
Make and ensure PC is stable before proceed. flash BIOS from USB key, by using our Tool(easy & safe way to flash):
MSI Forum HQ USB Flashing Tool
Use Beta or Modded BIOSes at own risk!
i have the problem with the 4gb upgrade (slow) on winx64. my question is do i have to use this bios ver 1.32 or get the latest and the greatest bios v1.6 for my mobo p6n sli plat?
thanks in advance.
-alex

P6N SLI Platinum random shutdowns

System:
MSI P6N SLI Platinum MoBo
Intel E6750 CPU
Etasis 850W PSU
Corsair CM2X1024-6400C4 RAM (using only 1 stick while troubleshooting)
MSI NX8600GTS GPU
OK, this is a strange one. I put my new system together and everything seemed to be working fine. POST looked OK, and I was even able to install Windows. Everything seemed stable.
One thing that troubled me was that the lights on the D-Bracket were all red AFTER POST. In other words everything was working, but the LEDs were showing CPU problem. I tried everything I could think of to get the lights to go away, but nothing worked. I disconnected all HDs, DVD, and floppy drives. I reset the BIOS, and reseated the CPU. I tried putting RAM in different slots, tried both sticks solo, but nothing made any difference.
It was getting late, so I decided to go to bed and run memtest86+ over night. When I got up this morning the system had powered itself down. When I turned it on again it powered itself off within a minute of being turned on. This was with all the drives hooked up, so I disconnected everything and now it's been sitting happily in the BIOS for over 30 minutes.
So at this point, it seems like it could be a power supply issue. Unfortunately, I don't have another PSU with an 8-pin CPU connector that I can try in this system. Any thoughts? Next steps to try?
Other possibly useful facts:
When I boot into the BIOS the D-Bracket lights show #3 green, and all others red, indicating "initializing keyboard controller". But when I boot past the BIOS to a CDROM or Windows, they show all red, indicating "CPU problem"
The system makes a brief chirp the POST screen. It doesn't sound like a beep code to me, and I've heard some boards will do an "everything's OK" beep like this. But it could be important so there it is.
Although it seems happier with all the drives disconnected (indicating a PSU problem), it still shows all red LEDs on the D-Bracket (indicating a CPU problem).
This is not the first system I've built, and I was fairly careful about putting everything together the right way. The only goof I know of is that at one point I was unplugging and re-plugging things and I ran the system for a while without connecting PCIE power to the GPU. Could that have broken something?
Any help would be much appreciated.
-Steve

UPDATE: I tried hooking up my old 400W PSU with 20-pin ATX and 4-pin CPU connectors (apparently this is OK to do) but there was no change. Still four red LEDs.
I also tried removing the PCI-E GPU and booted it up with an antique PCI VGA card. Again, no change. Maybe I really did get a bad CPU?
Any other ideas, before I try to return my CPU?

[P6N SLI Platinum] black screen NO BOOT after D-bracket replug [RMA-SOLVED]

Quick setup specs;
P6N SLI Platinum
E6600 (box/stock 2400mhz basic)
2x 1Gb DDR2 6400 Gskill HZ
Sapphire ATI X1600Pro (PCI-e basic)
Aerocool Zero DBA 620W
(2 HDs sata, 2 Hds pata, 2 optical pata at first -all OK at first, disconnected after, so irrelevant here ,( )
(XP Pro clean new install from start)
I tried to check the forum old posts before trying to write that new one, but could not find any really related totally adequate posts so far (or i missed them, sorry if so, then -?). I could already find very useful informations on first aid usual 'rebooting' procedures to follow with minimum new boot configurations, d-bracket new LED signals etc. But so far no luck, all same, nothing better, nothing cured here for the stuation here. ,(( Also excuse my english if not perfect, i am not english either. ,(
VERY bad & sad problem here... ,(((( :
All was working perfectly great during 5 days.. the P6N SLI platinum install went GREAT initially (as normal, not a first pc built, all normally happening, so far so good, etc).... all hardwares compatible together at first (dedicated ATX 'full' 8x8 pins connector too for the cpu only for ex -all working perfect at first try. quick tensions 5V/12V under msi dual core control tool perfect too etc), was great easy going/ great strong ultra-stability feeling on the hardware side.. i was just now concentrating on the software side (no special BIOS tweaks even attempted so far, all on basics-normal e6600/ddr2 auto-settings, apart at the end ddr2 quick test -when problem occured- on 450(900?)Mhz at 2.1V, far far easy under its possible specs max anyway.. and had been working perfect for 3 days with that little ddr2 boost try -no time for special bios further tweakings now, etc), reinstalling and transfering/reorganizing slowly my necessary files/hds/softwares from old to new setup, no oc, nothing special tempted (i was planning oc, new cpu more suited fan/silver6 etc only for the end..), LAN file sharing setup done, Realtek audio setup test done, etc ; installation had been so far one of the quickest and problem free ever... explaining maybe also my fatal lack of cautioun for just (too much) 3 sec in the end after 5/- days of perfect working new ring going on.. ,((( :
At first, i also tried to immediately install the D-Bracket too to check possible hardware install problems -very useful feature i of course thought too..and wanted to try too, "in case of"..- (installing it from quick reading of the printed manual..with no colour pic coding inside..and quick error coming from there thereafter with an initial mismatch usb/jbd1 inverted plugs connections.. *both* having the exact same pins numbers and dispositions, beeing side by side on mainboard layout.. and so able to connect both headers indifferently.. so i did not see it immediately (( .. and no way to see it otherwise as such, anyway.. ,( ), just to be sure all was ok. I noticed that LED were of course, never lightning (not normal).. but as EVERYTHING else was working fine (GLAN, sound, etc etc).. i did not bother more than that -- error checking not necessary.
Till that fatal clumsy day i wanted suddenly to.. check the D-bracket too. ((((
All was working well, XP pro opened for hours as usual etc..
i had not yet totally finished to install the motherboard in the pc-case (always on desk, free in sight..)... so i could always see the connections on it. ... and i noticed that ... the colour headers codes were NOT matching (usb=yellow..).. i had just stupidly initially badly connected the D-Bracket jdb1/usb adjacent plugs (inverting them), so... And still, all had ever worked perfect.. except the D-Bracket, of course, was sending back no lights then, obviously.. so i did the fatal error.. confident all was stable enough and strong if even that initial plug error had had no consequences at all.. i did the fatal bad move to try to UNPLUG the D-Bracket connectors and put them back in right orders WITHOUT switching OFF the power supply so... like an hot USB plug, sort of, in a way. fatal error.. :( :( :(
As soon as i began to remove the usb/jdb1 connectors and put them back in normal order... the system suddenly SHUT DOWN ... no special bad noise, no special smell.. just sudden SHUT DOWN.
From there.. impossible ever to boot back again the so far perfectly working machine (((((((((((( , always same till now :
i switch on the power supply.. orange led appears on motherboard (ok)... i switch on the motherboard.. green led on motherboard appears (ok)... CPU fan begins (ok), video fan begins (ok) .... and... NOTHING.. total black video screen. no more even possibility to see the BIOS. :( total dead startup .. and the fans are going on eternally, blocked eternally in that inital startup with leds on too (no sudden shut down after a few seconds.. just.. nothing)... :(
Suprem irony.. the D-bracket LED seems to 'work' now.. "of course". Just the PC no more booting at all ^. Only thing is that only green LEDs are appearing, no red ones... simply the sequence, from start and never changing :
1. GREEN 2. GREEN
3. GREEN 4. (---) (not red, just nothing -?)
If i look in manual, it means "Testing RTC (real time clock)". I don't know exactly what it means *here*, but sounds to me it is the most basic initial first BIOS checking.. and BIOS can't be reached for even that so ; BIOS fried???? :( :(
I tried every 'standard' things recommanded usually here in older posts, for new boots recovery attempts thereafter in such 'boot errors' situations (clear cmos button pushed in every possible ways -quick, long, quick etc..-, removing little by little everything but the very minimal least energy taxing setup; keyboard, cpu, video, motherboard; 1 ddr2 nearest cpu slot.. point).. NOTHING. Worst, i tried to boot with one of those elements missing.. exact same D-Bracket lightning from start to.. eternally (123 GREEN 4-nothing). Even tried to remove the little (cmos?) KTS lithium battery for a few hours -that could work sometimes with the old already ultra-sensitive amd/nforce2 chipset bioses problems, so i tried there too-?-; same 3 green lights and fans running and nothing else happening from there.. ((
Always the same; total dead boot as above. black screen. no possible access to even bios panel. ,(((
So my desperate questions, now: of course, the origin is obvious here; all happened "by my fault" when i tried 'too quickly' to 'hot-plugging' replace correctly the D-BRACKET plugs *without* switching off the power supply... all shut down suddenly when i put back correctly the usb& jdb1 headers... :( ;
- do you think there could be any possible last HOPES to recover the situation that i had missed (a well known situation in such d-bracket handling 'common' (?) connection error, a simple trick to try i had missed ??)
- do you think i FRIED something in the process on the motherboard ?? :( :(
- do you think it is 'only' the BIOS (fried????) ?? :( :(
- do you think i could have fried a specifical external key component in the process (not necessarily motherboard) : ddr2 modules, cpu, video card????? :( :(
- is my only solution is to send the motherboard to RMA (no other ways now) ???
please, don't hesitate to give me any possible hints to try to avoid the RMA process.
can i avoid it, right now?
is that possible to fry an whole board just with such a D-Bracket 'hot plug switch' (on a so far perfectly working -light- setup - no oc, little video card, etc) ???? :( :(
That is the only C2D Intel/ddr2 motherboard i have here around. No possibility to test elements by elements for precise error checking (cpu, ddr2 modules, video card or powersupply).
Only things i could check so far are;
- the power supply (aerocool 620W zeroDBA) ;
i tested it back on my old amd xp-m nforce2 setup.. always working apparently. NOT 'fried' so, apparently. but no way of course to test for exemple the special 8x8 (or 8x4) Intel ATX cpu connector on old xp-m motherboard. But power supply NOt fried at least, apparently -?
- the video card.
no way for me to really test the pci-e card on other motherboard around but.. i tried a very old PCI VGA card.. that one works on old setup.. and on P6N, no effect, doesn't improve the situation. So, not sure the new pci-e video card isn't fried.. but a new video card doesn't correct the dead boot problem.. (
No way for me to test the ddr2 or CPU directly though.
Do you think DDR2 or CPU could have been fried in the process too ???
or just, as i fear anyway, 'simply', the motherboard BIOS fried -??? :-(
Really, thx for any suggestions..
if there could be an 'hidden' trick i did not try yet to try to recover the (initially working perfectly!!! (( ) setup, WITHOUT engaging the motherboard RMA process (at least 2 or 3 weeks lost here to wait the return..online store etc..)....
please, suggest me.. ,((
i am *really* very sad of that stupid clumsy idea to want to 'enable' the D-Bracket.. all was working great so far.. and i lost all with just that stupid idea to try an hot plug bracket reconnection without switching off the power supply it seems.. can it be possible,sigh?? all seemed so stable before that, that i.. just lost my usual cautious just 3 sec too long it seems... :-(
Thanks in advance
hoping post not too long too, but i tried to expose the situation as precisely as possible; first time i ever had such a problem with a motherboard/system install.. that is quiet ironical knowing it was also the best and quickest/easiest easy going new built i ever had so far too.. till then ,( .. and all came from the 'helper' d-bracket 'luxury second hand possible boot helper diagnostic tool' checking in the end too, here.. really hoping i can avoid an RMA process.. and no other hardware elements (apart the motherboard?) could have been damaged in the process ? ,(((

hi, thx a lot for the quick answer. sorry for the length indeed (i did not know exactly how to describe the situation.. without omitting any later possibly important details).
Alas, i already tried that many times in following interesting asnwers on similar problems in old posts here; did NOTHING. ,(
But after your post, i tried it again, and removed for the remaining *hours* (6/8h?) the cmos battery as suggested again *too* so -pushed again the clear cmos button etc when battery out, then when in again, then replugging the powersupply etc; NOTHING better alas too. always same, no boot, black screen, no bios. ,(
Problem always the same, to sum up, for clarity:
power supply on => orange motherboard led is lightning up, motherboard on => green motherboard led is lightning up, cpu/video/case fans are working up as normal and.. that's all. nothing else forever. black screen. no signal. not a single chance to get again the bios setup screen.
another detail i omitted, maybe; keyboard lights are all lightnng up too.. and stay blocked in that state too. tested with 2 different keyboards, same. to shut down the leds, fans etc, only one solution, shut down the power supply button directly, at that stage.
right now, i test on barebone minimal system as recommanded too;
cpu, 1 dimm (closest cpu slot), video, keyboard. all rest disconnected.
i of course tried to reset the cmos with the 'magical red button' many times before, with power supply cable plugged out, pushed the button trying almost every possible way so far (quick, long, long sequences, short sequences etc etc)... changed NOTHING so far -is that thing working?? ,(. and right now, same after hours with cmos battery removed too. ,(
the d-bracket leds are always (now it is correctly plugged..) :
123 GREEN 4 (nothing)
"Testing RTC (real time clock)"
another 'interesting' detail is that; those leds are appearing IMMEDIATELY after the motherboard is switched on, from start (green led appearing on P6N). and it is staying as such till the end. nothing else. i tried to connect also the case speaker ; no bips, no sound signals at all too.
I also remind the system was WORKING like a dream during 5 days *before* i had that sudden TOTAL boot problem.... AND i touched almost nothing in the bios too all along, for initial security reasons too.. (i was concentrating on the software installs anyway right now, NOT on the oc side..). The ddr2 quick little change i did was also the ONLY change i tempted to simply test quickly some setting i already saw working without problem with that P6N and that kind of ram.. and it was working without problem so far too, so.. all the time idem. And it had been perfectly working for 3 days as such untouched from there; no problems at all (those memory modules have been seen on that motherboard largely at those specs, why i did that quick test anyway.. far under their possible max -micron chips). it was even working so well i forgot to put the setting back as default after that quick ram test.. so much it was stable too (even if i had not time to do real memtest test on that one - i did for many hours with the initial automatical default settings too, to check the ram quality, was perfect for many hours, so ok too, no bad ram initially too-; was so stable for all my XP software installs operations etc.. that i forgot it thereafter, to be true..why it stayed like that till that moment (incidently).. but i preferred to mention it 'just in case' though, yes. i also did not push at all the dimm voltages in the process, it was always far inside the specs at 2.05V to be exact -usual for that ram too up to those numbers easy for it. i did not push the ram voltages either so..).
The problem ONLY appears when i wanted to unplug the *initially* badly connected D-bracket headers so (inverted headers.. but that caused NO problems either so far too for the system stability.. only the LEDs were of course not working so far..) : i did the error to NOT switch off the power supply. :(
*then* immediately the system shut down... and above situation appeared. ,(
BUT all was working perfect before.. ram setting included so. ,((
So my simple questions now too ;
- do you know what means *exactly* the d-bracket message 'Testing RTC" (123 GREEN, 4 nothing).. initial bios problem, isn't it?? other ways to recover it now?? ,((
- is it a WELL KNOWN PROBLEM when we try to disconnect and replug too hastily the d-bracket headers without switching off the power supply (*my* main erorr here, it seems :( :( ) ????
... and of course, do you think it could have *fried* another key component (cpu, ram -?? why i reminded the setting, just in case-?-, video card? .. ) with that d-bracket initial disconnection error ... ,(
as i said, i have no secondary c2d/ddr2 motherboard here : no way to test the cpu and ddr2 modules on another motherboard to be sure too here. :( i absolutely can't know if they have been damaged or not, here.. :( :(
any other idea for the motherboard itself though ??? ,(
once again, thx a lot for any suggestions and precisions on that problem (is that a COMMON well known problem with the d-bracket, when we unplug and replug it without extrem care like i did -my main inattention error it seems.. mainly because all was so stable before too.. ((( - without shutting down the power supply/system FIRST ???? can it be possible 'only' that shut down all the system??? (( )
thx in advance again +

Is there a new bios coming for P6N SLI Platinum for E8400 ?

Hi everyone,
( My system specs are in the signature )
I have been thinking to upgrade my cpu to E8400, but after some time passing through the forums, internet and asking some of my friends, I have decided not to. This is because I have seen many people frustrated and trying get their E8xxx's working on their moboard with endless efforts because of the wrong information given in the CPU support list of P6N-SLI Platinum. Yet, I have seen that only a few people have managed to get it work but with risky, manual adjustments.
So here is my question, will there be a new bios for P6N SLI Platinum that will make E8xxx series post without any adjustments for the users that want to stick with their P6N SLI Plat.?

Please ask here:
http://ocss.msi.com.tw/

P6N SLI Platinum Won't Load Vista or XP

I trying to load an OS on a new build, but have run into an issue. The build went well, but the OS won't load.
While trying to load Vista (32bit) it says "Loading Operating System" and the progress bar goes all the way to the end but then never gets any further. It just sits there.
So, not being familiar with Vistas load I thought I would tried XP Home SP2. With this I am at least able to partition the drives and choose quick format but once it gets to 20% this too freezes.
So far I have gone into BIOS and chosen to load both safe defaults and optimized defaults, which makes no difference. I have also tried removing one or the other of the memory sticks, again no help.
Here is the system particulars.....
MSI P6N SLI Platinum LGA 775 NVIDIA nForce 650i SLI ATX MB
Intel Core 2 Duo E6600 2.4GHz 775 Processor
Antec Truepower Trio 650w PSU
G.SKILL 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400)
1 - Western Digital Caviar 200GB 7200 RPM SATA 3.0Gb/s Hard Drive
1 - Western Digital Caviar 250GB 7200 RPM SATA 3.0Gb/s Hard Drive
1 - GIGABYTE GeForce 7300GT 256MB GDDR2 PCI Express x16 Video card
1 - DVD drive
1 - Sony Floppy
Everything is brand new. Any help would be greatly appreciated

Quote
Regarding Dual Channel Mode:
Am I reading the manual wrong? In the illustration it shows 4 DIMMS, the closest to the CPU being DIMM1, followed by DIMM3 (which are yellow), then DIMM2 and lastly DIMM4 (which are orange), and it states that in order to take advantage of dual channel to place the memory in DIMMS 1 & 2 and/or DIMMS 3 & 4
Sorry. I did not realize MSI relabeled the DIMMs. You are right of course.
[CPU] - DIMM1 - DIMM23 - DIMM32 - DIMM4
[CPU] - SLOT1 - SLOT2 - SLOT3 - SLOT4

P6N SLI Platinum crashes from cold boot

Intel Core 2 Duo E6420, 2.13GHz, 1,066FSB, 4MB
Zalman CNPS9500-AT Intel LGA775 Aero Flower Cooler
MSI P6N SLI Platinum
Neste ECS 6001 600 watts PSU (3.3V/24A, +5V/30A, +5VSB/3A, +12V1/18A, +12V2/18A, +12V3/18A, +12V4/18A, -12V/0.5A)
2 x 1GB Crucial PC2-5300 Non ECC CL5
XFX GeForce 8600GTS 256MB DDR3 PCIe (PV-T84G-UDF3)
1 x Western Digital Caviar 160GB 7200rpm, S300, 16MB SATA (system disk)
3 x Western Digital Caviar 500GB 7200rpm, S300, 16MB SATA (data disks)
BIOS – 1.1 updated to 1.5, default settings (I'm not overclocking)
Windows XP SP2 OEM
I installed the above system last summer and have been having problems ever since. Initially the video signal dropped after booting so I replaced the graphics card. This didn’t work so I replaced the MOBO. All was OK for a while then the system started crashing for no apparent reason but would usually be OK for a while after re-booting. Then it failed to boot into Windows at all. I checked the BIOS and noticed that the Smart Fan setting in the H/W Monitor had disabled itself somehow (I had set it to be enabled with a target temperature of 40OC). I re-enabled the setting and was able to boot into Windows OK. However it still crashes every time from a cold boot (the CPU fan comes on full speed for a few seconds then the computer just shuts down). After a few re-boots it settles down and seems to be fine.
I’m assuming the problem is something to do with CPU temperature but in the BIOS H/W monitor the system and CPU temperatures are never above 30 to 35OC. As the system seems to be perfectly stable once it’s been re-booted a few times it doesn’t seem that the CPU is actually overheating. I’ve tried setting the CPU target temperature higher (say to 60 OC) but still get the same cold boot crash. Note that the MSI Dual Core Centre utility in Windows shows the same CPU and system temperatures as the BIOS monitor (although the GPU temperature is much higher at 60 OC).
Any suggestions for solving this would be much appreciated.

I'm not familiar with your brand of ps. Have you tested the rails while the system is running using a digital voltage meter?

Who has this setup - MSI P6N SLI Platinum & E8400

This message is intended for anyone who has the MSI P6N SLI Platinum & E8400 in a working state.
I've had the pleasure of perusing these forums for a while in hopes of finding an answer as to why my E8400 isn't working with my P6N SLI Platinum. I've updated my BIOS, I've RMA'd my chip, I've even contacted MSI support (with no reply I might add). I have been so careful when handling these components and thoroughly reading the instructions, to no avail. I've got the board and all components working with a different processor. I've tried the voltage modifications that many have said work, I've tried different memory, I even tried a different video card. So I'm stuck in the same boat as many it seems, however there are one or two posts on this forum and others where people have said they actually got it to work!
So now I really hope I can get this question answered - What is a working config? One of the things I haven't tried yet is a new power supply. My current PS is 650w, but has the 4 pin CPU power connector. From the posts I've read, it shouldn't matter if I have the 4 or the 8. But in reality, does this CPU work on the P6N Plat with an 8 pin connector? I'd be willing to go buy a new PS if thats the case! What else could possibly be the issue? Any and all feedback is appreciated. i really didn't want to start up another thread for this proc/board issue, but perhaps someone else has joined this board by now that may provide the little piece of info that I've been missing.
Cheers,
Aaron

according to the website, the 1.6 BIOS had cpu updates in march so I's assume it would have support for the E8400.
What exactly happens when you turn on the system with the E8400?
-=Mark=-

MediaShield RAID 5 implementation on a P6N SLI Platinum plus boot question

Similar Messages

Maybe you are looking for