Meetingplace server crash and lost the default gateway info

HI all
I have ver 2.0.1.15. I have first eth0 on ip 10.1.1.18 and 2nd eth1 192.168.162.21. will crash and the default gateway on eth0 will be gone. Am i doing something wrong.

Shannon,
Harry is asking you the right question, because a theme with any bad syntax in it (especially custom XSLT files) will get scrapped when the server restarts.
Try to think of something you changed recently, revert it to see of the theme will show up, and try to find the syntax error in your recent changes.
This caught me by surprise when it first happened, but I suppose it is a nice feature. The Wiki Server falls back on a theme that works, which are the built-in ones. It would be nice if the errors were logged instead of just scrapping the theme, but I assume the spirit is to give you a wiki that works, rather than a nicely themed wiki that has errors.

Similar Messages

Computer crashed and lost CS2, what can I do to download again?

How can I download CS2 for the 2nd time as my computer crashed and lost the software?

http://helpx.adobe.com/x-productkb/policy-pricing/creative-suite-2-activation-end-life.htm l

Our exchange server crashed and we lost all contact and calendar data. We found an app to get the contacts off of people's phone to import but can't find the same for calendar. How do I get my calendar info off my phone and in to new exchange server?

Our exchange server crashed and we lost all contact and calendar data. We found an app to get the contacts off of people's phone to import but can't find the same for calendar. How do I get my calendar info off my phone and in to new exchange server?

You'd have to think through this, but it seems like if you are using Outlook, and the items vanished from the Outlook client as well as the server,that you could re-populate Outlook using iTunes.

How to setup default gateway in a DHCP client. The default gateway will be the Ip address of the server that has RRAS installed, hence routing cabalities.

How to setup default gateway in a DHCP client. The default gateway will be the Ip address of the server that has RRAS installed, hence routing cabalities.

Hi Bill,
Thank you for replying back...Yes, I was actually asking how do you set the default gateway address on the DHCP server?,
I believe I got the answer below:
To configure the DHCP default gateway option Click Start, point to Administrative Tools and then click DHCP. In the console tree, expand the applicable DHCP server, expand IPv4, and then right-click Scope Options Click Configure Options, check 003
Router, type the applicable Server name and IP address, and then click OK.
Thank you

How get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?

Hi,
I have a RVS4000 router with DHCP enabled and in router mode.
The LAN is 192.168.2.x. The RVS4000 static IP address is 192.168.2.8
The router is not the RVS4000 and is at 192.168.2.1
The RVS4000 dhcp is assigning it's clients a default gateway of 192.168.2.8 instead of what I want 192.168.2.1.
How can I get the RVS4000's DHCP server to assign another IP address other than its own as the default gateway to its DHCP clients?
Thanks

Hi Gail, you cannot do this. The router, as the DHCP server will only assign a default gateway of what IP interface the DHCP server runs on. If you have the default IP, the gateway is 192.168.1.1. If you create a second vlan, by default it would be 192.168.2.1.
There are not configuration options for the built-in DHCP server. If you'd like to expand this functionality, you would need an external dhcp server.
-Tom
Please mark answered for helpful posts

I ran the program to improve speed and crashing and lost my norton tool bar and vault login

I ran the program to improve speed and crashing and lost my norton tool bar and vault with all my log ins. I am sure it is still here some place but can not find it.

Hi flkeen, Did you try to uninstall that program which you install to improve speed ..see if that works after un install that program....and restore the firefox after uninstalling that program.
see link here for reset firefox https://support.mozilla.org/en-US/kb/reset-preferences-fix-problems?esab=a&s=restore+firefox&r=1&as=s#w_solution-1-reset-firefox-to-its-default-state

HT4914 My pc has crashed and lost a considerable amount of music and videos from iTunes the files are still in iTunes but are empty, will iTunes Match restore my content over the cloud?

My pc has crashed and lost a considerable amount of music and videos from iTunes the files are still in iTunes but are empty, will iTunes Match restore my content over the cloud?

Hm ... I guess I can't edit the post above. Anyway, I seem to have solved it by ...
Quitting iTunes.
Going into Home / Music / iTunes, and renaming the file "iTunes Library.itl" to "iTunes Library (corrupt).itl".
Entering Time Machine, and restoring the "iTunes Library.itl" file from a few days ago. I went back two days, which seemed far enough back to be "before" the problem but not far enough back to have trouble with recent acquisitions.
Re-opening iTunes - and everything seemed to be back in order.
So that's fine for now. We'll see if the solution is stable.
Very, very tentative assignment of blame: I believe iTunes crashed earlier today after I'd synced photos from my iPhone to iPhoto, and then iTunes crashed while iPhoto was closing (and taking its sweet time doing so). If that was indeed the case, that's at least the second time in the past couple of months that trying to sync iPhone photos to iPhoto has caused me significant problems. (The last time led to 80% of my iPhone suddenly being occupied by "Other", and a full restore of the darn thing.)

Weblogic managed server crash and automatic restart on Solaris SPARC platform

hi Everyone,
We are facing a problem a problem with Weblogic managed server where the managed server crashes and automatically restarts (via nodemanager) on Solaris SPARC platform.
The system info is as below:
OS:                            Oracle Solaris 11.1 SPARC
Copyright (c) 1983, 2012, Oracle and/or its affiliates. All rights reserved.
                           Assembled 19 September 2012
uname:SunOS 5.11 11.1 sun4v
(T2 libthread)
rlimit: STACK 8192k, CORE infinity, NOFILE 65536, AS infinity
load average:1.04 0.52 0.32
CPU:total 4 v9, popc, vis1, vis2, vis3, blk_init, cbcond, sun4v, niagara_plus
Memory: 8k page, physical 16777216k(5930008k free)
vm_info: Java HotSpot(TM) 64-Bit Server VM (23.25-b01) for solaris-sparc JRE (1.7.0_25-b11), built on May 15 2013 04:30:17 by "" with Sun Studio 12u1
The pstack output of analyzing the core file is as below (for the particular thread, I can attach the entire output of pstack if required):
--- called from signal handler with signal 11 (SIGSEGV) ---
ffffffff7ec1a7c4 memcpy%sun4v-hwcap3 (103d34720, 10a7e7710, 108ae1060, 6300, 0, ffffffff5f66394b) + 990
ffffffff36102fa4 ZIP_GetEntry (103d34720, ffffffff636f66a4, bd, 103d347f0, a26f1c, 2f) + e4
ffffffff36103440 Java_java_util_zip_ZipFile_getEntry (2b, ffffffff636f66a4, 103d34720, ffffffff636f6b70, 2b, 1) + a8
ffffffff7586ac1c * *java/util/zip/ZipFile.getEntry(J[BZ)J [compiled]
ffffffff75b61b58 * *java/util/zip/ZipFile.getEntry(Ljava/lang/String;)Ljava/util/zip/ZipEntry; [compiled] +39 (line 606)
ffffffff75b61b58 * *java/util/jar/JarFile.getEntry(Ljava/lang/String;)Ljava/util/zip/ZipEntry;+3 (line 452)
ffffffff75b61b58 * *weblogic/utils/classloaders/ZipClassFinder.getSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source;+36 (line 75)
ffffffff75b6eb84 * *weblogic/utils/classloaders/JarClassFinder.getSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +6 (line 100)
ffffffff75a40938 * *weblogic/utils/classloaders/AbstractClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +74 (line 58)
ffffffff75976c88 * *weblogic/utils/classloaders/MultiClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +30 (line 114)
ffffffff75976c88 * *weblogic/utils/classloaders/MultiClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +30 (line 114)
ffffffff75976c88 * *weblogic/utils/classloaders/MultiClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +30 (line 114)
ffffffff75806d10 * weblogic/application/utils/CompositeWebAppFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source;+5 (line 176)
ffffffff75976c88 * *weblogic/utils/classloaders/MultiClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +30 (line 114)
ffffffff75976c88 * *weblogic/utils/classloaders/MultiClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source; [compiled] +30 (line 114)
ffffffff75806d10 * weblogic/utils/classloaders/CodeGenClassFinder.getClassSource(Ljava/lang/String;)Lweblogic/utils/classloaders/Source;+43 (line 48)
ffffffff75806d10 * weblogic/utils/classloaders/GenericClassLoader.findLocalClass(Ljava/lang/String;)Ljava/lang/Class;+87 (line 571)
ffffffff75806d10 * weblogic/utils/classloaders/GenericClassLoader.findClass(Ljava/lang/String;)Ljava/lang/Class;+117 (line 515)
ffffffff75806d10 * weblogic/utils/classloaders/ChangeAwareClassLoader.findClass(Ljava/lang/String;)Ljava/lang/Class;+60 (line 121)
ffffffff75a465c8 * *java/lang/ClassLoader.loadClass(Ljava/lang/String;Z)Ljava/lang/Class; [compiled] +71 (line 836)
ffffffff75db42c0 * *java/lang/ClassLoader.loadClass(Ljava/lang/String;)Ljava/lang/Class; [compiled] +4 (line 714)
ffffffff75806d10 * weblogic/utils/classloaders/GenericClassLoader.loadClass(Ljava/lang/String;)Ljava/lang/Class;+2 (line 358)
ffffffff75806d10 * weblogic/utils/classloaders/ChangeAwareClassLoader.loadClass(Ljava/lang/String;)Ljava/lang/Class;+27 (line 83)
ffffffff7580024c * StubRoutines (1)
ffffffff3691f44c __1cJJavaCallsLcall_helper6FpnJJavaValue_pnMmethodHandle_pnRJavaCallArguments_pnGThread__v_ (ffffffff636f7f98, 10234f000, 2, c, 2, 10) + 2f4
ffffffff36e546c0 __1cJJavaCallsMcall_virtual6FpnJJavaValue_nGHandle_nLKlassHandle_pnGSymbol_63pnGThread__v_ (ffffffff636f7f98, 1013e7748, 10234f000, 10011bf30, 100119ec0, 772d4ec08) + 1b8
ffffffff3725bf0c __1cQSystemDictionaryTload_instance_class6FpnGSymbol_nGHandle_pnGThread__nTinstanceKlassHandle__ (105cb6100, 1013e7978, 10234f000, 102b6e500, 0, 1013e7748) + 494
ffffffff3725a028 __1cQSystemDictionarybEresolve_instance_class_or_null6FpnGSymbol_nGHandle_3pnGThread__pnMklassOopDesc__ (105cb6100, 19dc00, 70, 10234f000, 70, 1013e7700) + ae0
ffffffff37257800 __1cQSystemDictionaryPresolve_or_fail6FpnGSymbol_nGHandle_3bpnGThread__pnMklassOopDesc__ (105cb6100, 1013e76f0, 1013e76f8, 1, 10234f000, 1) + 290
ffffffff368ba9dc __1cTconstantPoolOopDescNklass_at_impl6FnSconstantPoolHandle_ipnGThread__pnMklassOopDesc__ (10201b6e0, 1013e7978, 10234f000, 10201b6e0, 783cfb098, ffffffff37588000) + 264
ffffffff36937380 __1cSInterpreterRuntimeE_new6FpnKJavaThread_pnTconstantPoolOopDesc_i_v_ (10234f000, 77548b730, 49, 10201b6e0, 1013e76e8, 10234f000) + b8
ffffffff7581ab58 * com/jdedwards/base/logging/log4j/JdeLogger.warn(ILjava/lang/String;Ljava/lang/String;Ljava/lang/Object;Ljava/lang/Throwable;)V+14
ffffffff75807bcc * com/jdedwards/system/security/proxy/SecurityServerProxyImpl.install(Ljava/util/Hashtable;)Lcom/jdedwards/system/security/proxy/SecurityServerProxyImpl;+30
ffffffff75806d10 * com/jdedwards/system/security/proxy/SecurityServerProxyFactory.create(Ljava/util/Hashtable;)Lcom/jdedwards/system/security/SecurityServer;+1
ffffffff75807898 * com/jdedwards/system/security/SecurityServerInstance.getInstance()Lcom/jdedwards/system/security/SecurityServer;+27
ffffffff75806d10 * com/jdedwards/mgmt/security/UserManager.checkPassword(Ljava/lang/String;Ljava/lang/String;)Z+59
ffffffff75806b24 * com/jdedwards/mgmt/security/UserManagerImpl.checkPassword(Ljava/lang/String;Ljava/lang/String;)Z+5
ffffffff75806b24 * com/jdedwards/mgmt/security/SCFLoginModule.login()Z+481
The output of the hs_err_pid1127.log file is as below:
# A fatal error has been detected by the Java Runtime Environment:
# SIGSEGV (0xb) at pc=0xffffffff7ec1a544, pid=1127, tid=20
# JRE version: 7.0_25-b11
# Java VM: Java HotSpot(TM) 64-Bit Server VM (23.25-b01 mixed mode solaris-sparc compressed oops)
# Problematic frame:
# C [libc.so.1+0x11a544] memcpy%sun4v-hwcap3+0x710
# Core dump written. Default location: /slot/ems9437/appmgr/Oracle/Middleware/user_projects/domains/smc_domain/core or core.1127
# If you would like to submit a bug report, please visit:
#   http://bugreport.sun.com/bugreport/crash.jsp
# The crash happened outside the Java Virtual Machine in native code.
# See problematic frame for where to report the bug.
--------------- T H R E A D ---------------
Current thread (0x000000010294d000): JavaThread "[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'" daemon [_thread_in_native, id=20, stack(0xffffffff62f00000,0xffffffff63000000)]
siginfo:si_signo=SIGSEGV: si_errno=0, si_code=1 (SEGV_MAPERR), si_addr=0xffffffff5f6ce000
I ran the suspect code which i believed was causing the issue as a standalone Java program using the same Java executable and it worked fine without any crash.
Appreciate any inputs / discussion / feedback / thoughts on this topic.
Good day.

I just wanted to throw in one more thought. I have also seen that there is a restart=true parameter. Maybe if we set this to true, and just issue the command to shut down the server in the script, the managed server will restart on its own.
Would greatly appreciate any advice!

System crashed and lost library, want to recover

system crashed and lost library, want to recover

Welcome to the Apple Discussions. I don't know how to fix the xml file or prevent it's damage except to keep a current backup copy of the domain.sites2 file. You can do that on an hourly basis with Time Machine or use a backup application like Synk Standard which can do incremental backup (i.e. copy just those new or changed files) at any time.
As for separating the sites into their own domain files I use iWebSites to manage over 75 individual sites. It lets me create multiple sites and multiple domain files.
If you have multiple sites in one domain file here's the workflow I used to split them into individual site files with iWebSites. Be sure to make a backup copy of your original Domain.sites files before starting the splitting process and move it to another location on your HD until you're satisfied the separation process is completed and what you want.
This lets me edit several sites and only republish the one I want.
There is a downside to this method if you're publishing to MobileMe. When publishing multiple sites to MMe from their own separate domain file the last published site will be the default site when using the default URL for that MMe account: http://web.me.com/MobileMeAccountName/. That could mess up any CNAME forwarding if you have a domain name pointed to your default MMe site.
OT

Cascading RV180 as DHCP server but pointing to another default gateway router

Hi,
My network topology is as follows:
Internet <-> Residential Gateway (RG) from ISP (OEM: Pace) [192.168.1.254/255.255.255.0] <-> RV180 [192.168.1.253/255.255.255.0] <-> SG500 switch [192.168.1.250/255.255.255.0] <-> rest of network.
I know this is a cascading LAN-to-LAN arrangement. The cable from the RG to the RV180 is from a LAN port on the RG to a LAN (not WAN) port on the RV180.
I eventually want to segment my network into a few VLANs from the RV180 down. I am aware most people would recommend DHCP on the "primary" router, but the RG is non-VLAN aware, so I figure I need to handle the DHCP off the RV180. At the same time, I have also opted not to do a LAN-to-WAN cascade because I want to retain the ability to configure the RG from the rest of the network and not have to cart a computer over to the RG to do it.
On the RG, I've disabled DHCP, and placed 192.168.1.253 in the DMZ.
On the RV180, I've enabled DHCP and put it in Router mode.
The issue is that I do not have any Internet connectivity. If I allow the computers in the network to receive IP addresses over DHCP, the default gateway that is communicated is 192.168.1.253, which is the RV180. If I configure static IPv4 information on my computers to point to 192.168.1.254, I am able to connect outside, as you would expect.
How can I get the RV180 to pass out DHCP IP addresses, but point to 192.168.1.254 as the default gateway? I thought the solution might be to create a default route (or something). I went to the static routes tab but it wouldn't let me enter 0.0.0.0 as a destination IP to route through 192.168.1.254.
Further down the line, is it possible for both the RG and the RV180 to connect directly to the SG500, along with the other nodes in my network? That way the RV180 only serves to maintain the VLANs and pass out IP addresses via DHCP, instead of having it be the choke through which everything goes through on the way out?
Sorry if there is a really obvious solution to this. It's really been floundering about in the dark so would appreciate any advice

Hi Jason, I have considered your post here for quite some time. I came to one conclusion based off your text. The entire purpose of the RV180 is a DHCP server for multiple subnet / vlan.
Here's the thing, you have a SG500 switch. Based off reading your text, this will do everything the RV180 can except the DHCP service. The limitation you are going to run in to is still going to be your gateway unit, the RG.
In the end, even with such a configuration using the RV!80 or the SG500 (layer 3), the RG will have to be configured with static routes since the RG has no concept of those other LAN segments.
Here is a post I wrote about a SG300 connecting to a RV0XX router (which doesn't understand the VLANs)
https://supportforums.cisco.com/message/3739083#3739083
Using the concept of this topic, you may be able to add aditional static routes on the RV180 sending each subnet to the common IP interface of the RG.
It would be very interesting to see if we could make that work.
-Tom
Please rate helpful posts

WRT350N : how to specify the default gateway?

Hello,
I would like to use my wrt350n as a dhcp server, but want to specify another router as the default gateway.
I have my wrt350n (192.168.1.254) and another modem/router (192.168.1.1). When a client connects to the wrt350n, it automatically receives as default gateway the adress of the wrt350 (192.3168.1.1). I would like to change that to reference the other adress 192.168.1.1.
Thanks for your comments
Raph
Solved!
Go to Solution.

Hello,
Thanks for your answer.
I try to give you more information.
The modem router (bbox2 : 192.168.1.1) is connected to an ethernet port on the WRT350 (192.168.1.254). I would like to desactivate the DHCP server on the bbox2 (because limited to 802.11g), and activate it on the wrt350, to have a wireless network in 802.11n. The problem when I do that, is at the dhcp server, the default gateway returns is always the ip adress of the wrt350 (so no internet access). Nevertheless, I have to specify the ip of the bbox (192.168.1.1) for the internet traffic. I don't find a way to change the value of the default gateway returns by the wrt350. I can set different values for DNS, but not for the gateway.
Actually, I turn on the dhcp server on the bbox and turnoff it on the wrt350, but my wireless spped is limited to 54Mbits (802.11g), and this not annoying for surfing purpose, but annoying when streaming video from my san connected to the wrt350n.
I don't know if it's clear now?
Thanks for your feedback

The Default Gateway Is Not Available / Problem

Hello, I recently purchased this HP Pavileon laptop, and I've been encountering this problem very often (every 2-10 minutes). This problem is getting extremely frustrating as absolutely nobody has been able to provide a fix for this issue.
When the laptop is on battery mode (this does not happen when plugged in); I commonly get disconnected from my wi-fi connection and to fix it, I must run the troubleshooter. This temporarily fixes the issue by resetting the wi-fi adapter.
What I have tried and has not worked:
* Turn off to save power option in the driver settings (in Device Manager) untickets
* Updated drivers
* New power plan
* Tried different drivers
* Complete system restore
The wireless adapter is Realtek RTL 8188EE. Upon running the troubleshooter, this is all the information from the detailed information section:
Windows Network Diagnostics
Publisher details
Issues foundThe default gateway is not available
The default gateway is not availableThe default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Fixed
Reset the "WiFi" adapter
Completed
Investigate router or broadband modem issues
Not run
Issues found
Detection details
6The default gateway is not availableFixed
The default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Reset the "WiFi" adapterCompleted
This can sometimes resolve an intermittent problem.
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Repair.1.etl Investigate router or broadband modem issuesNot run
If you're connected to a hotspot or domain network, contact the network administrator. Otherwise: 1. Unplug or turn off the device. 2. Once all the lights on the device are off, wait at least 10 seconds. 3. Turn the device on or plug it back in to the power outlet. To restart a router or modem that has a built-in battery, press and quickly release the Reset button.
Detection details
Diagnostics Information (Network Adapter)
Details about network adapter diagnosis:
Network adapter WiFi driver information:
Description . . . . . . . . . . : Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Manufacturer . . . . . . . . . : Realtek Semiconductor Corp.
Provider . . . . . . . . . . . : Realtek Semiconductor Corp.
Version . . . . . . . . . . . : 2012.2.827.2013
Inf File Name . . . . . . . . . : C:\WINDOWS\INF\oem8.inf
Inf File Date . . . . . . . . . : 12 September 2013 10:17:00
Section Name . . . . . . . . . : HP8188ee.ndi
Hardware ID . . . . . . . . . . : pci\ven_10ec&dev_8179&subsys_197d103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2014-07-24 04:19:49-759
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 0 item(s) total, 0 item(s) displayed
Connection History
Information for Auto Configuration ID 1
List of visible networks: 1 item(s) total, 1 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> Yes 100 Yes Matt
List of preferred networks: 1 item(s)
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Information for Connection ID 1
Connection started at: 2014-07-24 04:19:49-759
Auto Configuration ID: 1
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): No
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 98-fc-11-88-61-b8
Security and Authentication
Configured security type: WPA2-PSK
Configured encryption type: CCMP(AES)
802.1X protocol: No
Key exchange initiated: Yes
Unicast key received: Yes
Multicast key received: Yes
Number of security packets received: 0
Number of security packets sent: 0
Security attempt status: Success
Connectivity
Packet statistics
Ndis Rx: 34302
Ndis Tx: 32619
Unicast decrypt success: 0
Multicast decrypt success: 0
Unicast decrypt failure: 0
Multicast decrypt failure: 0
Rx success: 0
Rx failure: 0
Tx success: 0
Tx failure: 0
Tx retry: 0
Tx multiple retry: 0
Tx max lifetime exceeded: 0
Tx ACK failure: 0
Roaming history: 0 item(s)
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Result of diagnosis: There may be problem
Diagnostics Information (Wireless Network Adapter)
Details about wireless network adapter diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Native WiFi MSM
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: There may be problem
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Diagnose.0.etl
Other Networking Configuration and LogsFile Name: NetworkConfiguration.cab Collection information Computer Name: LAPTOP Windows Version:6.3Architecture:x64Time:24 July 2014 04:34:47
Windows Network Diagnostics Detects problems with network connectivity. Package Version:1.0Publisher:Microsoft Windows

Run the HP Support Asssitant's Tune up application. There should be a new BIOS available. sp66866
Have you installed the latest Windows 8.1 updates?
Do not install optional video graphics updates.
I was runnning into a similar problem with my HP product loan Envy Spectre 13 TouchSmart Ultrabook until I did the updates. I had upgraded my wireless router to a model with 802.11AC specification.
Invoke the Device Manager and ensure that the box next to Allow this computer to turn off this device to save power is unchecked.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

I have transfered all my library on an external hard disk and lost the itunes library files.

I transfered all my library on an external hard disk and lost the itunes library files. Itunes created new ones but I lost all the playlists.
How can I copy the playlists presents on the Iphone directly on Itunes ?
If I want to syncronise now, I lost all playlists datas.

Hi,
I did the same XP to Windows 7 upgrade about 18 months ago. I decided to keep iTunes permanently on the external drive than the c drive to save c: drive space.
ITunes database has pointers to MP3 files located in Artist's directories. If you want to use a different location than the default C:\ drive for iTunes, then you need to recreate the Itunes database by deleting all songs in iTunes, then change the default location for iTunes files to your external drive. Then import the MP3 files from the external drive into the empty iTunes database through the iTunes import facility.
If you screw up the timing of the import and find you have multiple iTunes directories (instead of just the default location), then iTunes has a new feature to consolidate all iTunes MP3 files back into the central default location. In iTunes, FILE, LIBRARY, ORGANIZE LIBRARY, then CONSOLIDATE FILES.
To change the default directory for MP3 files, in Tunes go to EDIT, PREFERENCES, ADVANCED and then CHANGE the location to where you want the Itunes MP3 files to be located (including the iTunes subdirectory under which all the artist directories are held. Mine are on the F: drive or whatever your computer states is your drive assignment for the external drive.
Note iTunes 10.5 has many problems that Apple hopefully are working on....we seem to have gone backwards on working components in this iCloud based release. So maybe keep on using old computer until 10.6 is released.
Enjoy
Steve Mc (Sydney AUSTRALIA)

HT203167 my computer crashed and lost my itunes, now i have a new computer...is there any way to get my music back from my account

my computer crashed and lost my itunes, now i have a new computer...is there any way to get my music back from my account

It has always been very basic to always maintain a backup copy of your computer for just such an occasion.
Use your backup copy to put everything back.
If for some reason you have failed to backup, not good, then you can redownload some purchases in some countries.
Downloading past purchases from the App Store, iBookstore, and iTunes Store

Imported photos, deleted originals, then iphoto crashed and lost everything

I imported photos from my iphone, deleted the originals (i never do this, but figured, it's a new year so i should start cleaning up my phone!), and then iphoto crashed and now the photos i imported are nowhere to be found! help!

Welcome to the Apple Discussions. There's still a good chance that the photos are in the library but just not being recognized by iPhoto. Backup the library and try the three fixes below in order as needed:
Fix #1
Delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your User/Library/Preferences folder.
NOTE: If you're moved your library from its default location in your Home/Pictures folder you will have to point iPhoto to its new location when you next open iPhoto by holding the the Option key. You'll also have to reset the iPhoto's various preferences.
Fix #2
Launch iPhoto with the Command+Option keys depressed and follow the instructions to rebuild the library. Select last three options.
Click to view full size
Fix #3
Rebuild the library using iPhoto Library Manager as follows:
Using iPhoto Library Manager to Rebuild Your iPhoto Library
1 -Download iPhoto Library Manager and launch.
2 -Click on the Add Library button, navigate to your User/Pictures folder and select your iPhoto Library folder.
3 - Now that the library is listed in the left hand pane of iPLM, click on your library and go to the File->Rebuild Library menu option
4 - In the next window name the new library and select the location you want it to be placed.
5 - Click on the Create button.
Note: This creates a new library based on the LIbraryData.xml file in the library and will recover Events, Albums, keywords, titles and comments but not books, calendars or slideshows. The original library will be left untouched for further attempts at fixing the problem or in case the rebuilt library is not satisfactory.
OT
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier versions) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
NOTE: this is not the same as routinely backing up your entire iPhoto library folder to protect your photos. It only protects the loss of your organizational efforts that the database file contains.
I've created an Automator workflow application (requires Tiger or later), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. There are versions that are compatible with iPhoto 5, 6, 7 and 8 libraries and Tiger and Leopard. Just put the application in the Dock and click on it whenever you want to backup the dB file. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.
NOTE: The new rebuild option in iPhoto 09 (v. 8.0.2), Rebuild the iPhoto Library Database from automatic backup" makes this tip obsolete.

Meetingplace server crash and lost the default gateway info

Similar Messages

Maybe you are looking for