MeetingPlace WebEx-scheduling and +country code

How is that possible in Meetingplace WebEx-scheduling installation add + to the country code in Access Information (Cisco WebEx Site Configuration)?
I tried to add + and \+ to dial-in nummber but I got "Phone number format is invalid" error.
Any ideas?
Ali.

Hi Ali,
On this page you don't add + , on this page use this format:
1-408-XXX-XXXX
but when you do a dialout via WebEx to PSTN phones that time call will come to CUCM as +Called Phone number so you need to have translation patter in CUCM to take off that leading '+' and send call without '+' to your PSTN provider.
HTH
Arun

Similar Messages

Airport Extreme 802.11n reports incorrect Locale and Country Code

I have just replaced my MacBook Pro CoreDuo's Airport Extreme card with a Mac Pro one that gives excellent throughput with 802.11n but, depending upon which channel it connects to the wireless router, System Profiler displays a weird selection of locales and country codes (e.g. locale: RoW, country code X2) .... perhaps this does't matter ... perhaps it does as other threads here report not being able to make a connection when an available channel is supposed not to be available in the incorrectly reported country.
What controls this (incorrect) choice and how can it be fixed?
System Profile of en1:
Card Type: AirPort Extreme (0x14E4, 0x88)
Firmware Version: Broadcom BCM43xx 1.0 (5.10.91.19)
Locale: RoW
Country Code: X2
Supported PHY Modes: 802.11 a/b/g/n

AirPort-Guy wrote:
The Locale is programmed into the card. If you bought your Mac Pro in a country other than where you are currently living, and you are using the card that came with it, you could be violating your country's wireless regulations.
Actually this is not entirely correct.
Rather the Mac sets its AirPort country code based upon the first beacon packet containing regulatory domain information received when the Mac starts passively listening to incoming packets after the AirPort interface is enabled.
RoW does stand for "rest of world" and the "X" domains are temporary used ones when searching for regulatory domain information.
So if you're seeing your Mac's AirPort card programmed to a different country code regulatory domain than it should be, it's because someone near you is using an illegal wireless access point/router.

FSCM: matching business partner and country code

Hello FSCM community,
simple task!? In FSCM i want to find all businesspartners matching a certain country code (e.g. all businesspartners with country code equals 'FR'. Since kna1 doesn't provide the data wanted, there has to be a different table.
Questions:
1. is there a standard transaction to find those BPs?
2. what are the technical / table-/view/...../-names in FSCM to find those BPs by transparent table?
Looking forward to hear from You!
Thanks in advance!
Gunther

Hi,
Look at table BUT020. Here enter the partner number (field PARTNER), where you will get the business partner Address number (field ADDRNUMBER). Input this address number in ADRC table and you will get the country in field LAND1.
There is no one single table from where you will get this information, you will need to build a query.
Cheers.

AAR and Country Codes

Hi all,
We are about to deploy CallManager 4.1(3) in Europe, supporting several offices:
Paris (country code 33)
Munich (country code 49)
London (country code 44)
My question is about using AAR between these offices. Let's assume we have the following dial plan:
Paris: ext. 1111, external phone number 1111-1111
Munich: ext. 2222, external phone number 2222-2222
London: ext. 3333, external phone number 3333-3333
If Paris is dialing Munich and AAR kicks in, Paris will need to dial access code (00) + country code (49) + Ext. Phone Number (2222-2222).
I can put the 00 in the AAR Group, however I can't put the 0049 in the AAR group, because if Paris needs to dial London in the same scenario they will need to dial access code (00) + country code (44) + Ext. Phone Number (3333-3333).
I think each physical phone can only get 1 AAR group.
It appears to me I have two choices:
1. Put the country code in the External Phone Mask config, so (for example) Munich's Ext. Phone Number would be 49-2222-2222 and London's would be 44-3333-3333. The Paris' AAR Group would simply be 00.
2. Put translation patterns in each office. So - in AAR - when Paris dials 00-2222-2222 I translate it to 00-49-2222-2222 and when they dial 00-3333-3333 I translate it to 00-44-3333-3333.
#2 seems like it does not scale well at all. #1 seems to work well, does anyone have any suggestions? Has anyone hit this before?
Thanks - Rob.

AAR group dialing prefixes are used between two groups at any time. So you can define the country codes in the AAR prefix specified in the group.
So you will have three AAR groups (each go under the appropriate phone's line configuration)
AARParis will use 0049 to AARMunich
AARMunich will use 0033 to AARParis
AARParis will use 0044 to AARLondon
AARLondon will use 0049 to AARMunich
AARMunich will use 0044 to AARLondon
AARLondon will use 0033 to AARParis.
Refer to SRND for best practices on AAR.
http://www.cisco.com/application/pdf/en/us/guest/netsol/ns268/c649/ccmigration_09186a0080479538.pdf
HTH
Sankar
PS: please remember to rate posts!

Get Locale country and language codes

I have checked the documentation, but nothing is jumping out
at me. Is there a function that returns the locale country and
language codes? GetLocale() returns the "locale name as it is
represented in ColdFusion":
ie:
English (US)
Spanish (Standard)
What I am looking for is the
ISO
codes
en US
es ES
I can get the information using getPageContext(), but just
wondered if I was overlooking a built-in CF function.

-==cfSearching==- wrote:
> The problem with the functions I have seen is that they
return
locale name
> as it is represented in ColdFusion (ie English (US)
). But what I am
> looking for the ISO language and country codes.
...hmm this didn't go thru on the 16th. let me try again.
that should only be for the "traditional" cf supported
locales (backwards
compatibility is always foremost in the cf team's minds), the
rest should be in
normal java style locale ID (th_TH, ar_AE, etc).
no, there's nothing built-in in cf for what you want. you'll
have to dip down
into java:
<cfscript>
localeObj=createObject("java","java.util.Locale");
locales=localeObj.getAvailableLocales();
writeOutput("<table border='1'>");
writeOutput("<tr align='center'><td
colspan='2'>Locale</td><td>Language</td><td>Country</td></tr>");
for (i=1; i LTE arrayLen(locales);i=i+1) {
thisLocale=locales
thisLanguage=thisLocale.getLanguage();
thisCountry=thisLocale.getCountry();
writeOutput("<td>#thisLocale.toString()#</td><td>#thisLocale.getDisplayName()#</td><td>#t hisLanguage#</td><td>#thisCountry#</td></tr>");
writeOutput("</table>");
</cfscript>
note that this snippet doesn't show variants (eg. th_TH_TH)
& shows language
only locales (en, fr, etc.), nor is it sorted in any order i
can recognize. also
keep in mind that what this shows depends on the server's JRE
version. if you
want a "better" source of locales, use the icu4j lib's
ULocale class. it's based
on the latest CLDR & contains way more locales (and they
actually tend to fix
locale bugs in your lifetime).

Macbook Pro 15 Change Country Code to get 11n and 300 Mbit/s

Hello All!
I have a question: how can I change Country Code on my MBP 15" to get wi-fi 11n mode and 300 Mbit/s (or at least 130) with my TL-WR1043ND router. I've changed the Region setting in the web interface of my router, but it didn't solve the problem. And there is a wonder but my macbook 13" has Country Code: X2 (sometimes FR) and use 11n mode with transmit rate: 130 Mbit/s. So, as for me, that is very strange dependence — Country Code and Connection Speed.
System info:
Router preferences:
Thanx!

So, I have MBP 15-inch, Mid 2010 and MB 13-inch, Mid 2009. And, as I said before, MB 13 doesn't have the problem with 11g mode, it has Contry Code X2 or sometimes FR, but never UA. And the MB13 is older then the MBP15. Maybe problem is in the router, but I don't know how figure out it. And I don't understand, at all, the dependence Transfer Rate and Country Code — why software is restrict connection speed of hardware?

Lightroom 4 GPS/ Country Code questions

1. If you import an image with GPS data, Lightroom 4 will add appropriate values for Sublocation, City, State/Province, Country and Country Code. Is there a way to add this data to existing files while retaining history?
You can write metadata to files ([Ctrl][S]), remove those files from Lightroom and then synch folder to reimport them. That reimports them with all modifed settings but without their history. Is there another way that retains the history?
2. Is a google map link available for a GPS location of a photograph?
In Lightroom 3, you could click on the GPS location and that took you to a Google map page with a specific web link that you could then publish, eg on a blog. You can copy and paste the GPS location into a Google map page but that does not give you a web link you can use.
3. Is there a way of publishing a map?
Is there (or will there be) any way of exporting a map page, say as a jpeg?
Is it OK to take a screen dump of a map page and publish it, eg in a blog?

Ian Lyons wrote:
1. There is no way of saving history to the file.
I've worked it out. There is a way of updating location descriptions for existing images in Lightroom 4 from the GPS setting.
If you select some images with the same GPS location and [Synch Metadata] for GPS, this fills in the location descriptions, even if none of the images have them to start with.
There are then two ways of doing this for a Folder of images:
(1) Modifying in Library
Select a bunch of images taken in the same place and therefore with the same GPS setting. You can check that the GPS settings are the same because under Metadata in the right-hand tab it will show a single GPS location rather than "<mixed>".
[Synch Metadata] for GPS.
Repeat for different locations.
If you have a single image in a location, you'd need to create a virtual copy, [Synch Metadata] for GPS, then delete the virtual copy.
(2) Modifying through re-import
This method is more complex but may be quicker where there are many GPS locations.
It is probably a good idea to first ensure you have a current backup, or backup to a catalogue, in case anything goes wrong.
Select images with no changes to Develop settings: click the Metadata filter (Library/ Grid mode) and then filter for Develop Preset = "Default Settings".
Write metadata for these images to files
[Ctrl][S]
(unless you already do this with every image change)
Remove the selected images from the Lightroom catalogue: click [Delete] and then select [Remove] (do not [Delete from Disk]).
Reimport the images: right-click the folder for the images and select [Synchronise Folder ...].
All the images with no Development changes will now have location descriptions.
Now you can update the images with Development changes without affecting the History.
Filter for Develop Settings = "Custom",
select an image (or several at the same location),
filter for Develop Settings = "All" and
synch GPS settings from an adjacent image with location descriptions.

Change in Country code does not get reflected in iTunes in iPhone

Hi,
I just moved to USA from India. In my apple id, I changed the contact info, and country code and ofcourse the payment card details. Then I synced up my iPhone on my laptop. When I try to search the apps (Bank Of America Mobile Banking) which are available on USA Store are not visible on my iTunes app on iPhone. But they are visible in iTunes on my laptop.
I have rebooted my iPhone, laptop and then synced them. Still the issue remains.
Thanks in Advance
Anand

I got it..
Just tried to install an free application which was available in India store. Then I got a message saying I cannot use store from this country and it took me to USA store. From there I could download necessary app from USA store.

Change the Mobile Country code and Mobile Network code BB sprint style 9670

I need to have a Sprint BB Style 9670 unlocked & Mobile Country code to use on Indian CDMA networks. It doesn't have a SIM card. Anyone have this problem or can point me to the proper way to unlock it? I chatted with Sprint but they don't want to do anything
Mukesh

Hi and Welcome to the Community!
Please refer to this helpful thread:
http://supportforums.blackberry.com/t5/General-BlackBerry-Functions-and/Unlocking-your-BlackBerry-Gu...
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

My phone does not show contact names for country and area code while having in coming calls. Although, I have endorsed the name with numbers. How do I the problem. My one is a iphone 3s device with updated os. Please text to help

My iphone does not recognize saved contact number while having incoming calls due to country and area code as auto prefix. How do i fix the problem. How do i ensure that the phone recognize calls with and without the country and area code. Please text to help.

1) Open the Phone and dial *228. This is a Verizon over-the-air programming number.
2) When the system answer press 1 for "Program or activate your phone"
3) Wait for the call to disconnect. You should get a prompt stating something like, "Settings updated."
4) Open the Task Manager and kill the Phone, Message, and Contacts Applications
5) Wait a few minutes (I waited 3 just to be extra safe)
6) Open the Message App to verify the fix

I recently moved from the US to Sweden and all my contacts are saved with their international country code prefixes. I keep getting text message errors when I send a text, but the contact info is stored correctly for each. How can I fix this?

I receive an error message that adds the country code again. I tried it with no country code and the area code included but I still receive an error message. It only does it sometimes and not to all Sweden contacts. There is no obvious reason why it does it to some but not others. Does any know what the problem is and how to fix it? Thank you!

Only other thing I can suggest is to reset your phone. This won't touch any data or settings:
Press the sleep/wake button & home button at the same time, keep pressing until you see the Apple logo, then release.

To get the company code and country grouping attached to a position

Hi everyone,
I have a position and I need to get the company code and the country grouping that this position is attached to. Could you kindly suggest an FM or a class which would fetch the above data keeping in mind the inheritance tree. That is, if the company code is not maintained in HRP1008, then it should look for the same in the Org Unit that this position belongs to and so on..
Any help will be greatly appreciated.
Regards,
Alpana.

Hi
Check the A011 relationship of the position and get the cost center, from cost center you can get the company code and country grouping from Cost Center Master CSKS.
~~~Ganesh Kumar K.

VAT registration number in combination with country and company code

Hi,
Is there configuration where we can define the VAT registration number with combination of country and company code.
thanx in advance

Hi,
Thanx for the reply.bt the issue is like we have a condition type zvat where condition table have the following fields departure country and destination country,The country of our company code is GB and we maintain a record for condition type zvat i.e GB (departure country) to GB (destination country) 17.5%.While creating a contract if vat is applicable we told user to maintain country GB in both the fieds i.e tax departure country and tax destination country in billing tab at header level of the contract .It is working fine for other company where company code country is different then GB.But for this where company code country is GB.An error occurs i.e.There is no vat registration number fot this comapny code XXXX for country GB.
Now how should i go about it?

A table mapping between ISO country code and ISO currency code

Hi experts,
I want to know whether there is a table mapping between ISO country code and ISO currency code.I have searched T005(Countries) and TCURC(Currency Codes).why the filed of WAERS(Country currency) hasn't maintained in talbe T005?Whether ISO country code and ISO currency code hasn't direct relation?
Regards,
Kelvin

Kelvin,
If you know the table which is having ISO Country Code or ISO Currency code,then go to that table and clik on GRAPHIC(ctrlShiftf11) which will give the foreign key relationships.I guess checking all those table displayed in the graphic will give you some lead.
K.Kiran.

A table mapping between country code and currency code

Hi experts,
I want to know whether there is a table mapping between country code and currency code.I have found the table T005(Countries).But I don't why the filed of WAERS(Country currency) hasn't maintained in talbe T005?Whether country code and currency code hasn't direct relation?
Regards,
Kelvin

Dear Kelvin
The said field (WAERS) can be fetched from many tables. To name a few, below are some of the tables in which, you can see the field for currency.
1) BKKI4
2) BKKI5
3) BWPOS
4) KNKA
5) KNVV
6) MSEG
thanks
G. Lakshmipathi

MeetingPlace WebEx-scheduling and +country code

Similar Messages

Maybe you are looking for